source "arch/powerpc/platforms/Kconfig.cputype" config PPC32 bool default y if !PPC64 config 32BIT bool default y if PPC32 config 64BIT bool default y if PPC64 config WORD_SIZE int default 64 if PPC64 default 32 if !PPC64 config ARCH_PHYS_ADDR_T_64BIT def_bool PPC64 || PHYS_64BIT config ARCH_DMA_ADDR_T_64BIT def_bool ARCH_PHYS_ADDR_T_64BIT config MMU bool default y config HAVE_SETUP_PER_CPU_AREA def_bool PPC64 config NEED_PER_CPU_EMBED_FIRST_CHUNK def_bool PPC64 config NR_IRQS int "Number of virtual interrupt numbers" range 32 32768 default "512" help This defines the number of virtual interrupt numbers the kernel can manage. Virtual interrupt numbers are what you see in /proc/interrupts. If you configure your system to have too few, drivers will fail to load or worse - handle with care. config STACKTRACE_SUPPORT bool default y config HAVE_LATENCYTOP_SUPPORT def_bool y config TRACE_IRQFLAGS_SUPPORT bool default y config LOCKDEP_SUPPORT bool default y config RWSEM_GENERIC_SPINLOCK bool config RWSEM_XCHGADD_ALGORITHM bool default y config GENERIC_LOCKBREAK bool default y depends on SMP && PREEMPT config ARCH_HAS_ILOG2_U32 bool default y config ARCH_HAS_ILOG2_U64 bool default y if 64BIT config GENERIC_HWEIGHT bool default y config PPC bool default y select ARCH_MIGHT_HAVE_PC_PARPORT select ARCH_MIGHT_HAVE_PC_SERIO select BINFMT_ELF select OF select OF_EARLY_FLATTREE select OF_RESERVED_MEM select HAVE_FTRACE_MCOUNT_RECORD select HAVE_DYNAMIC_FTRACE select HAVE_FUNCTION_TRACER select HAVE_FUNCTION_GRAPH_TRACER select SYSCTL_EXCEPTION_TRACE select ARCH_WANT_OPTIONAL_GPIOLIB select VIRT_TO_BUS if !PPC64 select HAVE_IDE select HAVE_IOREMAP_PROT select HAVE_EFFICIENT_UNALIGNED_ACCESS if !CPU_LITTLE_ENDIAN select HAVE_KPROBES select HAVE_ARCH_KGDB select HAVE_KRETPROBES select HAVE_ARCH_TRACEHOOK select HAVE_MEMBLOCK select HAVE_MEMBLOCK_NODE_MAP select HAVE_DMA_ATTRS select HAVE_DMA_API_DEBUG select HAVE_OPROFILE select HAVE_DEBUG_KMEMLEAK select GENERIC_ATOMIC64 if PPC32 select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select HAVE_PERF_EVENTS select HAVE_REGS_AND_STACK_ACCESS_API select HAVE_HW_BREAKPOINT if PERF_EVENTS && PPC_BOOK3S_64 select ARCH_WANT_IPC_PARSE_VERSION select SPARSE_IRQ select IRQ_DOMAIN select GENERIC_IRQ_SHOW select GENERIC_IRQ_SHOW_LEVEL select IRQ_FORCED_THREADING select HAVE_RCU_TABLE_FREE if SMP select HAVE_SYSCALL_TRACEPOINTS select HAVE_BPF_JIT if PPC64 select HAVE_ARCH_JUMP_LABEL select ARCH_HAVE_NMI_SAFE_CMPXCHG select GENERIC_SMP_IDLE_THREAD select GENERIC_CMOS_UPDATE select GENERIC_TIME_VSYSCALL_OLD select GENERIC_CLOCKEVENTS select GENERIC_CLOCKEVENTS_BROADCAST if SMP select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST select GENERIC_STRNCPY_FROM_USER select GENERIC_STRNLEN_USER select HAVE_MOD_ARCH_SPECIFIC select MODULES_USE_ELF_RELA select CLONE_BACKWARDS select ARCH_USE_BUILTIN_BSWAP select OLD_SIGSUSPEND select OLD_SIGACTION if PPC32 select HAVE_DEBUG_STACKOVERFLOW select HAVE_IRQ_EXIT_ON_IRQ_STACK select ARCH_USE_CMPXCHG_LOCKREF if PPC64 select HAVE_ARCH_AUDITSYSCALL config GENERIC_CSUM def_bool CPU_LITTLE_ENDIAN config EARLY_PRINTK bool default y config PANIC_TIMEOUT int default 180 config COMPAT bool default y if PPC64 select COMPAT_BINFMT_ELF select ARCH_WANT_OLD_COMPAT_IPC select COMPAT_OLD_SIGACTION config SYSVIPC_COMPAT bool depends on COMPAT && SYSVIPC default y # All PPC32s use generic nvram driver through ppc_md config GENERIC_NVRAM bool default y if PPC32 config SCHED_OMIT_FRAME_POINTER bool default y config ARCH_MAY_HAVE_PC_FDC bool default !PPC_PSERIES || PCI config PPC_OF def_bool y config PPC_UDBG_16550 bool default n config GENERIC_TBSYNC bool default y if PPC32 && SMP default n config AUDIT_ARCH bool default y config GENERIC_BUG bool default y depends on BUG config SYS_SUPPORTS_APM_EMULATION default y if PMAC_APM_EMU bool config EPAPR_BOOT bool help Used to allow a board to specify it wants an ePAPR compliant wrapper. default n config DEFAULT_UIMAGE bool help Used to allow a board to specify it wants a uImage built by default default n config ARCH_HIBERNATION_POSSIBLE bool default y config ARCH_SUSPEND_POSSIBLE def_bool y depends on ADB_PMU || PPC_EFIKA || PPC_LITE5200 || PPC_83xx || \ (PPC_85xx && !PPC_E500MC) || PPC_86xx || PPC_PSERIES \ || 44x || 40x config PPC_DCR_NATIVE bool default n config PPC_DCR_MMIO bool default n config PPC_DCR bool depends on PPC_DCR_NATIVE || PPC_DCR_MMIO default y config PPC_OF_PLATFORM_PCI bool depends on PCI depends on PPC64 # not supported on 32 bits yet default n config ARCH_SUPPORTS_DEBUG_PAGEALLOC def_bool y config ARCH_SUPPORTS_UPROBES def_bool y config PPC_ADV_DEBUG_REGS bool depends on 40x || BOOKE default y config PPC_ADV_DEBUG_IACS int depends on PPC_ADV_DEBUG_REGS default 4 if 44x default 2 config PPC_ADV_DEBUG_DACS int depends on PPC_ADV_DEBUG_REGS default 2 config PPC_ADV_DEBUG_DVCS int depends on PPC_ADV_DEBUG_REGS default 2 if 44x default 0 config PPC_ADV_DEBUG_DAC_RANGE bool depends on PPC_ADV_DEBUG_REGS && 44x default y config PPC_EMULATE_SSTEP bool default y if KPROBES || UPROBES || XMON || HAVE_HW_BREAKPOINT source "init/Kconfig" source "kernel/Kconfig.freezer" source "arch/powerpc/sysdev/Kconfig" source "arch/powerpc/platforms/Kconfig" menu "Kernel options" config HIGHMEM bool "High memory support" depends on PPC32 source kernel/Kconfig.hz source kernel/Kconfig.preempt source "fs/Kconfig.binfmt" config HUGETLB_PAGE_SIZE_VARIABLE bool depends on HUGETLB_PAGE default y config MATH_EMULATION bool "Math emulation" depends on 4xx || 8xx || PPC_MPC832x || BOOKE ---help--- Some PowerPC chips designed for embedded applications do not have a floating-point unit and therefore do not implement the floating-point instructions in the PowerPC instruction set. If you say Y here, the kernel will include code to emulate a floating-point unit, which will allow programs that use floating-point instructions to run. This is also useful to emulate missing (optional) instructions such as fsqrt on cores that do have an FPU but do not implement them (such as Freescale BookE). choice prompt "Math emulation options" default MATH_EMULATION_FULL depends on MATH_EMULATION config MATH_EMULATION_FULL bool "Emulate all the floating point instructions" ---help--- Select this option will enable the kernel to support to emulate all the floating point instructions. If your SoC doesn't have a FPU, you should select this. config MATH_EMULATION_HW_UNIMPLEMENTED bool "Just emulate the FPU unimplemented instructions" ---help--- Select this if you know there does have a hardware FPU on your SoC, but some floating point instructions are not implemented by that. endchoice config PPC_TRANSACTIONAL_MEM bool "Transactional Memory support for POWERPC" depends on PPC_BOOK3S_64 depends on SMP select ALTIVEC select VSX default n ---help--- Support user-mode Transactional Memory on POWERPC. config IOMMU_HELPER def_bool PPC64 config SWIOTLB bool "SWIOTLB support" default n select IOMMU_HELPER ---help--- Support for IO bounce buffering for systems without an IOMMU. This allows us to DMA to the full physical address space on platforms where the size of a physical address is larger than the bus address. Not all platforms support this. config HOTPLUG_CPU bool "Support for enabling/disabling CPUs" depends on SMP && (PPC_PSERIES || \ PPC_PMAC || PPC_POWERNV || (PPC_85xx && !PPC_E500MC)) ---help--- Say Y here to be able to disable and re-enable individual CPUs at runtime on SMP machines. Say N if you are unsure. config ARCH_CPU_PROBE_RELEASE def_bool y depends on HOTPLUG_CPU config ARCH_ENABLE_MEMORY_HOTPLUG def_bool y config ARCH_HAS_WALK_MEMORY def_bool y config ARCH_ENABLE_MEMORY_HOTREMOVE def_bool y config PPC64_SUPPORTS_MEMORY_FAILURE bool "Add support for memory hwpoison" depends on PPC_BOOK3S_64 default "y" if PPC_POWERNV select ARCH_SUPPORTS_MEMORY_FAILURE config KEXEC bool "kexec system call" depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP)) help kexec is a system call that implements the ability to shutdown your current kernel, and to start another kernel. It is like a reboot but it is independent of the system firmware. And like a reboot you can start any kernel with it, not just Linux. The name comes from the similarity to the exec system call. It is an ongoing process to be certain the hardware in a machine is properly shutdown, so do not be surprised if this code does not initially work for