From 05ed60874e7fc958707183b71ea47260c1dab358 Mon Sep 17 00:00:00 2001
From: Victor Gallardo <vgallardo@apm.com>
Date: Fri, 8 Oct 2010 10:26:13 +0000
Subject: powerpc/4xx: Add Kilauea suspend and idle support

- Add Clock Power Management (CPM) node to dts tree
- Add idle-doze entry in CPM node
- Add standby entry in CPM node
- Add PM and SUSPEND support by default in defconfig
- Add NO_HZ and CONFIG_HIGH_RES_TIMERS support by
  default in defconfig

Signed-off-by: Victor Gallardo <vgallardo@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/boot/dts/kilauea.dts | 9 +++++++++
 1 file changed, 9 insertions(+)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/kilauea.dts b/arch/powerpc/boot/dts/kilauea.dts
index 083e68eeaca4..89edb16649c3 100644
--- a/arch/powerpc/boot/dts/kilauea.dts
+++ b/arch/powerpc/boot/dts/kilauea.dts
@@ -82,6 +82,15 @@
 		interrupt-parent = <&UIC0>;
 	};
 
+	CPM0: cpm {
+		compatible = "ibm,cpm";
+		dcr-access-method = "native";
+		dcr-reg = <0x0b0 0x003>;
+		unused-units = <0x00000000>;
+		idle-doze = <0x02000000>;
+		standby = <0xe3e74800>;
+	};
+
 	plb {
 		compatible = "ibm,plb-405ex", "ibm,plb4";
 		#address-cells = <1>;
-- 
cgit v1.2.3-59-g8ed1b


From ee2ffd8bbb2170f9b52fc8ff4aebe9702e0de651 Mon Sep 17 00:00:00 2001
From: Victor Gallardo <vgallardo@apm.com>
Date: Fri, 8 Oct 2010 10:25:44 +0000
Subject: powerpc/4xx: Add Canyonlands suspend and idle support

- Add Clock Power Management (CPM) node to dts tree
- Add idle-doze entry in CPM node
- Add standby entry in CPM node
- Add PM and SUSPEND support by default in defconfig
- Remove UART2 and UART3 as they are unused, this will
  allow CPM to put unused-units (UART2 and UART3) to sleep.

Signed-off-by: Victor Gallardo <vgallardo@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
---
 arch/powerpc/boot/dts/canyonlands.dts          | 31 ++++++++------------------
 arch/powerpc/configs/44x/canyonlands_defconfig |  3 +++
 2 files changed, 12 insertions(+), 22 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/canyonlands.dts b/arch/powerpc/boot/dts/canyonlands.dts
index a30370396250..5b27a4b74b79 100644
--- a/arch/powerpc/boot/dts/canyonlands.dts
+++ b/arch/powerpc/boot/dts/canyonlands.dts
@@ -105,6 +105,15 @@
 		dcr-reg = <0x00c 0x002>;
 	};
 
+	CPM0: cpm {
+		compatible = "ibm,cpm";
+		dcr-access-method = "native";
+		dcr-reg = <0x160 0x003>;
+		unused-units = <0x00000100>;
+		idle-doze = <0x02000000>;
+		standby = <0xfeff791d>;
+	};
+
 	L2C0: l2c {
 		compatible = "ibm,l2-cache-460ex", "ibm,l2-cache";
 		dcr-reg = <0x020 0x008		/* Internal SRAM DCR's */
@@ -270,28 +279,6 @@
 				interrupts = <0x1 0x4>;
 			};
 
-			UART2: serial@ef600500 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600500 0x00000008>;
-				virtual-reg = <0xef600500>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>; /* Filled in by U-Boot */
-				interrupt-parent = <&UIC1>;
-				interrupts = <28 0x4>;
-			};
-
-			UART3: serial@ef600600 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600600 0x00000008>;
-				virtual-reg = <0xef600600>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>; /* Filled in by U-Boot */
-				interrupt-parent = <&UIC1>;
-				interrupts = <29 0x4>;
-			};
-
 			IIC0: i2c@ef600700 {
 				compatible = "ibm,iic-460ex", "ibm,iic";
 				reg = <0xef600700 0x00000014>;
diff --git a/arch/powerpc/configs/44x/canyonlands_defconfig b/arch/powerpc/configs/44x/canyonlands_defconfig
index 45c64d818b2a..17e4dd98eed7 100644
--- a/arch/powerpc/configs/44x/canyonlands_defconfig
+++ b/arch/powerpc/configs/44x/canyonlands_defconfig
@@ -42,6 +42,9 @@ CONFIG_MTD_PHYSMAP_OF=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_NDFC=y
 CONFIG_PROC_DEVICETREE=y
+CONFIG_PM=y
+CONFIG_SUSPEND=y
+CONFIG_PPC4xx_CPM=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=35000
 # CONFIG_MISC_DEVICES is not set
-- 
cgit v1.2.3-59-g8ed1b


From 63849340621f7f5f963e4a9b9ba76add3ad54612 Mon Sep 17 00:00:00 2001
From: Dirk Brandewie <dirk.brandewie@gmail.com>
Date: Wed, 22 Dec 2010 11:57:28 -0800
Subject: of/powerpc: Use generic rule to build dtb's

Modify arch/powerpc/boot/Makefile to use dtc command in
scripts/Makefile.lib

Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/Makefile | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index fae8192c8fcc..96deec63bcf3 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -35,7 +35,7 @@ endif
 
 BOOTCFLAGS	+= -I$(obj) -I$(srctree)/$(obj)
 
-DTS_FLAGS	?= -p 1024
+DTC_FLAGS	?= -p 1024
 
 $(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
@@ -332,10 +332,8 @@ $(obj)/treeImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
 	$(call if_changed,wrap,treeboot-$*,,$(obj)/$*.dtb)
 
 # Rule to build device tree blobs
-DTC = $(objtree)/scripts/dtc/dtc
-
-$(obj)/%.dtb: $(dtstree)/%.dts
-	$(DTC) -O dtb -o $(obj)/$*.dtb -b 0 $(DTS_FLAGS) $(dtstree)/$*.dts
+$(obj)/%.dtb: $(src)/dts/%.dts
+	$(call cmd,dtc)
 
 # If there isn't a platform selected then just strip the vmlinux.
 ifeq (,$(image-y))
-- 
cgit v1.2.3-59-g8ed1b


From 55271024a735d0c3234e6ca7e0914b05aab7fbac Mon Sep 17 00:00:00 2001
From: Wolfram Sang <w.sang@pengutronix.de>
Date: Wed, 17 Nov 2010 13:00:50 +0100
Subject: powerpc/pcm{030,032}: add pagesize to dts

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/pcm030.dts | 1 +
 arch/powerpc/boot/dts/pcm032.dts | 3 ++-
 2 files changed, 3 insertions(+), 1 deletion(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts
index 8a4ec30b21ae..e7c36bc88fa0 100644
--- a/arch/powerpc/boot/dts/pcm030.dts
+++ b/arch/powerpc/boot/dts/pcm030.dts
@@ -259,6 +259,7 @@
 			eeprom@52 {
 				compatible = "catalyst,24c32";
 				reg = <0x52>;
+				pagesize = <32>;
 			};
 		};
 
diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts
index 85d857a5d46e..e175e2c601b5 100644
--- a/arch/powerpc/boot/dts/pcm032.dts
+++ b/arch/powerpc/boot/dts/pcm032.dts
@@ -257,8 +257,9 @@
 				reg = <0x51>;
 			};
 			eeprom@52 {
-				compatible = "at24,24c32";
+				compatible = "catalyst,24c32";
 				reg = <0x52>;
+				pagesize = <32>;
 			};
 		};
 
-- 
cgit v1.2.3-59-g8ed1b


From 9d6599441837fc375ce768160e3c6f2f74eb5348 Mon Sep 17 00:00:00 2001
From: Ilya Yanok <yanok@emcraft.com>
Date: Wed, 27 Oct 2010 01:52:59 +0200
Subject: powerpc/83xx: add DMA controller to mpc8308 device-tree node

MPC8308 has DMA controller compatible with mpc512x_dma driver. This
patch adds device-tree node to support DMA controller on MPC8308RDB
board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/mpc8308rdb.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/mpc8308rdb.dts b/arch/powerpc/boot/dts/mpc8308rdb.dts
index a97eb2db5a18..d3db02f98ddd 100644
--- a/arch/powerpc/boot/dts/mpc8308rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8308rdb.dts
@@ -265,6 +265,14 @@
 			interrupt-parent = < &ipic >;
 		};
 
