From 279385949ebb41ad166fd37505fe552cdb74ed59 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Sun, 19 Jun 2005 01:27:20 +0200 Subject: [PATCH] bring over ieee80211.h from mainline the prototypes and inlines aren't actually needed, but let's not diverge from -mm too far. --- include/net/ieee80211.h | 882 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 882 insertions(+) create mode 100644 include/net/ieee80211.h (limited to 'include/net') diff --git a/include/net/ieee80211.h b/include/net/ieee80211.h new file mode 100644 index 000000000000..7fe57f957a51 --- /dev/null +++ b/include/net/ieee80211.h @@ -0,0 +1,882 @@ +/* + * Merged with mainline ieee80211.h in Aug 2004. Original ieee802_11 + * remains copyright by the original authors + * + * Portions of the merged code are based on Host AP (software wireless + * LAN access point) driver for Intersil Prism2/2.5/3. + * + * Copyright (c) 2001-2002, SSH Communications Security Corp and Jouni Malinen + * + * Copyright (c) 2002-2003, Jouni Malinen + * + * Adaption to a generic IEEE 802.11 stack by James Ketrenos + * + * Copyright (c) 2004, Intel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. See README and COPYING for + * more details. + */ +#ifndef IEEE80211_H +#define IEEE80211_H + +#include /* ETH_ALEN */ +#include /* ARRAY_SIZE */ + +#if WIRELESS_EXT < 17 +#define IW_QUAL_QUAL_INVALID 0x10 +#define IW_QUAL_LEVEL_INVALID 0x20 +#define IW_QUAL_NOISE_INVALID 0x40 +#define IW_QUAL_QUAL_UPDATED 0x1 +#define IW_QUAL_LEVEL_UPDATED 0x2 +#define IW_QUAL_NOISE_UPDATED 0x4 +#endif + +#define IEEE80211_DATA_LEN 2304 +/* Maximum size for the MA-UNITDATA primitive, 802.11 standard section + 6.2.1.1.2. + + The figure in section 7.1.2 suggests a body size of up to 2312 + bytes is allowed, which is a bit confusing, I suspect this + represents the 2304 bytes of real data, plus a possible 8 bytes of + WEP IV and ICV. (this interpretation suggested by Ramiro Barreiro) */ + + +#define IEEE80211_HLEN 30 +#define IEEE80211_FRAME_LEN (IEEE80211_DATA_LEN + IEEE80211_HLEN) + +struct ieee80211_hdr { + u16 frame_ctl; + u16 duration_id; + u8 addr1[ETH_ALEN]; + u8 addr2[ETH_ALEN]; + u8 addr3[ETH_ALEN]; + u16 seq_ctl; + u8 addr4[ETH_ALEN]; +} __attribute__ ((packed)); + +struct ieee80211_hdr_3addr { + u16 frame_ctl; + u16 duration_id; + u8 addr1[ETH_ALEN]; + u8 addr2[ETH_ALEN]; + u8 addr3[ETH_ALEN]; + u16 seq_ctl; +} __attribute__ ((packed)); + +enum eap_type { + EAP_PACKET = 0, + EAPOL_START, + EAPOL_LOGOFF, + EAPOL_KEY, + EAPOL_ENCAP_ASF_ALERT +}; + +static const char *eap_types[] = { + [EAP_PACKET] = "EAP-Packet", + [EAPOL_START] = "EAPOL-Start", + [EAPOL_LOGOFF] = "EAPOL-Logoff", + [EAPOL_KEY] = "EAPOL-Key", + [EAPOL_ENCAP_ASF_ALERT] = "EAPOL-Encap-ASF-Alert" +}; + +static inline const char *eap_get_type(int type) +{ + return (type >= ARRAY_SIZE(eap_types)) ? "Unknown" : eap_types[type]; +} + +struct eapol { + u8 snap[6]; + u16 ethertype; + u8 version; + u8 type; + u16 length; +} __attribute__ ((packed)); + +#define IEEE80211_3ADDR_LEN 24 +#define IEEE80211_4ADDR_LEN 30 +#define IEEE80211_FCS_LEN 4 + +#define MIN_FRAG_THRESHOLD 256U +#define MAX_FRAG_THRESHOLD 2346U + +/* Frame control field