From 8f67eeb0b44cde19216955975ffef8513a87c0c0 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 18 Sep 2009 22:45:48 +0200 Subject: i2c/chips: Remove deprecated pcf8575 driver The pcf8575 driver in drivers/i2c/chips which just exports its register to sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib. As this driver has been deprecated for more than a year, finally remove it. Signed-off-by: Wolfram Sang Cc: Bart Van Assche Signed-off-by: Jean Delvare --- Documentation/i2c/chips/pcf8575 | 69 ----------------------------------------- 1 file changed, 69 deletions(-) delete mode 100644 Documentation/i2c/chips/pcf8575 (limited to 'Documentation') diff --git a/Documentation/i2c/chips/pcf8575 b/Documentation/i2c/chips/pcf8575 deleted file mode 100644 index 40b268eb276f..000000000000 --- a/Documentation/i2c/chips/pcf8575 +++ /dev/null @@ -1,69 +0,0 @@ -About the PCF8575 chip and the pcf8575 kernel driver -==================================================== - -The PCF8575 chip is produced by the following manufacturers: - - * Philips NXP - http://www.nxp.com/#/pip/cb=[type=product,path=50807/41735/41850,final=PCF8575_3]|pip=[pip=PCF8575_3][0] - - * Texas Instruments - http://focus.ti.com/docs/prod/folders/print/pcf8575.html - - -Some vendors sell small PCB's with the PCF8575 mounted on it. You can connect -such a board to a Linux host via e.g. an USB to I2C interface. Examples of -PCB boards with a PCF8575: - - * SFE Breakout Board for PCF8575 I2C Expander by RobotShop - http://www.robotshop.ca/home/products/robot-parts/electronics/adapters-converters/sfe-pcf8575-i2c-expander-board.html - - * Breakout Board for PCF8575 I2C Expander by Spark Fun Electronics - http://www.sparkfun.com/commerce/product_info.php?products_id=8130 - - -Description ------------ -The PCF8575 chip is a 16-bit I/O expander for the I2C bus. Up to eight of -these chips can be connected to the same I2C bus. You can find this -chip on some custom designed hardware, but you won't find it on PC -motherboards. - -The PCF8575 chip consists of a 16-bit quasi-bidirectional port and an I2C-bus -interface. Each of the sixteen I/O's can be independently used as an input or -an output. To set up an I/O pin as an input, you have to write a 1 to the -corresponding output. - -For more information please see the datasheet. - - -Detection ---------- - -There is no method known to detect whether a chip on a given I2C address is -a PCF8575 or whether it is any other I2C device, so you have to pass the I2C -bus and address of the installed PCF8575 devices explicitly to the driver at -load time via the force=... parameter. - -/sys interface --------------- - -For each address on which a PCF8575 chip was found or forced the following -files will be created under /sys: -* /sys/bus/i2c/devices/-
/read -* /sys/bus/i2c/devices/-
/write -where bus is the I2C bus number (0, 1, ...) and address is the four-digit -hexadecimal representation of the 7-bit I2C address of the PCF8575 -(0020 .. 0027). - -The read file is read-only. Reading it will trigger an I2C read and will hence -report the current input state for the pins configured as inputs, and the -current output value for the pins configured as outputs. - -The write file is read-write. Writing a value to it will configure all pins -as output for which the corresponding bit is zero. Reading the write file will -return the value last written, or -EAGAIN if no value has yet been written to -the write file. - -On module initialization the configuration of the chip is not changed -- the -chip is left in the state it was already configured in through either power-up -or through previous I2C write actions. -- cgit v1.2.3-59-g8ed1b From 732d481127abaa0add41ee918191ea08e9ede17e Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 18 Sep 2009 22:45:48 +0200 Subject: i2c/chips: Remove deprecated pca9539 driver The pca9539 driver in drivers/i2c/chips which just exports its registers to sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib. As this driver has been deprecated for more than a year, finally remove it. Signed-off-by: Wolfram Sang Acked-by: Ben Gardner Signed-off-by: Jean Delvare --- Documentation/i2c/chips/pca9539 | 58 --------------- drivers/i2c/chips/Kconfig | 13 ---- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/pca9539.c | 152 ---------------------------------------- 4 files changed, 224 deletions(-) delete mode 100644 Documentation/i2c/chips/pca9539 delete mode 100644 drivers/i2c/chips/pca9539.c (limited to 'Documentation') diff --git a/Documentation/i2c/chips/pca9539 b/Documentation/i2c/chips/pca9539 deleted file mode 100644 index 6aff890088b1..000000000000 --- a/Documentation/i2c/chips/pca9539 +++ /dev/null @@ -1,58 +0,0 @@ -Kernel driver pca9539 -===================== - -NOTE: this driver is deprecated and will be dropped soon, use -drivers/gpio/pca9539.c instead. - -Supported chips: - * Philips PCA9539 - Prefix: 'pca9539' - Addresses scanned: none - Datasheet: - http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf - -Author: Ben Gardner - - -Description ------------ - -The Philips PCA9539 is a 16 bit low power I/O device. -All 16 lines can be individually configured as an input or output. -The input sense can also be inverted. -The 16 lines are split between two bytes. - - -Detection ---------- - -The PCA9539 is difficult to detect and not commonly found in PC machines, -so you have to pass the I2C bus and address of the installed PCA9539 -devices explicitly to the driver at load time via the force=... parameter. - - -Sysfs entries -------------- - -Each is a byte that maps to the 8 I/O bits. -A '0' suffix is for bits 0-7, while '1' is for bits 8-15. - -input[01] - read the current value -output[01] - sets the output value -direction[01] - direction of each bit: 1=input, 0=output -invert[01] - toggle the input bit sense - -input reads the actual state of the line and is always available. -The direction defaults to input for all channels. - - -General Remarks ---------------- - -Note that each output, direction, and invert entry controls 8 lines. -You should use the read, modify, write sequence. -For example. to set output bit 0 of 1. - val=$(cat output0) - val=$(( $val | 1 )) - echo $val > output0 - diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 1b5455ec2903..8cd1a7f3dcbe 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -33,19 +33,6 @@ config SENSORS_PCF8574 These devices are hard to detect and rarely found on mainstream hardware. If unsure, say N. -config SENSORS_PCA9539 - tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCA953X = "n" - help - If you say yes here you get support for the Philips PCA9539 - 16-bit I/O port. - - This driver can also be built as a module. If so, the module - will be called pca9539. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pca953x.c instead. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index fceb377f5280..8cd778dd64e5 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o diff --git a/drivers/i2c/chips/pca9539.c b/drivers/i2c/chips/pca9539.c deleted file mode 100644 index 270de4e56a81..000000000000 --- a/drivers/i2c/chips/pca9539.c +++ /dev/null @@ -1,152 +0,0 @@ -/* - pca9539.c - 16-bit I/O port with interrupt and reset - - Copyright (C) 2005 Ben Gardner - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; version 2 of the License. -*/ - -#include -#include -#include -#include -#include - -/* Addresses to scan: none, device is not autodetected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(pca9539); - -enum pca9539_cmd -{ - PCA9539_INPUT_0 = 0, - PCA9539_INPUT_1 = 1, - PCA9539_OUTPUT_0 = 2, - PCA9539_OUTPUT_1 = 3, - PCA9539_INVERT_0 = 4, - PCA9539_INVERT_1 = 5, - PCA9539_DIRECTION_0 = 6, - PCA9539_DIRECTION_1 = 7, -}; - -/* following are the sysfs callback functions */ -static ssize_t pca9539_show(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%d\n", i2c_smbus_read_byte_data(client, - psa->index)); -} - -static ssize_t pca9539_store(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - unsigned long val = simple_strtoul(buf, NULL, 0); - if (val > 0xff) - return -EINVAL; - i2c_smbus_write_byte_data(client, psa->index, val); - return count; -} - -/* Define the device attributes */ - -#define PCA9539_ENTRY_RO(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO, pca9539_show, NULL, cmd_idx) - -#define PCA9539_ENTRY_RW(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO | S_IWUSR, pca9539_show, \ - pca9539_store, cmd_idx) - -PCA9539_ENTRY_RO(input0, PCA9539_INPUT_0); -PCA9539_ENTRY_RO(input1, PCA9539_INPUT_1); -PCA9539_ENTRY_RW(output0, PCA9539_OUTPUT_0); -PCA9539_ENTRY_RW(output1, PCA9539_OUTPUT_1); -PCA9539_ENTRY_RW(invert0, PCA9539_INVERT_0); -PCA9539_ENTRY_RW(invert1, PCA9539_INVERT_1); -PCA9539_ENTRY_RW(direction0, PCA9539_DIRECTION_0); -PCA9539_ENTRY_RW(direction1, PCA9539_DIRECTION_1); - -static struct attribute *pca9539_attributes[] = { - &sensor_dev_attr_input0.dev_attr.attr, - &sensor_dev_attr_input1.dev_attr.attr, - &sensor_dev_attr_output0.dev_attr.attr, - &sensor_dev_attr_output1.dev_attr.attr, - &sensor_dev_attr_invert0.dev_attr.attr, - &sensor_dev_attr_invert1.dev_attr.attr, - &sensor_dev_attr_direction0.dev_attr.attr, - &sensor_dev_attr_direction1.dev_attr.attr, - NULL -}; - -static struct attribute_group pca9539_defattr_group = { - .attrs = pca9539_attributes, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pca9539_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -ENODEV; - - strlcpy(info->type, "pca9539", I2C_NAME_SIZE); - - return 0; -} - -static int pca9539_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - /* Register sysfs hooks */ - return sysfs_create_group(&client->dev.kobj, - &pca9539_defattr_group); -} - -static int pca9539_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pca9539_defattr_group); - return 0; -} - -static const struct i2c_device_id pca9539_id[] = { - { "pca9539", 0 }, - { } -}; - -static struct i2c_driver pca9539_driver = { - .driver = { - .name = "pca9539", - }, - .probe = pca9539_probe, - .remove = pca9539_remove, - .id_table = pca9539_id, - - .detect = pca9539_detect, - .address_data = &addr_data, -}; - -static int __init pca9539_init(void) -{ - return i2c_add_driver(&pca9539_driver); -} - -static void __exit pca9539_exit(void) -{ - i2c_del_driver(&pca9539_driver); -} - -MODULE_AUTHOR("Ben Gardner "); -MODULE_DESCRIPTION("PCA9539 driver"); -MODULE_LICENSE("GPL"); - -module_init(pca9539_init); -module_exit(pca9539_exit); - -- cgit v1.2.3-59-g8ed1b From e7c5c49ecdac6dc5a6b67a27838b1b562eeec1b9 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 18 Sep 2009 22:45:49 +0200 Subject: i2c/chips: Remove deprecated pcf8574 driver The pcf8574 driver in drivers/i2c/chips which just exports its register to sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib. As this driver has been deprecated for more than a year, finally remove it. Signed-off-by: Wolfram Sang Cc: Aurelien Jarno Signed-off-by: Jean Delvare --- Documentation/i2c/chips/pcf8574 | 65 ------------ drivers/i2c/chips/Kconfig | 17 ---- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/pcf8574.c | 215 ---------------------------------------- 4 files changed, 298 deletions(-) delete mode 100644 Documentation/i2c/chips/pcf8574 delete mode 100644 drivers/i2c/chips/pcf8574.c (limited to 'Documentation') diff --git a/Documentation/i2c/chips/pcf8574 b/Documentation/i2c/chips/pcf8574 deleted file mode 100644 index 235815c075ff..000000000000 --- a/Documentation/i2c/chips/pcf8574 +++ /dev/null @@ -1,65 +0,0 @@ -Kernel driver pcf8574 -===================== - -Supported chips: - * Philips PCF8574 - Prefix: 'pcf8574' - Addresses scanned: none - Datasheet: Publicly available at the Philips Semiconductors website - http://www.semiconductors.philips.com/pip/PCF8574P.html - - * Philips PCF8574A - Prefix: 'pcf8574a' - Addresses scanned: none - Datasheet: Publicly available at the Philips Semiconductors website - http://www.semiconductors.philips.com/pip/PCF8574P.html - -Authors: - Frodo Looijaard , - Philip Edelbrock , - Dan Eaton , - Aurelien Jarno , - Jean Delvare , - - -Description ------------ -The PCF8574(A) is an 8-bit I/O expander for the I2C bus produced by Philips -Semiconductors. It is designed to provide a byte I2C interface to up to 16 -separate devices (8 x PCF8574 and 8 x PCF8574A). - -This device consists of a quasi-bidirectional port. Each of the eight I/Os -can be independently used as an input or output. To setup an I/O as an -input, you have to write a 1 to the corresponding output. - -For more informations see the datasheet. - - -Accessing PCF8574(A) via /sys interface -------------------------------------- - -The PCF8574(A) is plainly impossible to detect ! Stupid chip. -So, you have to pass the I2C bus and address of the installed PCF857A -and PCF8574A devices explicitly to the driver at load time via the -force=... parameter. - -On detection (i.e. insmod, modprobe et al.), directories are being -created for each detected PCF8574(A): - -/sys/bus/i2c/devices/<0>-<1>/ -where <0> is the bus the chip was detected on (e. g. i2c-0) -and <1> the chip address ([20..27] or [38..3f]): - -(example: /sys/bus/i2c/devices/1-0020/) - -Inside these directories, there are two files each: -read and write (and one file with chip name). - -The read file is read-only. Reading gives you the current I/O input -if the corresponding output is set as 1, otherwise the current output -value, that is to