From 455716e9b12ba93e93181ac88bef62e4eb5ac66c Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 1 Jul 2011 22:29:05 +0200 Subject: PM / Runtime: Update documentation of interactions with system sleep The documents describing the interactions between runtime PM and system sleep generally refer to the model in which the system sleep state is entered through a global firmware or hardware operation. As a result, some recommendations given in there are not entirely suitable for systems in which this is not the case. Update the documentation to take the existence of those systems into account. Signed-off-by: Rafael J. Wysocki Reviewed-by: Kevin Hilman --- Documentation/power/devices.txt | 6 +++--- Documentation/power/runtime_pm.txt | 27 +++++++++++++++++++-------- 2 files changed, 22 insertions(+), 11 deletions(-) (limited to 'Documentation/power') diff --git a/Documentation/power/devices.txt b/Documentation/power/devices.txt index 85c6f980b642..3384d5996be2 100644 --- a/Documentation/power/devices.txt +++ b/Documentation/power/devices.txt @@ -604,7 +604,7 @@ state temporarily, for example so that its system wakeup capability can be disabled. This all depends on the hardware and the design of the subsystem and device driver in question. -During system-wide resume from a sleep state it's best to put devices into the -full-power state, as explained in Documentation/power/runtime_pm.txt. Refer to -that document for more information regarding this particular issue as well as +During system-wide resume from a sleep state it's easiest to put devices into +the full-power state, as explained in Documentation/power/runtime_pm.txt. Refer +to that document for more information regarding this particular issue as well as for information on the device runtime power management framework in general. diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 4b011b171be4..513c52ef5a42 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -553,9 +553,9 @@ suspend routine). It may be necessary to resume the device and suspend it again in order to do so. The same is true if the driver uses different power levels or other settings for run-time suspend and system sleep. -During system resume, devices generally should be brought back to full power, -even if they were suspended before the system sleep began. There are several -reasons for this, including: +During system resume, the simplest approach is to bring all devices back to full +power, even if they had been suspended before the system suspend began. There +are several reasons for this, including: * The device might need to switch power levels, wake-up settings, etc. @@ -572,16 +572,27 @@ reasons for this, including: * Even though the device was suspended, if its usage counter was > 0 then most likely it would need a run-time resume in the near future anyway. - * Always going back to full power is simplest. - -If the device was suspended before the sleep began, then its run-time PM status -will have to be updated to reflect the actual post-system sleep status. The way -to do this is: +If the device had been suspended before the system suspend began and it's +brought back to full power during resume, then its run-time PM status will have +to be updated to reflect the actual post-system sleep status. The way to do +this is: pm_runtime_disable(dev); pm_runtime_set_active(dev); pm_runtime_enable(dev); +On some systems, however, system sleep is not entered through a global firmware +or hardware operation. Instead, all hardware components are put into low-power +states directly by the kernel in a coordinated way. Then, the system sleep +state effectively follows from the states the hardware components end up in +and the system is woken up from that state by a hardware interrupt or a similar +mechanism entirely under the kernel's control. As a result, the kernel never +gives control away and the states of all devices during resume are precisely +known to it. If that is the case and none of the situations listed above takes +place (in particular, if the system is not waking up from hibernation), it may +be more efficient to leave the devices that had been suspended before the system +suspend began in the suspended state. + 7. Generic subsystem callbacks Subsystems may wish to conserve code space by using the set of generic power -- cgit v1.2.3-59-g8ed1b From 632e270e01d8a1ee9e8ea56c83028727f17b1d17 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Fri, 1 Jul 2011 22:29:15 +0200 Subject: PM / Runtime: Return special error code if runtime PM is disabled Some callers of pm_runtime_get_sync() and other runtime PM helper functions, scsi_autopm_get_host() and scsi_autopm_get_device() in particular, need to distinguish error codes returned when runtime PM is disabled (i.e. power.disable_depth is nonzero for the given device) from error codes returned in other situations. For this reason, make the runtime PM helper functions return -EACCES when power.disable_depth is nonzero and ensure that this error code won't be returned by them in any other circumstances. Modify scsi_autopm_get_host() and scsi_autopm_get_device() to check the error code returned by pm_runtime_get_sync() and ignore -EACCES. Signed-off-by: Rafael J. Wysocki --- Documentation/power/runtime_pm.txt | 6 ++++-- drivers/base/power/runtime.c | 9 +++++---- drivers/scsi/scsi_pm.c | 8 ++++---- 3 files changed, 13 insertions(+), 10 deletions(-) (limited to 'Documentation/power') diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 513c52ef5a42..0ec3d610fc9a 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -291,7 +291,8 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: - execute the subsystem-level suspend callback for the device; returns 0 on success, 1 if the device's run-time PM status was already 'suspended', or error code on failure, where -EAGAIN or -EBUSY means it is safe to attempt - to suspend the device again in future + to suspend the device again in future and -EACCES means that + 'power.disable_depth' is different from 0 int pm_runtime_autosuspend(struct device *dev); - same as pm_runtime_suspend() except that the autosuspend delay is taken @@ -304,7 +305,8 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: success, 1 if the device's run-time PM status was already 'active' or error code on failure, where -EAGAIN means it may be safe to attempt to resume the device again in future, but 'power.runtime_error' should be - checked additionally + checked additionally, and -EACCES means that 'power.disable_depth' is + different from 0 int pm_request_idle(struct device *dev); - submit a request to execute the subsystem-level idle callback for the diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c index 5f5c4236f006..ee99025be6b3 100644 --- a/drivers/base/power/runtime.c +++ b/drivers/base/power/runtime.c @@ -135,8 +135,9 @@ static int rpm_check_suspend_allowed(struct device *dev) if (dev->power.runtime_error) retval = -EINVAL; - else if (atomic_read(&dev->power.usage_count) > 0 - || dev->power.disable_depth > 0) + else if (dev->power.disable_depth > 0) + retval = -EACCES; + else if (atomic_read(&dev->power.usage_count) > 0) retval = -EAGAIN; else if (!pm_children_suspended(dev)) retval = -EBUSY; @@ -262,7 +263,7 @@ static int rpm_callback(int (*cb)(struct device *), struct device *dev) spin_lock_irq(&dev->power.lock); } dev->power.runtime_error = retval; - return retval; + return retval != -EACCES ? retval : -EIO; } /** @@ -458,7 +459,7 @@ static int rpm_resume(struct device *dev, int rpmflags) if (dev->power.runtime_error) retval = -EINVAL; else if (dev->power.disable_depth > 0) - retval = -EAGAIN; + retval = -EACCES; if (retval) goto out; diff --git a/drivers/scsi/scsi_pm.c b/drivers/scsi/scsi_pm.c index d70e91ae60af..d82a023a9015 100644 --- a/drivers/scsi/scsi_pm.c +++ b/drivers/scsi/scsi_pm.c @@ -144,9 +144,9 @@ int scsi_autopm_get_device(struct scsi_device *sdev) int err; err = pm_runtime_get_sync(&sdev->sdev_gendev); - if (err < 0) + if (err < 0 && err !=-EACCES) pm_runtime_put_sync(&sdev->sdev_gendev); - else if (err > 0) + else err = 0; return err; } @@ -173,9 +173,9 @@ int scsi_autopm_get_host(struct Scsi_Host *shost) int err; err = pm_runtime_get_sync(&shost->shost_gendev); - if (err < 0) + if (err < 0 && err !=-EACCES) pm_runtime_put_sync(&shost->shost_gendev); - else if (err > 0) + else err = 0; return err; } -- cgit v1.2.3-59-g8ed1b From 1e2ef05bb8cf851a694d38e9170c89e7ff052741 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 6 Jul 2011 10:51:58 +0200 Subject: PM: Limit race conditions between runtime PM and system sleep (v2) One of the roles of the PM core is to prevent different PM callbacks executed for the same device object from racing with each other. Unfortunately, after commit e8665002477f0278f84f898145b1f141ba26ee26 (PM: Allow pm_runtime_suspend() to succeed during system suspend) runtime PM callbacks may be executed concurrently with system suspend/resume callbacks for the same device. The main reason for commit e8665002477f0278f84f898145b1f141ba26ee26 was that some subsystems and device drivers wanted to use runtime PM helpers, pm_runtime_suspend() and pm_runtime_put_sync() in particular, for carrying out the suspend of devices in their .suspend() callbacks. However, as it's been determined recently, there are multiple reasons not to do so, inlcuding: * The caller really doesn't control the runtime PM usage counters, because user space can access them through sysfs and effectively block runtime PM. That means using pm_runtime_suspend() or pm_runtime_get_sync() to suspend devices during system suspend may or may not work. * If a driver calls pm_runtime_suspend() from its .suspend() callback, it causes the subsystem's .runtime_suspend() callback to be executed, which leads to the call sequence: subsys->suspend(dev) driver->suspend(dev) pm_runtime_suspend(dev) subsys->runtime_suspend(dev) recursive from the subsystem's point of view. For some subsystems that may actually work (e.g. the platform bus type), but for some it will fail in a rather spectacular fashion (e.g. PCI). In each case it means a layering violation. * Both the subsystem and the driver can provide .suspend_noirq() callbacks for system suspend that can do whatever the .runtime_suspend() callbacks do just fine, so it really isn't necessary to call pm_runtime_suspend() during system suspend. * The runtime PM's handling of wakeup devices is usually different from the system suspend's one, so .runtime_suspend() may simply be inappropriate for system suspend. * System suspend is supposed to work even if CONFIG_PM_RUNTIME is unset. * The runtime PM workqueue is frozen before system suspend, so if whatever the driver is going to do during system suspend depends on it, that simply won't work. Still, there is a good reason to allow pm_runtime_resume() to succeed during system suspend and resume (for instance, some subsystems and device drivers may legitimately use it to ensure that their devices are in full-power states before suspending them). Moreover, there is no reason to prevent runtime PM callbacks from being executed in parallel with the system suspend/resume .prepare() and .complete() callbacks and the code removed by commit e8665002477f0278f84f898145b1f141ba26ee26 went too far in this respect. On the other hand, runtime PM callbacks, including .runtime_resume(), must not be executed during system suspend's "late" stage of suspending devices and during system resume's "early" device resume stage. Taking all of the above into consideration, make the PM core acquire a runtime PM reference to every device and resume it if there's a runtime PM resume request pending right before executing the subsystem-level .suspend() callback for it. Make the PM core drop references to all devices right after executing the subsystem-level .resume() callbacks for them. Additionally, make the PM core disable the runtime PM framework for all devices during system suspend, after executing the subsystem-level .suspend() callbacks for them, and enable the runtime PM framework for all devices during system resume, right before executing the subsystem-level .resume() callbacks for them. Signed-off-by: Rafael J. Wysocki Acked-by: Kevin Hilman --- Documentation/power/runtime_pm.txt | 21 +++++++++++++++++++++ drivers/base/power/main.c | 35 +++++++++++++++++++++++------------ 2 files changed, 44 insertions(+), 12 deletions(-) (limited to 'Documentation/power') diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 0ec3d610fc9a..d50dd1ab590d 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -583,6 +583,13 @@ this is: pm_runtime_set_active(dev); pm_runtime_enable(dev); +The PM core always increments the run-time usage counter before calling the +->suspend() callback and decrements it after calling the ->resume() callback. +Hence disabling run-time PM temporarily like this will not cause any runtime +suspend attempts to be permanently lost. If the usage count goes to zero +following the return of the ->resume() callback, the ->runtime_idle() callback +will be invoked as usual. + On some systems, however, system sleep is not entered through a global firmware or hardware operation. Instead, all hardware components are put into low-power states directly by the kernel in a coordinated way. Then, the system sleep @@ -595,6 +602,20 @@ place (in particular, if the system is not waking up from hibernation), it may be more efficient to leave the devices that had been suspended before the system suspend began in the suspended state. +The PM core does its best to reduce the probability of race conditions between +the runtime PM and system suspend/resume (and hibernation) callbacks by carrying +out the following operations: + + * During system suspend it calls pm_runtime_get_noresume() and + pm_runtime_barrier() for every device right before executing the + subsystem-level .suspend() callback for it. In addition to that it calls + pm_runtime_disable() for every device right after executing the + subsystem-level .suspend() callback for it. + + * During system resume it calls pm_runtime_enable() and pm_runtime_put_sync() + for every device right before and right after executing the subsystem-level + .resume() callback for it, respectively. + 7. Generic subsystem callbacks Subsystems may wish to conserve code space by using the set of generic power diff --git a/drivers/base/power/main.c b/drivers/base/power/main.c index 85b591a5429a..a85459126bc6 100644 --- a/drivers/base/power/main.c +++ b/drivers/base/power/main.c @@ -505,6 +505,7 @@ static int legacy_resume(struct device *dev, int (*cb)(struct device *dev)) static int device_resume(struct device *dev, pm_message_t state, bool async) { int error = 0; + bool put = false; TRACE_DEVICE(dev); TRACE_RESUME(0); @@ -521,6 +522,9 @@ static int device_resume(struct device *dev, pm_message_t state, bool async) if (!dev->power.is_suspended) goto Unlock; + pm_runtime_enable(dev); + put = true; + if (dev->pm_domain) { pm_dev_dbg(dev, state, "power domain "); error = pm_op(dev, &dev->pm_domain->ops, state); @@ -563,6 +567,10 @@ static int device_resume(struct device *dev, pm_message_t state, bool async) complete_all(&dev->power.completion); TRACE_RESUME(error); + + if (put) + pm_runtime_put_sync(dev); + return error; } @@ -843,16 +851,22 @@ static int __device_suspend(struct device *dev, pm_message_t state, bool async) int error = 0; dpm_wait_for_children(dev, async); - device_lock(dev); if (async_error) - goto Unlock; + return 0; + + pm_runtime_get_noresume(dev); + if (pm_runtime_barrier(dev) && device_may_wakeup(dev)) + pm_wakeup_event(dev, 0); if (pm_wakeup_pending()) { + pm_runtime_put_sync(dev); async_error = -EBUSY; - goto Unlock; + return 0; } + device_lock(dev); + if (dev->pm_domain) { pm_dev_dbg(dev, state, "power domain "); error = pm_op(dev, &dev->pm_domain->ops, state); @@ -890,12 +904,15 @@ static int __device_suspend(struct device *dev, pm_message_t state, bool async) End: dev->power.is_suspended = !error; - Unlock: device_unlock(dev); complete_all(&dev->power.completion); - if (error) + if (error) { + pm_runtime_put_sync(dev); async_error = error; + } else if (dev->power.is_suspended) { + __pm_runtime_disable(dev, false); + } return error; } @@ -1035,13 +1052,7 @@ int dpm_prepare(pm_message_t state) get_device(dev); mutex_unlock(&dpm_list_mtx); - pm_runtime_get_noresume(dev); - if (pm_runtime_barrier(dev) && device_may_wakeup(dev)) - pm_wakeup_event(dev, 0); - - pm_runtime_put_sync(dev); - error = pm_wakeup_pending() ? - -EBUSY : device_prepare(dev, state); + error = device_prepare(dev, state); mutex_lock(&dpm_list_mtx); if (error) { -- cgit v1.2.3-59-g8ed1b From e358bad75ff13210f5211cac9f93d76170d43f89 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 6 Jul 2011 10:52:06 +0200 Subject: PM / Runtime: Improve documentation of enable, disable and barrier The runtime PM documentation in Documentation/power/runtime_pm.txt doesn't say that pm_runtime_enable() and pm_runtime_disable() work by operating on power.disable_depth, which is wrong, because the possibility of nesting disables doesn't follow from the description of these functions. Also, there is no description of pm_runtime_barrier() at all in the document, which is confusing. Improve the documentation by fixing those issues. Signed-off-by: Rafael J. Wysocki --- Documentation/power/runtime_pm.txt | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-) (limited to 'Documentation/power') diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index d50dd1ab590d..ca15bbbe1891 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -369,17 +369,27 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: pm_runtime_autosuspend(dev) and return its result void pm_runtime_enable(struct device *dev); - - enable the run-time PM helper functions to run the device bus type's - run-time PM callbacks described in Section 2 + - decrement the device's 'power.disable_depth' field; if that field is equal + to zero, the run-time PM helper functions can execute subsystem-level + callbacks described in Section 2 for the device int pm_runtime_disable(struct device *dev); - - prevent the run-time PM helper functions from running subsystem-level - run-time PM callbacks for the device, make sure that all of the pending + - increment the device's 'power.disable_depth' field (if the value of that + field was previously zero, this prevents subsystem-level runtime PM + callbacks from being run for the device), make sure that all of the pending run-time PM operations on the device are either completed or canceled; returns 1 if there was a resume request pending and it was necessary to execute the subsystem-level resume callback for the device to satisfy that request, otherwise 0 is returned + int pm_runtime_barrier(struct device *dev); + - check if there's a resume request pending for the device and resume it + (synchronously) in that case, cancel any other pending runtime PM requests + regarding it and wait for all runtime PM operations on it in progress to + complete; returns 1 if there was a resume request pending and it was + necessary to execute the subsystem-level resume callback for the device to + satisfy that request, otherwise 0 is returned + void pm_suspend_ignore_children(struct device *dev, bool enable); - set/unset the power.ignore_children flag of the device -- cgit v1.2.3-59-g8ed1b From 62052ab1d1a456f5f62f8b753e12d10ca1a83604 Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Wed, 6 Jul 2011 10:52:13 +0200 Subject: PM / Runtime: Replace "run-time" with "runtime" in documentation The runtime PM documentation and kerneldoc comments sometimes spell "runtime" with a dash (i.e. "run-time"). Replace all of those instances with "runtime" to make the naming consistent. Signed-off-by: Rafael J. Wysocki --- Documentation/power/runtime_pm.txt | 130 ++++++++++++++++++------------------- drivers/base/power/runtime.c | 66 +++++++++---------- 2 files changed, 98 insertions(+), 98 deletions(-) (limited to 'Documentation/power') diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index ca15bbbe1891..40e47c75f064 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -1,39 +1,39 @@ -Run-time Power Management Framework for I/O Devices +Runtime Power Management Framework for I/O Devices (C) 2009-2011 Rafael J. Wysocki , Novell Inc. (C) 2010 Alan Stern 1. Introduction -Support for run-time power management (run-time PM) of I/O devices is provided +Support for runtime power management (runtime PM) of I/O devices is provided at the power management core (PM core) level by means of: * The power management workqueue pm_wq in which bus types and device drivers can put their PM-related work items. It is strongly recommended that pm_wq be - used for queuing all work items related to run-time PM, because this