From 24aa40d3c122e57096a314b2503c1e4101f2e84f Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Fri, 25 Sep 2015 23:26:58 -0500 Subject: dt-bindings: consolidate USB PHYs in bindings/phy Move USB PHY bindings under usb directory to phy directory which already contains other USB PHY bindings. The Samsung USB PHY binding is obsolete and can be removed. Signed-off-by: Rob Herring Cc: Pawel Moll Cc: Mark Rutland Cc: Ian Campbell Cc: Kumar Gala --- .../devicetree/bindings/phy/keystone-usb-phy.txt | 20 ++++++ .../devicetree/bindings/phy/mxs-usb-phy.txt | 21 ++++++ .../bindings/phy/nvidia,tegra20-usb-phy.txt | 72 ++++++++++++++++++++ .../devicetree/bindings/phy/qcom,usb-8x16-phy.txt | 76 ++++++++++++++++++++++ 4 files changed, 189 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/keystone-usb-phy.txt create mode 100644 Documentation/devicetree/bindings/phy/mxs-usb-phy.txt create mode 100644 Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt (limited to 'Documentation/devicetree/bindings/phy') diff --git a/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt new file mode 100644 index 000000000000..f37b3a86341d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt @@ -0,0 +1,20 @@ +TI Keystone USB PHY + +Required properties: + - compatible: should be "ti,keystone-usbphy". + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - reg : Address and length of the usb phy control register set. + +The main purpose of this PHY driver is to enable the USB PHY reference clock +gate on the Keystone SOC for both the USB2 and USB3 PHY. Otherwise it is just +an NOP PHY driver. Hence this node is referenced as both the usb2 and usb3 +phy node in the USB Glue layer driver node. + +usb_phy: usb_phy@2620738 { + compatible = "ti,keystone-usbphy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2620738 32>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt new file mode 100644 index 000000000000..379b84a567cc --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mxs-usb-phy.txt @@ -0,0 +1,21 @@ +* Freescale MXS USB Phy Device + +Required properties: +- compatible: should contain: + * "fsl,imx23-usbphy" for imx23 and imx28 + * "fsl,imx6q-usbphy" for imx6dq and imx6dl + * "fsl,imx6sl-usbphy" for imx6sl + * "fsl,vf610-usbphy" for Vybrid vf610 + * "fsl,imx6sx-usbphy" for imx6sx + "fsl,imx23-usbphy" is still a fallback for other strings +- reg: Should contain registers location and length +- interrupts: Should contain phy interrupt +- fsl,anatop: phandle for anatop register, it is only for imx6 SoC series + +Example: +usbphy1: usbphy@020c9000 { + compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; + reg = <0x020c9000 0x1000>; + interrupts = <0 44 0x04>; + fsl,anatop = <&anatop>; +}; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt new file mode 100644 index 000000000000..a9aa79fb90ed --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.txt @@ -0,0 +1,72 @@ +Tegra SOC USB PHY + +The device node for Tegra SOC USB PHY: + +Required properties : + - compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy". + For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain + "nvidia,-usb-phy" plus at least one of the above, where is + tegra114, tegra124, tegra132, or tegra210. + - reg : Defines the following set of registers, in the order listed: + - The PHY's own register set. + Always present. + - The register set of the PHY containing the UTMI pad control registers. + Present if-and-only-if phy_type == utmi. + - phy_type : Should be one of "utmi", "ulpi" or "hsic". + - clocks : Defines the clocks listed in the clock-names property. + - clock-names : The following clock names must be present: + - reg: The clock needed to access the PHY's own registers. This is the + associated EHCI controller's clock. Always present. + - pll_u: PLL_U. Always present. + - timer: The timeout clock (clk_m). Present if phy_type == utmi. + - utmi-pads: The clock needed to access the UTMI pad control registers. + Present if phy_type == utmi. + - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2). + Present if phy_type == ulpi, and ULPI link mode is in use. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Must include the following entries: + - usb: The PHY's own reset signal. + - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control + registers. Required even if phy_type == ulpi. + +Required properties for phy_type == ulpi: + - nvidia,phy-reset-gpio : The GPIO used to reset the PHY. + +Required PHY timing params for utmi phy, for all chips: + - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before + start of sync launches RxActive + - nvidia,elastic-limit : Variable FIFO Depth of elastic input store + - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait + before declare IDLE. + - nvidia,term-range-adj : Range adjusment on terminations + - Either one of the following for HS driver output control: + - nvidia,xcvr-setup : integer, uses the provided value. + - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read + from the on-chip fuses + If both are provided, nvidia,xcvr-setup-use-fuses takes precedence. + - nvidia,xcvr-lsfslew : LS falling slew rate control. + - nvidia,xcvr-lsrslew : LS rising slew rate control. + +Required PHY timing params for utmi phy, only on Tegra30 and above: + - nvidia,xcvr-hsslew : HS slew rate control. + - nvidia,hssquelch-level : HS squelch detector level. + - nvidia,hsdiscon-level : HS disconnect detector level. + +Optional properties: + - nvidia,has-legacy-mode : boolean indicates whether this controller can + operate in legacy mode (as APX 2500 / 2600). In legacy mode some + registers are accessed through the APB_MISC base address instead of + the USB controller. + - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power + optimizations for the devices that are always connected. e.g. modem. + - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be + "host", "peripheral", or "otg". Defaults to "host" if not defined. + host means this is a host controller + peripheral means it is device controller + otg means it can operate as either ("on the go") + - nvidia,has-utmi-pad-registers : boolean indicates whether this controller + contains the UTMI pad control registers common to all USB controllers. + +VBUS control (required for dr_mode == otg, optional for dr_mode == host): + - vbus-supply: regulator for VBUS diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt new file mode 100644 index 000000000000..2cb2168cef41 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt @@ -0,0 +1,76 @@ +Qualcomm's APQ8016/MSM8916 USB transceiver controller + +- compatible: + Usage: required + Value type: + Definition: Should contain "qcom,usb-8x16-phy". + +- reg: + Usage: required + Value type: + Definition: USB PHY base address and length of the register map + +- clocks: + Usage: required + Value type: + Definition: See clock-bindings.txt section "consumers". List of + two clock specifiers for interface and core controller + clocks. + +- clock-names: + Usage: required + Value type: + Definition: Must contain "iface" and "core" strings. + +- vddcx-supply: + Usage: required + Value type: + Definition: phandle to the regulator VDCCX supply node. + +- v1p8-supply: + Usage: required + Value type: + Definition: phandle to the regulator 1.8V supply node. + +- v3p3-supply: + Usage: required + Value type: + Definition: phandle to the regulator 3.3V supply node. + +- resets: + Usage: required + Value type: + Definition: See reset.txt section "consumers". PHY reset specifier. + +- reset-names: + Usage: required + Value type: + Definition: Must contain "phy" string. + +- switch-gpio: + Usage: optional + Value type: + Definition: Some boards are using Dual SPDT USB Switch, witch is + controlled by GPIO to de/multiplex D+/D- USB lines + between connectors. + +Example: + usb_phy: phy@78d9000 { + compatible = "qcom,usb-8x16-phy"; + reg = <0x78d9000 0x400>; + + vddcx-supply = <&pm8916_s1_corner>; + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + + clocks = <&gcc GCC_USB_HS_AHB_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + + resets = <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy"; + + // D+/D- lines: 1 - Routed to HUB, 0 - Device connector + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + }; + -- cgit v1.2.3-59-g8ed1b