constants */ +#define IEEE80211_FCTL_VERS 0x0002 +#define IEEE80211_FCTL_FTYPE 0x000c +#define IEEE80211_FCTL_STYPE 0x00f0 +#define IEEE80211_FCTL_TODS 0x0100 +#define IEEE80211_FCTL_FROMDS 0x0200 +#define IEEE80211_FCTL_MOREFRAGS 0x0400 +#define IEEE80211_FCTL_RETRY 0x0800 +#define IEEE80211_FCTL_PM 0x1000 +#define IEEE80211_FCTL_MOREDATA 0x2000 +#define IEEE80211_FCTL_WEP 0x4000 +#define IEEE80211_FCTL_ORDER 0x8000 + +#define IEEE80211_FTYPE_MGMT 0x0000 +#define IEEE80211_FTYPE_CTL 0x0004 +#define IEEE80211_FTYPE_DATA 0x0008 + +/* management */ +#define IEEE80211_STYPE_ASSOC_REQ 0x0000 +#define IEEE80211_STYPE_ASSOC_RESP 0x0010 +#define IEEE80211_STYPE_REASSOC_REQ 0x0020 +#define IEEE80211_STYPE_REASSOC_RESP 0x0030 +#define IEEE80211_STYPE_PROBE_REQ 0x0040 +#define IEEE80211_STYPE_PROBE_RESP 0x0050 +#define IEEE80211_STYPE_BEACON 0x0080 +#define IEEE80211_STYPE_ATIM 0x0090 +#define IEEE80211_STYPE_DISASSOC 0x00A0 +#define IEEE80211_STYPE_AUTH 0x00B0 +#define IEEE80211_STYPE_DEAUTH 0x00C0 + +/* control */ +#define IEEE80211_STYPE_PSPOLL 0x00A0 +#define IEEE80211_STYPE_RTS 0x00B0 +#define IEEE80211_STYPE_CTS 0x00C0 +#define IEEE80211_STYPE_ACK 0x00D0 +#define IEEE80211_STYPE_CFEND 0x00E0 +#define IEEE80211_STYPE_CFENDACK 0x00F0 + +/* data */ +#define IEEE80211_STYPE_DATA 0x0000 +#define IEEE80211_STYPE_DATA_CFACK 0x0010 +#define IEEE80211_STYPE_DATA_CFPOLL 0x0020 +#define IEEE80211_STYPE_DATA_CFACKPOLL 0x0030 +#define IEEE80211_STYPE_NULLFUNC 0x0040 +#define IEEE80211_STYPE_CFACK 0x0050 +#define IEEE80211_STYPE_CFPOLL 0x0060 +#define IEEE80211_STYPE_CFACKPOLL 0x0070 + +#define IEEE80211_SCTL_FRAG 0x000F +#define IEEE80211_SCTL_SEQ 0xFFF0 + + +/* debug macros */ + +#ifdef CONFIG_IEEE80211_DEBUG +extern u32 ieee80211_debug_level; +#define IEEE80211_DEBUG(level, fmt, args...) \ +do { if (ieee80211_debug_level & (level)) \ + printk(KERN_DEBUG "ieee80211: %c %s " fmt, \ + in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0) +#else +#define IEEE80211_DEBUG(level, fmt, args...) do {} while (0) +#endif /* CONFIG_IEEE80211_DEBUG */ + +/* + * To use the debug system; + * + * If you are defining a new debug classification, simply add it to the #define + * list here in the form of: + * + * #define IEEE80211_DL_xxxx VALUE + * + * shifting value to the left one bit from the previous entry. xxxx should be + * the name of the classification (for example, WEP) + * + * You then need to either add a IEEE80211_xxxx_DEBUG() macro definition for your + * classification, or use IEEE80211_DEBUG(IEEE80211_DL_xxxx, ...) whenever you want + * to send output to that classification. + * + * To add your debug level to the list of levels seen when you perform + * + * % cat /proc/net/ipw/debug_level + * + * you simply need to add your entry to the ipw_debug_levels array. + * + * If you do not see debug_level in /proc/net/ipw then you do not have + * CONFIG_IEEE80211_DEBUG defined in your kernel configuration + * + */ + +#define IEEE80211_DL_INFO (1<<0) +#define IEEE80211_DL_WX (1<<1) +#define IEEE80211_DL_SCAN (1<<2) +#define IEEE80211_DL_STATE (1<<3) +#define IEEE80211_DL_MGMT (1<<4) +#define IEEE80211_DL_FRAG (1<<5) +#define IEEE80211_DL_EAP (1<<6) +#define IEEE80211_DL_DROP (1<<7) + +#define IEEE80211_DL_TX (1<<8) +#define IEEE80211_DL_RX (1<<9) + +#define IEEE80211_ERROR(f, a...) printk(KERN_ERR "ieee80211: " f, ## a) +#define IEEE80211_WARNING(f, a...) printk(KERN_WARNING "ieee80211: " f, ## a) +#define IEEE80211_DEBUG_INFO(f, a...) IEEE80211_DEBUG(IEEE80211_DL_INFO, f, ## a) + +#define IEEE80211_DEBUG_WX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_WX, f, ## a) +#define IEEE80211_DEBUG_SCAN(f, a...) IEEE80211_DEBUG(IEEE80211_DL_SCAN, f, ## a) +#define IEEE80211_DEBUG_STATE(f, a...) IEEE80211_DEBUG(IEEE80211_DL_STATE, f, ## a) +#define IEEE80211_DEBUG_MGMT(f, a...) IEEE80211_DEBUG(IEEE80211_DL_MGMT, f, ## a) +#define IEEE80211_DEBUG_FRAG(f, a...) IEEE80211_DEBUG(IEEE80211_DL_FRAG, f, ## a) +#define IEEE80211_DEBUG_EAP(f, a...) IEEE80211_DEBUG(IEEE80211_DL_EAP, f, ## a) +#define IEEE80211_DEBUG_DROP(f, a...) IEEE80211_DEBUG(IEEE80211_DL_DROP, f, ## a) +#define IEEE80211_DEBUG_TX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_TX, f, ## a) +#define IEEE80211_DEBUG_RX(f, a...) IEEE80211_DEBUG(IEEE80211_DL_RX, f, ## a) +#include +#include +#include /* ARPHRD_ETHER */ + +#ifndef WIRELESS_SPY +#define WIRELESS_SPY // enable iwspy support +#endif +#include // new driver API + +#ifndef ETH_P_PAE +#define ETH_P_PAE 0x888E /* Port Access Entity (IEEE 802.1X) */ +#endif /* ETH_P_PAE */ + +#define ETH_P_PREAUTH 0x88C7 /* IEEE 802.11i pre-authentication */ + +#ifndef ETH_P_80211_RAW +#define ETH_P_80211_RAW (ETH_P_ECONET + 1) +#endif + +/* IEEE 802.11 defines */ + +#define P80211_OUI_LEN 3 + +struct ieee80211_snap_hdr { + + u8 dsap; /* always 0xAA */ + u8 ssap; /* always 0xAA */ + u8 ctrl; /* always 0x03 */ + u8 oui[P80211_OUI_LEN]; /* organizational universal id */ + +} __attribute__ ((packed)); + +#define SNAP_SIZE sizeof(struct ieee80211_snap_hdr) + +#define WLAN_FC_GET_TYPE(fc) ((fc) & IEEE80211_FCTL_FTYPE) +#define WLAN_FC_GET_STYPE(fc) ((fc) & IEEE80211_FCTL_STYPE) + +#define WLAN_GET_SEQ_FRAG(seq) ((seq) & IEEE80211_SCTL_FRAG) +#define WLAN_GET_SEQ_SEQ(seq) ((seq) & IEEE80211_SCTL_SEQ) + +/* Authentication algorithms */ +#define WLAN_AUTH_OPEN 0 +#define WLAN_AUTH_SHARED_KEY 1 + +#define WLAN_AUTH_CHALLENGE_LEN 128 + +#define WLAN_CAPABILITY_BSS (1<<0) +#define WLAN_CAPABILITY_IBSS (1<<1) +#define WLAN_CAPABILITY_CF_POLLABLE (1<<2) +#define WLAN_CAPABILITY_CF_POLL_REQUEST (1<<3) +#define WLAN_CAPABILITY_PRIVACY (1<<4) +#define WLAN_CAPABILITY_SHORT_PREAMBLE (1<<5) +#define WLAN_CAPABILITY_PBCC (1<<6) +#define WLAN_CAPABILITY_CHANNEL_AGILITY (1<<7) + +/* Status codes */ +#define WLAN_STATUS_SUCCESS 0 +#define WLAN_STATUS_UNSPECIFIED_FAILURE 1 +#define WLAN_STATUS_CAPS_UNSUPPORTED 10 +#define WLAN_STATUS_REASSOC_NO_ASSOC 11 +#define WLAN_STATUS_ASSOC_DENIED_UNSPEC 12 +#define WLAN_STATUS_NOT_SUPPORTED_AUTH_ALG 13 +#define WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION 14 +#define WLAN_STATUS_CHALLENGE_FAIL 15 +#define WLAN_STATUS_AUTH_TIMEOUT 16 +#define WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA 17 +#define WLAN_STATUS_ASSOC_DENIED_RATES 18 +/* 802.11b */ +#define WLAN_STATUS_ASSOC_DENIED_NOSHORT 19 +#define WLAN_STATUS_ASSOC_DENIED_NOPBCC 