allows + used for queuing all work items related to runtime PM, because this allows them to be synchronized with system-wide power transitions (suspend to RAM, hibernation and resume from system sleep states). pm_wq is declared in include/linux/pm_runtime.h and defined in kernel/power/main.c. -* A number of run-time PM fields in the 'power' member of 'struct device' (which +* A number of runtime PM fields in the 'power' member of 'struct device' (which is of the type 'struct dev_pm_info', defined in include/linux/pm.h) that can - be used for synchronizing run-time PM operations with one another. + be used for synchronizing runtime PM operations with one another. -* Three device run-time PM callbacks in 'struct dev_pm_ops' (defined in +* Three device runtime PM callbacks in 'struct dev_pm_ops' (defined in include/linux/pm.h). * A set of helper functions defined in drivers/base/power/runtime.c that can be - used for carrying out run-time PM operations in such a way that the + used for carrying out runtime PM operations in such a way that the synchronization between them is taken care of by the PM core. Bus types and device drivers are encouraged to use these functions. -The run-time PM callbacks present in 'struct dev_pm_ops', the device run-time PM +The runtime PM callbacks present in 'struct dev_pm_ops', the device runtime PM fields of 'struct dev_pm_info' and the core helper functions provided for -run-time PM are described below. +runtime PM are described below. -2. Device Run-time PM Callbacks +2. Device Runtime PM Callbacks -There are three device run-time PM callbacks defined in 'struct dev_pm_ops': +There are three device runtime PM callbacks defined in 'struct dev_pm_ops': struct dev_pm_ops { ... @@ -72,11 +72,11 @@ knows what to do to handle the device). not mean that the device has been put into a low power state. It is supposed to mean, however, that the device will not process data and will not communicate with the CPU(s) and RAM until the subsystem-level resume - callback is executed for it. The run-time PM status of a device after + callback is executed for it. The runtime PM status of a device after successful execution of the subsystem-level suspend callback is 'suspended'. * If the subsystem-level suspend callback returns -EBUSY or -EAGAIN, - the device's run-time PM status is 'active', which means that the device + the device's runtime PM status is 'active', which means that the device _must_ be fully operational afterwards. * If the subsystem-level suspend callback returns an error code different @@ -104,7 +104,7 @@ the device). * Once the subsystem-level resume callback has completed successfully, the PM core regards the device as fully operational, which means that the device - _must_ be able to complete I/O operations as needed. The run-time PM status + _must_ be able to complete I/O operations as needed. The runtime PM status of the device is then 'active'. * If the subsystem-level resume callback returns an error code, the PM core @@ -130,7 +130,7 @@ device in that case. The value returned by this callback is ignored by the PM core. The helper functions provided by the PM core, described in Section 4, guarantee -that the following constraints are met with respect to the bus type's run-time +that the following constraints are met with respect to the bus type's runtime PM callbacks: (1) The callbacks are mutually exclusive (e.g. it is forbidden to execute @@ -142,7 +142,7 @@ PM callbacks: (2) ->runtime_idle() and ->runtime_suspend() can only be executed for 'active' devices (i.e. the PM core will only execute ->runtime_idle() or - ->runtime_suspend() for the devices the run-time PM status of which is + ->runtime_suspend() for the devices the runtime PM status of which is 'active'). (3) ->runtime_idle() and ->runtime_suspend() can only be executed for a device @@ -151,7 +151,7 @@ PM callbacks: flag of which is set. (4) ->runtime_resume() can only be executed for 'suspended' devices (i.e. the - PM core will only execute ->runtime_resume() for the devices the run-time + PM core will only execute ->runtime_resume() for the devices the runtime PM status of which is 'suspended'). Additionally, the helper functions provided by the PM core obey the following @@ -171,9 +171,9 @@ rules: scheduled requests to execute the other callbacks for the same device, except for scheduled autosuspends. -3. Run-time PM Device Fields +3. Runtime PM Device Fields -The following device run-time PM fields are present in 'struct dev_pm_info', as +The following device runtime PM fields are present in 'struct dev_pm_info', as defined in include/linux/pm.h: struct timer_list suspend_timer; @@ -205,7 +205,7 @@ defined in include/linux/pm.h: unsigned int disable_depth; - used for disabling the helper funcions (they work normally if this is - equal to zero); the initial value of it is 1 (i.e. run-time PM is + equal to zero); the initial value of it is 1 (i.e. runtime PM is initially disabled for all devices) unsigned int runtime_error; @@ -229,10 +229,10 @@ defined in include/linux/pm.h: suspend to complete; means "start a resume as soon as you've suspended" unsigned int run_wake; - - set if the device is capable of generating run-time wake-up events + - set if the device is capable of generating runtime wake-up events enum rpm_status runtime_status; - - the run-time PM status of the device; this field's initial value is + - the runtime PM status of the device; this field's initial value is RPM_SUSPENDED, which means that each device is initially regarded by the PM core as 'suspended', regardless of its real hardware status @@ -243,7 +243,7 @@ defined in include/linux/pm.h: and pm_runtime_forbid() helper functions unsigned int no_callbacks; - - indicates that the device does not use the run-time PM callbacks (see + - indicates that the device does not use the runtime PM callbacks (see Section 8); it may be modified only by the pm_runtime_no_callbacks() helper function @@ -270,16 +270,16 @@ defined in include/linux/pm.h: All of the above fields are members of the 'power' member of 'struct device'. -4. Run-time PM Device Helper Functions +4. Runtime PM Device Helper Functions -The following run-time PM helper functions are defined in +The following runtime PM helper functions are defined in drivers/base/power/runtime.c and include/linux/pm_runtime.h: void pm_runtime_init(struct device *dev); - - initialize the device run-time PM fields in 'struct dev_pm_info' + - initialize the device runtime PM fields in 'struct dev_pm_info' void pm_runtime_remove(struct device *dev); - - make sure that the run-time PM of the device will be disabled after + - make sure that the runtime PM of the device will be disabled after removing the device from device hierarchy int pm_runtime_idle(struct device *dev); @@ -289,7 +289,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: int pm_runtime_suspend(struct device *dev); - execute the subsystem-level