From 77fe661214d784878d666a226116057191de097b Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Fri, 3 Nov 2017 10:19:38 +0530 Subject: dmaengine: doc: ReSTize provider doc This moves and converts provider file with some format changes for RST style Signed-off-by: Vinod Koul Signed-off-by: Jonathan Corbet --- Documentation/dmaengine/provider.txt | 424 ----------------------------------- 1 file changed, 424 deletions(-) delete mode 100644 Documentation/dmaengine/provider.txt (limited to 'Documentation/dmaengine/provider.txt') diff --git a/Documentation/dmaengine/provider.txt b/Documentation/dmaengine/provider.txt deleted file mode 100644 index 5dbe054a40ad..000000000000 --- a/Documentation/dmaengine/provider.txt +++ /dev/null @@ -1,424 +0,0 @@ -DMAengine controller documentation -================================== - -Hardware Introduction -+++++++++++++++++++++ - -Most of the Slave DMA controllers have the same general principles of -operations. - -They have a given number of channels to use for the DMA transfers, and -a given number of requests lines. - -Requests and channels are pretty much orthogonal. Channels can be used -to serve several to any requests. To simplify, channels are the -entities that will be doing the copy, and requests what endpoints are -involved. - -The request lines actually correspond to physical lines going from the -DMA-eligible devices to the controller itself. Whenever the device -will want to start a transfer, it will assert a DMA request (DRQ) by -asserting that request line. - -A very simple DMA controller would only take into account a single -parameter: the transfer size. At each clock cycle, it would transfer a -byte of data from one buffer to another, until the transfer size has -been reached. - -That wouldn't work well in the real world, since slave devices might -require a specific number of bits to be transferred in a single -cycle. For example, we may want to transfer as much data as the -physical bus allows to maximize performances when doing a simple -memory copy operation, but our audio device could have a narrower FIFO -that requires data to be written exactly 16 or 24 bits at a time. This -is why most if not all of the DMA controllers can adjust this, using a -parameter called the transfer width. - -Moreover, some DMA controllers, whenever the RAM is used as a source -or destination, can group the reads or writes in memory into a buffer, -so instead of having a lot of small memory accesses, which is not -really efficient, you'll get several bigger transfers. This is done -using a parameter called the burst size, that defines how many single -reads/writes it's allowed to do without the controller splitting the -transfer into smaller sub-transfers. - -Our theoretical DMA controller would then only be able to do transfers -that involve a single contiguous block of data. However, some of the -transfers we usually have are not, and want to copy data from -non-contiguous buffers to a contiguous buffer, which is called -scatter-gather. - -DMAEngine, at least for mem2dev transfers, require support for -scatter-gather. So we're left with two cases here: either we have a -quite simple DMA controller that doesn't support it, and we'll have to -implement it in software, or we have a more advanced DMA controller, -that implements in hardware scatter-gather. - -The latter are usually programmed using a collection of chunks to -transfer, and whenever the transfer is started, the controller will go -over that collection, doing whatever we programmed there. - -This collection is usually either a table or a linked list. You will -then push either the address of the table and its number of elements, -or the first item of the list to one channel of the DMA controller, -and whenever a DRQ will be asserted, it will go through the collection -to know where to fetch the data from. - -Either way, the format of this collection is completely dependent on -your hardware. Each DMA controller will require a different structure, -but all of them will require, for every chunk, at least the source and -destination addresses, whether it should increment these addresses or -not and the three parameters we saw earlier: the burst size, the -transfer width and the transfer size. - -The one last thing is that usually, slave devices won't issue DRQ by -default, and you have to enable this in your slave device driver first -whenever you're willing to use DMA. - -These were just the general memory-to-memory (also called mem2mem) or -memory-to-device (mem2dev) kind of transfers. Most devices often -support other kind of transfers or memory operations that dmaengine -support and will be detailed later in this document. - -DMA Support in Linux -++++++++++++++++++++ - -Historically, DMA controller drivers have been implemented using the -async TX API, to offload operations such as memory copy, XOR, -cryptography, etc., basically any memory to memory operation. - -Over time, the need for memory to device transfers arose, and -dmaengine was extended. Nowadays, the async TX API is written as a -layer on top of dmaengine, and acts as a client. Still, dmaengine -accommodates that API in some cases, and made some design choices to -ensure that it stayed compatible. - -For more information on the Async TX API, please look the relevant -documentation file in Documentation/crypto/async-tx-api.txt. - -DMAEngine Registration -++++++++++++++++++++++ - -struct dma_device Initialization --------------------------------- - -Just like any other kernel framework, the whole DMAEngine registration -relies on the driver filling a structure and registering against the -framework. In our case, that structure is dma_device. - -The first thing you need to do in your driver is to allocate this -structure. Any of the usual memory allocators will do, but you'll also -need to initialize a few fields in there: - - * channels: should be initialized as a list using the - INIT_LIST_HEAD macro for example - - * src_addr_widths: - - should contain a bitmask of the supported source transfer width - - * dst_addr_widths: - - should contain a