From 8c059a4676038967dd6efe614538c329b61e68a1 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 15 Nov 2017 11:52:32 -0800 Subject: spi: imx: Update device tree binding documentation Update documentation for gpio-cs and num-cs to reflect the standard SPI bindings. The dma properties are optional. Include a warning that native CS do not work in a commonly useful manner with this hardware/driver, and therefor most users probably should use GPIO based CS lines rather than native. CC: Mark Brown CC: Shawn Guo CC: Sascha Hauer CC: Fabio Estevam CC: Oleksij Rempel Signed-off-by: Trent Piepho Signed-off-by: Mark Brown --- Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 5bf13960f7f4..e3c48b20b1a6 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -12,24 +12,30 @@ Required properties: - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" See the clock consumer binding, Documentation/devicetree/bindings/clock/clock-bindings.txt -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "tx" and "rx" if present. -Obsolete properties: -- fsl,spi-num-chipselects : Contains the number of the chipselect +Recommended properties: +- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip +select lines can be used, they appear to always generate a pulse between each +word of a transfer. Most use cases will require GPIO based chip selects to +generate a valid transaction. Optional properties: +- num-cs : Number of total chip selects, see spi-bus.txt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names, if present, should include "tx" and "rx". - fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register controlling the SPI_READY handling. Note that to enable the DRCTL consideration, the SPI_READY mode-flag needs to be set too. Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { -- cgit v1.2.3-59-g8ed1b From 5a1314fa697fc65cefaba64cd4699bfc3e6882a6 Mon Sep 17 00:00:00 2001 From: Ricardo Ribalda Date: Tue, 21 Nov 2017 10:09:02 +0100 Subject: spi: xilinx: Detect stall with Unknown commands When the core is configured in C_SPI_MODE > 0, it integrates a lookup table that automatically configures the core in dual or quad mode based on the command (first byte on the tx fifo). Unfortunately, that list mode_?_memoy_*.mif does not contain all the supported commands by the flash. Since 4.14 spi-nor automatically tries to probe the flash using SFDP (command 0x5a), and that command is not part of the list_mode table. Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads into a stall that can only be recovered with a soft rest. This patch detects this kind of stall and returns -EIO to the caller on those commands. spi-nor can handle this error properly: m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404 m25p80 spi0.0: SPI transfer failed: -5 spi_master spi0: failed to transfer one message from queue m25p80 spi0.0: s25sl064p (8192 Kbytes) Signed-off-by: Ricardo Ribalda Delgado Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-xilinx.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/spi/spi-xilinx.c b/drivers/spi/spi-xilinx.c index bc7100b93dfc..e0b9fe1d0e37 100644 --- a/drivers/spi/spi-xilinx.c +++ b/drivers/spi/spi-xilinx.c @@ -271,6 +271,7 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) while (remaining_words) { int n_words, tx_words, rx_words; u32 sr; + int stalled; n_words = min(remaining_words, xspi->buffer_size); @@ -299,7 +300,17 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) /* Read out all the data from the Rx FIFO */ rx_words = n_words; + stalled = 10; while (rx_words) { + if (rx_words == n_words && !(stalled--) && + !(sr & XSPI_SR_TX_EMPTY_MASK) && + (sr & XSPI_SR_RX_EMPTY_MASK)) { + dev_err(&spi->dev, + "Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n"); + xspi_init_hw(xspi); + return -EIO; + } + if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) { xilinx_spi_rx(xspi); rx_words--; -- cgit v1.2.3-59-g8ed1b From 251c201bf4f8b5bf4f1ccb4f8920eed2e1f57580 Mon Sep 17 00:00:00 2001 From: Maxime Chevallier Date: Mon, 27 Nov 2017 15:16:32 +0100 Subject: spi: a3700: Fix clk prescaling for coefficient over 15 The Armada 3700 SPI controller has 2 ranges of prescaler coefficients. One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by steps of 2. This commit fixes the prescaler coefficients that are over 15 so that it uses the correct range of values. The prescaling coefficient is rounded to the upper value if it is odd. This was tested on Espressobin with spidev and a locigal analyser. Signed-off-by: Maxime Chevallier Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-armada-3700.