From 368ff8f14d6ed8e9fd3b7c2156f2607719bf5a7a Mon Sep 17 00:00:00 2001 From: Suzuki Poulose Date: Wed, 14 Dec 2011 22:58:37 +0000 Subject: powerpc: Define virtual-physical translations for RELOCATABLE We find the runtime address of _stext and relocate ourselves based on the following calculation. virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) + MODULO(_stext.run,KERNEL_TLB_PIN_SIZE) relocate() is called with the Effective Virtual Base Address (as shown below) | Phys. Addr| Virt. Addr | Page |------------------------| Boundary | | | | | | | | | Kernel Load |___________|_ __ _ _ _ _|<- Effective Addr(_stext)| | ^ |Virt. Base Addr | | | | | | | | | |reloc_offset| | | | | | | | | | |______v_____|<-(KERNELBASE)%TLB_SIZE | | | | | | | | | Page |-----------|------------| Boundary | | | On BookE, we need __va() & __pa() early in the boot process to access the device tree. Currently this has been defined as : #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + KERNELBASE) where: PHYSICAL_START is kernstart_addr - a variable updated at runtime. KERNELBASE is the compile time Virtual base address of kernel. This won't work for us, as kernstart_addr is dynamic and will yield different results for __va()/__pa() for same mapping. e.g., Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as PAGE_OFFSET). In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000 = 0xbc100000 , which is wrong. it should be : 0xc0000000 + 0x100000 = 0xc0100000 On platforms which support AMP, like PPC_47x (based on 44x), the kernel could be loaded at highmem. Hence we cannot always depend on the compile time constants for mapping. Here are the possible solutions: 1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of compile time KERNELBASE value, instead of the actual Physical_Address(_stext). The disadvantage is that we may break other users of PHYSICAL_START. They could be replaced with __pa(_stext). 2) Redefine __va() & __pa() with relocation offset #ifdef CONFIG_RELOCATABLE_PPC32 #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET))) #define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET)) #endif where, RELOC_OFFSET could be a) A variable, say relocation_offset (like kernstart_addr), updated at boot time. This impacts performance, as we have to load an additional variable from memory. OR b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \ (KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK)) This introduces more calculations for doing the translation. 3) Redefine __va() & __pa() with a new variable i.e, #define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET)) where VIRT_PHYS_OFFSET : #ifdef CONFIG_RELOCATABLE_PPC32 #define VIRT_PHYS_OFFSET virt_phys_offset #else #define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START) #endif /* CONFIG_RELOCATABLE_PPC32 */ where virt_phy_offset is updated at runtime to : Effective KERNELBASE - kernstart_addr. Taking our example, above: virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr = 0xc0400000 - 0x400000 = 0xc0000000 and __va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000 which is what we want. I have implemented (3) in the following patch which has same cost of operation as the existing one. I have tested the patches on 440x platforms only. However this should work fine for PPC_47x also, as we only depend on the runtime address and the current TLB XLAT entry for the startup code, which is available in r25. I don't have access to a 47x board yet. So, it would be great if somebody could test this on 47x. Signed-off-by: Suzuki K. Poulose Cc: Benjamin Herrenschmidt Cc: Kumar Gala Cc: linuxppc-dev Signed-off-by: Josh Boyer --- arch/powerpc/mm/init_32.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/powerpc/mm/init_32.c') diff --git a/arch/powerpc/mm/init_32.c b/arch/powerpc/mm/init_32.c index 161cefde5c15..60a4e4e84e8c 100644 --- a/arch/powerpc/mm/init_32.c +++ b/arch/powerpc/mm/init_32.c @@ -65,6 +65,13 @@ phys_addr_t memstart_addr = (phys_addr_t)~0ull; EXPORT_SYMBOL(memstart_addr); phys_addr_t kernstart_addr; EXPORT_SYMBOL(kernstart_addr); + +#ifdef CONFIG_RELOCATABLE_PPC32 +/* Used in __va()/__pa() */ +long long virt_phys_offset; +EXPORT_SYMBOL(virt_phys_offset); +#endif + phys_addr_t lowmem_end_addr; int boot_mapsize; -- cgit v1.2.3-59-g8ed1b