From a36e9a1c5fa67cdc965fe011f1d04317adb35953 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Wed, 16 May 2012 22:17:38 +0200 Subject: GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio Implements OF support and convert to of_mm_gpio. By attaching hardware latches to the External Bus Unit (EBU) on Lantiq SoC, it is possible to create output only gpios. This driver configures a special memory address, which when written to, outputs 16 bit to the latches. Signed-off-by: John Crispin Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Acked-by: Grant Likely Patchwork: https://patchwork.linux-mips.org/patch/3840/ Signed-off-by: Ralf Baechle --- .../devicetree/bindings/gpio/gpio-mm-lantiq.txt | 38 ++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt new file mode 100644 index 000000000000..f93d51478d5a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt @@ -0,0 +1,38 @@ +Lantiq SoC External Bus memory mapped GPIO controller + +By attaching hardware latches to the EBU it is possible to create output +only gpios. This driver configures a special memory address, which when +written to outputs 16 bit to the latches. + +The node describing the memory mapped GPIOs needs to be a child of the node +describing the "lantiq,localbus". + +Required properties: +- compatible : Should be "lantiq,gpio-mm-lantiq" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. + +Example: + +localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + + gpio_mm0: gpio@4000000 { + compatible = "lantiq,gpio-mm"; + reg = <1 0x0 0x10>; + gpio-controller; + #gpio-cells = <2>; + lantiq,shadow = <0x77f> + }; +} -- cgit v1.2.3-59-g8ed1b From 54f30066178d4ff2da8e62427975736131cdbf96 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Wed, 16 May 2012 22:22:47 +0200 Subject: GPIO: MIPS: lantiq: convert gpio-stp-xway to OF Implements OF support and add code to load custom properties from the DT. The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a peripheral controller used to drive external shift register cascades. At most 3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem to drive the 2 LSBs of the cascade automatically. Newer socs are also able to automatically drive some pins via the internal PHYs. The driver currently only supports output functionality. Patches for the input feature found on newer generations of the soc will be provided in a later series. Signed-off-by: John Crispin Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Acked-by: Grant Likely Patchwork: https://patchwork.linux-mips.org/patch/3839/ Signed-off-by: Ralf Baechle --- .../devicetree/bindings/gpio/gpio-stp-xway.txt | 42 +++ drivers/gpio/gpio-stp-xway.c | 333 +++++++++++++++------ 2 files changed, 283 insertions(+), 92 deletions(-) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt new file mode 100644 index 000000000000..854de130a971 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt @@ -0,0 +1,42 @@ +Lantiq SoC Serial To Parallel (STP) GPIO controller + +The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a +peripheral controller used to drive external shift register cascades. At most +3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem +to drive the 2 LSBs of the cascade automatically. + + +Required properties: +- compatible : Should be "lantiq,gpio-stp-xway" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. +- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled + in the shift register cascade. +- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit + property can enable this feature. +- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade. +- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade. +- lantiq,rising : use rising instead of falling edge for the shift register + +Example: + +gpio1: stp@E100BB0 { + compatible = "lantiq,gpio-stp-xway"; + reg = <0xE100BB0 0x40>; + #gpio-cells = <2>; + gpio-controller; + + lantiq,shadow = <0xffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x3>; + lantiq,phy1 = <0x7>; + lantiq,phy2 = <0x7>; + /* lantiq,rising; */ +}; diff --git a/drivers/gpio/gpio-stp-xway.c b/drivers/gpio/gpio-stp-xway.c index d674f1be237d..e35096bf3cfb 100644 --- a/drivers/gpio/gpio-stp-xway.c +++ b/drivers/gpio/gpio-stp-xway.c @@ -3,150 +3,299 @@ * under the terms of the GNU General Public License version 2 as published * by the Free Software Foundation. * - * Copyright (C) 2007 John Crispin + * Copyright (C) 2012 John Crispin * */ #include #include -#include +#include #include -#include +#include #include -#include #include +#include +#include +#include +#include #include -#define LTQ_STP_CON0 0x00 -#define LTQ_STP_CON1 0x04 -#define LTQ_STP_CPU0 0x08 -#define LTQ_STP_CPU1 0x0C -#define LTQ_STP_AR 0x10 - -#define LTQ_STP_CON_SWU (1 << 31) -#define LTQ_STP_2HZ 0 -#define LTQ_STP_4HZ (1 << 23) -#define LTQ_STP_8HZ (2 << 23) -#define LTQ_STP_10HZ (3 << 23) -#define LTQ_STP_SPEED_MASK (0xf << 23) -#define LTQ_STP_UPD_FPI (1 << 31) -#define LTQ_STP_UPD_MASK (3 << 30) -#define LTQ_STP_ADSL_SRC (3 << 24) - -#define LTQ_STP_GROUP0 (1 << 0) - -#define LTQ_STP_RISING 0 -#define LTQ_STP_FALLING (1 << 26) -#define LTQ_STP_EDGE_MASK (1 << 26) - -#define ltq_stp_r32(reg) __raw_readl(ltq_stp_membase + reg) -#define ltq_stp_w32(val, reg) __raw_writel(val, ltq_stp_membase + reg) -#define ltq_stp_w32_mask(clear, set, reg) \ - ltq_w32((ltq_r32(ltq_stp_membase + reg) & ~(clear)) | (set), \ - ltq_stp_membase + (reg)) - -static int ltq_stp_shadow = 0xffff; -static void __iomem *ltq_stp_membase; - -static void ltq_stp_set(struct gpio_chip *chip, unsigned offset, int value) +/* + * The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a + * peripheral controller used to drive external shift register cascades. At most + * 3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem + * to drive the 2 LSBs of the cascade automatically. + */ + +/* control register 0 */ +#define XWAY_STP_CON0 0x00 +/* control register 1 */ +#define XWAY_STP_CON1 0x04 +/* data register 0 */ +#define XWAY_STP_CPU0 0x08 +/* data register 1 */ +#define XWAY_STP_CPU1 0x0C +/* access register */ +#define XWAY_STP_AR 0x10 + +/* software or hardware update select bit */ +#define XWAY_STP_CON_SWU BIT(31) + +/* automatic update rates */ +#define XWAY_STP_2HZ 0 +#define XWAY_STP_4HZ BIT(23) +#define XWAY_STP_8HZ BIT(24) +#define XWAY_STP_10HZ (BIT(24) | BIT(23)) +#define XWAY_STP_SPEED_MASK (0xf << 23) + +/* clock source for automatic update */ +#define XWAY_STP_UPD_FPI BIT(31) +#define XWAY_STP_UPD_MASK (BIT(31) | BIT(30)) + +/* let the adsl core drive the 2 LSBs */ +#define XWAY_STP_ADSL_SHIFT 24 +#define XWAY_STP_ADSL_MASK 0x3 + +/* 2 groups of 3 bits can be driven by the phys */ +#define XWAY_STP_PHY_MASK 0x3 +#define XWAY_STP_PHY1_SHIFT 27 +#define XWAY_STP_PHY2_SHIFT 15 + +/* STP has 3 groups of 8 bits */ +#define XWAY_STP_GROUP0 BIT(0) +#define XWAY_STP_GROUP1 BIT(1) +#define XWAY_STP_GROUP2 BIT(2) +#define XWAY_STP_GROUP_MASK (0x7) + +/* Edge configuration bits */ +#define XWAY_STP_FALLING BIT(26) +#define XWAY_STP_EDGE_MASK BIT(26) + +#define xway_stp_r32(m, reg) __raw_readl(m + reg) +#define xway_stp_w32(m, val, reg) __raw_writel(val, m + reg) +#define xway_stp_w32_mask(m, clear, set, reg) \ + ltq_w32((ltq_r32(m + reg) & ~(clear)) | (set), \ + m + reg) + +struct xway_stp { + struct gpio_chip gc; + void __iomem *virt; + u32 edge; /* rising or falling edge triggered shift register */ + u16 shadow; /* shadow the shift registers state */ + u8 groups; /* we can drive 1-3 groups of 8bit each */ + u8 dsl; /* the 2 LSBs can be driven by the dsl core */ + u8 phy1; /* 3 bits can be driven by phy1 */ + u8 phy2; /* 3 bits can be driven by phy2 */ + u8 reserved; /* mask out the hw driven bits in gpio_request */ +}; + +/** + * xway_stp_set() - gpio_chip->set - set