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c index 77fe55ce790c..d65345312527 100644 --- a/drivers/spi/spi-armada-3700.c +++ b/drivers/spi/spi-armada-3700.c @@ -79,6 +79,7 @@ #define A3700_SPI_BYTE_LEN BIT(5) #define A3700_SPI_CLK_PRESCALE BIT(0) #define A3700_SPI_CLK_PRESCALE_MASK (0x1f) +#define A3700_SPI_CLK_EVEN_OFFS (0x10) #define A3700_SPI_WFIFO_THRS_BIT 28 #define A3700_SPI_RFIFO_THRS_BIT 24 @@ -220,6 +221,13 @@ static void a3700_spi_clock_set(struct a3700_spi *a3700_spi, prescale = DIV_ROUND_UP(clk_get_rate(a3700_spi->clk), speed_hz); + /* For prescaler values over 15, we can only set it by steps of 2. + * Starting from A3700_SPI_CLK_EVEN_OFFS, we set values from 0 up to + * 30. We only use this range from 16 to 30. + */ + if (prescale > 15) + prescale = A3700_SPI_CLK_EVEN_OFFS + DIV_ROUND_UP(prescale, 2); + val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG); val = val & ~A3700_SPI_CLK_PRESCALE_MASK; -- cgit v1.2.3-59-g8ed1b From 8d26fdfcb45dc420115b267ac9d6b3ac13457f1b Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 30 Nov 2017 14:35:08 +0100 Subject: spi: Fix double "when" Signed-off-by: Geert Uytterhoeven Signed-off-by: Mark Brown --- include/linux/spi/spi.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 7b2170bfd6e7..bc6bb325d1bf 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -126,7 +126,7 @@ void spi_statistics_add_transfer_stats(struct spi_statistics *stats, * for that name. This appears in the sysfs "modalias" attribute * for driver coldplugging, and in uevents used for hotplugging * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when - * when not using a GPIO line) + * not using a GPIO line) * * @statistics: statistics for the spi_device * -- cgit v1.2.3-59-g8ed1b From b458a3490e46dddd5b63f59b458c9b6d2284a63f Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 7 Dec 2017 11:09:21 +0100 Subject: spi: rspi: Do not set SPCR_SPE in qspi_set_config_register() The R-Car Gen2 Hardware User Manual Rev. 2.00 states: If the master/slave mode select bit (MSTR) is modified while the SPI function enable bit (SPE) is set to 1 (that is, this module is enabled), the subsequent operation cannot be guaranteed. Hence do not set SPCR_SPE when setting SPCR_MSTR, just like the .set_config_register() implementations for other RSPI variants do. Note that when booted from QSPI, the boot loader will have set SPCR_MSTR already, hence usually the bit is never modified by the Linux driver. Reported-by: Yoshihiro Shimoda Signed-off-by: Geert Uytterhoeven Signed-off-by: Mark Brown --- drivers/spi/spi-rspi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 2ce875764ca6..0835a8d88fb8 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -377,8 +377,8 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size) /* Sets SPCMD */ rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); - /* Enables SPI function in master mode */ - rspi_write8(rspi, SPCR_SPE | SPCR_MSTR, RSPI_SPCR); + /* Sets RSPI mode */ + rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR); return 0; } -- cgit v1.2.3-59-g8ed1b From c810daba0ab5226084a56893a789af427a801146 Mon Sep 17 00:00:00 2001 From: Takuo Koguchi Date: Thu, 7 Dec 2017 16:20:14 +0900 Subject: spi: sun4i: disable clocks in the remove function mclk and hclk need to be disabled. Since pm_runtime_disable does not disable the clocks, use pm_runtime_force_suspend instead. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Takuo Koguchi Acked-by: Maxime Ripard Signed-off-by: Mark Brown --- drivers/spi/spi-sun4i.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index c5cd635c28f3..41410031f8e9 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -525,7 +525,7 @@ err_free_master: static int sun4i_spi_remove(struct platform_device *pdev) { - pm_runtime_disable(&pdev->dev); + pm_runtime_force_suspend(&pdev->dev); return 0; } -- cgit v1.2.3-59-g8ed1b From 66e900a3d225575c8b48b59ae1fe74bb6e5a65cc Mon Sep 17 00:00:00 2001 From: Radu Pirea Date: Fri, 15 Dec 2017 17:40:17 +0200 Subject: spi: atmel: fixed spin_lock usage inside atmel_spi_remove The only part of atmel_spi_remove which needs to be atomic is hardware reset. atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts enabled. atmel_spi_release_dma calls dma_release_channel and dma_release_channel locks a mutex inside of spin_lock. So the call of these functions can't be inside a spin_lock. Reported-by: Jia-Ju Bai Signed-off-by: Radu Pirea Signed-off-by: Mark Brown --- drivers/spi/spi-atmel.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index f95da364c283..669470971023 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -1661,12 +1661,12 @@ static int atmel_spi_remove(struct platform_device *pdev) pm_runtime_get_sync(&pdev->dev); /* reset the hardware and block queue progress */ - spin_lock_irq(&as->lock); if (as->use_dma) { atmel_spi_stop_dma(master); atmel_spi_release_dma(master); } + spin_lock_irq(&as->lock); spi_writel(as, CR, SPI_BIT(SWRST)); spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */ spi_readl(as, SR); -- cgit v1.2.3-59-g8ed1b