+		dma@2c000 {
+			compatible = "fsl,mpc8308-dma", "fsl,mpc5121-dma";
+			reg = <0x2c000 0x1800>;
+			interrupts = <3 0x8
+					94 0x8>;
+			interrupt-parent = < &ipic >;
+		};
+
 	};
 
 	pci0: pcie@e0009000 {
-- 
cgit v1.2.3-59-g8ed1b


From c9de9333f5a860cab82052bce6ac28bcac9b2c26 Mon Sep 17 00:00:00 2001
From: Ilya Yanok <yanok@emcraft.com>
Date: Wed, 27 Oct 2010 01:53:00 +0200
Subject: powerpc/83xx: add mpc8308_p1m DMA controller device-tree node

MPC8308 has DMA controller compatible with mpc512x_dma driver. This
patch adds device-tree node to support DMA controller on MPC8308 P1M
board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/mpc8308_p1m.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/mpc8308_p1m.dts b/arch/powerpc/boot/dts/mpc8308_p1m.dts
index 05a76ccfd499..697b3f6b78bf 100644
--- a/arch/powerpc/boot/dts/mpc8308_p1m.dts
+++ b/arch/powerpc/boot/dts/mpc8308_p1m.dts
@@ -297,6 +297,14 @@
 			interrupt-parent = < &ipic >;
 		};
 
+		dma@2c000 {
+			compatible = "fsl,mpc8308-dma", "fsl,mpc5121-dma";
+			reg = <0x2c000 0x1800>;
+			interrupts = <3 0x8
+					94 0x8>;
+			interrupt-parent = < &ipic >;
+		};
+
 	};
 
 	pci0: pcie@e0009000 {
-- 
cgit v1.2.3-59-g8ed1b


From 6bd121e2d4dcabb145d390a7131ec83102dfb838 Mon Sep 17 00:00:00 2001
From: Grant Likely <grant.likely@secretlab.ca>
Date: Mon, 3 Jan 2011 14:06:17 -0700
Subject: powerpc/dts: fix syntax bugs in bluestone.dts

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/bluestone.dts | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/bluestone.dts b/arch/powerpc/boot/dts/bluestone.dts
index 9bb3d72c0e5a..2a56a0dbd1f7 100644
--- a/arch/powerpc/boot/dts/bluestone.dts
+++ b/arch/powerpc/boot/dts/bluestone.dts
@@ -33,7 +33,7 @@
 	aliases {
 		ethernet0 = &EMAC0;
 		serial0 = &UART0;
-		serial1 = &UART1;
+		//serial1 = &UART1; --gcl missing UART1 label
 	};
 
 	cpus {
@@ -52,7 +52,7 @@
 			d-cache-size = <32768>;
 			dcr-controller;
 			dcr-access-method = "native";
-			next-level-cache = <&L2C0>;
+			//next-level-cache = <&L2C0>; --gcl missing L2C0 label
 		};
 	};
 
@@ -142,7 +142,7 @@
 					/*RXEOB*/ 0x7 0x4
 					/*SERR*/  0x3 0x4
 					/*TXDE*/  0x4 0x4
-					/*RXDE*/  0x5 0x4
+					/*RXDE*/  0x5 0x4>;
 		};
 
 		POB0: opb {
@@ -182,7 +182,7 @@
 						reg = <0x001a0000 0x00060000>;
 					};
 				};
-			}
+			};
 
 			UART0: serial@ef600300 {
 				device_type = "serial";
-- 
cgit v1.2.3-59-g8ed1b


From abf1e27fbb4200a010b8fcb1be8cc02485744862 Mon Sep 17 00:00:00 2001
From: John Bonesio <bones@secretlab.ca>
Date: Wed, 17 Nov 2010 15:28:30 -0800
Subject: powerpc/5200: dts: rename nodes to prepare for refactoring dts files

This patch renames nodes in dts fils for MPC5200b files to prepare for
refactoring of these files later. When refactoring it will be easier to verify
the results if the node names aren't changing at the same time.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/cm5200.dts    |  8 ++++----
 arch/powerpc/boot/dts/digsy_mtc.dts |  6 +++---
 arch/powerpc/boot/dts/lite5200b.dts |  2 +-
 arch/powerpc/boot/dts/media5200.dts |  2 +-
 arch/powerpc/boot/dts/motionpro.dts | 10 +++++-----
 arch/powerpc/boot/dts/mucmc52.dts   |  6 +++---
 arch/powerpc/boot/dts/pcm030.dts    |  6 +++---
 arch/powerpc/boot/dts/pcm032.dts    |  6 +++---
 arch/powerpc/boot/dts/uc101.dts     |  6 +++---
 9 files changed, 26 insertions(+), 26 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index dd3860846f15..9369dcd00a5f 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -160,25 +160,25 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2000 {		// PSC1
+		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
 		};
 
-		serial@2200 {		// PSC2
+		psc@2200 {		// PSC2
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2200 0x100>;
 			interrupts = <2 2 0>;
 		};
 
-		serial@2400 {		// PSC3
+		psc@2400 {		// PSC3
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2400 0x100>;
 			interrupts = <2 3 0>;
 		};
 
-		serial@2c00 {		// PSC6
+		psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts
index 8e9be6bfe23e..f0592de71bb6 100644
--- a/arch/powerpc/boot/dts/digsy_mtc.dts
+++ b/arch/powerpc/boot/dts/digsy_mtc.dts
@@ -155,13 +155,13 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2600 {		// PSC4
+		psc@2600 {		// PSC4
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2600 0x100>;
 			interrupts = <2 11 0>;
 		};
 
-		serial@2800 {		// PSC5
+		psc@2800 {		// PSC5
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2800 0x100>;
 			interrupts = <2 12 0>;
@@ -217,7 +217,7 @@
 		};
 	};
 
-	lpb {
+	localbus {
 		compatible = "fsl,mpc5200b-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts
index 59702ace900f..a74b79084059 100644
--- a/arch/powerpc/boot/dts/lite5200b.dts
+++ b/arch/powerpc/boot/dts/lite5200b.dts
@@ -172,7 +172,7 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2000 {		// PSC1
+		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <0>;
 			reg = <0x2000 0x100>;
diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
index 0c3902bc5b6a..a70ef680f301 100644
--- a/arch/powerpc/boot/dts/media5200.dts
+++ b/arch/powerpc/boot/dts/media5200.dts
@@ -183,7 +183,7 @@
 		};
 
 		// PSC6 in uart mode
-		console: serial@2c00 {		// PSC6
+		console: psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <5>;
 			port-number = <0>;  // Logical port assignment
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index 6ca4fc144a33..f6261ea0972b 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -100,7 +100,7 @@
 			interrupts = <1 14 0>;
 		};
 
-		motionpro-led@660 {	// Motion-PRO status LED
+		timer@660 {	// Motion-PRO status LED
 			compatible = "promess,motionpro-led";
 			label = "motionpro-statusled";
 			reg = <0x660 0x10>;
@@ -108,7 +108,7 @@
 			blink-delay = <100>; // 100 msec
 		};
 
-		motionpro-led@670 {	// Motion-PRO ready LED
+		timer@670 {	// Motion-PRO ready LED
 			compatible = "promess,motionpro-led";
 			label = "motionpro-readyled";
 			reg = <0x670 0x10>;
@@ -169,14 +169,14 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2000 {		// PSC1
+		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
 		};
 
 		// PSC2 in spi master mode 
-		spi@2200 {		// PSC2
+		psc@2200 {		// PSC2
 			compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
 			cell-index = <1>;
 			reg = <0x2200 0x100>;
@@ -184,7 +184,7 @@
 		};
 
 		// PSC5 in uart mode
-		serial@2800 {		// PSC5
+		psc@2800 {		// PSC5
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2800 0x100>;
 			interrupts = <2 12 0>;
diff --git a/arch/powerpc/boot/dts/mucmc52.dts b/arch/powerpc/boot/dts/mucmc52.dts
index b72a7581d798..8dc212d9238b 100644
--- a/arch/powerpc/boot/dts/mucmc52.dts
+++ b/arch/powerpc/boot/dts/mucmc52.dts
@@ -126,19 +126,19 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2000 { /* PSC1 in UART mode */
+		psc@2000 { /* PSC1 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
 		};
 
-		serial@2200 { /* PSC2 in UART mode */
+		psc@2200 { /* PSC2 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2200 0x100>;
 			interrupts = <2 2 0>;
 		};
 