bitmask of the supported destination transfer - width - - * directions: - - should contain a bitmask of the supported slave directions - (i.e. excluding mem2mem transfers) - - * residue_granularity: - - Granularity of the transfer residue reported to dma_set_residue. - - This can be either: - + Descriptor - -> Your device doesn't support any kind of residue - reporting. The framework will only know that a particular - transaction descriptor is done. - + Segment - -> Your device is able to report which chunks have been - transferred - + Burst - -> Your device is able to report which burst have been - transferred - - * dev: should hold the pointer to the struct device associated - to your current driver instance. - -Supported transaction types ---------------------------- - -The next thing you need is to set which transaction types your device -(and driver) supports. - -Our dma_device structure has a field called cap_mask that holds the -various types of transaction supported, and you need to modify this -mask using the dma_cap_set function, with various flags depending on -transaction types you support as an argument. - -All those capabilities are defined in the dma_transaction_type enum, -in include/linux/dmaengine.h - -Currently, the types available are: - * DMA_MEMCPY - - The device is able to do memory to memory copies - - * DMA_XOR - - The device is able to perform XOR operations on memory areas - - Used to accelerate XOR intensive tasks, such as RAID5 - - * DMA_XOR_VAL - - The device is able to perform parity check using the XOR - algorithm against a memory buffer. - - * DMA_PQ - - The device is able to perform RAID6 P+Q computations, P being a - simple XOR, and Q being a Reed-Solomon algorithm. - - * DMA_PQ_VAL - - The device is able to perform parity check using RAID6 P+Q - algorithm against a memory buffer. - - * DMA_INTERRUPT - - The device is able to trigger a dummy transfer that will - generate periodic interrupts - - Used by the client drivers to register a callback that will be - called on a regular basis through the DMA controller interrupt - - * DMA_PRIVATE - - The devices only supports slave transfers, and as such isn't - available for async transfers. - - * DMA_ASYNC_TX - - Must not be set by the device, and will be set by the framework - if needed - - /* TODO: What is it about? */ - - * DMA_SLAVE - - The device can handle device to memory transfers, including - scatter-gather transfers. - - While in the mem2mem case we were having two distinct types to - deal with a single chunk to copy or a collection of them, here, - we just have a single transaction type that is supposed to - handle both. - - If you want to transfer a single contiguous memory buffer, - simply build a scatter list with only one item. - - * DMA_CYCLIC - - The device can handle cyclic transfers. - - A cyclic transfer is a transfer where the chunk collection will - loop over itself, with the last item pointing to the first. - - It's usually used for audio transfers, where you want to operate - on a single ring buffer that you will fill with your audio data. - - * DMA_INTERLEAVE - - The device supports interleaved transfer. - - These transfers can transfer data from a non-contiguous buffer - to a non-contiguous buffer, opposed to DMA_SLAVE that can - transfer data from a non-contiguous data set to a continuous - destination buffer. - - It's usually used for 2d content transfers, in which case you - want to transfer a portion of uncompressed data directly to the - display to print it - -These various types will also affect how the source and destination -addresses change over time. - -Addresses pointing to RAM are typically incremented (or decremented) -after each transfer. In case of a ring buffer, they may loop -(DMA_CYCLIC). Addresses pointing to a device's register (e.g. a FIFO) -are typically fixed. - -Device operations ------------------ - -Our dma_device structure also requires a few function pointers in -order to implement the actual logic, now that we described what -operations we were able to perform. - -The functions that we have to fill in there, and hence have to -implement, obviously depend on the transaction types you reported as -supported. - - * device_alloc_chan_resources - * device_free_chan_resources - - These functions will be called whenever a driver will call - dma_request_channel or dma_release_channel for the first/last - time on the channel associated to that driver. - - They are in charge of allocating/freeing all the needed - resources in order for that channel to be useful for your - driver. - - These functions can sleep. - - * device_prep_dma_* - - These functions are matching the capabilities you registered - previously. - - These functions all take the buffer or the scatterlist relevant - for the transfer being prepared, and should create a hardware - descriptor or a list of hardware descriptors from it - - These functions can be called from an interrupt context - - Any allocation you might do should be using the GFP_NOWAIT - flag, in order not to potentially sleep, but without depleting - the emergency pool either. - - Drivers should try to pre-allocate any memory they might need - during the transfer setup at probe time to avoid putting to - much pressure on the nowait allocator. - - - It should return a unique instance of the - dma_async_tx_descriptor structure, that further represents this - particular transfer. - - - This structure can be initialized using the function - dma_async_tx_descriptor_init. - - You'll also need to set two fields in this structure: - + flags: - TODO: Can it be modified by the driver itself, or - should it be always the flags passed in the arguments - - + tx_submit: A pointer to a function you have to implement, - that is supposed to push the current - transaction descriptor to a pending queue, waiting - for issue_pending to be called. - - In this structure the function pointer callback_result can be - initialized in order for the submitter to be notified that a - transaction has completed. In the earlier code the function pointer - callback has been used. However it