From 5e07321f3388e6f2b13c43ae9df3e09efa8418e0 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Fri, 22 Mar 2019 01:05:01 +0100 Subject: dt-bindings: net: dsa: qca8k: support internal mdio-bus This patch updates the qca8k's binding to document to the approach for using the internal mdio-bus of the supported qca8k switches. Reviewed-by: Florian Fainelli Signed-off-by: Christian Lamparter Signed-off-by: David S. Miller --- .../devicetree/bindings/net/dsa/qca8k.txt | 69 ++++++++++++++++++++-- 1 file changed, 64 insertions(+), 5 deletions(-) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index 5eda99e6c86e..93a7469e70d4 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -12,10 +12,15 @@ Required properties: Subnodes: The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of -port and PHY id, each subnode describing a port needs to have a valid phandle -referencing the internal PHY connected to it. The CPU port of this switch is -always port 0. +described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +mdio-bus each subnode describing a port needs to have a valid phandle +referencing the internal PHY it is connected to. This is because there's no +N:N mapping of port and PHY id. + +Don't use mixed external and internal mdio-bus configurations, as this is +not supported by the hardware. + +The CPU port of this switch is always port 0. A CPU port node has the following optional node: @@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties: - 'full-duplex' (boolean, optional), to indicate that full duplex is used. When absent, half duplex is assumed. -Example: +Examples: +for the external mdio-bus configuration: &mdio0 { phy_port1: phy@0 { @@ -108,3 +114,56 @@ Example: }; }; }; + +for the internal master mdio-bus configuration: + + &mdio0 { + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + }; + }; + }; -- cgit v1.2.3-59-g8ed1b