-		serial@2c00 { /* PSC6 in UART mode */
+		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts
index e7c36bc88fa0..34ab3bbcf990 100644
--- a/arch/powerpc/boot/dts/pcm030.dts
+++ b/arch/powerpc/boot/dts/pcm030.dts
@@ -185,7 +185,7 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		ac97@2000 { /* PSC1 in ac97 mode */
+		psc@2000 { /* PSC1 in ac97 mode */
 			compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97";
 			cell-index = <0>;
 			reg = <0x2000 0x100>;
@@ -194,7 +194,7 @@
 
 		/* PSC2 port is used by CAN1/2 */
 
-		serial@2400 { /* PSC3 in UART mode */
+		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <2>;
 			reg = <0x2400 0x100>;
@@ -205,7 +205,7 @@
 
 		/* PSC5 is ??? */
 
-		serial@2c00 { /* PSC6 in UART mode */
+		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <5>;
 			reg = <0x2c00 0x100>;
diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts
index e175e2c601b5..29fde83b99b3 100644
--- a/arch/powerpc/boot/dts/pcm032.dts
+++ b/arch/powerpc/boot/dts/pcm032.dts
@@ -185,7 +185,7 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		ac97@2000 {	/* PSC1 is ac97 */
+		psc@2000 {	/* PSC1 is ac97 */
 			compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
 			cell-index = <0>;
 			reg = <0x2000 0x100>;
@@ -194,7 +194,7 @@
 
 		/* PSC2 port is used by CAN1/2 */
 
-		serial@2400 { /* PSC3 in UART mode */
+		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <2>;
 			reg = <0x2400 0x100>;
@@ -205,7 +205,7 @@
 
 		/* PSC5 is ??? */
 
-		serial@2c00 { /* PSC6 in UART mode */
+		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			cell-index = <5>;
 			reg = <0x2c00 0x100>;
diff --git a/arch/powerpc/boot/dts/uc101.dts b/arch/powerpc/boot/dts/uc101.dts
index 019264c62904..e00441a3e5a7 100644
--- a/arch/powerpc/boot/dts/uc101.dts
+++ b/arch/powerpc/boot/dts/uc101.dts
@@ -158,19 +158,19 @@
 			reg = <0x1f00 0x100>;
 		};
 
-		serial@2000 { /* PSC1 in UART mode */
+		psc@2000 { /* PSC1 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
 		};
 
-		serial@2200 { /* PSC2 in UART mode */
+		psc@2200 { /* PSC2 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2200 0x100>;
 			interrupts = <2 2 0>;
 		};
 
-		serial@2c00 {		/* PSC6 in UART mode */
+		psc@2c00 {		/* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
-- 
cgit v1.2.3-59-g8ed1b


From 6847317377c871c6e7a8d54e5849bcd0f9b11eb4 Mon Sep 17 00:00:00 2001
From: John Bonesio <bones@secretlab.ca>
Date: Wed, 17 Nov 2010 15:28:39 -0800
Subject: powerpc/5200: dts: remove unused properties

This patch remove unused properties in dts files in preparation of refactoring
the dts files for MPC5200b based boards.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/cm5200.dts    | 2 --
 arch/powerpc/boot/dts/lite5200b.dts | 3 ---
 arch/powerpc/boot/dts/media5200.dts | 2 --
 arch/powerpc/boot/dts/motionpro.dts | 2 --
 arch/powerpc/boot/dts/pcm030.dts    | 2 --
 arch/powerpc/boot/dts/pcm032.dts    | 2 --
 6 files changed, 13 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index 9369dcd00a5f..d549897b7eb3 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -230,8 +230,6 @@
 			reg = <0 0 0x2000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			#size-cells = <1>;
-			#address-cells = <1>;
 		};
 	};
 };
diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts
index a74b79084059..c0a4e4592baa 100644
--- a/arch/powerpc/boot/dts/lite5200b.dts
+++ b/arch/powerpc/boot/dts/lite5200b.dts
@@ -174,7 +174,6 @@
 
 		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <0>;
 			reg = <0x2000 0x100>;
 			interrupts = <2 1 0>;
 		};
@@ -198,7 +197,6 @@
 		// PSC4 in uart mode example
 		//serial@2600 {		// PSC4
 		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-		//	cell-index = <3>;
 		//	reg = <0x2600 0x100>;
 		//	interrupts = <2 11 0>;
 		//};
@@ -206,7 +204,6 @@
 		// PSC5 in uart mode example
 		//serial@2800 {		// PSC5
 		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-		//	cell-index = <4>;
 		//	reg = <0x2800 0x100>;
 		//	interrupts = <2 12 0>;
 		//};
diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
index a70ef680f301..e027f459c230 100644
--- a/arch/powerpc/boot/dts/media5200.dts
+++ b/arch/powerpc/boot/dts/media5200.dts
@@ -185,8 +185,6 @@
 		// PSC6 in uart mode
 		console: psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <5>;
-			port-number = <0>;  // Logical port assignment
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
 		};
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index f6261ea0972b..3ab4666c9944 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -277,8 +277,6 @@
 			reg = <0 0 0x01000000>;
 			bank-width = <2>;
 			device-width = <2>;
-			#size-cells = <1>;
-			#address-cells = <1>;
 		};
 	};
 };
diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts
index 34ab3bbcf990..28d77758d8be 100644
--- a/arch/powerpc/boot/dts/pcm030.dts
+++ b/arch/powerpc/boot/dts/pcm030.dts
@@ -196,7 +196,6 @@
 
 		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <2>;
 			reg = <0x2400 0x100>;
 			interrupts = <2 3 0>;
 		};
@@ -207,7 +206,6 @@
 
 		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <5>;
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
 		};
diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts
index 29fde83b99b3..9dee52b67477 100644
--- a/arch/powerpc/boot/dts/pcm032.dts
+++ b/arch/powerpc/boot/dts/pcm032.dts
@@ -196,7 +196,6 @@
 
 		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <2>;
 			reg = <0x2400 0x100>;
 			interrupts = <2 3 0>;
 		};
@@ -207,7 +206,6 @@
 
 		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			cell-index = <5>;
 			reg = <0x2c00 0x100>;
 			interrupts = <2 4 0>;
 		};
-- 
cgit v1.2.3-59-g8ed1b


From 11946c826d02a16521edc777d88470a6a0fe1441 Mon Sep 17 00:00:00 2001
From: John Bonesio <bones@secretlab.ca>
Date: Wed, 17 Nov 2010 15:28:47 -0800
Subject: powerpc/5200: dts: Change combatible strings on localbus

This patch changes some incorrect compatible strings on the local plus bus node
in dts files for MPC5200b based systems.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/cm5200.dts    | 2 +-
 arch/powerpc/boot/dts/digsy_mtc.dts | 2 +-
 arch/powerpc/boot/dts/media5200.dts | 2 +-
 arch/powerpc/boot/dts/motionpro.dts | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index d549897b7eb3..22f7233414ba 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -219,7 +219,7 @@
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","simple-bus";
+		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0xfc000000 0x2000000>;
diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts
index f0592de71bb6..3147b9894205 100644
--- a/arch/powerpc/boot/dts/digsy_mtc.dts
+++ b/arch/powerpc/boot/dts/digsy_mtc.dts
@@ -218,7 +218,7 @@
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","simple-bus";
+		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0xff000000 0x1000000>;
diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
index e027f459c230..861f09ff3a7f 100644
--- a/arch/powerpc/boot/dts/media5200.dts
+++ b/arch/powerpc/boot/dts/media5200.dts
@@ -270,7 +270,7 @@
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","simple-bus";
+		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index 3ab4666c9944..97cb08598a4a 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -236,7 +236,7 @@
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","simple-bus";
+		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0xff000000 0x01000000
-- 
cgit v1.2.3-59-g8ed1b


From c8bf6b52af670496f1e8145600e74a3ef3942a4c Mon Sep 17 00:00:00 2001
From: John Bonesio <bones@secretlab.ca>
Date: Wed, 17 Nov 2010 15:28:56 -0800
Subject: powerpc/5200: dts: refactor dts files

This patch creates mpc5200b.dtsi containing the information for the MPC5200b
SoC then modifies all of the dts files for MPC5200b based systems to use
mpc5200b.dtsi.

Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/cm5200.dts    | 192 ++++---------------------
 arch/powerpc/boot/dts/digsy_mtc.dts | 173 +++--------------------
 arch/powerpc/boot/dts/lite5200b.dts | 217 ++--------------------------
 arch/powerpc/boot/dts/media5200.dts | 210 +++------------------------
 arch/powerpc/boot/dts/motionpro.dts | 190 ++++---------------------
 arch/powerpc/boot/dts/mpc5200b.dtsi | 275 ++++++++++++++++++++++++++++++++++++
 arch/powerpc/boot/dts/mucmc52.dts   | 174 ++++++-----------------
 arch/powerpc/boot/dts/pcm030.dts    | 187 ++----------------------
 arch/powerpc/boot/dts/pcm032.dts    | 231 ++++--------------------------
 arch/powerpc/boot/dts/uc101.dts     | 160 +++++----------------
 10 files changed, 506 insertions(+), 1503 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/mpc5200b.dtsi

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index 22f7233414ba..ad3a4f4a2b04 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -10,226 +10,82 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "schindler,cm5200";
 	compatible = "schindler,cm5200";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;		// L1, 16K
-			i-cache-size = <0x4000>;		// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x04000000>;	// 64MB
-	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
-		timer@660 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
-		};
-
-		timer@670 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
+		can@900 {
+			status = "disabled";
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		can@980 {
+			status = "disabled";
 		};
 
 		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
 		psc@2200 {		// PSC2
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2200 0x100>;
-			interrupts = <2 2 0>;
 		};
 
 		psc@2400 {		// PSC3
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2400 0x100>;
-			interrupts = <2 3 0>;
+		};
+
+		psc@2600 {		// PSC4
+			status = "disabled";
+		};
+
+		psc@2800 {		// PSC5
+			status = "disabled";
 		};
 
 		psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
+		ata@3a00 {
+			status = "disabled";
 		};
 
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
+		i2c@3d00 {
+			status = "disabled";
 		};
+
 	};
 
-	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0xfc000000 0x2000000>;
+	pci@f0000d00 {
+		status = "disabled";
+	};
 
+	localbus {
 		// 16-bit flash device at LocalPlus Bus CS0
 		flash@0,0 {
 			compatible = "cfi-flash";
 			reg = <0 0 0x2000000>;
 			bank-width = <2>;
 			device-width = <2>;
+			#size-cells = <1>;
+			#address-cells = <1>;
 		};
 	};
 };
diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts
index 3147b9894205..27bd267d631c 100644
--- a/arch/powerpc/boot/dts/digsy_mtc.dts
+++ b/arch/powerpc/boot/dts/digsy_mtc.dts
@@ -11,195 +11,68 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "intercontrol,digsy-mtc";
 	compatible = "intercontrol,digsy-mtc";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;		// L1, 16K
-			i-cache-size = <0x4000>;		// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
 
 	memory {
-		device_type = "memory";
 		reg = <0x00000000 0x02000000>;	// 32MB
 	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
-		timer@660 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
-		};
-
-		timer@670 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		rtc@800 {
+			status = "disabled";
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		can@900 {
+			status = "disabled";
 		};
 
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
+		can@980 {
+			status = "disabled";
 		};
 
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
+		psc@2000 {		// PSC1
+			status = "disabled";
 		};
 
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
+		psc@2200 {		// PSC2
+			status = "disabled";
 		};
 
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		psc@2400 {		// PSC3
+			status = "disabled";
 		};
 
 		psc@2600 {		// PSC4
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2600 0x100>;
-			interrupts = <2 11 0>;
 		};
 
 		psc@2800 {		// PSC5
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2800 0x100>;
-			interrupts = <2 12 0>;
+		};
+
+		psc@2c00 {		// PSC6
+			status = "disabled";
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
 		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-
 			rtc@50 {
 				compatible = "at,24c08";
 				reg = <0x50>;
@@ -211,16 +84,16 @@
 			};
 		};
 
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
+		i2c@3d40 {
+			status = "disabled";
 		};
 	};
 
+	pci@f0000d00 {
+		status = "disabled";
+	};
+
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
 		ranges = <0 0 0xff000000 0x1000000>;
 
 		// 16-bit flash device at LocalPlus Bus CS0
diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts
index c0a4e4592baa..fb288bb882b6 100644
--- a/arch/powerpc/boot/dts/lite5200b.dts
+++ b/arch/powerpc/boot/dts/lite5200b.dts
@@ -10,253 +10,75 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "fsl,lite5200b";
 	compatible = "fsl,lite5200b";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
 
 	memory {
-		device_type = "memory";
 		reg = <0x00000000 0x10000000>;	// 256MB
 	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
-		timer@660 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
-		};
-
-		timer@670 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@900 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 17 0>;
-			reg = <0x900 0x80>;
-		};
-
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
-		};
-
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		psc@2000 {		// PSC1
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+			cell-index = <0>;
 		};
 
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
+		psc@2200 {		// PSC2
+			status = "disabled";
 		};
 
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
+		psc@2400 {		// PSC3
+			status = "disabled";
 		};
 
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
+		psc@2600 {		// PSC4
+			status = "disabled";
 		};
 
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		psc@2800 {		// PSC5
+			status = "disabled";
 		};
 
-		psc@2000 {		// PSC1
-			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
+		psc@2c00 {		// PSC6
+			status = "disabled";
 		};
 
 		// PSC2 in ac97 mode example
 		//ac97@2200 {		// PSC2
 		//	compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
 		//	cell-index = <1>;
-		//	reg = <0x2200 0x100>;
-		//	interrupts = <2 2 0>;
 		//};
 
 		// PSC3 in CODEC mode example
 		//i2s@2400 {		// PSC3
 		//	compatible = "fsl,mpc5200b-psc-i2s"; //not 5200 compatible
 		//	cell-index = <2>;
-		//	reg = <0x2400 0x100>;
-		//	interrupts = <2 3 0>;
-		//};
-
-		// PSC4 in uart mode example
-		//serial@2600 {		// PSC4
-		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-		//	reg = <0x2600 0x100>;
-		//	interrupts = <2 11 0>;
-		//};
-
-		// PSC5 in uart mode example
-		//serial@2800 {		// PSC5
-		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-		//	reg = <0x2800 0x100>;
-		//	interrupts = <2 12 0>;
 		//};
 
 		// PSC6 in spi mode example
 		//spi@2c00 {		// PSC6
 		//	compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
 		//	cell-index = <5>;
-		//	reg = <0x2c00 0x100>;
-		//	interrupts = <2 4 0>;
 		//};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
-		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-		};
-
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
-
 			eeprom@50 {
 				compatible = "atmel,24c02";
 				reg = <0x50>;
@@ -270,12 +92,6 @@
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
 				 0xc000 0 0 2 &mpc5200_pic 1 1 3
@@ -295,11 +111,6 @@
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = <0 0 0xfe000000 0x02000000>;
 
 		flash@0,0 {
diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts
index 861f09ff3a7f..48d72f38e5ed 100644
--- a/arch/powerpc/boot/dts/media5200.dts
+++ b/arch/powerpc/boot/dts/media5200.dts
@@ -11,14 +11,11 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "fsl,media5200";
 	compatible = "fsl,media5200";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
 
 	aliases {
 		console = &console;
@@ -30,16 +27,7 @@
 	};
 
 	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;		// L1, 16K
-			i-cache-size = <0x4000>;		// L1, 16K
 			timebase-frequency = <33000000>;	// 33 MHz, these were configured by U-Boot
 			bus-frequency = <132000000>;		// 132 MHz
 			clock-frequency = <396000000>;		// 396 MHz
@@ -47,203 +35,57 @@
 	};
 
 	memory {
-		device_type = "memory";
 		reg = <0x00000000 0x08000000>;	// 128MB RAM
 	};
 
-	soc@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
+	soc5200@f0000000 {
 		bus-frequency = <132000000>;// 132 MHz
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
 
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
-		timer@660 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
-		};
-
-		timer@670 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@900 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 17 0>;
-			reg = <0x900 0x80>;
+		psc@2000 {	// PSC1
+			status = "disabled";
 		};
 
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
+		psc@2200 {	// PSC2
+			status = "disabled";
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		psc@2400 {	// PSC3
+			status = "disabled";
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		psc@2600 {	// PSC4
+			status = "disabled";
 		};
 
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0x100>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		psc@2800 {	// PSC5
+			status = "disabled";
 		};
 
 		// PSC6 in uart mode
 		console: psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
-		eth0: ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
+		ethernet@3000 {
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
-		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-		};
-
-		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
-		};
-
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
+		usb@1000 {
+			reg = <0x1000 0x100>;
 		};
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <0xc000 0 0 1 &media5200_fpga 0 2 // 1st slot
 				 0xc000 0 0 2 &media5200_fpga 0 3
@@ -260,37 +102,29 @@
 
