From e23ee9d2c4ccb08fdfee3aea0a04a27bccd77433 Mon Sep 17 00:00:00 2001 From: Ilpo Järvinen Date: Fri, 24 Jun 2022 23:54:21 +0300 Subject: serial: Use bits for UART_LSR_BRK_ERROR_BITS/MSR_ANY_DELTA MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Instead of listing the bits for UART_LSR_BRK_ERROR_BITS and UART_MSR_ANY_DELTA in comment, use them to define instead. Reviewed-by: Jiri Slaby Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20220624205424.12686-4-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman --- include/uapi/linux/serial_reg.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h index f51bc8f36813..bab3b39266cc 100644 --- a/include/uapi/linux/serial_reg.h +++ b/include/uapi/linux/serial_reg.h @@ -139,7 +139,7 @@ #define UART_LSR_PE 0x04 /* Parity error indicator */ #define UART_LSR_OE 0x02 /* Overrun error indicator */ #define UART_LSR_DR 0x01 /* Receiver data ready */ -#define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */ +#define UART_LSR_BRK_ERROR_BITS (UART_LSR_BI|UART_LSR_FE|UART_LSR_PE|UART_LSR_OE) #define UART_MSR 6 /* In: Modem Status Register */ #define UART_MSR_DCD 0x80 /* Data Carrier Detect */ @@ -150,7 +150,7 @@ #define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ #define UART_MSR_DDSR 0x02 /* Delta DSR */ #define UART_MSR_DCTS 0x01 /* Delta CTS */ -#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ +#define UART_MSR_ANY_DELTA (UART_MSR_DDCD|UART_MSR_TERI|UART_MSR_DDSR|UART_MSR_DCTS) #define UART_SCR 7 /* I/O: Scratch Register */ -- cgit v1.2.3-59-g8ed1b From 4f768e94774c58c9f7f54ebd38dadf172970046a Mon Sep 17 00:00:00 2001 From: Ilpo Järvinen Date: Fri, 24 Jun 2022 23:42:09 +0300 Subject: serial: Support for RS-485 multipoint addresses MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add support for RS-485 multipoint addressing using 9th bit [*]. The addressing mode is configured through ->rs485_config(). ADDRB in termios indicates 9th bit addressing mode is enabled. In this mode, 9th bit is used to indicate an address (byte) within the communication line. ADDRB can only be enabled/disabled through ->rs485_config() that is also responsible for setting the destination and receiver (filter) addresses. Add traps to detect unwanted changes to struct serial_rs485 layout using static_assert(). [*] Technically, RS485 is just an electronic spec and does not itself specify the 9th bit addressing mode but 9th bit seems at least "semi-standard" way to do addressing with RS485. Signed-off-by: Ilpo Järvinen Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman --- Documentation/driver-api/serial/driver.rst | 2 ++ Documentation/driver-api/serial/serial-rs485.rst | 26 +++++++++++++++++++++++- drivers/tty/serial/serial_core.c | 22 +++++++++++++++++++- drivers/tty/tty_ioctl.c | 4 ++++ include/uapi/asm-generic/termbits-common.h | 1 + include/uapi/linux/serial.h | 20 ++++++++++++++++-- 6 files changed, 71 insertions(+), 4 deletions(-) (limited to 'include/uapi/linux') diff --git a/Documentation/driver-api/serial/driver.rst b/Documentation/driver-api/serial/driver.rst index 1e7ab4142d49..ee1679858aa2 100644 --- a/Documentation/driver-api/serial/driver.rst +++ b/Documentation/driver-api/serial/driver.rst @@ -261,6 +261,8 @@ hardware. - parity enable PARODD - odd parity (when PARENB is in force) + ADDRB + - address bit (changed through .rs485_config()). CREAD - enable reception of characters (if not set, still receive characters from the port, but diff --git a/Documentation/driver-api/serial/serial-rs485.rst b/Documentation/driver-api/serial/serial-rs485.rst index 00b5d333acba..6ebad75c74ed 100644 --- a/Documentation/driver-api/serial/serial-rs485.rst +++ b/Documentation/driver-api/serial/serial-rs485.rst @@ -99,7 +99,31 @@ RS485 Serial Communications /* Error handling. See errno. */ } -5. References +5. Multipoint Addressing +======================== + + The Linux kernel