20 +#define WLAN_STATUS_ASSOC_DENIED_NOAGILITY 21 + +/* Reason codes */ +#define WLAN_REASON_UNSPECIFIED 1 +#define WLAN_REASON_PREV_AUTH_NOT_VALID 2 +#define WLAN_REASON_DEAUTH_LEAVING 3 +#define WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY 4 +#define WLAN_REASON_DISASSOC_AP_BUSY 5 +#define WLAN_REASON_CLASS2_FRAME_FROM_NONAUTH_STA 6 +#define WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA 7 +#define WLAN_REASON_DISASSOC_STA_HAS_LEFT 8 +#define WLAN_REASON_STA_REQ_ASSOC_WITHOUT_AUTH 9 + + +/* Information Element IDs */ +#define WLAN_EID_SSID 0 +#define WLAN_EID_SUPP_RATES 1 +#define WLAN_EID_FH_PARAMS 2 +#define WLAN_EID_DS_PARAMS 3 +#define WLAN_EID_CF_PARAMS 4 +#define WLAN_EID_TIM 5 +#define WLAN_EID_IBSS_PARAMS 6 +#define WLAN_EID_CHALLENGE 16 +#define WLAN_EID_RSN 48 +#define WLAN_EID_GENERIC 221 + +#define IEEE80211_MGMT_HDR_LEN 24 +#define IEEE80211_DATA_HDR3_LEN 24 +#define IEEE80211_DATA_HDR4_LEN 30 + + +#define IEEE80211_STATMASK_SIGNAL (1<<0) +#define IEEE80211_STATMASK_RSSI (1<<1) +#define IEEE80211_STATMASK_NOISE (1<<2) +#define IEEE80211_STATMASK_RATE (1<<3) +#define IEEE80211_STATMASK_WEMASK 0x7 + + +#define IEEE80211_CCK_MODULATION (1<<0) +#define IEEE80211_OFDM_MODULATION (1<<1) + +#define IEEE80211_24GHZ_BAND (1<<0) +#define IEEE80211_52GHZ_BAND (1<<1) + +#define IEEE80211_CCK_RATE_1MB 0x02 +#define IEEE80211_CCK_RATE_2MB 0x04 +#define IEEE80211_CCK_RATE_5MB 0x0B +#define IEEE80211_CCK_RATE_11MB 0x16 +#define IEEE80211_OFDM_RATE_6MB 0x0C +#define IEEE80211_OFDM_RATE_9MB 0x12 +#define IEEE80211_OFDM_RATE_12MB 0x18 +#define IEEE80211_OFDM_RATE_18MB 0x24 +#define IEEE80211_OFDM_RATE_24MB 0x30 +#define IEEE80211_OFDM_RATE_36MB 0x48 +#define IEEE80211_OFDM_RATE_48MB 0x60 +#define IEEE80211_OFDM_RATE_54MB 0x6C +#define IEEE80211_BASIC_RATE_MASK 0x80 + +#define IEEE80211_CCK_RATE_1MB_MASK (1<<0) +#define IEEE80211_CCK_RATE_2MB_MASK (1<<1) +#define IEEE80211_CCK_RATE_5MB_MASK (1<<2) +#define IEEE80211_CCK_RATE_11MB_MASK (1<<3) +#define IEEE80211_OFDM_RATE_6MB_MASK (1<<4) +#define IEEE80211_OFDM_RATE_9MB_MASK (1<<5) +#define IEEE80211_OFDM_RATE_12MB_MASK (1<<6) +#define IEEE80211_OFDM_RATE_18MB_MASK (1<<7) +#define IEEE80211_OFDM_RATE_24MB_MASK (1<<8) +#define IEEE80211_OFDM_RATE_36MB_MASK (1<<9) +#define IEEE80211_OFDM_RATE_48MB_MASK (1<<10) +#define IEEE80211_OFDM_RATE_54MB_MASK (1<<11) + +#define IEEE80211_CCK_RATES_MASK 0x0000000F +#define IEEE80211_CCK_BASIC_RATES_MASK (IEEE80211_CCK_RATE_1MB_MASK | \ + IEEE80211_CCK_RATE_2MB_MASK) +#define IEEE80211_CCK_DEFAULT_RATES_MASK (IEEE80211_CCK_BASIC_RATES_MASK | \ + IEEE80211_CCK_RATE_5MB_MASK | \ + IEEE80211_CCK_RATE_11MB_MASK) + +#define IEEE80211_OFDM_RATES_MASK 0x00000FF0 +#define IEEE80211_OFDM_BASIC_RATES_MASK (IEEE80211_OFDM_RATE_6MB_MASK | \ + IEEE80211_OFDM_RATE_12MB_MASK | \ + IEEE80211_OFDM_RATE_24MB_MASK) +#define IEEE80211_OFDM_DEFAULT_RATES_MASK (IEEE80211_OFDM_BASIC_RATES_MASK | \ + IEEE80211_OFDM_RATE_9MB_MASK | \ + IEEE80211_OFDM_RATE_18MB_MASK | \ + IEEE80211_OFDM_RATE_36MB_MASK | \ + IEEE80211_OFDM_RATE_48MB_MASK | \ + IEEE80211_OFDM_RATE_54MB_MASK) +#define IEEE80211_DEFAULT_RATES_MASK (IEEE80211_OFDM_DEFAULT_RATES_MASK | \ + IEEE80211_CCK_DEFAULT_RATES_MASK) + +#define IEEE80211_NUM_OFDM_RATES 8 +#define IEEE80211_NUM_CCK_RATES 4 +#define IEEE80211_OFDM_SHIFT_MASK_A 4 + + + + +/* NOTE: This data is for statistical purposes; not all hardware provides this + * information for frames received. Not setting these will not cause + * any adverse affects. */ +struct ieee80211_rx_stats { + u32 mac_time; + s8 rssi; + u8 signal; + u8 noise; + u16 rate; /* in 100 kbps */ + u8 received_channel; + u8 control; + u8 mask; + u8 freq; + u16 len; +}; + +/* IEEE 802.11 requires that STA supports concurrent reception of at least + * three fragmented frames. This define can be increased to support more + * concurrent frames, but it should be noted that each entry can consume about + * 2 kB of RAM and increasing cache size will slow down frame reassembly. */ +#define IEEE80211_FRAG_CACHE_LEN 4 + +struct ieee80211_frag_entry { + unsigned long first_frag_time; + unsigned int seq; + unsigned int last_frag; + struct sk_buff *skb; + u8 src_addr[ETH_ALEN]; + u8 dst_addr[ETH_ALEN]; +}; + +struct ieee80211_stats { + unsigned int tx_unicast_frames; + unsigned int tx_multicast_frames; + unsigned int tx_fragments; + unsigned int tx_unicast_octets; + unsigned int tx_multicast_octets; + unsigned int tx_deferred_transmissions; + unsigned int tx_single_retry_frames; + unsigned int tx_multiple_retry_frames; + unsigned int tx_retry_limit_exceeded; + unsigned int tx_discards; + unsigned int rx_unicast_frames; + unsigned int rx_multicast_frames; + unsigned int rx_fragments; + unsigned int rx_unicast_octets; + unsigned int rx_multicast_octets; + unsigned int rx_fcs_errors; + unsigned int rx_discards_no_buffer; + unsigned int tx_discards_wrong_sa; + unsigned int rx_discards_undecryptable; + unsigned int rx_message_in_msg_fragments; + unsigned int rx_message_in_bad_msg_fragments; +}; + +struct ieee80211_device; + +#define SEC_KEY_1 (1<<0) +#define SEC_KEY_2 (1<<1) +#define SEC_KEY_3 (1<<2) +#define SEC_KEY_4 (1<<3) +#define SEC_ACTIVE_KEY (1<<4) +#define SEC_AUTH_MODE (1<<5) +#define SEC_UNICAST_GROUP (1<<6) +#define SEC_LEVEL (1<<7) +#define SEC_ENABLED (1<<8) + +#define SEC_LEVEL_0 0 /* None */ +#define SEC_LEVEL_1 1 /* WEP 40 and 104 bit */ +#define SEC_LEVEL_2 2 /* Level 1 + TKIP */ +#define SEC_LEVEL_2_CKIP 3 /* Level 1 + CKIP */ +#define SEC_LEVEL_3 4 /* Level 2 + CCMP */ + +#define WEP_KEYS 4 +#define WEP_KEY_LEN 13 + +struct ieee80211_security { + u16 active_key:2, + enabled:1, + auth_mode:2, + auth_algo:4, + unicast_uses_group:1; + u8 key_sizes[WEP_KEYS]; + u8 keys[WEP_KEYS][WEP_KEY_LEN]; + u8 level; + u16 flags; +} __attribute__ ((packed)); + + +/* + + 802.11 data frame from AP + + ,-------------------------------------------------------------------. +Bytes | 2 | 2 | 6 | 6 | 6 | 2 | 0..2312 | 4 | + |------|------|---------|---------|---------|------|---------|------| +Desc. | ctrl | dura | DA/RA | TA | SA | Sequ | frame | fcs | + | | tion | (BSSID) | | | ence | data | | + `-------------------------------------------------------------------' + +Total: 28-2340 bytes + +*/ + +struct ieee80211_header_data { + u16 frame_ctl; + u16 duration_id; + u8 addr1[6]; + u8 addr2[6]; + u8 addr3[6]; + u16 