 				 0xe000 0 0 1 &media5200_fpga 0 5 // CoralIP
 				>;
-		clock-frequency = <0>; // From boot loader
-		interrupts = <2 8 0 2 9 0 2 10 0>;
-		interrupt-parent = <&mpc5200_pic>;
-		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
 			  0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
 			  0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
+		interrupt-parent = <&mpc5200_pic>;
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = < 0 0 0xfc000000 0x02000000
 			   1 0 0xfe000000 0x02000000
 			   2 0 0xf0010000 0x00010000
 			   3 0 0xf0020000 0x00010000 >;
-
 		flash@0,0 {
 			compatible = "amd,am29lv28ml", "cfi-flash";
-			reg = <0 0x0 0x2000000>;		// 32 MB
-			bank-width = <4>;			// Width in bytes of the flash bank
-			device-width = <2>;			// Two devices on each bank
+			reg = <0 0x0 0x2000000>;                // 32 MB
+			bank-width = <4>;                       // Width in bytes of the flash bank
+			device-width = <2>;                     // Two devices on each bank
 		};
 
 		flash@1,0 {
 			compatible = "amd,am29lv28ml", "cfi-flash";
-			reg = <1 0 0x2000000>;			// 32 MB
-			bank-width = <4>;			// Width in bytes of the flash bank
-			device-width = <2>;			// Two devices on each bank
+			reg = <1 0 0x2000000>;                  // 32 MB
+			bank-width = <4>;                       // Width in bytes of the flash bank
+			device-width = <2>;                     // Two devices on each bank
 		};
 
 		media5200_fpga: fpga@2,0 {
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index 97cb08598a4a..0b78e89ac69b 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -10,219 +10,73 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "promess,motionpro";
 	compatible = "promess,motionpro";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x04000000>;	// 64MB
-	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
-		timer@620 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
-		};
-
-		timer@630 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
-		};
-
-		timer@640 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
-		};
-
-		timer@650 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
-		};
-
 		timer@660 {	// Motion-PRO status LED
 			compatible = "promess,motionpro-led";
 			label = "motionpro-statusled";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
 			blink-delay = <100>; // 100 msec
 		};
 
 		timer@670 {	// Motion-PRO ready LED
 			compatible = "promess,motionpro-led";
 			label = "motionpro-readyled";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		can@900 {
+			status = "disabled";
 		};
 
 		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
 		// PSC2 in spi master mode 
 		psc@2200 {		// PSC2
 			compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
 			cell-index = <1>;
-			reg = <0x2200 0x100>;
-			interrupts = <2 2 0>;
 		};
 
-		// PSC5 in uart mode
+		psc@2400 {		// PSC3
+			status = "disabled";
+		};
+
+		psc@2600 {		// PSC4
+			status = "disabled";
+		};
+
 		psc@2800 {		// PSC5
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2800 0x100>;
-			interrupts = <2 12 0>;
+		};
+
+		psc@2c00 {		// PSC6
+			status = "disabled";
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@2 {
 				reg = <2>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
+		i2c@3d00 {
+			status = "disabled";
 		};
 
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
-
 			rtc@68 {
 				compatible = "dallas,ds1339";
 				reg = <0x68>;
@@ -235,10 +89,11 @@
 		};
 	};
 
+	pci@f0000d00 {
+		status = "disabled";
+	};
+
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
 		ranges = <0 0 0xff000000 0x01000000
 			  1 0 0x50000000 0x00010000
 			  2 0 0x50010000 0x00010000
@@ -277,6 +132,9 @@
 			reg = <0 0 0x01000000>;
 			bank-width = <2>;
 			device-width = <2>;
+			#size-cells = <1>;
+			#address-cells = <1>;
 		};
+
 	};
 };
diff --git a/arch/powerpc/boot/dts/mpc5200b.dtsi b/arch/powerpc/boot/dts/mpc5200b.dtsi
new file mode 100644
index 000000000000..bc27548e895d
--- /dev/null
+++ b/arch/powerpc/boot/dts/mpc5200b.dtsi
@@ -0,0 +1,275 @@
+/*
+ * base MPC5200b Device Tree Source
+ *
+ * Copyright (C) 2010 SecretLab
+ * Grant Likely <grant@secretlab.ca>
+ * John Bonesio <bones@secretlab.ca>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	model = "fsl,mpc5200b";
+	compatible = "fsl,mpc5200b";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&mpc5200_pic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		powerpc: PowerPC,5200@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <32>;
+			i-cache-line-size = <32>;
+			d-cache-size = <0x4000>;	// L1, 16K
+			i-cache-size = <0x4000>;	// L1, 16K
+			timebase-frequency = <0>;	// from bootloader
+			bus-frequency = <0>;		// from bootloader
+			clock-frequency = <0>;		// from bootloader
+		};
+	};
+
+	memory: memory {
+		device_type = "memory";
+		reg = <0x00000000 0x04000000>;	// 64MB
+	};
+
+	soc: soc5200@f0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc5200b-immr";
+		ranges = <0 0xf0000000 0x0000c000>;
+		reg = <0xf0000000 0x00000100>;
+		bus-frequency = <0>;		// from bootloader
+		system-frequency = <0>;		// from bootloader
+
+		cdm@200 {
+			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
+			reg = <0x200 0x38>;
+		};
+
+		mpc5200_pic: interrupt-controller@500 {
+			// 5200 interrupts are encoded into two levels;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
+			reg = <0x500 0x80>;
+		};
+
+		timer@600 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x600 0x10>;
+			interrupts = <1 9 0>;
+		};
+
+		timer@610 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x610 0x10>;
+			interrupts = <1 10 0>;
+		};
+
+		timer@620 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x620 0x10>;
+			interrupts = <1 11 0>;
+		};
+
+		timer@630 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x630 0x10>;
+			interrupts = <1 12 0>;
+		};
+
+		timer@640 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x640 0x10>;
+			interrupts = <1 13 0>;
+		};
+
+		timer@650 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x650 0x10>;
+			interrupts = <1 14 0>;
+		};
+
+		timer@660 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x660 0x10>;
+			interrupts = <1 15 0>;
+		};
+
+		timer@670 {	// General Purpose Timer
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x670 0x10>;
+			interrupts = <1 16 0>;
+		};
+
+		rtc@800 {	// Real time clock
+			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
+			reg = <0x800 0x100>;
+			interrupts = <1 5 0 1 6 0>;
+		};
+
+		can@900 {
+			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
+			interrupts = <2 17 0>;
+			reg = <0x900 0x80>;
+		};
+
+		can@980 {
+			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
+			interrupts = <2 18 0>;
+			reg = <0x980 0x80>;
+		};
+
+		gpio_simple: gpio@b00 {
+			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
+			reg = <0xb00 0x40>;
+			interrupts = <1 7 0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpio_wkup: gpio@c00 {
+			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
+			reg = <0xc00 0x40>;
+			interrupts = <1 8 0 0 3 0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		spi@f00 {
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+			reg = <0xf00 0x20>;
+			interrupts = <2 13 0 2 14 0>;
+		};
+
+		usb: usb@1000 {
+			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
+			reg = <0x1000 0xff>;
+			interrupts = <2 6 0>;
+		};
+
+		dma-controller@1200 {
+			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
+			reg = <0x1200 0x80>;
+			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
+			              3 4 0  3 5 0  3 6 0  3 7 0
+			              3 8 0  3 9 0  3 10 0  3 11 0
+			              3 12 0  3 13 0  3 14 0  3 15 0>;
+		};
+
+		xlb@1f00 {
+			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
+			reg = <0x1f00 0x100>;
+		};
+
+		psc1: psc@2000 {		// PSC1
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2000 0x100>;
+			interrupts = <2 1 0>;
+		};
+
+		psc2: psc@2200 {		// PSC2
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2200 0x100>;
+			interrupts = <2 2 0>;
+		};
+
+		psc3: psc@2400 {		// PSC3
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2400 0x100>;
+			interrupts = <2 3 0>;
+		};
+
+		psc4: psc@2600 {		// PSC4
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2600 0x100>;
+			interrupts = <2 11 0>;
+		};
+
+		psc5: psc@2800 {		// PSC5
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2800 0x100>;
+			interrupts = <2 12 0>;
+		};
+
+		psc6: psc@2c00 {		// PSC6
+			compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc";
+			reg = <0x2c00 0x100>;
+			interrupts = <2 4 0>;
+		};
+
+		eth0: ethernet@3000 {
+			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
+			reg = <0x3000 0x400>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <2 5 0>;
+		};
+
+		mdio@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
+			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
+		};
+
+		ata@3a00 {
+			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
+			reg = <0x3a00 0x100>;
+			interrupts = <2 7 0>;
+		};
+
+		i2c@3d00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+			reg = <0x3d00 0x40>;
+			interrupts = <2 15 0>;
+		};
+
+		i2c@3d40 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+			reg = <0x3d40 0x40>;
+			interrupts = <2 16 0>;
+		};
+
+		sram@8000 {
+			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
+			reg = <0x8000 0x4000>;
+		};
+	};
+
+	pci: pci@f0000d00 {
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
+		reg = <0xf0000d00 0x100>;
+		// interrupt-map-mask = need to add
+		// interrupt-map = need to add
+		clock-frequency = <0>; // From boot loader
+		interrupts = <2 8 0 2 9 0 2 10 0>;
+		bus-range = <0 0>;
+		// ranges = need to add
+	};
+
+	localbus: localbus {
+		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0xfc000000 0x2000000>;
+	};
+};
diff --git a/arch/powerpc/boot/dts/mucmc52.dts b/arch/powerpc/boot/dts/mucmc52.dts
index 8dc212d9238b..21d34720fcc9 100644
--- a/arch/powerpc/boot/dts/mucmc52.dts
+++ b/arch/powerpc/boot/dts/mucmc52.dts
@@ -11,172 +11,109 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "manroland,mucmc52";
 	compatible = "manroland,mucmc52";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x04000000>;	// 64MB
-	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		gpt0: timer@600 {	// GPT 0 in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt1: timer@610 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt2: timer@620 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt3: timer@630 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		timer@640 {
+			status = "disabled";
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		timer@650 {
+			status = "disabled";
+		};
+
+		timer@660 {
+			status = "disabled";
+		};
+
+		timer@670 {
+			status = "disabled";
 		};
 
