From 2a83fba6cae89dd9c0625e68ff8ffff791c67ac0 Mon Sep 17 00:00:00 2001 From: Christian Grönke Date: Tue, 26 Jun 2018 10:12:18 +0000 Subject: igb: Remove superfluous reset to PHY and page 0 selection MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch reverts two previous applied patches to fix an issue that appeared when using SGMII based SFP modules. In the current state the driver will try to reset the PHY before obtaining the phy_addr of the SGMII attached PHY. That leads to an error in e1000_write_phy_reg_sgmii_82575. Causing the initialization to fail: igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k igb: Copyright (c) 2007-2014 Intel Corporation. igb: probe of ????:??:??.? failed with error -3 The patches being reverted are: commit 182785335447957409282ca745aa5bc3968facee Author: Aaron Sierra Date: Tue Nov 29 10:03:56 2016 -0600 igb: reset the PHY before reading the PHY ID commit 440aeca4b9858248d8f16d724d9fa87a4f65fa33 Author: Matwey V Kornilov Date: Thu Nov 24 13:32:48 2016 +0300 igb: Explicitly select page 0 at initialization The first reverted patch directly causes the problem mentioned above. In case of SGMII the phy_addr is not known at this point and will only be obtained by 'igb_get_phy_id_82575' further down in the code. The second removed patch selects forces selection of page 0 in the PHY. Something that the reset tries to address as well. As pointed out by Alexander Duzck, the patch below fixes the same issue but in the proper location: commit 4e684f59d760a2c7c716bb60190783546e2d08a1 Author: Chris J Arges Date: Wed Nov 2 09:13:42 2016 -0500 igb: Workaround for igb i210 firmware issue Reverts: 440aeca4b9858248d8f16d724d9fa87a4f65fa33. Reverts: 182785335447957409282ca745aa5bc3968facee. Signed-off-by: Christian Grönke Reviewed-by: Alexander Duyck Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/e1000_82575.c | 12 ------------ 1 file changed, 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c index b13b42e5a1d9..a795c07d0df7 100644 --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -225,19 +225,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw) hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT; - /* Make sure the PHY is in a good state. Several people have reported - * firmware leaving the PHY's page select register set to something - * other than the default of zero, which causes the PHY ID read to - * access something other than the intended register. - */ - ret_val = hw->phy.ops.reset(hw); - if (ret_val) { - hw_dbg("Error resetting the PHY.\n"); - goto out; - } - /* Set phy->phy_addr and phy->id. */ - igb_write_phy_reg_82580(hw, I347AT4_PAGE_SELECT, 0); ret_val = igb_get_phy_id_82575(hw); if (ret_val) return ret_val; -- cgit v1.2.3-59-g8ed1b