From ef3cf9f2fbef8279a29a027db0d02b56bd0b75f3 Mon Sep 17 00:00:00 2001 From: Christoph Egger Date: Wed, 14 Jul 2010 13:40:36 -0700 Subject: cs89x0: Removing dead SH_HICOSH4 SH_HICOSH4 doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger Signed-off-by: David S. Miller --- drivers/net/cs89x0.c | 51 ++------------------------------------------------- drivers/net/cs89x0.h | 4 ---- 2 files changed, 2 insertions(+), 53 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c index e3a7dca23025..89f2ef7f16de 100644 --- a/drivers/net/cs89x0.c +++ b/drivers/net/cs89x0.c @@ -170,11 +170,7 @@ static char version[] __initdata = /* The cs8900 has 4 IRQ pins, software selectable. cs8900_irq_map maps them to system IRQ numbers. This mapping is card specific and is set to the configuration of the Cirrus Eval board for this chip. */ -#if defined(CONFIG_SH_HICOSH4) -static unsigned int netcard_portlist[] __used __initdata = - { 0x0300, 0}; -static unsigned int cs8900_irq_map[] = {1,0,0,0}; -#elif defined(CONFIG_MACH_IXDP2351) +#if defined(CONFIG_MACH_IXDP2351) static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0}; static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0}; #elif defined(CONFIG_ARCH_IXDP2X01) @@ -578,12 +574,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular) goto out1; } -#ifdef CONFIG_SH_HICOSH4 - /* truly reset the chip */ - writeword(ioaddr, ADD_PORT, 0x0114); - writeword(ioaddr, DATA_PORT, 0x0040); -#endif - /* if they give us an odd I/O address, then do ONE write to the address port, to get it back to address zero, where we expect to find the EISA signature word. An IO with a base of 0x3 @@ -649,37 +639,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular) the driver will always do *something* instead of complain that adapter_cnf is 0. */ -#ifdef CONFIG_SH_HICOSH4 - if (1) { - /* For the HiCO.SH4 board, things are different: we don't - have EEPROM, but there is some data in flash, so we go - get it there directly (MAC). */ - __u16 *confd; - short cnt; - if (((* (volatile __u32 *) 0xa0013ff0) & 0x00ffffff) - == 0x006c3000) { - confd = (__u16*) 0xa0013fc0; - } else { - confd = (__u16*) 0xa001ffc0; - } - cnt = (*confd++ & 0x00ff) >> 1; - while (--cnt > 0) { - __u16 j = *confd++; - - switch (j & 0x0fff) { - case PP_IA: - for (i = 0; i < ETH_ALEN/2; i++) { - dev->dev_addr[i*2] = confd[i] & 0xFF; - dev->dev_addr[i*2+1] = confd[i] >> 8; - } - break; - } - j = (j >> 12) + 1; - confd += j; - cnt -= j; - } - } else -#endif if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) == (EEPROM_OK|EEPROM_PRESENT)) { @@ -734,11 +693,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular) printk("\n"); /* First check to see if an EEPROM is attached. */ -#ifdef CONFIG_SH_HICOSH4 /* no EEPROM on HiCO, don't hazzle with it here */ - if (1) { - printk(KERN_NOTICE "cs89x0: No EEPROM on HiCO.SH4\n"); - } else -#endif + if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0) printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n"); else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) { @@ -1275,7 +1230,6 @@ net_open(struct net_device *dev) int i; int ret; -#if !defined(CONFIG_SH_HICOSH4) && !defined(CONFIG_ARCH_PNX010X) /* uses irq#1, so this won't work */ if (dev->irq < 2) { /* Allow interrupts to be generated by the chip */ /* Cirrus' release had this: */ @@ -1304,7 +1258,6 @@ net_open(struct net_device *dev) } } else -#endif { #ifndef CONFIG_CS89x0_NONISA_IRQ if (((1 << dev->irq) & lp->irq_map) == 0) { diff --git a/drivers/net/cs89x0.h b/drivers/net/cs89x0.h index 204ed37fa9d5..91423b70bb45 100644 --- a/drivers/net/cs89x0.h +++ b/drivers/net/cs89x0.h @@ -437,11 +437,7 @@ #define IRQ_MAP_EEPROM_DATA 0x0046 /* Offset into eeprom for the IRQ map */ #define IRQ_MAP_LEN 0x0004 /* No of bytes to read for the IRQ map */ #define PNP_IRQ_FRMT 0x0022 /* PNP small item IRQ format */ -#ifdef CONFIG_SH_HICOSH4 -#define CS8900_IRQ_MAP 0x0002 /* HiCO-SH4 board has its IRQ on #1 */ -#else #define CS8900_IRQ_MAP 0x1c20 /* This IRQ map is fixed */ -#endif #define CS8920_NO_INTS 0x0F /* Max CS8920 interrupt select # */ -- cgit v1.2.3-59-g8ed1b