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
+		rtc@800 {
+			status = "disabled";
 		};
 
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		can@900 {
+			status = "disabled";
 		};
 
-		psc@2000 { /* PSC1 in UART mode */
+		can@980 {
+			status = "disabled";
+		};
+
+		spi@f00 {
+			status = "disabled";
+		};
+
+		usb@1000 {
+			status = "disabled";
+		};
+
+		psc@2000 {		// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
-		psc@2200 { /* PSC2 in UART mode */
+		psc@2200 {		// PSC2
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2200 0x100>;
-			interrupts = <2 2 0>;
 		};
 
-		psc@2c00 { /* PSC6 in UART mode */
+		psc@2400 {		// PSC3
+			status = "disabled";
+		};
+
+		psc@2600 {		// PSC4
+			status = "disabled";
+		};
+
+		psc@2800 {		// PSC5
+			status = "disabled";
+		};
+
+		psc@2c00 {		// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>; 	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>; 	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				compatible = "intel,lxt971";
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
+		i2c@3d00 {
+			status = "disabled";
 		};
 
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
 			hwmon@2c {
 				compatible = "ad,adm9240";
 				reg = <0x2c>;
@@ -186,20 +123,9 @@
 				reg = <0x51>;
 			};
 		};
-
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
-		};
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <
 				/* IDSEL 0x10 */
@@ -208,20 +134,12 @@
 				0x8000 0 0 3 &mpc5200_pic 0 2 3
 				0x8000 0 0 4 &mpc5200_pic 0 1 3
 				>;
-		clock-frequency = <0>; // From boot loader
-		interrupts = <2 8 0 2 9 0 2 10 0>;
-		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x60000000 0x60000000 0 0x10000000
 			  0x02000000 0 0x90000000 0x90000000 0 0x10000000
 			  0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = <0 0 0xff800000 0x00800000
 			  1 0 0x80000000 0x00800000
 			  3 0 0x80000000 0x00800000>;
diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts
index 28d77758d8be..9e354997eb7e 100644
--- a/arch/powerpc/boot/dts/pcm030.dts
+++ b/arch/powerpc/boot/dts/pcm030.dts
@@ -12,244 +12,92 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "phytec,pcm030";
 	compatible = "phytec,pcm030";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x04000000>;	// 64MB
-	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
-		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
+		timer@600 {		// General Purpose Timer
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
 		gpt2: timer@620 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt3: timer@630 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt4: timer@640 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt5: timer@650 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt6: timer@660 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt7: timer@670 {	// General Purpose Timer in GPIO mode
 			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@900 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 17 0>;
-			reg = <0x900 0x80>;
-		};
-
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
-		};
-
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
-		};
-
 		psc@2000 { /* PSC1 in ac97 mode */
 			compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97";
 			cell-index = <0>;
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
 		/* PSC2 port is used by CAN1/2 */
+		psc@2200 {
+			status = "disabled";
+		};
 
 		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2400 0x100>;
-			interrupts = <2 3 0>;
 		};
 
 		/* PSC4 is ??? */
+		psc@2600 {
+			status = "disabled";
+		};
 
 		/* PSC5 is ??? */
+		psc@2800 {
+			status = "disabled";
+		};
 
 		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
-		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-		};
-
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
 			rtc@51 {
 				compatible = "nxp,pcf8563";
 				reg = <0x51>;
@@ -268,12 +116,6 @@
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
 				 0xc000 0 0 2 &mpc5200_pic 1 1 3
@@ -284,11 +126,12 @@
 				 0xc800 0 0 2 &mpc5200_pic 1 2 3
 				 0xc800 0 0 3 &mpc5200_pic 1 3 3
 				 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
-		clock-frequency = <0>; // From boot loader
-		interrupts = <2 8 0 2 9 0 2 10 0>;
-		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
 			  0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
 			  0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
 	};
+
+	localbus {
+		status = "disabled";
+	};
 };
diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts
index 9dee52b67477..1dd478bfff96 100644
--- a/arch/powerpc/boot/dts/pcm032.dts
+++ b/arch/powerpc/boot/dts/pcm032.dts
@@ -12,99 +12,37 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "phytec,pcm032";
 	compatible = "phytec,pcm032";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
 
 	memory {
-		device_type = "memory";
 		reg = <0x00000000 0x08000000>;	// 128MB
 	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
-		timer@600 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
+		timer@600 {		// General Purpose Timer
 			fsl,has-wdt;
 		};
 
-		timer@610 {	// General Purpose Timer
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
-		};
-
 		gpt2: timer@620 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt3: timer@630 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x630 0x10>;
-			interrupts = <1 12 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt4: timer@640 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt5: timer@650 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
@@ -118,138 +56,49 @@
 		};
 
 		gpt7: timer@670 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
-		rtc@800 {	// Real time clock
-			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
-			reg = <0x800 0x100>;
-			interrupts = <1 5 0 1 6 0>;
-		};
-
-		can@900 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 17 0>;
-			reg = <0x900 0x80>;
-		};
-
-		can@980 {
-			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
-			interrupts = <2 18 0>;
-			reg = <0x980 0x80>;
-		};
-
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		spi@f00 {
-			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
-			reg = <0xf00 0x20>;
-			interrupts = <2 13 0 2 14 0>;
-		};
-
-		usb@1000 {
-			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
-			reg = <0x1000 0xff>;
-			interrupts = <2 6 0>;
-		};
-
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
-		};
-
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
-		};
-
 		psc@2000 {	/* PSC1 is ac97 */
 			compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
 			cell-index = <0>;
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
 		/* PSC2 port is used by CAN1/2 */
+		psc@2200 {
+			status = "disabled";
+		};
 
 		psc@2400 { /* PSC3 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2400 0x100>;
-			interrupts = <2 3 0>;
 		};
 
 		/* PSC4 is ??? */
+		psc@2600 {
+			status = "disabled";
+		};
 
