Kernel driver ds1621 ==================== Supported chips: * Dallas Semiconductor / Maxim Integrated DS1621 Prefix: 'ds1621' Addresses scanned: none Datasheet: Publicly available from www.maximintegrated.com * Dallas Semiconductor DS1625 Prefix: 'ds1625' Addresses scanned: none Datasheet: Publicly available from www.datasheetarchive.com * Maxim Integrated DS1631 Prefix: 'ds1631' Addresses scanned: none Datasheet: Publicly available from www.maximintegrated.com * Maxim Integrated DS1721 Prefix: 'ds1721' Addresses scanned: none Datasheet: Publicly available from www.maximintegrated.com * Maxim Integrated DS1731 Prefix: 'ds1731' Addresses scanned: none Datasheet: Publicly available from www.maximintegrated.com Authors: Christian W. Zuckschwerdt valuable contributions by Jan M. Sendler ported to 2.6 by Aurelien Jarno with the help of Jean Delvare Module Parameters ------------------ * polarity int Output's polarity: 0 = active high, 1 = active low Description ----------- The DS1621 is a (one instance) digital thermometer and thermostat. It has both high and low temperature limits which can be user defined (i.e. programmed into non-volatile on-chip registers). Temperature range is -55 degree Celsius to +125 in 0.5 increments. You may convert this into a Fahrenheit range of -67 to +257 degrees with 0.9 steps. If polarity parameter is not provided, original value is used. As for the thermostat, behavior can also be programmed using the polarity toggle. On the one hand ("heater"), the thermostat output of the chip, Tout, will trigger when the low limit temperature is met or underrun and stays high until the high limit is met or exceeded. On the other hand ("cooler"), vice versa. That way "heater" equals "active low", whereas "conditioner" equals "active high". Please note that the DS1621 data sheet is somewhat misleading in this point since setting the polarity bit does not simply invert Tout. A second thing is that, during extensive testing, Tout showed a tolerance of up to +/- 0.5 degrees even when compared against precise temperature readings. Be sure to have a high vs. low temperature limit gap of al least 1.0 degree Celsius to avoid Tout "bouncing", though! The alarm bits are set when the high or low limits are met or exceeded and are reset by the module as soon as the respective temperature ranges are left. The alarm registers are in no way suitable to find out about the actual status of Tout. They will only tell you about its history, whether or not any of the limits have ever been met or exceeded since last power-up or reset. Be aware: When testing, it showed that the status of Tout can change with neither of the alarms set. Temperature conversion of the DS1621 takes up to 1000ms; internal access to non-volatile registers may last for 10ms or below. The DS1625 is pin compatible and functionally equivalent with the DS1621, but the DS1621 is meant to replace it. The DS1631, DS1721, and DS1731 are also pin compatible with the DS1621, but provide multi-resolution support. Since there is no version or vendor identification register, there is no unique identification for these devices. Therefore, explicit device instantiation is required for correct device identification and functionality. And, for correct identification and operation, each device must be explicitly instantiated, one device per address, in this address range: 0x48..0x4f. The DS1721 is pin compatible with the DS1621, has an accuracy of +/- 1.0 degree Celsius (from -10 to +85 degrees), a minimum/maximum alarm default setting of 75 and 80 degrees, and a maximum conversion time of 750ms. In addition, the DS1721 supports four resolution settings from 9 to 12 bits (defined in degrees C per LSB: 0.5, 0.25, 0.125, and 0.0625, respectively), that are set at device power on to the highest resolution: 12-bits. One additional note about the ds1721 is that although the data sheet says the temperature flags (THF and TLF) are used internally, these flags do get set and cleared as the actual temperature crosses the min or max settings. The DS1631 and DS1731 are pin compatible with the DS1621 and feature compatible with the DS1721. However, the DS1631 accuracy is +/- 0.5 degree Celsius (from 0 to +70 degrees), while the DS1731 accuracy is +/-1 degree Celsius (from -10 to +85 degrees). The resolution mode for the DS1631, DS1721, or DS1731 can be changed from userspace, via the device 'update_interval' sysfs attribute. This attribute will normalize the range of input values to the device maximum resolution values defined in the datasheet as follows: Resolution Conversion Time Input Range (C/LSB) (msec) (msec) -------------------------------------------- 0.5 93.75 0....94 0.25 187.5 95...187 0.125 375 188..375 0.0625 750 376..infinity -------------------------------------- The following examples show how the 'update_interval' attribute can be used to change the conversion time: $ cat update_interval 750 $ cat temp1_input 22062 $ $ echo 300 > update_interval $ cat update_interval 375 $ cat temp1_input 22125 $ $ echo 150 > update_interval $ cat update_interval 188 $ cat temp1_input 22250 $ $ echo 1 > update_interval $ cat update_interval 94 $ cat temp1_input 22000 $ $ echo 1000 > update_interval $ cat update_interval 750 $ cat temp1_input 22062 $ As shown, the ds1621 driver automatically adjusts the 'update_interval' user input, via a step function. Reading back the 'update_interval' value after a write operation provides the conversion time used by the device. Mathematically, the resolution can be derived from the conversion time via the following function: g(x) = 0.5 * [minimum_conversion_time/x] where: -> 'x' = the output from 'update_interval' -> 'g(x)' = the resolution in degrees C per LSB. -> 93.75ms = minimum conversion time