seq_ctrl; +}; + +#define BEACON_PROBE_SSID_ID_POSITION 12 + +/* Management Frame Information Element Types */ +#define MFIE_TYPE_SSID 0 +#define MFIE_TYPE_RATES 1 +#define MFIE_TYPE_FH_SET 2 +#define MFIE_TYPE_DS_SET 3 +#define MFIE_TYPE_CF_SET 4 +#define MFIE_TYPE_TIM 5 +#define MFIE_TYPE_IBSS_SET 6 +#define MFIE_TYPE_CHALLENGE 16 +#define MFIE_TYPE_RSN 48 +#define MFIE_TYPE_RATES_EX 50 +#define MFIE_TYPE_GENERIC 221 + +struct ieee80211_info_element_hdr { + u8 id; + u8 len; +} __attribute__ ((packed)); + +struct ieee80211_info_element { + u8 id; + u8 len; + u8 data[0]; +} __attribute__ ((packed)); + +/* + * These are the data types that can make up management packets + * + u16 auth_algorithm; + u16 auth_sequence; + u16 beacon_interval; + u16 capability; + u8 current_ap[ETH_ALEN]; + u16 listen_interval; + struct { + u16 association_id:14, reserved:2; + } __attribute__ ((packed)); + u32 time_stamp[2]; + u16 reason; + u16 status; +*/ + +struct ieee80211_authentication { + struct ieee80211_header_data header; + u16 algorithm; + u16 transaction; + u16 status; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + + +struct ieee80211_probe_response { + struct ieee80211_header_data header; + u32 time_stamp[2]; + u16 beacon_interval; + u16 capability; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + +struct ieee80211_assoc_request_frame { + u16 capability; + u16 listen_interval; + u8 current_ap[ETH_ALEN]; + struct ieee80211_info_element info_element; +} __attribute__ ((packed)); + +struct ieee80211_assoc_response_frame { + struct ieee80211_hdr_3addr header; + u16 capability; + u16 status; + u16 aid; + struct ieee80211_info_element info_element; /* supported rates */ +} __attribute__ ((packed)); + + +struct ieee80211_txb { + u8 nr_frags; + u8 encrypted; + u16 reserved; + u16 frag_size; + u16 payload_size; + struct sk_buff *fragments[0]; +}; + + +/* SWEEP TABLE ENTRIES NUMBER*/ +#define MAX_SWEEP_TAB_ENTRIES 42 +#define MAX_SWEEP_TAB_ENTRIES_PER_PACKET 7 +/* MAX_RATES_LENGTH needs to be 12. The spec says 8, and many APs + * only use 8, and then use extended rates for the remaining supported + * rates. Other APs, however, stick all of their supported rates on the + * main rates information element... */ +#define MAX_RATES_LENGTH ((u8)12) +#define MAX_RATES_EX_LENGTH ((u8)16) +#define MAX_NETWORK_COUNT 128 + +#define CRC_LENGTH 4U + +#define MAX_WPA_IE_LEN 64 + +#define NETWORK_EMPTY_ESSID (1<<0) +#define NETWORK_HAS_OFDM (1<<1) +#define NETWORK_HAS_CCK (1<<2) + +struct ieee80211_network { + /* These entries are used to identify a unique network */ + u8 bssid[ETH_ALEN]; + u8 channel; + /* Ensure null-terminated for any debug msgs */ + u8 ssid[IW_ESSID_MAX_SIZE + 1]; + u8 ssid_len; + + /* These are network statistics */ + struct ieee80211_rx_stats stats; + u16 capability; + u8 rates[MAX_RATES_LENGTH]; + u8 rates_len; + u8 rates_ex[MAX_RATES_EX_LENGTH]; + u8 rates_ex_len; + unsigned long last_scanned; + u8 mode; + u8 flags; + u32 last_associate; + u32 time_stamp[2]; + u16 beacon_interval; + u16 listen_interval; + u16 atim_window; + u8 wpa_ie[MAX_WPA_IE_LEN]; + size_t wpa_ie_len; + u8 rsn_ie[MAX_WPA_IE_LEN]; + size_t rsn_ie_len; + struct