From f3f3149f35b9195ef4b761b1353fc0766b5f53be Mon Sep 17 00:00:00 2001 From: Alok Kataria Date: Mon, 23 Jun 2008 18:21:56 -0700 Subject: x86: use cpu_khz for loops_per_jiffy calculation, cleanup As suggested by Ingo, remove all references to tsc from init/calibrate.c TSC is x86 specific, and using tsc in variable names in a generic file should be avoided. lpj_tsc is now called lpj_fine, since it is related to fine tuning of lpj value. Also tsc_rate_* is called timer_rate_* Signed-off-by: Alok N Kataria Cc: Arjan van de Ven Cc: Daniel Hecht Cc: Tim Mann Cc: Zach Amsden Cc: Sahil Rihan Signed-off-by: Ingo Molnar --- init/calibrate.c | 36 +++++++++++++++++++----------------- 1 file changed, 19 insertions(+), 17 deletions(-) (limited to 'init/calibrate.c') diff --git a/init/calibrate.c b/init/calibrate.c index 86286974dada..7963e3fc51d9 100644 --- a/init/calibrate.c +++ b/init/calibrate.c @@ -10,7 +10,7 @@ #include #include -unsigned long lpj_tsc; +unsigned long lpj_fine; unsigned long preset_lpj; static int __init lpj_setup(char *str) { @@ -35,9 +35,9 @@ static unsigned long __cpuinit calibrate_delay_direct(void) unsigned long pre_start, start, post_start; unsigned long pre_end, end, post_end; unsigned long start_jiffies; - unsigned long tsc_rate_min, tsc_rate_max; - unsigned long good_tsc_sum = 0; - unsigned long good_tsc_count = 0; + unsigned long timer_rate_min, timer_rate_max; + unsigned long good_timer_sum = 0; + unsigned long good_timer_count = 0; int i; if (read_current_timer(&pre_start) < 0 ) @@ -81,22 +81,24 @@ static unsigned long __cpuinit calibrate_delay_direct(void) } read_current_timer(&post_end); - tsc_rate_max = (post_end - pre_start) / DELAY_CALIBRATION_TICKS; - tsc_rate_min = (pre_end - post_start) / DELAY_CALIBRATION_TICKS; + timer_rate_max = (post_end - pre_start) / + DELAY_CALIBRATION_TICKS; + timer_rate_min = (pre_end - post_start) / + DELAY_CALIBRATION_TICKS; /* - * If the upper limit and lower limit of the tsc_rate is + * If the upper limit and lower limit of the timer_rate is * >= 12.5% apart, redo calibration. */ if (pre_start != 0 && pre_end != 0 && - (tsc_rate_max - tsc_rate_min) < (tsc_rate_max >> 3)) { - good_tsc_count++; - good_tsc_sum += tsc_rate_max; + (timer_rate_max - timer_rate_min) < (timer_rate_max >> 3)) { + good_timer_count++; + good_timer_sum += timer_rate_max; } } - if (good_tsc_count) - return (good_tsc_sum/good_tsc_count); + if (good_timer_count) + return (good_timer_sum/good_timer_count); printk(KERN_WARNING "calibrate_delay_direct() failed to get a good " "estimate for loops_per_jiffy.\nProbably due to long platform interrupts. Consider using \"lpj=\" boot option.\n"); @@ -111,8 +113,8 @@ static unsigned long __cpuinit calibrate_delay_direct(void) {return 0;} * bit takes on average 1.5/HZ seconds. This (like the original) is a little * better than 1% * For the boot cpu we can skip the delay calibration and assign it a value - * calculated based on the tsc frequency. - * For the rest of the CPUs we cannot assume that the tsc frequency is same as + * calculated based on the timer frequency. + * For the rest of the CPUs we cannot assume that the timer frequency is same as * the cpu frequency, hence do the calibration for those. */ #define LPS_PREC 8 @@ -126,11 +128,11 @@ void __cpuinit calibrate_delay(void) loops_per_jiffy = preset_lpj; printk(KERN_INFO "Calibrating delay loop (skipped) preset value.. "); - } else if ((smp_processor_id() == 0) && lpj_tsc) { - loops_per_jiffy = lpj_tsc; + } else if ((smp_processor_id() == 0) && lpj_fine) { + loops_per_jiffy = lpj_fine; printk(KERN_INFO "Calibrating delay loop (skipped), " - "using tsc calculated value.. "); + "value calculated using timer frequency.. "); } else if ((loops_per_jiffy = calibrate_delay_direct()) != 0) { printk(KERN_INFO "Calibrating delay using timer specific routine.. "); -- cgit v1.2.3-59-g8ed1b