 		/* PSC5 is ??? */
+		psc@2800 {
+			status = "disabled";
+		};
 
 		psc@2c00 { /* PSC6 in UART mode */
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
-		};
-
-		i2c@3d00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d00 0x40>;
-			interrupts = <2 15 0>;
-		};
-
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
 			rtc@51 {
 				compatible = "nxp,pcf8563";
 				reg = <0x51>;
@@ -260,20 +109,9 @@
 				pagesize = <32>;
 			};
 		};
-
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
-		};
 	};
 
 	pci@f0000d00 {
-		#interrupt-cells = <1>;
-		#size-cells = <2>;
-		#address-cells = <3>;
-		device_type = "pci";
-		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
-		reg = <0xf0000d00 0x100>;
 		interrupt-map-mask = <0xf800 0 0 7>;
 		interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
 				 0xc000 0 0 2 &mpc5200_pic 1 1 3
@@ -284,20 +122,12 @@
 				 0xc800 0 0 2 &mpc5200_pic 1 2 3
 				 0xc800 0 0 3 &mpc5200_pic 1 3 3
 				 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
-		clock-frequency = <0>; // From boot loader
-		interrupts = <2 8 0 2 9 0 2 10 0>;
-		bus-range = <0 0>;
 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
 			  0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
 			  0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = <0 0 0xfe000000 0x02000000
 			  1 0 0xfc000000 0x02000000
 			  2 0 0xfbe00000 0x00200000
@@ -350,40 +180,39 @@
 			bank-width = <2>;
 		};
 
-                /*
+		/*
 		 * example snippets for FPGA
 		 *
 		 * fpga@3,0 {
-		 *         compatible = "fpga_driver";
-		 *         reg = <3 0 0x02000000>;
-		 *         bank-width = <4>;
+		 *	 compatible = "fpga_driver";
+		 *	 reg = <3 0 0x02000000>;
+		 *	 bank-width = <4>;
 		 * };
 		 *
 		 * fpga@4,0 {
-		 *         compatible = "fpga_driver";
-		 *         reg = <4 0 0x02000000>;
-		 *         bank-width = <4>;
+		 *	 compatible = "fpga_driver";
+		 *	 reg = <4 0 0x02000000>;
+		 *	 bank-width = <4>;
 		 * };
-                 */
+		 */
 
-                /*
+		/*
 		 * example snippets for free chipselects
-                 *
+		 *
 		 * device@5,0 {
-		 *         compatible = "custom_driver";
-		 *         reg = <5 0 0x02000000>;
+		 *	 compatible = "custom_driver";
+		 *	 reg = <5 0 0x02000000>;
 		 * };
-                 *
+		 *
 		 * device@6,0 {
-		 *         compatible = "custom_driver";
-		 *         reg = <6 0 0x02000000>;
+		 *	 compatible = "custom_driver";
+		 *	 reg = <6 0 0x02000000>;
 		 * };
-                 *
+		 *
 		 * device@7,0 {
-		 *         compatible = "custom_driver";
-		 *         reg = <7 0 0x02000000>;
+		 *	 compatible = "custom_driver";
+		 *	 reg = <7 0 0x02000000>;
 		 * };
-                 */
+		 */
 	};
 };
-
diff --git a/arch/powerpc/boot/dts/uc101.dts b/arch/powerpc/boot/dts/uc101.dts
index e00441a3e5a7..ba83d5488ec6 100644
--- a/arch/powerpc/boot/dts/uc101.dts
+++ b/arch/powerpc/boot/dts/uc101.dts
@@ -11,79 +11,24 @@
  * option) any later version.
  */
 
-/dts-v1/;
+/include/ "mpc5200b.dtsi"
 
 / {
 	model = "manroland,uc101";
 	compatible = "manroland,uc101";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&mpc5200_pic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		PowerPC,5200@0 {
-			device_type = "cpu";
-			reg = <0>;
-			d-cache-line-size = <32>;
-			i-cache-line-size = <32>;
-			d-cache-size = <0x4000>;	// L1, 16K
-			i-cache-size = <0x4000>;	// L1, 16K
-			timebase-frequency = <0>;	// from bootloader
-			bus-frequency = <0>;		// from bootloader
-			clock-frequency = <0>;		// from bootloader
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x04000000>;	// 64MB
-	};
 
 	soc5200@f0000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc5200b-immr";
-		ranges = <0 0xf0000000 0x0000c000>;
-		reg = <0xf0000000 0x00000100>;
-		bus-frequency = <0>;		// from bootloader
-		system-frequency = <0>;		// from bootloader
-
-		cdm@200 {
-			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
-			reg = <0x200 0x38>;
-		};
-
-		mpc5200_pic: interrupt-controller@500 {
-			// 5200 interrupts are encoded into two levels;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
-			reg = <0x500 0x80>;
-		};
-
 		gpt0: timer@600 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x600 0x10>;
-			interrupts = <1 9 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt1: timer@610 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x610 0x10>;
-			interrupts = <1 10 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt2: timer@620 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x620 0x10>;
-			interrupts = <1 11 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
@@ -97,118 +42,85 @@
 		};
 
 		gpt4: timer@640 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x640 0x10>;
-			interrupts = <1 13 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt5: timer@650 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x650 0x10>;
-			interrupts = <1 14 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt6: timer@660 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x660 0x10>;
-			interrupts = <1 15 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
 		gpt7: timer@670 {	// General Purpose Timer in GPIO mode
-			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
-			reg = <0x670 0x10>;
-			interrupts = <1 16 0>;
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
 
-		gpio_simple: gpio@b00 {
-			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
-			reg = <0xb00 0x40>;
-			interrupts = <1 7 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		rtc@800 {
+			status = "disabled";
 		};
 
-		gpio_wkup: gpio@c00 {
-			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
-			reg = <0xc00 0x40>;
-			interrupts = <1 8 0 0 3 0>;
-			gpio-controller;
-			#gpio-cells = <2>;
+		can@900 {
+			status = "disabled";
+		};
+
+		can@980 {
+			status = "disabled";
 		};
 
-		dma-controller@1200 {
-			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
-			reg = <0x1200 0x80>;
-			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
-			              3 4 0  3 5 0  3 6 0  3 7 0
-			              3 8 0  3 9 0  3 10 0  3 11 0
-			              3 12 0  3 13 0  3 14 0  3 15 0>;
+		spi@f00 {
+			status = "disabled";
 		};
 
-		xlb@1f00 {
-			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
-			reg = <0x1f00 0x100>;
+		usb@1000 {
+			status = "disabled";
 		};
 
-		psc@2000 { /* PSC1 in UART mode */
+		psc@2000 {	// PSC1
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2000 0x100>;
-			interrupts = <2 1 0>;
 		};
 
-		psc@2200 { /* PSC2 in UART mode */
+		psc@2200 {	// PSC2
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2200 0x100>;
-			interrupts = <2 2 0>;
 		};
 
-		psc@2c00 {		/* PSC6 in UART mode */
+		psc@2400 {	// PSC3
+			status = "disabled";
+		};
+
+		psc@2600 {	// PSC4
+			status = "disabled";
+		};
+
+		psc@2800 {	// PSC5
+			status = "disabled";
+		};
+
+		psc@2c00 {	// PSC6
 			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
-			reg = <0x2c00 0x100>;
-			interrupts = <2 4 0>;
 		};
 
 		ethernet@3000 {
-			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
-			reg = <0x3000 0x400>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-			interrupts = <2 5 0>;
 			phy-handle = <&phy0>;
 		};
 
 		mdio@3000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
-			reg = <0x3000 0x400>;	// fec range, since we need to setup fec interrupts
-			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
-
 			phy0: ethernet-phy@0 {
 				compatible = "intel,lxt971";
 				reg = <0>;
 			};
 		};
 
-		ata@3a00 {
-			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
-			reg = <0x3a00 0x100>;
-			interrupts = <2 7 0>;
+		i2c@3d00 {
+			status = "disabled";
 		};
 
 		i2c@3d40 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
-			reg = <0x3d40 0x40>;
-			interrupts = <2 16 0>;
 			fsl,preserve-clocking;
 			clock-frequency = <400000>;
 
@@ -221,19 +133,13 @@
 				reg = <0x51>;
 			};
 		};
+	};
 
-		sram@8000 {
-			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
-			reg = <0x8000 0x4000>;
-		};
+	pci@f0000d00 {
+		status = "disabled";
 	};
 
 	localbus {
-		compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-
 		ranges = <0 0 0xff800000 0x00800000
 			  1 0 0x80000000 0x00800000
 			  3 0 0x80000000 0x00800000>;
-- 
cgit v1.2.3-59-g8ed1b


From 301a3da358b4af84915f575479e4f0885be47b73 Mon Sep 17 00:00:00 2001
From: Grant Likely <grant.likely@secretlab.ca>
Date: Mon, 3 Jan 2011 15:02:47 -0700
Subject: powerpc/405: Fix missing #{address,size}-cells in i2c node