gpios. + * @gc: Pointer to gpio_chip device structure. + * @gpio: GPIO signal number. + * @val: Value to be written to specified signal. + * + * Set the shadow value and call ltq_ebu_apply. + */ +static void xway_stp_set(struct gpio_chip *gc, unsigned gpio, int val) { - if (value) - ltq_stp_shadow |= (1 << offset); + struct xway_stp *chip = + container_of(gc, struct xway_stp, gc); + + if (val) + chip->shadow |= BIT(gpio); else - ltq_stp_shadow &= ~(1 << offset); - ltq_stp_w32(ltq_stp_shadow, LTQ_STP_CPU0); + chip->shadow &= ~BIT(gpio); + xway_stp_w32(chip->virt, chip->shadow, XWAY_STP_CPU0); + xway_stp_w32_mask(chip->virt, 0, XWAY_STP_CON_SWU, XWAY_STP_CON0); } -static int ltq_stp_direction_output(struct gpio_chip *chip, unsigned offset, - int value) +/** + * xway_stp_dir_out() - gpio_chip->dir_out - set gpio direction. + * @gc: Pointer to gpio_chip device structure. + * @gpio: GPIO signal number. + * @val: Value to be written to specified signal. + * + * Same as xway_stp_set, always returns 0. + */ +static int xway_stp_dir_out(struct gpio_chip *gc, unsigned gpio, int val) { - ltq_stp_set(chip, offset, value); + xway_stp_set(gc, gpio, val); return 0; } -static struct gpio_chip ltq_stp_chip = { - .label = "ltq_stp", - .direction_output = ltq_stp_direction_output, - .set = ltq_stp_set, - .base = 48, - .ngpio = 24, - .can_sleep = 1, - .owner = THIS_MODULE, -}; +/** + * xway_stp_request() - gpio_chip->request + * @gc: Pointer to gpio_chip device structure. + * @gpio: GPIO signal number. + * + * We mask out the HW driven pins + */ +static int xway_stp_request(struct gpio_chip *gc, unsigned gpio) +{ + struct xway_stp *chip = + container_of(gc, struct xway_stp, gc); + + if ((gpio < 8) && (chip->reserved & BIT(gpio))) { + dev_err(gc->dev, "GPIO %d is driven by hardware\n", gpio); + return -ENODEV; + } -static int ltq_stp_hw_init(void) + return 0; +} + +/** + * xway_stp_hw_init() - Configure the STP unit and enable the clock gate + * @virt: pointer to the remapped register range + */ +static int xway_stp_hw_init(struct xway_stp *chip) { /* sane defaults */ - ltq_stp_w32(0, LTQ_STP_AR); - ltq_stp_w32(0, LTQ_STP_CPU0); - ltq_stp_w32(0, LTQ_STP_CPU1); - ltq_stp_w32(LTQ_STP_CON_SWU, LTQ_STP_CON0); - ltq_stp_w32(0, LTQ_STP_CON1); + xway_stp_w32(chip->virt, 0, XWAY_STP_AR); + xway_stp_w32(chip->virt, 0, XWAY_STP_CPU0); + xway_stp_w32(chip->virt, 0, XWAY_STP_CPU1); + xway_stp_w32(chip->virt, XWAY_STP_CON_SWU, XWAY_STP_CON0); + xway_stp_w32(chip->virt, 0, XWAY_STP_CON1); - /* rising or falling edge */ - ltq_stp_w32_mask(LTQ_STP_EDGE_MASK, LTQ_STP_FALLING, LTQ_STP_CON0); + /* apply edge trigger settings for the shift register */ + xway_stp_w32_mask(chip->virt, XWAY_STP_EDGE_MASK, + chip->edge, XWAY_STP_CON0); - /* per default stp 15-0 are set */ - ltq_stp_w32_mask(0, LTQ_STP_GROUP0, LTQ_STP_CON1); + /* apply led group settings */ + xway_stp_w32_mask(chip->virt, XWAY_STP_GROUP_MASK, + chip->groups, XWAY_STP_CON1); - /* stp are update periodically by the FPI bus */ - ltq_stp_w32_mask(LTQ_STP_UPD_MASK, LTQ_STP_UPD_FPI, LTQ_STP_CON1); + /* tell the hardware which pins are controlled by the dsl modem */ + xway_stp_w32_mask(chip->virt, + XWAY_STP_ADSL_MASK << XWAY_STP_ADSL_SHIFT, + chip->dsl << XWAY_STP_ADSL_SHIFT, + XWAY_STP_CON0); - /* set stp update speed */ - ltq_stp_w32_mask(LTQ_STP_SPEED_MASK, LTQ_STP_8HZ, LTQ_STP_CON1); + /* tell the hardware which pins are controlled by the phys */ + xway_stp_w32_mask(chip->virt, + XWAY_STP_PHY_MASK << XWAY_STP_PHY1_SHIFT, + chip->phy1 << XWAY_STP_PHY1_SHIFT, + XWAY_STP_CON0); + xway_stp_w32_mask(chip->virt, + XWAY_STP_PHY_MASK << XWAY_STP_PHY2_SHIFT, + chip->phy2 << XWAY_STP_PHY2_SHIFT, + XWAY_STP_CON1); - /* tell the hardware that pin (led) 0 and 1 are controlled - * by the dsl arc + /* mask out the hw driven bits in gpio_request */ + chip->reserved = (chip->phy2 << 5) | (chip->phy1 << 