suspend callback for the device; returns 0 on - success, 1 if the device's run-time PM status was already 'suspended', or + success, 1 if the device's runtime PM status was already 'suspended', or error code on failure, where -EAGAIN or -EBUSY means it is safe to attempt to suspend the device again in future and -EACCES means that 'power.disable_depth' is different from 0 @@ -302,7 +302,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: int pm_runtime_resume(struct device *dev); - execute the subsystem-level resume callback for the device; returns 0 on - success, 1 if the device's run-time PM status was already 'active' or + success, 1 if the device's runtime PM status was already 'active' or error code on failure, where -EAGAIN means it may be safe to attempt to resume the device again in future, but 'power.runtime_error' should be checked additionally, and -EACCES means that 'power.disable_depth' is @@ -323,7 +323,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: device in future, where 'delay' is the time to wait before queuing up a suspend work item in pm_wq, in milliseconds (if 'delay' is zero, the work item is queued up immediately); returns 0 on success, 1 if the device's PM - run-time status was already 'suspended', or error code if the request + runtime status was already 'suspended', or error code if the request hasn't been scheduled (or queued up if 'delay' is 0); if the execution of ->runtime_suspend() is already scheduled and not yet expired, the new value of 'delay' will be used as the time to wait @@ -331,7 +331,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: int pm_request_resume(struct device *dev); - submit a request to execute the subsystem-level resume callback for the device (the request is represented by a work item in pm_wq); returns 0 on - success, 1 if the device's run-time PM status was already 'active', or + success, 1 if the device's runtime PM status was already 'active', or error code if the request hasn't been queued up void pm_runtime_get_noresume(struct device *dev); @@ -370,14 +370,14 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: void pm_runtime_enable(struct device *dev); - decrement the device's 'power.disable_depth' field; if that field is equal - to zero, the run-time PM helper functions can execute subsystem-level + to zero, the runtime PM helper functions can execute subsystem-level callbacks described in Section 2 for the device int pm_runtime_disable(struct device *dev); - increment the device's 'power.disable_depth' field (if the value of that field was previously zero, this prevents subsystem-level runtime PM callbacks from being run for the device), make sure that all of the pending - run-time PM operations on the device are either completed or canceled; + runtime PM operations on the device are either completed or canceled; returns 1 if there was a resume request pending and it was necessary to execute the subsystem-level resume callback for the device to satisfy that request, otherwise 0 is returned @@ -394,7 +394,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: - set/unset the power.ignore_children flag of the device int pm_runtime_set_active(struct device *dev); - - clear the device's 'power.runtime_error' flag, set the device's run-time + - clear the device's 'power.runtime_error' flag, set the device's runtime PM status to 'active' and update its parent's counter of 'active' children as appropriate (it is only valid to use this function if 'power.runtime_error' is set or 'power.disable_depth' is greater than @@ -402,7 +402,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: which is not active and the 'power.ignore_children' flag of which is unset void pm_runtime_set_suspended(struct device *dev); - - clear the device's 'power.runtime_error' flag, set the device's run-time + - clear the device's 'power.runtime_error' flag, set the device's runtime PM status to 'suspended' and update its parent's counter of 'active' children as appropriate (it is only valid to use this function if 'power.runtime_error' is set or 'power.disable_depth' is greater than @@ -423,7 +423,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: effectively prevent the device from being power managed at run time) void pm_runtime_no_callbacks(struct device *dev); - - set the power.no_callbacks flag for the device and remove the run-time + - set the power.no_callbacks flag for the device and remove the runtime PM attributes from /sys/devices/.../power (or prevent them from being added when the device is registered) @@ -443,7 +443,7 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: void pm_runtime_set_autosuspend_delay(struct device *dev, int delay); - set the power.autosuspend_delay value to 'delay' (expressed in - milliseconds); if 'delay' is negative then run-time suspends are + milliseconds); if 'delay' is negative then runtime suspends are prevented unsigned long pm_runtime_autosuspend_expiration(struct device *dev); @@ -482,35 +482,35 @@ pm_runtime_resume() pm_runtime_get_sync() pm_runtime_put_sync_suspend() -5. Run-time PM Initialization, Device Probing and Removal +5. Runtime PM Initialization, Device Probing and Removal -Initially, the run-time PM is disabled for all devices, which means that the -majority of the run-time PM helper funtions described in Section 4 will return +Initially, the runtime PM is disabled for all devices, which means that the +majority of the runtime PM helper funtions described in Section 4 will return -EAGAIN until pm_runtime_enable() is called for the device. -In addition to that, the initial run-time PM status of all devices is +In addition to that, the initial runtime PM status of all devices is 'suspended', but it need not reflect the actual physical state of the device. Thus, if the device is initially active (i.e. it is able to process I/O), its -run-time PM status must be changed to 'active', with the help of +runtime PM status must be changed to 'active', with the help of pm_runtime_set_active(), before pm_runtime_enable() is called for the device. -However, if the device has a parent and the parent's run-time PM is enabled, +However, if the device has a parent and the parent's runtime PM is enabled, calling pm_runtime_set_active() for the device will affect the parent, unless the parent's 'power.ignore_children' flag is set. Namely, in that case the parent won't be able to suspend at run time, using the PM core's helper functions, as long as the child's status is 'active', even if the child's -run-time PM is still disabled (i.e. pm_runtime_enable() hasn't been called for +runtime PM is still disabled (i.e. pm_runtime_enable() hasn't been called for the child yet or pm_runtime_disable() has been called for it). For this reason, once pm_runtime_set_active() has been called for the device, pm_runtime_enable() -should be called for it too as soon as reasonably possible or its run-time PM +should be called for it too as soon as reasonably possible or its runtime PM status should be changed back to 'suspended' with the help of pm_runtime_set_suspended(). -If the default initial run-time PM status of the device (i.e. 