list_head list; +}; + +enum ieee80211_state { + IEEE80211_UNINITIALIZED = 0, + IEEE80211_INITIALIZED, + IEEE80211_ASSOCIATING, + IEEE80211_ASSOCIATED, + IEEE80211_AUTHENTICATING, + IEEE80211_AUTHENTICATED, + IEEE80211_SHUTDOWN +}; + +#define DEFAULT_MAX_SCAN_AGE (15 * HZ) +#define DEFAULT_FTS 2346 +#define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x" +#define MAC_ARG(x) ((u8*)(x))[0],((u8*)(x))[1],((u8*)(x))[2],((u8*)(x))[3],((u8*)(x))[4],((u8*)(x))[5] + + +extern inline int is_broadcast_ether_addr(const u8 *addr) +{ + return ((addr[0] == 0xff) && (addr[1] == 0xff) && (addr[2] == 0xff) && \ + (addr[3] == 0xff) && (addr[4] == 0xff) && (addr[5] == 0xff)); +} + +#define CFG_IEEE80211_RESERVE_FCS (1<<0) +#define CFG_IEEE80211_COMPUTE_FCS (1<<1) + +struct ieee80211_device { + struct net_device *dev; + + /* Bookkeeping structures */ + struct net_device_stats stats; + struct ieee80211_stats ieee_stats; + + /* Probe / Beacon management */ + struct list_head network_free_list; + struct list_head network_list; + struct ieee80211_network *networks; + int scans; + int scan_age; + + int iw_mode; /* operating mode (IW_MODE_*) */ + + spinlock_t lock; + + int tx_headroom; /* Set to size of any additional room needed at front + * of allocated Tx SKBs */ + u32 config; + + /* WEP and other encryption related settings at the device level */ + int open_wep; /* Set to 1 to allow unencrypted frames */ + + int reset_on_keychange; /* Set to 1 if the HW needs to be reset on + * WEP key changes */ + + /* If the host performs {en,de}cryption, then set to 1 */ + int host_encrypt; + int host_decrypt; + int ieee802_1x; /* is IEEE 802.1X used */ + + /* WPA data */ + int wpa_enabled; + int drop_unencrypted; + int tkip_countermeasures; + int privacy_invoked; + size_t wpa_ie_len; + u8 *wpa_ie; + + struct list_head crypt_deinit_list; + struct ieee80211_crypt_data *crypt[WEP_KEYS]; + int tx_keyidx; /* default TX key index (crypt[tx_keyidx]) */ + struct timer_list crypt_deinit_timer; + + int bcrx_sta_key; /* use individual keys to override default keys even + * with RX of broad/multicast frames */ + + /* Fragmentation structures */ + struct ieee80211_frag_entry frag_cache[IEEE80211_FRAG_CACHE_LEN]; + unsigned int frag_next_idx; + u16 fts; /* Fragmentation Threshold */ + + /* Association info */ + u8 bssid[ETH_ALEN]; + + enum ieee80211_state state; + + int mode; /* A, B, G */ + int modulation; /* CCK, OFDM */ + int freq_band; /* 2.4Ghz, 5.2Ghz, Mixed */ + int abg_ture; /* ABG flag */ + + /* Callback functions */ + void (*set_security)(struct net_device *dev, + struct ieee80211_security *sec); + int (*hard_start_xmit)(struct ieee80211_txb *txb, + struct net_device *dev); + int (*reset_port)(struct net_device *dev); + + /* This must be the last item so that it points to the data + * allocated beyond this structure by alloc_ieee80211 */ + u8 priv[0]; +}; + +#define IEEE_A (1<<0) +#define IEEE_B (1<<1) +#define IEEE_G (1<<2) +#define IEEE_MODE_MASK (IEEE_A|IEEE_B|IEEE_G) + +extern inline void *ieee80211_priv(struct net_device *dev) +{ + return ((struct ieee80211_device *)netdev_priv(dev))->priv; +} + +extern inline int ieee80211_is_empty_essid(const