From dc07c91b9b4067022210e68d914a6890a4d70622 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Thu, 11 Nov 2010 17:43:57 +0800 Subject: xHCI: fix wMaxPacketSize mask USB2.0 spec 9.6.6 says: For all endpoints, bit 10..0 specify the maximum packet size(in bytes). So the wMaxPacketSize mask should be 0x7ff rather than 0x3ff. This patch should be queued for the stable tree. The bug in xhci_endpoint_init() was present as far back as 2.6.31, and the bug in xhci_get_max_esit_payload() was present when the function was introduced in 2.6.34. Reported-by: Sander Eikelenboom Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci-mem.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host/xhci-mem.c') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 202770676da3..d178761c3981 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1045,7 +1045,7 @@ static inline u32 xhci_get_max_esit_payload(struct xhci_hcd *xhci, if (udev->speed == USB_SPEED_SUPER) return ep->ss_ep_comp.wBytesPerInterval; - max_packet = ep->desc.wMaxPacketSize & 0x3ff; + max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize); max_burst = (ep->desc.wMaxPacketSize & 0x1800) >> 11; /* A 0 in max burst means 1 transfer per ESIT */ return max_packet * (max_burst + 1); @@ -1135,7 +1135,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, /* Fall through */ case USB_SPEED_FULL: case USB_SPEED_LOW: - max_packet = ep->desc.wMaxPacketSize & 0x3ff; + max_packet = GET_MAX_PACKET(ep->desc.wMaxPacketSize); ep_ctx->ep_info2 |= MAX_PACKET(max_packet); break; default: -- cgit v1.2.3-59-g8ed1b From da6699ce4a889c3795624ccdcfe7181cc89f18e8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 26 Oct 2010 16:47:13 -0700 Subject: xhci: Setup array of USB 2.0 and USB 3.0 ports. An xHCI host controller contains USB 2.0 and USB 3.0 ports, which can occur in any order in the PORTSC registers. We cannot read the port speed bits in the PORTSC registers at init time to determine the port speed, since those bits are only valid when a USB device is plugged into the port. Instead, we read the "Supported Protocol Capability" registers in the xHC Extended Capabilities space. Those describe the protocol, port offset in the PORTSC registers, and port count. We use those registers to create two arrays of pointers to the PORTSC registers, one for USB 3.0 ports, and another for USB 2.0 ports. A third array keeps track of the port protocol major revision, and is indexed with the internal xHCI port number. This commit is a bit big, but it should be queued for stable because the "Don't let the USB core disable SuperSpeed ports" patch depends on it. There is no other way to determine which ports are SuperSpeed ports without this patch. Signed-off-by: Sarah Sharp Tested-by: Don Zickus Cc: stable@kernel.org --- drivers/usb/host/xhci-mem.c | 164 ++++++++++++++++++++++++++++++++++++++++++++ drivers/usb/host/xhci.h | 26 +++++++ 2 files changed, 190 insertions(+) (limited to 'drivers/usb/host/xhci-mem.c') diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index d178761c3981..0fae58ef8afe 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1443,6 +1443,13 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->dcbaa = NULL; scratchpad_free(xhci); + + xhci->num_usb2_ports = 0; + xhci->num_usb3_ports = 0; + kfree(xhci->usb2_ports); + kfree(xhci->usb3_ports); + kfree(xhci->port_array); + xhci->page_size = 0; xhci->page_shift = 0; xhci->bus_suspended = 0; @@ -1627,6 +1634,161 @@ static void xhci_set_hc_event_deq(struct xhci_hcd *xhci) &xhci->ir_set->erst_dequeue); } +static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports, + u32 __iomem *addr, u8 major_revision) +{ + u32 temp, port_offset, port_count; + int i; + + if (major_revision > 0x03) { + xhci_warn(xhci, "Ignoring unknown port speed, " + "Ext Cap %p, revision = 0x%x\n", + addr, major_revision); + /* Ignoring port protocol we can't understand. FIXME */ + return; + } + + /* Port offset and count in the third dword, see section 7.2 */ + temp = xhci_readl(xhci, addr + 2); + port_offset = XHCI_EXT_PORT_OFF(temp); + port_count = XHCI_EXT_PORT_COUNT(temp); + xhci_dbg(xhci, "Ext Cap %p, port offset = %u, " + "count = %u, revision = 0x%x\n", + addr, port_offset, port_count, major_revision); + /* Port count includes the current port offset */ + if (port_offset == 0 || (port_offset + port_count - 1) > num_ports) + /* WTF? "Valid values are ‘1’ to MaxPorts" */ + return; + port_offset--; + for (i = port_offset; i < (port_offset + port_count); i++) { + /* Duplicate entry. Ignore the port if the revisions differ. */ + if (xhci->port_array[i] != 0) { + xhci_warn(xhci, "Duplicate port entry, Ext Cap %p," + " port %u\n", addr, i); + xhci_warn(xhci, "Port was marked as USB %u, " + "duplicated as USB %u\n", + xhci->port_array[i], major_revision); + /* Only adjust the roothub port counts if we haven't + * found a similar duplicate. + */ + if (xhci->port_array[i] != major_revision && + xhci->port_array[i] != (u8) -1) { + if (xhci->port_array[i] == 0x03) + xhci->num_usb3_ports--; + else + xhci->num_usb2_ports--; + xhci->port_array[i] = (u8) -1; + } + /* FIXME: Should we disable the port? */ + } + xhci->port_array[i] = major_revision; + if (major_revision == 0x03) + xhci->num_usb3_ports++; + else + xhci->num_usb2_ports++; + } + /* FIXME: Should we disable ports not in the Extended Capabilities? */ +} + +/* + * Scan the Extended Capabilities for the "Supported Protocol Capabilities" that + * specify what speeds each port is supposed to be. We can't count on the port + * speed bits in the PORTSC register being correct until a device is connected, + * but we need to set up the two fake roothubs with the correct number of USB + * 3.0 and USB 2.0 ports at host controller initialization time. + */ +static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags) +{ + u32 __iomem *addr; + u32 offset; + unsigned int num_ports; + int i, port_index; + + addr = &xhci->cap_regs->hcc_params; + offset = XHCI_HCC_EXT_CAPS(xhci_readl(xhci, addr)); + if (offset == 0) { + xhci_err(xhci, "No Extended Capability registers, " + "unable to set up roothub.\n"); + return -ENODEV; + } + + num_ports = HCS_MAX_PORTS(xhci->hcs_params1); + xhci->port_array = kzalloc(sizeof(*xhci->port_array)*num_ports, flags); + if (!xhci->port_array) + return -ENOMEM; + + /* + * For whatever reason, the first capability offset is from the + * capability register base, not from the HCCPARAMS register. + * See section 5.3.6 for offset calculation. + */ + addr = &xhci->cap_regs->hc_capbase + offset; + while (1) { + u32 cap_id; + + cap_id = xhci_readl(xhci, addr); + if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL) + xhci_add_in_port(xhci, num_ports, addr, + (u8) XHCI_EXT_PORT_MAJOR(cap_id)); + offset = XHCI_EXT_CAPS_NEXT(cap_id); + if (!offset || (xhci->num_usb2_ports + xhci->num_usb3_ports) + == num_ports) + break; + /* + * Once you're into the Extended Capabilities, the offset is + * always relative to the register holding the offset. + */ + addr += offset; + } + + if (xhci->num_usb2_ports == 0 && xhci->num_usb3_ports == 0) { + xhci_warn(xhci, "No ports on the roothubs?\n"); + return -ENODEV; + } + xhci_dbg(xhci, "Found %u USB 2.0 ports and %u USB 3.0 ports.\n", + xhci->num_usb2_ports, xhci->num_usb3_ports); + /* + * Note we could have all USB 3.0 ports, or all USB 2.0 ports. + * Not sure how the USB core will handle a hub with no ports... + */ + if (xhci->num_usb2_ports) { + xhci->usb2_ports = kmalloc(sizeof(*xhci->usb2_ports)* + xhci->num_usb2_ports, flags); + if (!xhci->usb2_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) + if (xhci->port_array[i] != 0x03) { + xhci->usb2_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 2.0 port at index %u, " + "addr = %p\n", i, + xhci->usb2_ports[port_index]); + port_index++; + } + } + if (xhci->num_usb3_ports) { + xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)* + xhci->num_usb3_ports, flags); + if (!xhci->usb3_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) + if (xhci->port_array[i] == 0x03) { + xhci->usb3_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 3.0 port at index %u, " + "addr = %p\n", i, + xhci->usb3_ports[port_index]); + port_index++; + } + } + return 0; +} int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) { @@ -1809,6 +1971,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) if (scratchpad_alloc(xhci, flags)) goto fail; + if (xhci_setup_port_arrays(xhci, flags)) + goto fail; return 0; diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 85e65647d445..170c367112d2 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -453,6 +453,24 @@ struct xhci_doorbell_array { #define STREAM_ID_TO_DB(p) (((p) & 0xffff) << 16) +/** + * struct xhci_protocol_caps + * @revision: major revision, minor revision, capability ID, + * and next capability pointer. + * @name_string: Four ASCII characters to say which spec this xHC + * follows, typically "USB ". + * @port_info: Port offset, count, and protocol-defined information. + */ +struct xhci_protocol_caps { + u32 revision; + u32 name_string; + u32 port_info; +}; + +#define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff) +#define XHCI_EXT_PORT_OFF(x) ((x) & 0xff) +#define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff) + /** * struct xhci_container_ctx * @type: Type of context. Used to calculated offsets to contained contexts. @@ -1240,6 +1258,14 @@ struct xhci_hcd { u32 suspended_ports[8]; /* which ports are suspended */ unsigned long resume_done[MAX_HC_PORTS]; + /* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */ + u8 *port_array; + /* Array of pointers to USB 3.0 PORTSC registers */ + u32 __iomem **usb3_ports; + unsigned int num_usb3_ports; + /* Array of pointers to USB 2.0 PORTSC registers */ + u32 __iomem **usb2_ports; + unsigned int num_usb2_ports; }; /* For testing purposes */ -- cgit v1.2.3-59-g8ed1b