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 arch/powerpc/boot/dts/hotfoot.dts | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/hotfoot.dts b/arch/powerpc/boot/dts/hotfoot.dts
index cad9c3840afc..71d3bb4931dc 100644
--- a/arch/powerpc/boot/dts/hotfoot.dts
+++ b/arch/powerpc/boot/dts/hotfoot.dts
@@ -117,6 +117,8 @@
 			};
 
 			IIC: i2c@ef600500 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "ibm,iic-405ep", "ibm,iic";
 				reg = <0xef600500 0x00000011>;
 				interrupt-parent = <&UIC0>;
-- 
cgit v1.2.3-59-g8ed1b


From fd066e850351e21d1b385cde35fadf66761bc053 Mon Sep 17 00:00:00 2001
From: Ilya Yanok <yanok@emcraft.com>
Date: Wed, 27 Oct 2010 02:02:36 +0200
Subject: powerpc/mpc8308: fix USB DR controller initialization

MPC8308 has ULPI pin muxing settings in SICRH register, bits 17-18
which is different from both MPC8313 and MPC8315.
Also MPC8308 doesn't have REFSEL, UTMI_PHY_EN and OTG_PORT fields
in the USB DR controller CONTROL register.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/boot/dts/mpc8308rdb.dts  |  2 +-
 arch/powerpc/platforms/83xx/mpc83xx.h |  2 ++
 arch/powerpc/platforms/83xx/usb.c     | 21 ++++++++++++++++-----
 3 files changed, 19 insertions(+), 6 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/mpc8308rdb.dts b/arch/powerpc/boot/dts/mpc8308rdb.dts
index a97eb2db5a18..1e2b88899443 100644
--- a/arch/powerpc/boot/dts/mpc8308rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8308rdb.dts
@@ -109,7 +109,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
-		compatible = "fsl,mpc8315-immr", "simple-bus";
+		compatible = "fsl,mpc8308-immr", "simple-bus";
 		ranges = <0 0xe0000000 0x00100000>;
 		reg = <0xe0000000 0x00000200>;
 		bus-frequency = <0>;
diff --git a/arch/powerpc/platforms/83xx/mpc83xx.h b/arch/powerpc/platforms/83xx/mpc83xx.h
index 0fea8811d45b..82a434510d83 100644
--- a/arch/powerpc/platforms/83xx/mpc83xx.h
+++ b/arch/powerpc/platforms/83xx/mpc83xx.h
@@ -35,6 +35,8 @@
 
 /* system i/o configuration register high */
 #define MPC83XX_SICRH_OFFS         0x118
+#define MPC8308_SICRH_USB_MASK     0x000c0000
+#define MPC8308_SICRH_USB_ULPI     0x00040000
 #define MPC834X_SICRH_USB_UTMI     0x00020000
 #define MPC831X_SICRH_USB_MASK     0x000000e0
 #define MPC831X_SICRH_USB_ULPI     0x000000a0
diff --git a/arch/powerpc/platforms/83xx/usb.c b/arch/powerpc/platforms/83xx/usb.c
index 3ba4bb7d41bb..2c64164722d0 100644
--- a/arch/powerpc/platforms/83xx/usb.c
+++ b/arch/powerpc/platforms/83xx/usb.c
@@ -127,7 +127,8 @@ int mpc831x_usb_cfg(void)
 
 	/* Configure clock */
 	immr_node = of_get_parent(np);
-	if (immr_node && of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
+	if (immr_node && (of_device_is_compatible(immr_node, "fsl,mpc8315-immr") ||
+			of_device_is_compatible(immr_node, "fsl,mpc8308-immr")))
 		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
 		                MPC8315_SCCR_USB_MASK,
 		                MPC8315_SCCR_USB_DRCM_01);
@@ -138,7 +139,11 @@ int mpc831x_usb_cfg(void)
 
 	/* Configure pin mux for ULPI.  There is no pin mux for UTMI */
 	if (prop && !strcmp(prop, "ulpi")) {
-		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+					MPC8308_SICRH_USB_MASK,
+					MPC8308_SICRH_USB_ULPI);
+		} else if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
 			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
 					MPC8315_SICRL_USB_MASK,
 					MPC8315_SICRL_USB_ULPI);
@@ -173,6 +178,9 @@ int mpc831x_usb_cfg(void)
 		     !strcmp(prop, "utmi"))) {
 		u32 refsel;
 
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr"))
+			goto out;
+
 		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
 			refsel = CONTROL_REFSEL_24MHZ;
 		else
@@ -186,9 +194,11 @@ int mpc831x_usb_cfg(void)
 		temp = CONTROL_PHY_CLK_SEL_ULPI;
 #ifdef CONFIG_USB_OTG
 		/* Set OTG_PORT */
-		dr_mode = of_get_property(np, "dr_mode", NULL);
-		if (dr_mode && !strcmp(dr_mode, "otg"))
-			temp |= CONTROL_OTG_PORT;
+		if (!of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			dr_mode = of_get_property(np, "dr_mode", NULL);
+			if (dr_mode && !strcmp(dr_mode, "otg"))
+				temp |= CONTROL_OTG_PORT;
+		}
 #endif /* CONFIG_USB_OTG */
 		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
 	} else {
@@ -196,6 +206,7 @@ int mpc831x_usb_cfg(void)
 		ret = -EINVAL;
 	}
 
+out:
 	iounmap(usb_regs);
 	of_node_put(np);
 	return ret;
-- 
cgit v1.2.3-59-g8ed1b


From b2e0861e51f2961954330dcafe6d148ee3ab5cff Mon Sep 17 00:00:00 2001
From: Timur Tabi <timur@freescale.com>
Date: Fri, 3 Dec 2010 10:52:14 -0600
Subject: powerpc/85xx: fix compatible properties of the P1022DS DMA nodes used
 for audio

In order to prevent the fsl_dma driver from claiming the DMA channels that the
P1022DS audio driver needs, the compatible properties for those nodes must say
"fsl,ssi-dma-channel" instead of "fsl,eloplus-dma-channel".

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/boot/dts/p1022ds.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/dts/p1022ds.dts b/arch/powerpc/boot/dts/p1022ds.dts
index 2bbecbb4cbf9..69422eb24d97 100644
--- a/arch/powerpc/boot/dts/p1022ds.dts
+++ b/arch/powerpc/boot/dts/p1022ds.dts
@@ -291,13 +291,13 @@
 			ranges = <0x0 0xc100 0x200>;
 			cell-index = <1>;
 			dma00: dma-channel@0 {
-				compatible = "fsl,eloplus-dma-channel";
+				compatible = "fsl,ssi-dma-channel";
 				reg = <0x0 0x80>;
 				cell-index = <0>;
 				interrupts = <76 2>;
 			};
 			dma01: dma-channel@80 {
-				compatible = "fsl,eloplus-dma-channel";
+				compatible = "fsl,ssi-dma-channel";
 				reg = <0x80 0x80>;
 				cell-index = <1>;
 				interrupts = <77 2>;
-- 
cgit v1.2.3-59-g8ed1b


From 4d9ef89dee13e964ea8b064d82ff55cf36209237 Mon Sep 17 00:00:00 2001
From: Ben Hutchings <ben@decadent.org.uk>
Date: Sat, 8 Jan 2011 14:24:01 +0000
Subject: powerpc/boot/dts: Install dts from the right directory

The dts-installed variable is initialised using a wildcard path that
will be expanded relative to the build directory.  Use the existing
variable dtstree to generate an absolute wildcard path that will work
when building in a separate directory.

Reported-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Gerhard Pircher <gerhard_pircher@gmx.net> [against 2.6.32]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/boot/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'arch/powerpc/boot')

diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 96deec63bcf3..89178164af5e 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -368,7 +368,7 @@ INSTALL := install
 extra-installed		:= $(patsubst $(obj)/%, $(DESTDIR)$(WRAPPER_OBJDIR)/%, $(extra-y))
 hostprogs-installed	:= $(patsubst %, $(DESTDIR)$(WRAPPER_BINDIR)/%, $(hostprogs-y))
 wrapper-installed	:= $(DESTDIR)$(WRAPPER_BINDIR)/wrapper
-dts-installed		:= $(patsubst $(obj)/dts/%, $(DESTDIR)$(WRAPPER_DTSDIR)/%, $(wildcard $(obj)/dts/*.dts))
+dts-installed		:= $(patsubst $(dtstree)/%, $(DESTDIR)$(WRAPPER_DTSDIR)/%, $(wildcard $(dtstree)/*.dts))
 
 all-installed		:= $(extra-installed) $(hostprogs-installed) $(wrapper-installed) $(dts-installed)
 
-- 
cgit v1.2.3-59-g8ed1b