char *essid, int essid_len) +{ + /* Single white space is for Linksys APs */ + if (essid_len == 1 && essid[0] == ' ') + return 1; + + /* Otherwise, if the entire essid is 0, we assume it is hidden */ + while (essid_len) { + essid_len--; + if (essid[essid_len] != '\0') + return 0; + } + + return 1; +} + +extern inline int ieee80211_is_valid_mode(struct ieee80211_device *ieee, int mode) +{ + /* + * It is possible for both access points and our device to support + * combinations of modes, so as long as there is one valid combination + * of ap/device supported modes, then return success + * + */ + if ((mode & IEEE_A) && + (ieee->modulation & IEEE80211_OFDM_MODULATION) && + (ieee->freq_band & IEEE80211_52GHZ_BAND)) + return 1; + + if ((mode & IEEE_G) && + (ieee->modulation & IEEE80211_OFDM_MODULATION) && + (ieee->freq_band & IEEE80211_24GHZ_BAND)) + return 1; + + if ((mode & IEEE_B) && + (ieee->modulation & IEEE80211_CCK_MODULATION) && + (ieee->freq_band & IEEE80211_24GHZ_BAND)) + return 1; + + return 0; +} + +extern inline int ieee80211_get_hdrlen(u16 fc) +{ + int hdrlen = 24; + + switch (WLAN_FC_GET_TYPE(fc)) { + case IEEE80211_FTYPE_DATA: + if ((fc & IEEE80211_FCTL_FROMDS) && (fc & IEEE80211_FCTL_TODS)) + hdrlen = 30; /* Addr4 */ + break; + case IEEE80211_FTYPE_CTL: + switch (WLAN_FC_GET_STYPE(fc)) { + case IEEE80211_STYPE_CTS: + case IEEE80211_STYPE_ACK: + hdrlen = 10; + break; + default: + hdrlen = 16; + break; + } + break; + } + + return hdrlen; +} + + + +/* ieee80211.c */ +extern void free_ieee80211(struct net_device *dev); +extern struct net_device *alloc_ieee80211(int sizeof_priv); + +extern int ieee80211_set_encryption(struct ieee80211_device *ieee); + +/* ieee80211_tx.c */ + + +extern int ieee80211_xmit(struct sk_buff *skb, + struct net_device *dev); +extern void ieee80211_txb_free(struct ieee80211_txb *); + + +/* ieee80211_rx.c */ +extern int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb, + struct ieee80211_rx_stats *rx_stats); +extern void ieee80211_rx_mgt(struct ieee80211_device *ieee, + struct ieee80211_hdr *header, + struct ieee80211_rx_stats *stats); + +/* iee80211_wx.c */ +extern int ieee80211_wx_get_scan(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); +extern int ieee80211_wx_set_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); +extern int ieee80211_wx_get_encode(struct ieee80211_device *ieee, + struct iw_request_info *info, + union iwreq_data *wrqu, char *key); + + +extern inline void ieee80211_increment_scans(struct ieee80211_device *ieee) +{ + ieee->scans++; +} + +extern inline int ieee80211_get_scans(struct ieee80211_device *ieee) +{ + return ieee->scans; +} + +static inline const char *escape_essid(const char *essid, u8 essid_len) { + static char escaped[IW_ESSID_MAX_SIZE * 2 + 1]; + const char *s = essid; + char *d = escaped; + + if (ieee80211_is_empty_essid(essid, essid_len)) { + memcpy(escaped, "", sizeof("")); + return escaped; + } + + essid_len = min(essid_len, (u8)IW_ESSID_MAX_SIZE); + while (essid_len--) { + if (*s == '\0') { + *d++ = '\\'; + *d++ = '0'; + s++; + } else { + *d++ = *s++; + } + } + *d = '\0'; + return escaped; +} + +#endif /* IEEE80211_H */ -- cgit v1.2.3-59-g8ed1b