does not provide any status to the - transaction and will be deprecated. The result structure defined as - dmaengine_result that is passed in to callback_result has two fields: - + result: This provides the transfer result defined by - dmaengine_tx_result. Either success or some error - condition. - + residue: Provides the residue bytes of the transfer for those that - support residue. - - * device_issue_pending - - Takes the first transaction descriptor in the pending queue, - and starts the transfer. Whenever that transfer is done, it - should move to the next transaction in the list. - - This function can be called in an interrupt context - - * device_tx_status - - Should report the bytes left to go over on the given channel - - Should only care about the transaction descriptor passed as - argument, not the currently active one on a given channel - - The tx_state argument might be NULL - - Should use dma_set_residue to report it - - In the case of a cyclic transfer, it should only take into - account the current period. - - This function can be called in an interrupt context. - - * device_config - - Reconfigures the channel with the configuration given as - argument - - This command should NOT perform synchronously, or on any - currently queued transfers, but only on subsequent ones - - In this case, the function will receive a dma_slave_config - structure pointer as an argument, that will detail which - configuration to use. - - Even though that structure contains a direction field, this - field is deprecated in favor of the direction argument given to - the prep_* functions - - This call is mandatory for slave operations only. This should NOT be - set or expected to be set for memcpy operations. - If a driver support both, it should use this call for slave - operations only and not for memcpy ones. - - * device_pause - - Pauses a transfer on the channel - - This command should operate synchronously on the channel, - pausing right away the work of the given channel - - * device_resume - - Resumes a transfer on the channel - - This command should operate synchronously on the channel, - resuming right away the work of the given channel - - * device_terminate_all - - Aborts all the pending and ongoing transfers on the channel - - For aborted transfers the complete callback should not be called - - Can be called from atomic context or from within a complete - callback of a descriptor. Must not sleep. Drivers must be able - to handle this correctly. - - Termination may be asynchronous. The driver does not have to - wait until the currently active transfer has completely stopped. - See device_synchronize. - - * device_synchronize - - Must synchronize the termination of a channel to the current - context. - - Must make sure that memory for previously submitted - descriptors is no longer accessed by the DMA controller. - - Must make sure that all complete callbacks for previously - submitted descriptors have finished running and none are - scheduled to run. - - May sleep. - - -Misc notes (stuff that should be documented, but don't really know -where to put them) ------------------------------------------------------------------- - * dma_run_dependencies - - Should be called at the end of an async TX transfer, and can be - ignored in the slave transfers case. - - Makes sure that dependent operations are run before marking it - as complete. - - * dma_cookie_t - - it's a DMA transaction ID that will increment over time. - - Not really relevant any more since the introduction of virt-dma - that abstracts it away. - - * DMA_CTRL_ACK - - If clear, the descriptor cannot be reused by provider until the - client acknowledges receipt, i.e. has has a chance to establish any - dependency chains - - This can be acked by invoking async_tx_ack() - - If set, does not mean descriptor can be reused - - * DMA_CTRL_REUSE - - If set, the descriptor can be reused after being completed. It should - not be freed by provider if this flag is set. - - The descriptor should be prepared for reuse by invoking - dmaengine_desc_set_reuse() which will set DMA_CTRL_REUSE. - - dmaengine_desc_set_reuse() will succeed only when channel support - reusable descriptor as exhibited by capabilities - - As a consequence, if a device driver wants to skip the dma_map_sg() and - dma_unmap_sg() in between 2 transfers, because the DMA'd data wasn't used, - it can resubmit the transfer right after its completion. - - Descriptor can be freed in few ways - - Clearing DMA_CTRL_REUSE by invoking dmaengine_desc_clear_reuse() - and submitting for last txn - - Explicitly invoking dmaengine_desc_free(), this can succeed only - when DMA_CTRL_REUSE is already set - - Terminating the channel - - * DMA_PREP_CMD - - If set, the client driver tells DMA controller that passed data in DMA - API is command data. - - Interpretation of command data is DMA controller specific. It can be - used for issuing commands to other peripherals/register reads/register - writes for which the descriptor should be in different format from - normal data descriptors. - -General Design Notes --------------------- - -Most of the DMAEngine drivers you'll see are based on a similar design -that handles the end of transfer interrupts in the handler, but defer -most work to a tasklet, including the start of a new transfer whenever -the previous transfer ended. - -This is a rather inefficient design though, because the inter-transfer -latency will be not only the interrupt latency, but also the -scheduling latency of the tasklet, which will leave the channel idle -in between, which will slow down the global transfer rate. - -You should avoid this kind of practice, and instead of electing a new -transfer in your tasklet, move that part to the interrupt handler in -order to have a shorter idle window (that we can't really avoid -anyway). - -Glossary --------- - -Burst: A number of consecutive read or write operations - that can be queued to buffers before being flushed to - memory. -Chunk: A contiguous collection of bursts -Transfer: A collection of chunks (be it contiguous or not) -- cgit v1.2.3-59-g8ed1b