say 0. - -The write file is read/write. Writing a value outputs it on the I/O -port. Reading returns the last written value. As it is not possible -to read this value from the chip, you need to write at least once to -this file before you can read back from it. diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 8cd1a7f3dcbe..f9618f4d4e47 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -16,23 +16,6 @@ config DS1682 This driver can also be built as a module. If so, the module will be called ds1682. -config SENSORS_PCF8574 - tristate "Philips PCF8574 and PCF8574A (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCF857X = "n" - default n - help - If you say yes here you get support for Philips PCF8574 and - PCF8574A chips. These chips are 8-bit I/O expanders for the I2C bus. - - This driver can also be built as a module. If so, the module - will be called pcf8574. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pcf857x.c instead. - - These devices are hard to detect and rarely found on mainstream - hardware. If unsure, say N. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index 8cd778dd64e5..749cf3606294 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o ifeq ($(CONFIG_I2C_DEBUG_CHIP),y) diff --git a/drivers/i2c/chips/pcf8574.c b/drivers/i2c/chips/pcf8574.c deleted file mode 100644 index 6ec309894c88..000000000000 --- a/drivers/i2c/chips/pcf8574.c +++ /dev/null @@ -1,215 +0,0 @@ -/* - Copyright (c) 2000 Frodo Looijaard , - Philip Edelbrock , - Dan Eaton - Ported to Linux 2.6 by Aurelien Jarno with - the help of Jean Delvare - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -/* A few notes about the PCF8574: - -* The PCF8574 is an 8-bit I/O expander for the I2C bus produced by - Philips Semiconductors. It is designed to provide a byte I2C - interface to up to 8 separate devices. - -* The PCF8574 appears as a very simple SMBus device which can be - read from or written to with SMBUS byte read/write accesses. - - --Dan - -*/ - -#include -#include -#include -#include - -/* Addresses to scan: none, device can't be detected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_2(pcf8574, pcf8574a); - -/* Each client has this additional data */ -struct pcf8574_data { - int write; /* Remember last written value */ -}; - -static void pcf8574_init_client(struct i2c_client *client); - -/* following are the sysfs callback functions */ -static ssize_t show_read(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%u\n", i2c_smbus_read_byte(client)); -} - -static DEVICE_ATTR(read, S_IRUGO, show_read, NULL); - -static ssize_t show_write(struct device *dev, struct device_attribute *attr, char *buf) -{ - struct pcf8574_data *data = i2c_get_clientdata(to_i2c_client(dev)); - - if (data->write < 0) - return data->write; - - return sprintf(buf, "%d\n", data->write); -} - -static ssize_t set_write(struct device *dev, struct device_attribute *attr, const char *buf, - size_t count) -{ - struct i2c_client *client = to_i2c_client(dev); - struct pcf8574_data *data = i2c_get_clientdata(client); - unsigned long val = simple_strtoul(buf, NULL, 10); - - if (val > 0xff) - return -EINVAL; - - data->write = val; - i2c_smbus_write_byte(client, data->write); - return count; -} - -static DEVICE_ATTR(write, S_IWUSR | S_IRUGO, show_write, set_write); - -static struct attribute *pcf8574_attributes[] = { - &dev_attr_read.attr, - &dev_attr_write.attr, - NULL -}; - -static const struct attribute_group pcf8574_attr_group = { - .attrs = pcf8574_attributes, -}; - -/* - * Real code - */ - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pcf8574_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - const char *client_name; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) - return -ENODEV; - - /* Now, we would do the remaining detection. But the PCF8574 is plainly - impossible to detect! Stupid chip. */ - - /* Determine the chip type */ - if (kind <= 0) { - if (client->addr >= 0x38 && client->addr <= 0x3f) - kind = pcf8574a; - else - kind = pcf8574; - } - - if (kind == pcf8574a) - client_name = "pcf8574a"; - else - client_name = "pcf8574"; - strlcpy(info->type, client_name, I2C_NAME_SIZE); - - return 0; -} - -static int pcf8574_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct pcf8574_data *data; - int err; - - data = kzalloc(sizeof(struct pcf8574_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - i2c_set_clientdata(client, data); - - /* Initialize the PCF8574 chip */ - pcf8574_init_client(client); - - /* Register