provides addressing mode for multipoint RS-485 serial + communications line. The addressing mode is enabled with SER_RS485_ADDRB + flag in serial_rs485. Struct serial_rs485 has two additional flags and + fields for enabling receive and destination addresses. + + Address mode flags: + - SER_RS485_ADDRB: Enabled addressing mode (sets also ADDRB in termios). + - SER_RS485_ADDR_RECV: Receive (filter) address enabled. + - SER_RS485_ADDR_DEST: Set destination address. + + Address fields (enabled with corresponding SER_RS485_ADDR_* flag): + - addr_recv: Receive address. + - addr_dest: Destination address. + + Once a receive address is set, the communication can occur only with the + particular device and other peers are filtered out. It is left up to the + receiver side to enforce the filtering. Receive address will be cleared + if SER_RS485_ADDR_RECV is not set. + + Note: not all devices supporting RS485 support multipoint addressing. + +6. References ============= [1] include/uapi/linux/serial.h diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index 2529153c8979..85ef7ef00b82 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -1288,6 +1288,17 @@ static int uart_check_rs485_flags(struct uart_port *port, struct serial_rs485 *r if (flags & ~port->rs485_supported->flags) return -EINVAL; + /* Asking for address w/o addressing mode? */ + if (!(rs485->flags & SER_RS485_ADDRB) && + (rs485->flags & (SER_RS485_ADDR_RECV|SER_RS485_ADDR_DEST))) + return -EINVAL; + + /* Address given but not enabled? */ + if (!(rs485->flags & SER_RS485_ADDR_RECV) && rs485->addr_recv) + return -EINVAL; + if (!(rs485->flags & SER_RS485_ADDR_DEST) && rs485->addr_dest) + return -EINVAL; + return 0; } @@ -1343,7 +1354,8 @@ static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs4 rs485->flags &= supported_flags; /* Return clean padding area to userspace */ - memset(rs485->padding, 0, sizeof(rs485->padding)); + memset(rs485->padding0, 0, sizeof(rs485->padding0)); + memset(rs485->padding1, 0, sizeof(rs485->padding1)); } int uart_rs485_config(struct uart_port *port) @@ -3402,5 +3414,13 @@ int uart_get_rs485_mode(struct uart_port *port) } EXPORT_SYMBOL_GPL(uart_get_rs485_mode); +/* Compile-time assertions for serial_rs485 layout */ +static_assert(offsetof(struct serial_rs485, padding) == + (offsetof(struct serial_rs485, delay_rts_after_send) + sizeof(__u32))); +static_assert(offsetof(struct serial_rs485, padding1) == + offsetof(struct serial_rs485, padding[1])); +static_assert((offsetof(struct serial_rs485, padding[4]) + sizeof(__u32)) == + sizeof(struct serial_rs485)); + MODULE_DESCRIPTION("Serial driver core"); MODULE_LICENSE("GPL"); diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index adae687f654b..2a76b330e108 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -319,6 +319,8 @@ unsigned char tty_get_frame_size(unsigned int cflag) bits++; if (cflag & PARENB) bits++; + if (cflag & ADDRB) + bits++; return bits; } @@ -353,6 +355,8 @@ int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) old_termios = tty->termios; tty->termios = *new_termios; unset_locked_termios(tty, &old_termios); + /* Reset any ADDRB changes, ADDRB is changed through ->rs485_config() */ + tty->termios.c_cflag ^= (tty->termios.c_cflag ^ old_termios.c_cflag) & ADDRB; if (tty->ops->set_termios) tty->ops->set_termios(tty, &old_termios); diff --git a/include/uapi/asm-generic/termbits-common.h b/include/uapi/asm-generic/termbits-common.h index 4d084fe8def5..4a6a79f28b21 100644 --- a/include/uapi/asm-generic/termbits-common.h +++ b/include/uapi/asm-generic/termbits-common.h @@ -46,6 +46,7 @@ typedef unsigned int speed_t; #define EXTA B19200 #define EXTB B38400 +#define ADDRB 0x20000000 /* address bit */ #define CMSPAR 0x40000000 /* mark or space (stick) parity */ #define CRTSCTS 0x80000000 /* flow control */ diff --git a/include/uapi/linux/serial.h b/include/uapi/linux/serial.h