'suspended') +If the default initial runtime PM status of the device (i.e. 'suspended') reflects the actual state of the device, its bus type's or its driver's ->probe() callback will likely need to wake it up using one of the PM core's helper functions described in Section 4. In that case, pm_runtime_resume() -should be used. Of course, for this purpose the device's run-time PM has to be +should be used. Of course, for this purpose the device's runtime PM has to be enabled earlier by calling pm_runtime_enable(). If the device bus type's or driver's ->probe() callback runs @@ -541,29 +541,29 @@ The user space can effectively disallow the driver of the device to power manage it at run time by changing the value of its /sys/devices/.../power/control attribute to "on", which causes pm_runtime_forbid() to be called. In principle, this mechanism may also be used by the driver to effectively turn off the -run-time power management of the device until the user space turns it on. -Namely, during the initialization the driver can make sure that the run-time PM +runtime power management of the device until the user space turns it on. +Namely, during the initialization the driver can make sure that the runtime PM status of the device is 'active' and call pm_runtime_forbid(). It should be noted, however, that if the user space has already intentionally changed the value of /sys/devices/.../power/control to "auto" to allow the driver to power manage the device at run time, the driver may confuse it by using pm_runtime_forbid() this way. -6. Run-time PM and System Sleep +6. Runtime PM and System Sleep -Run-time PM and system sleep (i.e., system suspend and hibernation, also known +Runtime PM and system sleep (i.e., system suspend and hibernation, also known as suspend-to-RAM and suspend-to-disk) interact with each other in a couple of ways. If a device is active when a system sleep starts, everything is straightforward. But what should happen if the device is already suspended? -The device may have different wake-up settings for run-time PM and system sleep. -For example, remote wake-up may be enabled for run-time suspend but disallowed +The device may have different wake-up settings for runtime PM and system sleep. +For example, remote wake-up may be enabled for runtime suspend but disallowed for system sleep (device_may_wakeup(dev) returns 'false'). When this happens, the subsystem-level system suspend callback is responsible for changing the device's wake-up setting (it may leave that to the device driver's system suspend routine). It may be necessary to resume the device and suspend it again in order to do so. The same is true if the driver uses different power levels -or other settings for run-time suspend and system sleep. +or other settings for runtime suspend and system sleep. During system resume, the simplest approach is to bring all devices back to full power, even if they had been suspended before the system suspend began. There @@ -582,10 +582,10 @@ are several reasons for this, including: * The device might need to be reset. * Even though the device was suspended, if its usage counter was > 0 then most - likely it would need a run-time resume in the near future anyway. + likely it would need a runtime resume in the near future anyway. If the device had been suspended before the system suspend began and it's -brought back to full power during resume, then its run-time PM status will have +brought back to full power during resume, then its runtime PM status will have to be updated to reflect the actual post-system sleep status. The way to do this is: @@ -593,9 +593,9 @@ this is: pm_runtime_set_active(dev); pm_runtime_enable(dev); -The PM core always increments the run-time usage counter before calling the +The PM core always increments the runtime usage counter before calling the ->suspend() callback and decrements it after calling the ->resume() callback. -Hence disabling run-time PM temporarily like this will not cause any runtime +Hence disabling runtime PM temporarily like this will not cause any runtime suspend attempts to be permanently lost. If the usage count goes to zero following the return of the ->resume() callback, the ->runtime_idle() callback will be invoked as usual. @@ -710,8 +710,8 @@ the GENERIC_SUBSYS_PM_OPS macro, defined in include/linux/pm.h, to its dev_pm_ops structure pointer. Device drivers that wish to use the same function as a system suspend, freeze, -poweroff and run-time suspend callback, and similarly for system resume, thaw, -restore, and run-time resume, can achieve this with the help of the +poweroff and runtime suspend callback, and similarly for system resume, thaw, +restore, and runtime resume, can achieve this with the help of the UNIVERSAL_DEV_PM_OPS macro defined in include/linux/pm.h (possibly setting its last argument to NULL). @@ -721,7 +721,7 @@ Some "devices" are only logical sub-devices of their parent and cannot be power-managed on their own. (The prototype example is a USB interface. Entire USB devices can go into low-power mode or send wake-up requests, but neither is possible for individual interfaces.) The drivers for these devices have no -need of run-time PM callbacks; if the callbacks did exist, ->runtime_suspend() +need of runtime PM callbacks; if the callbacks did exist, ->runtime_suspend() and ->runtime_resume() would always return 0 without doing anything else and ->runtime_idle() would always call pm_runtime_suspend(). @@ -729,7 +729,7 @@ Subsystems can tell the PM core about these devices by calling pm_runtime_no_callbacks(). This should be done after the device structure is initialized and before it is registered (although after device registration is also okay). The routine will set the device's power.no_callbacks flag and -prevent the non-debugging run-time PM sysfs attributes from being created. +prevent the non-debugging runtime PM sysfs attributes from being created. When power.no_callbacks is set, the PM core will not invoke the ->runtime_idle(), ->runtime_suspend(), or ->runtime_resume() callbacks. @@ -737,7 +737,7 @@ Instead it will assume that suspends and resumes always succeed and that idle devices should be suspended. As a consequence, the PM core will never directly inform the device's subsystem -or driver about run-time power changes. Instead, the driver for the device's +or driver about runtime power changes. Instead, the driver for the device's parent must take responsibility for telling the device's driver when the parent's power state changes. @@ -748,13 +748,13 @@ A device should be put in a low-power state only when there's some reason to think it will remain in that state for a substantial time. A common heuristic says