From 93caec0042659bf17ec217b09857bd5eaeca6804 Mon Sep 17 00:00:00 2001 From: Peter De Schrijver Date: Fri, 4 Jan 2019 11:06:43 +0800 Subject: dt-bindings: clock: tegra124-dfll: Update DFLL binding for PWM regulator Add new properties to configure the DFLL PWM regulator support. Cc: devicetree@vger.kernel.org Signed-off-by: Peter De Schrijver Signed-off-by: Joseph Lo Acked-by: Jon Hunter Reviewed-by: Rob Herring Signed-off-by: Thierry Reding --- .../bindings/clock/nvidia,tegra124-dfll.txt | 79 +++++++++++++++++++++- 1 file changed, 77 insertions(+), 2 deletions(-) (limited to 'Documentation/devicetree/bindings/clock') diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index dff236f524a7..5558bb5fcf2c 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -8,7 +8,6 @@ the fast CPU cluster. It consists of a free-running voltage controlled oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop control module that will automatically adjust the VDD_CPU voltage by communicating with an off-chip PMIC either via an I2C bus or via PWM signals. -Currently only the I2C mode is supported by these bindings. Required properties: - compatible : should be "nvidia,tegra124-dfll" @@ -45,10 +44,31 @@ Required properties for the control loop parameters: Optional properties for the control loop parameters: - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM. +Optional properties for mode selection: +- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C. + Required properties for I2C mode: - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode. -Example: +Required properties for PWM mode: +- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds. +- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM + control is disabled and the PWM output is tristated. Note that this voltage is + configured in hardware, typically via a resistor divider. +- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control + is enabled and PWM output is low. Hence, this is the minimum output voltage + that the regulator supports when PWM control is enabled. +- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts + corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th + duty cycle would be: nvidia,pwm-min-microvolts + + nvidia,pwm-voltage-step-microvolts * 2. +- pinctrl-0: I/O pad configuration when PWM control is enabled. +- pinctrl-1: I/O pad configuration when PWM control is disabled. +- pinctrl-names: must include the following entries: + - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled. + - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled. + +Example for I2C: clock@70110000 { compatible = "nvidia,tegra124-dfll"; @@ -76,3 +96,58 @@ clock@70110000 { nvidia,i2c-fs-rate = <400000>; }; + +Example for PWM: + +clock@70110000 { + compatible = "nvidia,tegra124-dfll"; + reg = <0 0x70110000 0 0x100>, /* DFLL control */ + <0 0x70110000 0 0x100>, /* I2C output control */ + <0 0x70110100 0 0x100>, /* Integrated I2C controller */ + <0 0x70110200 0 0x100>; /* Look-up table RAM */ + interrupts = ; + clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>, + <&tegra_car TEGRA210_CLK_DFLL_REF>, + <&tegra_car TEGRA124_CLK_I2C5>;; + clock-names = "soc", "ref", "i2c"; + resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>; + reset-names = "dvco"; + #clock-cells = <0>; + clock-output-names = "dfllCPU_out"; + + nvidia,sample-rate = <25000>; + nvidia,droop-ctrl = <0x00000f00>; + nvidia,force-mode = <1>; + nvidia,cf = <6>; + nvidia,ci = <0>; + nvidia,cg = <2>; + + nvidia,pwm-min-microvolts = <708000>; /* 708mV */ + nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */ + nvidia,pwm-to-pmic; + nvidia,pwm-tristate-microvolts = <1000000>; + nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */ + + pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable"; + pinctrl-0 = <&dvfs_pwm_active_state>; + pinctrl-1 = <&dvfs_pwm_inactive_state>; +}; + +/* pinmux nodes added for completeness. Binding doc can be found in: + * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt + */ + +pinmux: pinmux@700008d4 { + dvfs_pwm_active_state: dvfs_pwm_active { + dvfs_pwm_pbb1 { + nvidia,pins = "dvfs_pwm_pbb1"; + nvidia,tristate = ; + }; + }; + dvfs_pwm_inactive_state: dvfs_pwm_inactive { + dvfs_pwm_pbb1 { + nvidia,pins = "dvfs_pwm_pbb1"; + nvidia,tristate = ; + }; + }; +}; -- cgit v1.2.3-59-g8ed1b From 7e9d10985856dcbcc8f56f97cb103eb3349b3f12 Mon Sep 17 00:00:00 2001 From: Joseph Lo Date: Fri, 4 Jan 2019 11:06:44 +0800 Subject: dt-bindings: clock: tegra124-dfll: add Tegra210 support Add Tegra210 support for DFLL clock. Cc: devicetree@vger.kernel.org Signed-off-by: Joseph Lo Acked-by: Jon Hunter Acked-by: Stephen Boyd Reviewed-by: Rob Herring Signed-off-by: Thierry Reding --- Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'Documentation/devicetree/bindings/clock') diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt index 5558bb5fcf2c..958e0ad78c52 100644 --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -10,7 +10,9 @@ control module that will automatically adjust the VDD_CPU voltage by communicating with an off-chip PMIC either via an I2C bus or via PWM signals. Required properties: -- compatible : should be "nvidia,tegra124-dfll" +- compatible : should be one of: + - "nvidia,tegra124-dfll": for Tegra124 + - "nvidia,tegra210-dfll": for Tegra210 - reg : Defines the following set of registers, in the order listed: - registers for the DFLL control logic. - registers for the I2C output logic. -- cgit v1.2.3-59-g8ed1b