2) | chip->dsl; + + /* + * if we have pins that are driven by hw, we need to tell the stp what + * clock to use as a timer. */ - ltq_stp_w32_mask(0, LTQ_STP_ADSL_SRC, LTQ_STP_CON0); + if (chip->reserved) + xway_stp_w32_mask(chip->virt, XWAY_STP_UPD_MASK, + XWAY_STP_UPD_FPI, XWAY_STP_CON1); - ltq_pmu_enable(PMU_LED); return 0; } -static int __devinit ltq_stp_probe(struct platform_device *pdev) +static int __devinit xway_stp_probe(struct platform_device *pdev) { struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + const __be32 *shadow, *groups, *dsl, *phy; + struct xway_stp *chip; + struct clk *clk; int ret = 0; - if (!res) - return -ENOENT; - res = devm_request_mem_region(&pdev->dev, res->start, - resource_size(res), dev_name(&pdev->dev)); if (!res) { - dev_err(&pdev->dev, "failed to request STP memory\n"); - return -EBUSY; + dev_err(&pdev->dev, "failed to request STP resource\n"); + return -ENOENT; } - ltq_stp_membase = devm_ioremap_nocache(&pdev->dev, res->start, - resource_size(res)); - if (!ltq_stp_membase) { + + chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->virt = devm_request_and_ioremap(&pdev->dev, res); + if (!chip->virt) { dev_err(&pdev->dev, "failed to remap STP memory\n"); return -ENOMEM; } - ret = gpiochip_add(<q_stp_chip); + chip->gc.dev = &pdev->dev; + chip->gc.label = "stp-xway"; + chip->gc.direction_output = xway_stp_dir_out; + chip->gc.set = xway_stp_set; + chip->gc.request = xway_stp_request; + chip->gc.base = -1; + chip->gc.owner = THIS_MODULE; + + /* store the shadow value if one was passed by the devicetree */ + shadow = of_get_property(pdev->dev.of_node, "lantiq,shadow", NULL); + if (shadow) + chip->shadow = be32_to_cpu(*shadow); + + /* find out which gpio groups should be enabled */ + groups = of_get_property(pdev->dev.of_node, "lantiq,groups", NULL); + if (groups) + chip->groups = be32_to_cpu(*groups) & XWAY_STP_GROUP_MASK; + else + chip->groups = XWAY_STP_GROUP0; + chip->gc.ngpio = fls(chip->groups) * 8; + + /* find out which gpios are controlled by the dsl core */ + dsl = of_get_property(pdev->dev.of_node, "lantiq,dsl", NULL); + if (dsl) + chip->dsl = be32_to_cpu(*dsl) & XWAY_STP_ADSL_MASK; + + /* find out which gpios are controlled by the phys */ + if (of_machine_is_compatible("lantiq,ar9") || + of_machine_is_compatible("lantiq,gr9") || + of_machine_is_compatible("lantiq,vr9")) { + phy = of_get_property(pdev->dev.of_node, "lantiq,phy1", NULL); + if (phy) + chip->phy1 = be32_to_cpu(*phy) & XWAY_STP_PHY_MASK; + phy = of_get_property(pdev->dev.of_node, "lantiq,phy2", NULL); + if (phy) + chip->phy2 = be32_to_cpu(*phy) & XWAY_STP_PHY_MASK; + } + + /* check which edge trigger we should use, default to a falling edge */ + if (!of_find_property(pdev->dev.of_node, "lantiq,rising", NULL)) + chip->edge = XWAY_STP_FALLING; + + clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "Failed to get clock\n"); + return PTR_ERR(clk); + } + clk_enable(clk); + + ret = xway_stp_hw_init(chip); if (!ret) - ret = ltq_stp_hw_init(); + ret = gpiochip_add(&chip->gc); + + if (!ret) + dev_info(&pdev->dev, "Init done\n"); return ret; } -static struct platform_driver ltq_stp_driver = { - .probe = ltq_stp_probe, +static const struct of_device_id xway_stp_match[] = { + { .compatible = "lantiq,gpio-stp-xway" }, + {}, +}; +MODULE_DEVICE_TABLE(of, xway_stp_match); + +static struct platform_driver xway_stp_driver = { + .probe = xway_stp_probe, .driver = { - .name = "ltq_stp", + .name = "gpio-stp-xway", .owner = THIS_MODULE, + .of_match_table = xway_stp_match, }, }; -int __init ltq_stp_init(void) +int __init xway_stp_init(void) { - int ret = platform_driver_register(<q_stp_driver); - - if (ret) - pr_info("ltq_stp: error registering platfom driver"); - return ret; + return platform_driver_register(&xway_stp_driver); } -postcore_initcall(ltq_stp_init); +subsys_initcall(xway_stp_init); -- cgit v1.2.3-59-g8ed1b