that a device which hasn't been used for a while is liable to remain unused; following this advice, drivers should not allow devices to be suspended -at run-time until they have been inactive for some minimum period. Even when +at runtime until they have been inactive for some minimum period. Even when the heuristic ends up being non-optimal, it will still prevent devices from "bouncing" too rapidly between low-power and full-power states. The term "autosuspend" is an historical remnant. It doesn't mean that the device is automatically suspended (the subsystem or driver still has to call -the appropriate PM routines); rather it means that run-time suspends will +the appropriate PM routines); rather it means that runtime suspends will automatically be delayed until the desired period of inactivity has elapsed. Inactivity is determined based on the power.last_busy field. Drivers should diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c index ee99025be6b3..be7b982d252e 100644 --- a/drivers/base/power/runtime.c +++ b/drivers/base/power/runtime.c @@ -1,5 +1,5 @@ /* - * drivers/base/power/runtime.c - Helper functions for device run-time PM + * drivers/base/power/runtime.c - Helper functions for device runtime PM * * Copyright (c) 2009 Rafael J. Wysocki , Novell Inc. * Copyright (C) 2010 Alan Stern @@ -159,7 +159,7 @@ static int rpm_check_suspend_allowed(struct device *dev) * @dev: Device to notify the bus type about. * @rpmflags: Flag bits. * - * Check if the device's run-time PM status allows it to be suspended. If + * Check if the device's runtime PM status allows it to be suspended. If * another idle notification has been started earlier, return immediately. If * the RPM_ASYNC flag is set then queue an idle-notification request; otherwise * run the ->runtime_idle() callback directly. @@ -267,11 +267,11 @@ static int rpm_callback(int (*cb)(struct device *), struct device *dev) } /** - * rpm_suspend - Carry out run-time suspend of given device. + * rpm_suspend - Carry out runtime suspend of given device. * @dev: Device to suspend. * @rpmflags: Flag bits. * - * Check if the device's run-time PM status allows it to be suspended. If + * Check if the device's runtime PM status allows it to be suspended. If * another suspend has been started earlier, either return immediately or wait * for it to finish, depending on the RPM_NOWAIT and RPM_ASYNC flags. Cancel a * pending idle notification. If the RPM_ASYNC flag is set then queue a @@ -430,11 +430,11 @@ static int rpm_suspend(struct device *dev, int rpmflags) } /** - * rpm_resume - Carry out run-time resume of given device. + * rpm_resume - Carry out runtime resume of given device. * @dev: Device to resume. * @rpmflags: Flag bits. * - * Check if the device's run-time PM status allows it to be resumed. Cancel + * Check if the device's runtime PM status allows it to be resumed. Cancel * any scheduled or pending requests. If another resume has been started * earlier, either return immediately or wait for it to finish, depending on the * RPM_NOWAIT and RPM_ASYNC flags. Similarly, if there's a suspend running in @@ -551,7 +551,7 @@ static int rpm_resume(struct device *dev, int rpmflags) spin_lock(&parent->power.lock); /* - * We can resume if the parent's run-time PM is disabled or it + * We can resume if the parent's runtime PM is disabled or it * is set to ignore children. */ if (!parent->power.disable_depth @@ -615,11 +615,11 @@ static int rpm_resume(struct device *dev, int rpmflags) } /** - * pm_runtime_work - Universal run-time PM work function. + * pm_runtime_work - Universal runtime PM work function. * @work: Work structure used for scheduling the execution of this function. * * Use @work to get the device object the work is to be done for, determine what - * is to be done and execute the appropriate run-time PM function. + * is to be done and execute the appropriate runtime PM function. */ static void pm_runtime_work(struct work_struct *work) { @@ -718,7 +718,7 @@ int pm_schedule_suspend(struct device *dev, unsigned int delay) EXPORT_SYMBOL_GPL(pm_schedule_suspend); /** - * __pm_runtime_idle - Entry point for run-time idle operations. + * __pm_runtime_idle - Entry point for runtime idle operations. * @dev: Device to send idle notification for. * @rpmflags: Flag bits. * @@ -747,7 +747,7 @@ int __pm_runtime_idle(struct device *dev, int rpmflags) EXPORT_SYMBOL_GPL(__pm_runtime_idle); /** - * __pm_runtime_suspend - Entry point for run-time put/suspend operations. + * __pm_runtime_suspend - Entry point for runtime put/suspend operations. * @dev: Device to suspend. * @rpmflags: Flag bits. * @@ -776,7 +776,7 @@ int __pm_runtime_suspend(struct device *dev, int rpmflags) EXPORT_SYMBOL_GPL(__pm_runtime_suspend); /** - * __pm_runtime_resume - Entry point for run-time resume operations. + * __pm_runtime_resume - Entry point for runtime resume operations. * @dev: Device to resume. * @rpmflags: Flag bits. * @@ -802,11 +802,11 @@ int __pm_runtime_resume(struct device *dev, int rpmflags) EXPORT_SYMBOL_GPL(__pm_runtime_resume); /** - * __pm_runtime_set_status - Set run-time PM status of a device. + * __pm_runtime_set_status - Set runtime PM status of a device. * @dev: Device to handle. - * @status: New run-time PM status of the device. + * @status: New runtime PM status of the device. * - * If run-time PM of the device is disabled or its power.runtime_error field is + * If runtime PM of the device is disabled or its power.runtime_error field is * different from zero, the status may be changed either to RPM_ACTIVE, or to * RPM_SUSPENDED, as long as that reflects the actual state of the device. * However, if the device has a parent and the parent is not active, and the @@ -852,7 +852,7 @@ int __pm_runtime_set_status(struct device *dev, unsigned int status) /* * It is invalid to put an active child under a parent that is - * not active, has run-time PM enabled and the + * not active, has runtime PM enabled and the * 'power.ignore_children' flag unset. */ if (!parent->power.disable_depth @@ -886,7 +886,7 @@ EXPORT_SYMBOL_GPL(__pm_runtime_set_status); * @dev: Device to handle. * * Flush all pending requests for the device from pm_wq and wait for all - * run-time PM operations involving the device in progress to complete. + * runtime PM operations involving the device in progress to complete. * * Should be called under dev->power.lock with interrupts disabled. */ @@ -934,7 +934,7 @@ static void __pm_runtime_barrier(struct device *dev) * Prevent the device from being suspended by incrementing its usage counter and * if there's a pending resume request for the device, wake the device up. * Next, make sure that all pending requests for the device have been flushed - * from pm_wq and wait for all run-time PM operations involving the device in + * from pm_wq and wait for all runtime PM operations involving the device in * progress to complete. * * Return value: @@ -964,18 +964,18 @@ int