index fa6b16e5fdd8..cea06924b295 100644 --- a/include/uapi/linux/serial.h +++ b/include/uapi/linux/serial.h @@ -126,10 +126,26 @@ struct serial_rs485 { #define SER_RS485_TERMINATE_BUS (1 << 5) /* Enable bus termination (if supported) */ + +/* RS-485 addressing mode */ +#define SER_RS485_ADDRB (1 << 6) /* Enable addressing mode */ +#define SER_RS485_ADDR_RECV (1 << 7) /* Receive address filter */ +#define SER_RS485_ADDR_DEST (1 << 8) /* Destination address */ + __u32 delay_rts_before_send; /* Delay before send (milliseconds) */ __u32 delay_rts_after_send; /* Delay after send (milliseconds) */ - __u32 padding[5]; /* Memory is cheap, new structs - are a royal PITA .. */ + + /* The fields below are defined by flags */ + union { + __u32 padding[5]; /* Memory is cheap, new structs are a pain */ + + struct { + __u8 addr_recv; + __u8 addr_dest; + __u8 padding0[2]; + __u32 padding1[4]; + }; + }; }; /* -- cgit v1.2.3-59-g8ed1b From ceefa81e6e69b020997205e5c30a42d43aa5ae63 Mon Sep 17 00:00:00 2001 From: Thomas Bogendoerfer Date: Fri, 15 Jul 2022 16:03:22 +0200 Subject: serial: remove VR41XX serial driver Commit d3164e2f3b0a ("MIPS: Remove VR41xx support") removed support for MIPS VR41xx platform, so remove exclusive drivers for this platform, too. Signed-off-by: Thomas Bogendoerfer Link: https://lore.kernel.org/r/20220715140322.135825-1-tsbogend@alpha.franken.de Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/Kconfig | 17 - drivers/tty/serial/Makefile | 1 - drivers/tty/serial/vr41xx_siu.c | 932 --------------------------------------- include/uapi/linux/serial_core.h | 4 - 4 files changed, 954 deletions(-) delete mode 100644 drivers/tty/serial/vr41xx_siu.c (limited to 'include/uapi/linux') diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 8a3ee1525d80..f92963a2226b 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -890,23 +890,6 @@ config SERIAL_TXX9_STDSERIAL bool "TX39XX/49XX SIO act as standard serial" depends on !SERIAL_8250 && SERIAL_TXX9 -config SERIAL_VR41XX - tristate "NEC VR4100 series Serial Interface Unit support" - depends on CPU_VR41XX - select SERIAL_CORE - help - If you have a NEC VR4100 series processor and you want to use - Serial Interface Unit(SIU) or Debug Serial Interface Unit(DSIU) - (not include VR4111/VR4121 DSIU), say Y. Otherwise, say N. - -config SERIAL_VR41XX_CONSOLE - bool "Enable NEC VR4100 series Serial Interface Unit console" - depends on SERIAL_VR41XX=y - select SERIAL_CORE_CONSOLE - help - If you have a NEC VR4100 series processor and you want to use - a console on a serial port, say Y. Otherwise, say N. - config SERIAL_JSM tristate "Digi International NEO and Classic PCI Support" depends on PCI diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index 61cc8de95571..238a9557b487 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -51,7 +51,6 @@ obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o obj-$(CONFIG_SERIAL_JSM) += jsm/ obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o -obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o obj-$(CONFIG_SERIAL_MSM) += msm_serial.o diff --git a/drivers/tty/serial/vr41xx_siu.c b/drivers/tty/serial/vr41xx_siu.c deleted file mode 100644 index 1ba689a81abd..000000000000 --- a/drivers/tty/serial/vr41xx_siu.c +++ /dev/null @@ -1,932 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Driver for NEC VR4100 series Serial Interface Unit. - * - * Copyright (C) 2004-2008 Yoichi Yuasa - * - * Based on drivers/serial/8250.c, by Russell King. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#define SIU_BAUD_BASE 1152000 -#define SIU_MAJOR 204 -#define SIU_MINOR_BASE 82 - -#define RX_MAX_COUNT 256 -#define TX_MAX_COUNT 15 - -#define SIUIRSEL 0x08 - #define TMICMODE 0x20 - #define TMICTX 0x10 - #define IRMSEL 0x0c - #define IRMSEL_HP 0x08 - #define IRMSEL_TEMIC 0x04 - #define IRMSEL_SHARP 0x00 - #define IRUSESEL 0x02 - #define SIRSEL 0x01 - -static struct uart_port siu_uart_ports[SIU_PORTS_MAX] = { - [0 ... SIU_PORTS_MAX-1] = { - .lock = __SPIN_LOCK_UNLOCKED(siu_uart_ports->lock), - .irq = 0, - }, -}; - -#ifdef CONFIG_SERIAL_VR41XX_CONSOLE -static uint8_t lsr_break_flag[SIU_PORTS_MAX]; -#endif - -#define siu_read(port, offset) readb((port)->membase + (offset)) -#define siu_write(port, offset, value) writeb((value), (port)->membase + (offset)) - -void vr41xx_select_siu_interface(siu_interface_t interface) -{ - struct uart_port *port; - unsigned long flags; - uint8_t irsel; - - port = &siu_uart_ports[0]; - - spin_lock_irqsave(&port->lock, flags); - - irsel = siu_read(port, SIUIRSEL); - if (interface == SIU_INTERFACE_IRDA) - irsel |= SIRSEL; - else - irsel &= ~SIRSEL; - siu_write(port, SIUIRSEL, irsel); - - spin_unlock_irqrestore(&port->lock, flags); -} -EXPORT_SYMBOL_GPL(vr41xx_select_siu_interface); - -void vr41xx_use_irda(irda_use_t use) -{ - struct uart_port *port; - unsigned long flags; - uint8_t irsel; - - port = &siu_uart_ports[0]; - - spin_lock_irqsave(&port->lock, flags); - - irsel = siu_read(port, SIUIRSEL); - if (use == FIR_USE_IRDA) - irsel |= IRUSESEL; - else - irsel &= ~IRUSESEL; - siu_write(port, SIUIRSEL, irsel); - - spin_unlock_irqrestore(&port->lock, flags); -} -EXPORT_SYMBOL_GPL(vr41xx_use_irda); - -void vr41xx_select_irda_module(irda_module_t module, irda_speed_t speed) -{ - struct uart_port *port; - unsigned long flags; - uint8_t irsel; - - port = &siu_uart_ports[0]; - - spin_lock_irqsave(&port->lock, flags); - - irsel = siu_read(port, SIUIRSEL); - irsel &= ~(IRMSEL | TMICTX | TMICMODE); - switch (module) { - case SHARP_IRDA: - irsel |= IRMSEL_SHARP; - break; - case TEMIC_IRDA: - irsel |= IRMSEL_TEMIC | TMICMODE; - if (speed == IRDA_TX_4MBPS) - irsel |= TMICTX; - break; - case HP_IRDA: - irsel |= IRMSEL_HP; - break; - default: - break; - } - siu_write(port, SIUIRSEL, irsel); - - spin_unlock_irqrestore(&port->lock, flags); -} -EXPORT_SYMBOL_GPL(vr41xx_select_irda_module); - -static inline void siu_clear_fifo(struct uart_port *port) -{ - siu_write(port, UART_FCR, UART_FCR_ENABLE_FIFO); - siu_write(port, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | - UART_FCR_CLEAR_XMIT); - siu_write(port, UART_FCR, 0); -} - -static inline unsigned long siu_port_size(struct uart_port *port) -{ - switch (port->type) { - case PORT_VR41XX_SIU: - return 11UL; - case PORT_VR41XX_DSIU: - return 8UL; - } - - return 0; -} - -static inline unsigned int siu_check_type(struct uart_port *port) -{ - if (port->line == 0) - return PORT_VR41XX_SIU; - if (port->line == 1 && port->irq) - return PORT_VR41XX_DSIU; - - return PORT_UNKNOWN; -} - -static inline const char *siu_type_name(struct uart_port *port) -{ - switch (port->type) { - case PORT_VR41XX_SIU: - return "SIU"; - case PORT_VR41XX_DSIU: - return "DSIU"; - } - - return NULL; -} - -static unsigned int siu_tx_empty(struct uart_port *port) -{ - uint8_t lsr; - - lsr = siu_read(port, UART_LSR); - if (lsr & UART_LSR_TEMT) - return TIOCSER_TEMT; - - return 0; -} - -static void siu_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - uint8_t mcr = 0; - - if (mctrl & TIOCM_DTR) - mcr |= UART_MCR_DTR; - if (mctrl & TIOCM_RTS) - mcr |= UART_MCR_RTS; - if (mctrl & TIOCM_OUT1) - mcr |= UART_MCR_OUT1; - if (mctrl & TIOCM_OUT2) - mcr |= UART_MCR_OUT2; - if (mctrl & TIOCM_LOOP) - mcr |= UART_MCR_LOOP; - - siu_write(port, UART_MCR, mcr); -} - -static unsigned int siu_get_mctrl(struct uart_port *port) -{ - uint8_t msr; - unsigned int mctrl = 0; - - msr = siu_read(port, UART_MSR); - if (msr & UART_MSR_DCD) - mctrl |= TIOCM_CAR; - if (msr & UART_MSR_RI) - mctrl |= TIOCM_RNG; - if (msr & UART_MSR_DSR) - mctrl |= TIOCM_DSR; - if (msr & UART_MSR_CTS) - mctrl |= TIOCM_CTS; - - return mctrl; -} - -static void siu_stop_tx(struct uart_port *port) -{ - unsigned long flags; - uint8_t ier; - - spin_lock_irqsave(&port->lock, flags); - - ier = siu_read(port, UART_IER); - ier &= ~UART_IER_THRI; - siu_write(port, UART_IER, ier); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void siu_start_tx(struct uart_port *port) -{ - unsigned long flags; - uint8_t ier; - - spin_lock_irqsave(&port->lock, flags); - - ier = siu_read(port, UART_IER); - ier |= UART_IER_THRI; - siu_write(port, UART_IER, ier); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void siu_stop_rx(struct uart_port *port) -{ - unsigned long flags; - uint8_t ier; - - spin_lock_irqsave(&port->lock, flags); - - ier = siu_read(port, UART_IER); - ier &= ~UART_IER_RLSI; - siu_write(port, UART_IER, ier); - - port->read_status_mask &= ~UART_LSR_DR; - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void siu_enable_ms(struct uart_port *port) -{ - unsigned long flags; - uint8_t ier; - - spin_lock_irqsave(&port->lock, flags); - - ier = siu_read(port, UART_IER); - ier |= UART_IER_MSI; - siu_write(port, UART_IER, ier); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void siu_break_ctl(struct uart_port *port, int ctl) -{ - unsigned long flags; - uint8_t lcr; - - spin_lock_irqsave(&port->lock, flags); - - lcr = siu_read(port, UART_LCR); - if (ctl == -1) - lcr |= UART_LCR_SBC; - else - lcr &= ~UART_LCR_SBC; - siu_write(port, UART_LCR, lcr); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static inline void receive_chars(struct uart_port *port, uint8_t *status) -{ - uint8_t lsr, ch; - char flag; - int max_count = RX_MAX_COUNT; - - lsr = *status; - - do { - ch = siu_read(port, UART_RX); - port->icount.rx++; - flag = TTY_NORMAL; - -#ifdef CONFIG_SERIAL_VR41XX_CONSOLE - lsr |= lsr_break_flag[port->line]; - lsr_break_flag[port->line] = 0; -#endif - if (unlikely(lsr & (UART_LSR_BI | UART_LSR_FE | - UART_LSR_PE | UART_LSR_OE))) { - if (lsr & UART_LSR_BI) { - lsr &= ~(UART_LSR_FE | UART_LSR_PE); - port->icount.brk++; - - if (uart_handle_break(port)) - goto ignore_char; - } - - if (lsr & UART_LSR_FE) - port->icount.frame++; - if (lsr & UART_LSR_PE) - port->icount.parity++; - if (lsr & UART_LSR_OE) - port->icount.overrun++; - - lsr &= port->read_status_mask; - if (lsr & UART_LSR_BI) - flag = TTY_BREAK; - if (lsr & UART_LSR_FE) - flag = TTY_FRAME; - if (lsr & UART_LSR_PE) - flag = TTY_PARITY; - } - - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); - - ignore_char: - lsr = siu_read(port, UART_LSR); - } while ((lsr & UART_LSR_DR) && (max_count-- > 0)); - - tty_flip_buffer_push(&port->state->port); - - *status = lsr; -} - -static inline void check_modem_status(struct uart_port *port) -{ - uint8_t msr; - - msr = siu_read(port, UART_MSR); - if ((msr & UART_MSR_ANY_DELTA) == 0) - return; - if (msr & UART_MSR_DDCD) - uart_handle_dcd_change(port, msr & UART_MSR_DCD); - if (msr & UART_MSR_TERI) - port->icount.rng++; - if (msr & UART_MSR_DDSR) - port->icount.dsr++; - if (msr & UART_MSR_DCTS) - uart_handle_cts_change(port, msr & UART_MSR_CTS); - - wake_up_interruptible(&port->state->port.delta_msr_wait); -} - -static inline void transmit_chars(struct uart_port *port) -{ - struct circ_buf *xmit; - int max_count = TX_MAX_COUNT; - - xmit = &port->state->xmit; - - if (port->x_char) { - siu_write(port, UART_TX, port->x_char); - port->icount.tx++; - port->x_char = 0; - return; - } - - if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { - siu_stop_tx(port); - return; - } - - do { - siu_write(port, UART_TX, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - if (uart_circ_empty(xmit)) - break; - } while (max_count-- > 0); - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - - if (uart_circ_empty(xmit)) - siu_stop_tx(port); -} - -static irqreturn_t siu_interrupt(int irq, void *dev_id) -{ - struct uart_port *port; - uint8_t iir, lsr; - - port = (struct uart_port *)dev_id; - - iir = siu_read(port, UART_IIR); - if (iir & UART_IIR_NO_INT) - return IRQ_NONE; - - lsr = siu_read(port, UART_LSR); - if (lsr & UART_LSR_DR) - receive_chars(port, &lsr); - - check_modem_status(port); - - if (lsr & UART_LSR_THRE) - transmit_chars(port); - - return IRQ_HANDLED; -} - -static int siu_startup(struct uart_port *port) -{ - int retval; - - if (port->membase == NULL) - return -ENODEV; - - siu_clear_fifo(port); - - (void)siu_read(port, UART_LSR); - (void)siu_read(port, UART_RX); - (void)siu_read(port, UART_IIR); - (void)siu_read(port, UART_MSR); - - if (siu_read(port, UART_LSR) == 0xff) - return -ENODEV; - - retval = request_irq(port->irq, siu_interrupt, 0, siu_type_name(port), port); - if (retval) - return retval; - - if (port->type == PORT_VR41XX_DSIU) - vr41xx_enable_dsiuint(DSIUINT_ALL); - - siu_write(port, UART_LCR, UART_LCR_WLEN8); - - spin_lock_irq(&port->lock); - siu_set_mctrl(port, port->mctrl); - spin_unlock_irq(&port->lock); - - siu_write(port, UART_IER, UART_IER_RLSI | UART_IER_RDI); - - (void)siu_read(port, UART_LSR); - (void)siu_read(port, UART_RX); - (void)siu_read(port, UART_IIR); - (void)siu_read(port, UART_MSR); - - return 0; -} - -static void siu_shutdown(struct uart_port *port) -{ - unsigned long flags; - uint8_t lcr; - - siu_write(port, UART_IER, 0); - - spin_lock_irqsave(&port->lock, flags); - - port->mctrl &= ~TIOCM_OUT2; - siu_set_mctrl(port, port->mctrl); - - spin_unlock_irqrestore(&port->lock, flags); - - lcr = siu_read(port, UART_LCR); - lcr &= ~UART_LCR_SBC; - siu_write(port, UART_LCR, lcr); - - siu_clear_fifo(port); - - (void)siu_read(port, UART_RX); - - if (port->type == PORT_VR41XX_DSIU) - vr41xx_disable_dsiuint(DSIUINT_ALL); - - free_irq(port->irq, port); -} - -static void siu_set_termios(struct uart_port *port, struct ktermios *new, - struct ktermios *old) -{ - tcflag_t c_cflag, c_iflag; - uint8_t lcr, fcr, ier; - unsigned int baud, quot; - unsigned long flags; - - c_cflag = new->c_cflag; - lcr = UART_LCR_WLEN(tty_get_char_size(c_cflag)); - - if (c_cflag & CSTOPB) - lcr |= UART_LCR_STOP; - if (c_cflag & PARENB) - lcr |= UART_LCR_PARITY; - if ((c_cflag & PARODD) != PARODD) - lcr |= UART_LCR_EPAR; - if (c_cflag & CMSPAR) - lcr |= UART_LCR_SPAR; - - baud = uart_get_baud_rate(port, new, old, 0, port->uartclk/16); - quot = uart_get_divisor(port, baud); - - fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10; - - spin_lock_irqsave(&port->lock, flags); - - uart_update_timeout(port, c_cflag, baud); - - c_iflag = new->c_iflag; - - port->read_status_mask = UART_LSR_THRE | UART_LSR_OE | UART_LSR_DR; - if (c_iflag & INPCK) - port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (c_iflag & (IGNBRK | BRKINT | PARMRK)) - port->read_status_mask |= UART_LSR_BI; - - port->ignore_status_mask = 0; - if (c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (c_iflag & IGNBRK) { - port->ignore_status_mask |= UART_LSR_BI; - if (c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_OE; - } - - if ((c_cflag & CREAD) == 0) - port->ignore_status_mask |= UART_LSR_DR; - - ier = siu_read(port, UART_IER); - ier &= ~UART_IER_MSI; - if (UART_ENABLE_MS(port, c_cflag)) - ier |= UART_IER_MSI; - siu_write(port, UART_IER, ier); - - siu_write(port, UART_LCR, lcr | UART_LCR_DLAB); - - siu_write(port, UART_DLL, (uint8_t)quot); - siu_write(port, UART_DLM, (uint8_t)(quot >> 8)); - - siu_write(port, UART_LCR, lcr); - - siu_write(port, UART_FCR, fcr); - - siu_set_mctrl(port, port->mctrl); - - spin_unlock_irqrestore(&port->lock, flags); -} - -static void siu_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) -{ - switch (state) { - case 0: - switch (port->type) { - case PORT_VR41XX_SIU: - vr41xx_supply_clock(SIU_CLOCK); - break; - case PORT_VR41XX_DSIU: - vr41xx_supply_clock(DSIU_CLOCK); - break; - } - break; - case 3: - switch (port->type) { - case PORT_VR41XX_SIU: - vr41xx_mask_clock(SIU_CLOCK); - break; - case PORT_VR41XX_DSIU: - vr41xx_mask_clock(DSIU_CLOCK); - break; - } - break; - } -} - -static const char *siu_type(struct uart_port *port) -{ - return