sysfs hooks */ - err = sysfs_create_group(&client->dev.kobj, &pcf8574_attr_group); - if (err) - goto exit_free; - return 0; - - exit_free: - kfree(data); - exit: - return err; -} - -static int pcf8574_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pcf8574_attr_group); - kfree(i2c_get_clientdata(client)); - return 0; -} - -/* Called when we have found a new PCF8574. */ -static void pcf8574_init_client(struct i2c_client *client) -{ - struct pcf8574_data *data = i2c_get_clientdata(client); - data->write = -EAGAIN; -} - -static const struct i2c_device_id pcf8574_id[] = { - { "pcf8574", 0 }, - { "pcf8574a", 0 }, - { } -}; - -static struct i2c_driver pcf8574_driver = { - .driver = { - .name = "pcf8574", - }, - .probe = pcf8574_probe, - .remove = pcf8574_remove, - .id_table = pcf8574_id, - - .detect = pcf8574_detect, - .address_data = &addr_data, -}; - -static int __init pcf8574_init(void) -{ - return i2c_add_driver(&pcf8574_driver); -} - -static void __exit pcf8574_exit(void) -{ - i2c_del_driver(&pcf8574_driver); -} - - -MODULE_AUTHOR - ("Frodo Looijaard , " - "Philip Edelbrock , " - "Dan Eaton " - "and Aurelien Jarno "); -MODULE_DESCRIPTION("PCF8574 driver"); -MODULE_LICENSE("GPL"); - -module_init(pcf8574_init); -module_exit(pcf8574_exit); -- cgit v1.2.3-59-g8ed1b From 76b3e28fa728bb68895cbd8375f5ce233bd891de Mon Sep 17 00:00:00 2001 From: Crane Cai Date: Fri, 18 Sep 2009 22:45:50 +0200 Subject: i2c-piix4: Add AMD SB900 SMBus device ID Add new SMBus device ID for AMD SB900. Signed-off-by: Crane Cai Signed-off-by: Jean Delvare --- Documentation/i2c/busses/i2c-piix4 | 2 ++ drivers/i2c/busses/Kconfig | 3 ++- drivers/i2c/busses/i2c-piix4.c | 9 ++++++--- include/linux/pci_ids.h | 1 + 4 files changed, 11 insertions(+), 4 deletions(-) (limited to 'Documentation') diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index f889481762b5..c5b37c570554 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -8,6 +8,8 @@ Supported adapters: Datasheet: Only available via NDA from ServerWorks * ATI IXP200, IXP300, IXP400, SB600, SB700 and SB800 southbridges Datasheet: Not publicly available + * AMD SB900 + Datasheet: Not publicly available * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge Datasheet: Publicly available at the SMSC website http://www.smsc.com diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 8206442fbabd..bb216c5fe30e 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -113,7 +113,7 @@ config I2C_ISCH will be called i2c-isch. config I2C_PIIX4 - tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)" + tristate "Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)" depends on PCI help If you say yes to this option, support will be included for the Intel @@ -128,6 +128,7 @@ config I2C_PIIX4 ATI SB600 ATI SB700 ATI SB800 + AMD SB900 Serverworks OSB4 Serverworks CSB5 Serverworks CSB6 diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index 0249a7d762b9..a782c7a08f9e 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -22,6 +22,7 @@ Intel PIIX4, 440MX Serverworks OSB4, CSB5, CSB6, HT-1000, HT-1100 ATI IXP200, IXP300, IXP400, SB600, SB700, SB800 + AMD SB900 SMSC Victory66 Note: we assume there can only be one device, with one SMBus interface. @@ -479,6 +480,7 @@ static struct pci_device_id piix4_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS) }, + { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_SB900_SMBUS) }, { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4) }, { PCI_DEVICE(PCI_VENDOR_ID_SERVERWORKS, @@ -499,9 +501,10 @@ static int __devinit piix4_probe(struct pci_dev *dev, { int retval; - if ((dev->vendor == PCI_VENDOR_ID_ATI) && - (dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS) && - (dev->revision >= 0x40)) + if ((dev->vendor == PCI_VENDOR_ID_ATI && + dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS && + dev->revision >= 0x40) || + dev->vendor == PCI_VENDOR_ID_AMD) /* base address location etc changed in SB800 */ retval = piix4_setup_sb800(dev, id); else diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 3b6b788fe2b5..7803565aa877 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -543,6 +543,7 @@ #define PCI_DEVICE_ID_AMD_8131_BRIDGE 0x7450 #define PCI_DEVICE_ID_AMD_8131_APIC 0x7451 #define PCI_DEVICE_ID_AMD_8132_BRIDGE 0x7458 +#define PCI_DEVICE_ID_AMD_SB900_SMBUS 0x780b #define PCI_DEVICE_ID_AMD_CS5535_IDE 0x208F #define PCI_DEVICE_ID_AMD_CS5536_ISA 0x2090 #define PCI_DEVICE_ID_AMD_CS5536_FLASH 0x2091 -- cgit v1.2.3-59-g8ed1b