pm_runtime_barrier(struct device *dev) EXPORT_SYMBOL_GPL(pm_runtime_barrier); /** - * __pm_runtime_disable - Disable run-time PM of a device. + * __pm_runtime_disable - Disable runtime PM of a device. * @dev: Device to handle. * @check_resume: If set, check if there's a resume request for the device. * * Increment power.disable_depth for the device and if was zero previously, - * cancel all pending run-time PM requests for the device and wait for all + * cancel all pending runtime PM requests for the device and wait for all * operations in progress to complete. The device can be either active or - * suspended after its run-time PM has been disabled. + * suspended after its runtime PM has been disabled. * * If @check_resume is set and there's a resume request pending when * __pm_runtime_disable() is called and power.disable_depth is zero, the - * function will wake up the device before disabling its run-time PM. + * function will wake up the device before disabling its runtime PM. */ void __pm_runtime_disable(struct device *dev, bool check_resume) { @@ -988,7 +988,7 @@ void __pm_runtime_disable(struct device *dev, bool check_resume) /* * Wake up the device if there's a resume request pending, because that - * means there probably is some I/O to process and disabling run-time PM + * means there probably is some I/O to process and disabling runtime PM * shouldn't prevent the device from processing the I/O. */ if (check_resume && dev->power.request_pending @@ -1013,7 +1013,7 @@ void __pm_runtime_disable(struct device *dev, bool check_resume) EXPORT_SYMBOL_GPL(__pm_runtime_disable); /** - * pm_runtime_enable - Enable run-time PM of a device. + * pm_runtime_enable - Enable runtime PM of a device. * @dev: Device to handle. */ void pm_runtime_enable(struct device *dev) @@ -1032,7 +1032,7 @@ void pm_runtime_enable(struct device *dev) EXPORT_SYMBOL_GPL(pm_runtime_enable); /** - * pm_runtime_forbid - Block run-time PM of a device. + * pm_runtime_forbid - Block runtime PM of a device. * @dev: Device to handle. * * Increase the device's usage count and clear its power.runtime_auto flag, @@ -1055,7 +1055,7 @@ void pm_runtime_forbid(struct device *dev) EXPORT_SYMBOL_GPL(pm_runtime_forbid); /** - * pm_runtime_allow - Unblock run-time PM of a device. + * pm_runtime_allow - Unblock runtime PM of a device. * @dev: Device to handle. * * Decrease the device's usage count and set its power.runtime_auto flag. @@ -1076,12 +1076,12 @@ void pm_runtime_allow(struct device *dev) EXPORT_SYMBOL_GPL(pm_runtime_allow); /** - * pm_runtime_no_callbacks - Ignore run-time PM callbacks for a device. + * pm_runtime_no_callbacks - Ignore runtime PM callbacks for a device. * @dev: Device to handle. * * Set the power.no_callbacks flag, which tells the PM core that this - * device is power-managed through its parent and has no run-time PM - * callbacks of its own. The run-time sysfs attributes will be removed. + * device is power-managed through its parent and has no runtime PM + * callbacks of its own. The runtime sysfs attributes will be removed. */ void pm_runtime_no_callbacks(struct device *dev) { @@ -1157,8 +1157,8 @@ static void update_autosuspend(struct device *dev, int old_delay, int old_use) * @delay: Value of the new delay in milliseconds. * * Set the device's power.autosuspend_delay value. If it changes to negative - * and the power.use_autosuspend flag is set, prevent run-time suspends. If it - * changes the other way, allow run-time suspends. + * and the power.use_autosuspend flag is set, prevent runtime suspends. If it + * changes the other way, allow runtime suspends. */ void pm_runtime_set_autosuspend_delay(struct device *dev, int delay) { @@ -1178,7 +1178,7 @@ EXPORT_SYMBOL_GPL(pm_runtime_set_autosuspend_delay); * @dev: Device to handle. * @use: New value for use_autosuspend. * - * Set the device's power.use_autosuspend flag, and allow or prevent run-time + * Set the device's power.use_autosuspend flag, and allow or prevent runtime * suspends as needed. */ void __pm_runtime_use_autosuspend(struct device *dev, bool use) @@ -1195,7 +1195,7 @@ void __pm_runtime_use_autosuspend(struct device *dev, bool use) EXPORT_SYMBOL_GPL(__pm_runtime_use_autosuspend); /** - * pm_runtime_init - Initialize run-time PM fields in given device object. + * pm_runtime_init - Initialize runtime PM fields in given device object. * @dev: Device object to initialize. */ void pm_runtime_init(struct device *dev) -- cgit v1.2.3-59-g8ed1b From f3393b62f157cc87f8d78247e97b87778dc077b8 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 12 Jul 2011 11:17:09 +0200 Subject: PM / Runtime: Add new helper function: pm_runtime_status_suspended() This boolean function simply returns whether or not the runtime status of the device is 'suspended'. Unlike pm_runtime_suspended(), this function returns the runtime status whether or not runtime PM for the device has been disabled or not. Also add entry to Documentation/power/runtime.txt Signed-off-by: Kevin Hilman Signed-off-by: Rafael J. Wysocki --- Documentation/power/runtime_pm.txt | 3 +++ include/linux/pm_runtime.h | 6 ++++++ 2 files changed, 9 insertions(+) (limited to 'Documentation/power') diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt index 40e47c75f064..14dd3c6ad97e 100644 --- a/Documentation/power/runtime_pm.txt +++ b/Documentation/power/runtime_pm.txt @@ -412,6 +412,9 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h: - return true if the device's runtime PM status is 'suspended' and its 'power.disable_depth' field is equal to zero, or false otherwise + bool pm_runtime_status_suspended(struct device *dev); + - return true if the device's runtime PM status is 'suspended' + void pm_runtime_allow(struct device *dev); - set the power.runtime_auto flag for the device and decrease its usage counter (used by the /sys/devices/.../power/control interface to diff --git a/include/linux/pm_runtime.h b/include/linux/pm_runtime.h index dfb8539ed686..daac05d751b2 100644 --- a/include/linux/pm_runtime.h +++ b/include/linux/pm_runtime.h @@ -82,6 +82,11 @@ static inline bool pm_runtime_suspended(struct device *dev) && !dev->power.disable_depth; } +static inline bool pm_runtime_status_suspended(struct device *dev) +{ + return dev->power.runtime_status == RPM_SUSPENDED; +} + static inline bool pm_runtime_enabled(struct device *dev) { return !dev->power.disable_depth; @@ -130,6 +135,7 @@ static inline void pm_runtime_put_noidle(struct device *dev) {} static inline bool device_run_wake(struct device *dev) { return false; } static inline void device_set_run_wake(struct device *dev, bool enable) {} static inline bool pm_runtime_suspended(struct device *dev) { return false; } +static inline bool pm_runtime_status_suspended(struct device *dev) { return false; } static inline bool pm_runtime_enabled(struct device *dev) { return false; } static inline int pm_generic_runtime_idle(struct device *dev) { return 0; } -- cgit v1.2.3-59-g8ed1b