From ec21e2ec367697b4803e82662bdff6c8567745fc Mon Sep 17 00:00:00 2001 From: Jeff Kirsher Date: Sat, 11 Jun 2011 02:29:36 -0700 Subject: freescale: Move the Freescale drivers Move the Freescale drivers into drivers/net/ethernet/freescale/ and make the necessary Kconfig and Makefile changes. CC: Sandeep Gopalpet CC: Andy Fleming CC: Shlomi Gridish CC: Li Yang CC: Pantelis Antoniou CC: Vitaly Bordug CC: Dan Malek CC: Sylvain Munaut Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/freescale/Kconfig | 88 ++++++++++++++++++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 drivers/net/ethernet/freescale/Kconfig (limited to 'drivers/net/ethernet/freescale/Kconfig') diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig new file mode 100644 index 000000000000..2fd2c614c08b --- /dev/null +++ b/drivers/net/ethernet/freescale/Kconfig @@ -0,0 +1,88 @@ +# +# Freescale device configuration +# + +config NET_VENDOR_FREESCALE + bool "Freescale devices" + depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ + M523x || M527x || M5272 || M528x || M520x || M532x || \ + IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC || \ + (PPC_MPC52xx && PPC_BESTCOMM) + ---help--- + If you have a network (Ethernet) card belonging to this class, say Y + and read the Ethernet-HOWTO, available from + . + + Note that the answer to this question doesn't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about IBM devices. If you say Y, you will be asked for + your specific card in the following questions. + +if NET_VENDOR_FREESCALE + +config FEC + bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" + depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ + IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC) + default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM + select PHYLIB + ---help--- + Say Y here if you want to use the built-in 10/100 Fast ethernet + controller on some Motorola ColdFire and Freescale i.MX processors. + +config FEC_MPC52xx + tristate "FEC MPC52xx driver" + depends on PPC_MPC52xx && PPC_BESTCOMM + select CRC32 + select PHYLIB + select PPC_BESTCOMM_FEC + ---help--- + This option enables support for the MPC5200's on-chip + Fast Ethernet Controller + If compiled as module, it will be called fec_mpc52xx. + +config FEC_MPC52xx_MDIO + bool "FEC MPC52xx MDIO bus driver" + depends on FEC_MPC52xx + default y + ---help--- + The MPC5200's FEC can connect to the Ethernet either with + an external MII PHY chip or 10 Mbps 7-wire interface + (Motorola? industry standard). + If your board uses an external PHY connected to FEC, enable this. + If not sure, enable. + If compiled as module, it will be called fec_mpc52xx_phy. + +source "drivers/net/ethernet/freescale/fs_enet/Kconfig" + +config FSL_PQ_MDIO + tristate "Freescale PQ MDIO" + depends on FSL_SOC + select PHYLIB + ---help--- + This driver supports the MDIO bus used by the gianfar and UCC drivers. + +config UCC_GETH + tristate "Freescale QE Gigabit Ethernet" + depends on QUICC_ENGINE + select FSL_PQ_MDIO + select PHYLIB + ---help--- + This driver supports the Gigabit Ethernet mode of the QUICC Engine, + which is available on some Freescale SOCs. + +config UGETH_TX_ON_DEMAND + bool "Transmit on Demand support" + depends on UCC_GETH + +config GIANFAR + tristate "Gianfar Ethernet" + depends on FSL_SOC + select FSL_PQ_MDIO + select PHYLIB + select CRC32 + ---help--- + This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, + and MPC86xx family of chips, and the FEC on the 8540. + +endif # NET_VENDOR_FREESCALE -- cgit v1.2.3-59-g8ed1b