siu_type_name(port); -} - -static void siu_release_port(struct uart_port *port) -{ - unsigned long size; - - if (port->flags & UPF_IOREMAP) { - iounmap(port->membase); - port->membase = NULL; - } - - size = siu_port_size(port); - release_mem_region(port->mapbase, size); -} - -static int siu_request_port(struct uart_port *port) -{ - unsigned long size; - struct resource *res; - - size = siu_port_size(port); - res = request_mem_region(port->mapbase, size, siu_type_name(port)); - if (res == NULL) - return -EBUSY; - - if (port->flags & UPF_IOREMAP) { - port->membase = ioremap(port->mapbase, size); - if (port->membase == NULL) { - release_resource(res); - return -ENOMEM; - } - } - - return 0; -} - -static void siu_config_port(struct uart_port *port, int flags) -{ - if (flags & UART_CONFIG_TYPE) { - port->type = siu_check_type(port); - (void)siu_request_port(port); - } -} - -static int siu_verify_port(struct uart_port *port, struct serial_struct *serial) -{ - if (port->type != PORT_VR41XX_SIU && port->type != PORT_VR41XX_DSIU) - return -EINVAL; - if (port->irq != serial->irq) - return -EINVAL; - if (port->iotype != serial->io_type) - return -EINVAL; - if (port->mapbase != (unsigned long)serial->iomem_base) - return -EINVAL; - - return 0; -} - -static const struct uart_ops siu_uart_ops = { - .tx_empty = siu_tx_empty, - .set_mctrl = siu_set_mctrl, - .get_mctrl = siu_get_mctrl, - .stop_tx = siu_stop_tx, - .start_tx = siu_start_tx, - .stop_rx = siu_stop_rx, - .enable_ms = siu_enable_ms, - .break_ctl = siu_break_ctl, - .startup = siu_startup, - .shutdown = siu_shutdown, - .set_termios = siu_set_termios, - .pm = siu_pm, - .type = siu_type, - .release_port = siu_release_port, - .request_port = siu_request_port, - .config_port = siu_config_port, - .verify_port = siu_verify_port, -}; - -static int siu_init_ports(struct platform_device *pdev) -{ - struct uart_port *port; - struct resource *res; - int *type = dev_get_platdata(&pdev->dev); - int i; - - if (!type) - return 0; - - port = siu_uart_ports; - for (i = 0; i < SIU_PORTS_MAX; i++) { - port->type = type[i]; - if (port->type == PORT_UNKNOWN) - continue; - port->irq = platform_get_irq(pdev, i); - port->uartclk = SIU_BAUD_BASE * 16; - port->fifosize = 16; - port->regshift = 0; - port->iotype = UPIO_MEM; - port->flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF; - port->line = i; - res = platform_get_resource(pdev, IORESOURCE_MEM, i); - port->mapbase = res->start; - port++; - } - - return i; -} - -#ifdef CONFIG_SERIAL_VR41XX_CONSOLE - -static void wait_for_xmitr(struct uart_port *port) -{ - int timeout = 10000; - uint8_t lsr, msr; - - do { - lsr = siu_read(port, UART_LSR); - if (lsr & UART_LSR_BI) - lsr_break_flag[port->line] = UART_LSR_BI; - - if (uart_lsr_tx_empty(lsr)) - break; - } while (timeout-- > 0); - - if (port->flags & UPF_CONS_FLOW) { - timeout = 1000000; - - do { - msr = siu_read(port, UART_MSR); - if ((msr & UART_MSR_CTS) != 0) - break; - } while (timeout-- > 0); - } -} - -static void siu_console_putchar(struct uart_port *port, unsigned char ch) -{ - wait_for_xmitr(port); - siu_write(port, UART_TX, ch); -} - -static void siu_console_write(struct console *con, const char *s, unsigned count) -{ - struct uart_port *port; - uint8_t ier; - - port = &siu_uart_ports[con->index]; - - ier = siu_read(port, UART_IER); - siu_write(port, UART_IER, 0); - - uart_console_write(port, s, count, siu_console_putchar); - - wait_for_xmitr(port); - siu_write(port, UART_IER, ier); -} - -static int __init siu_console_setup(struct console *con, char *options) -{ - struct uart_port *port; - int baud = 9600; - int parity = 'n'; - int bits = 8; - int flow = 'n'; - - if (con->index >= SIU_PORTS_MAX) - con->index = 0; - - port = &siu_uart_ports[con->index]; - if (port->membase == NULL) { - if (port->mapbase == 0) - return -ENODEV; - port->membase = ioremap(port->mapbase, siu_port_size(port)); - } - - if (port->type == PORT_VR41XX_SIU) - vr41xx_select_siu_interface(SIU_INTERFACE_RS232C); - - if (options != NULL) - uart_parse_options(options, &baud, &parity, &bits, &flow); - - return uart_set_options(port, con, baud, parity, bits, flow); -} - -static struct uart_driver siu_uart_driver; - -static struct console siu_console = { - .name = "ttyVR", - .write = siu_console_write, - .device = uart_console_device, - .setup = siu_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &siu_uart_driver, -}; - -static int siu_console_init(void) -{ - struct uart_port *port; - int i; - - for (i = 0; i < SIU_PORTS_MAX; i++) { - port = &siu_uart_ports[i]; - port->ops = &siu_uart_ops; - } - - register_console(&siu_console); - - return 0; -} - -console_initcall(siu_console_init); - -void __init vr41xx_siu_early_setup(struct uart_port *port) -{ - if (port->type == PORT_UNKNOWN) - return; - - siu_uart_ports[port->line].line = port->line; - siu_uart_ports[port->line].type = port->type; - siu_uart_ports[port->line].uartclk = SIU_BAUD_BASE * 16; - siu_uart_ports[port->line].mapbase = port->mapbase; - siu_uart_ports[port->line].ops = &siu_uart_ops; -} - -#define SERIAL_VR41XX_CONSOLE &siu_console -#else -#define SERIAL_VR41XX_CONSOLE NULL -#endif - -static struct uart_driver siu_uart_driver = { - .owner = THIS_MODULE, - .driver_name = "SIU", - .dev_name = "ttyVR", - .major = SIU_MAJOR, - .minor = SIU_MINOR_BASE, - .cons = SERIAL_VR41XX_CONSOLE, -}; - -static int siu_probe(struct platform_device *dev) -{ - struct uart_port *port; - int num, i, retval; - - num = siu_init_ports(dev); - if (num <= 0) - return -ENODEV; - - siu_uart_driver.nr = num; - retval = uart_register_driver(&siu_uart_driver); - if (retval) - return retval; - - for (i = 0; i < num; i++) { - port = &siu_uart_ports[i]; - port->ops = &siu_uart_ops; - port->dev = &dev->dev; - port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_VR41XX_CONSOLE); - - retval = uart_add_one_port(&siu_uart_driver, port); - if (retval < 0) { - port->dev = NULL; - break; - } - } - - if (i == 0 && retval < 0) { - uart_unregister_driver(&siu_uart_driver); - return retval; - } - - return 0; -} - -static int siu_remove(struct platform_device *dev) -{ - struct uart_port *port; - int i; - - for (i = 0; i < siu_uart_driver.nr; i++) { - port = &siu_uart_ports[i]; - if (port->dev == &dev->dev) { - uart_remove_one_port(&siu_uart_driver, port); - port->dev = NULL; - } - } - - uart_unregister_driver(&siu_uart_driver); - - return 0; -} - -static int siu_suspend(struct platform_device *dev, pm_message_t state) -{ - struct uart_port *port; - int i; - - for (i = 0; i < siu_uart_driver.nr; i++) { - port = &siu_uart_ports[i]; - if ((port->type == PORT_VR41XX_SIU || - port->type == PORT_VR41XX_DSIU) && port->dev == &dev->dev) - uart_suspend_port(&siu_uart_driver, port); - - } - - return 0; -} - -static int siu_resume(struct platform_device *dev) -{ - struct uart_port *port; - int i; - - for (i = 0; i < siu_uart_driver.nr; i++) { - port = &siu_uart_ports[i]; - if ((port->type == PORT_VR41XX_SIU || - port->type == PORT_VR41XX_DSIU) && port->dev == &dev->dev) - uart_resume_port(&siu_uart_driver, port); - } - - return 0; -} - -static struct platform_driver siu_device_driver = { - .probe = siu_probe, - .remove = siu_remove, - .suspend = siu_suspend, - .resume = siu_resume, - .driver = { - .name = "SIU", - }, -}; - -module_platform_driver(siu_device_driver); - -MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:SIU"); diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h index 6faf502b7860..3ba34d8378bd 100644 --- a/include/uapi/linux/serial_core.h +++ b/include/uapi/linux/serial_core.h @@ -124,10 +124,6 @@ /* TXX9 type number */ #define PORT_TXX9 64 -/* NEC VR4100 series SIU/DSIU */ -#define PORT_VR41XX_SIU 65 -#define PORT_VR41XX_DSIU 66 - /* Samsung S3C2400 SoC */ #define PORT_S3C2400 67 -- cgit v1.2.3-59-g8ed1b