you. As of this writing the exact hardware interface is strongly in flux, so no good recommendation can be made. config CRASH_DUMP bool "Build a kdump crash kernel" depends on PPC64 || 6xx || FSL_BOOKE || (44x && !SMP) select RELOCATABLE if (PPC64 && !COMPILE_TEST) || 44x || FSL_BOOKE help Build a kernel suitable for use as a kdump capture kernel. The same kernel binary can be used as production kernel and dump capture kernel. config FA_DUMP bool "Firmware-assisted dump" depends on PPC64 && PPC_RTAS && CRASH_DUMP && KEXEC help A robust mechanism to get reliable kernel crash dump with assistance from firmware. This approach does not use kexec, instead firmware assists in booting the kdump kernel while preserving memory contents. Firmware-assisted dump is meant to be a kdump replacement offering robustness and speed not possible without system firmware assistance. If unsure, say "N" config IRQ_ALL_CPUS bool "Distribute interrupts on all CPUs by default" depends on SMP help This option gives the kernel permission to distribute IRQs across multiple CPUs. Saying N here will route all IRQs to the first CPU. Generally saying Y is safe, although some problems have been reported with SMP Power Macintoshes with this option enabled. config NUMA bool "NUMA support" depends on PPC64 default y if SMP && PPC_PSERIES config NODES_SHIFT int default "8" if PPC64 default "4" depends on NEED_MULTIPLE_NODES config USE_PERCPU_NUMA_NODE_ID def_bool y depends on NUMA config HAVE_MEMORYLESS_NODES def_bool y depends on NUMA config ARCH_SELECT_MEMORY_MODEL def_bool y depends on PPC64 config ARCH_FLATMEM_ENABLE def_bool y depends on (PPC64 && !NUMA) || PPC32 config ARCH_SPARSEMEM_ENABLE def_bool y depends on PPC64 select SPARSEMEM_VMEMMAP_ENABLE config ARCH_SPARSEMEM_DEFAULT def_bool y depends on (SMP && PPC_PSERIES) || PPC_PS3 config SYS_SUPPORTS_HUGETLBFS bool source "mm/Kconfig" config ARCH_MEMORY_PROBE def_bool y depends on MEMORY_HOTPLUG # Some NUMA nodes have memory ranges that span # other nodes. Even though a pfn is valid and # between a node's start and end pfns, it may not # reside on that node. See memmap_init_zone() # for details. config NODES_SPAN_OTHER_NODES def_bool y depends on NEED_MULTIPLE_NODES config PPC_HAS_HASH_64K bool depends on PPC64 default n config STDBINUTILS bool "Using standard binutils settings" depends on 44x default y help Turning this option off allows you to select 256KB PAGE_SIZE on 44x. Note, that kernel will be able to run only those applications, which had been compiled using binutils later than 2.17.50.0.3 with '-zmax-page-size' set to 256K (the default is 64K). Or, if using the older binutils, you can patch them with a trivial patch, which changes the ELF_MAXPAGESIZE definition from 0x10000 to 0x40000. choice prompt "Page size" default PPC_4K_PAGES help Select the kernel logical page size. Increasing the page size will reduce software overhead at each page boundary, allow hardware prefetch mechanisms to be more effective, and allow larger dma transfers increasing IO efficiency and reducing overhead. However the utilization of memory will increase. For example, each cached file will using a multiple of the page size to hold its contents and the difference between the end of file and the end of page is wasted. Some dedicated systems, such as software raid serving with accelerated calculations, have shown significant increases. If you configure a 64 bit kernel for 64k pages but the processor does not support them, then the kernel will simulate them with 4k pages, loading them on demand, but with the reduced software overhead and larger internal fragmentation. For the 32 bit kernel, a large page option will not be offered unless it is supported by the configured processor. If unsure, choose 4K_PAGES. config PPC_4K_PAGES bool "4k page size" config PPC_16K_PAGES bool "16k page size" if 44x config PPC_64K_PAGES bool "64k page size" if 44x || PPC_STD_MMU_64 || PPC_BOOK3E_64 depends on !PPC_FSL_BOOK3E select PPC_HAS_HASH_64K if PPC_STD_MMU_64 config PPC_256K_PAGES bool "256k page size" if 44x depends on !STDBINUTILS help Make the page size 256k. As the ELF standard only requires alignment to support page sizes up to 64k, you will need to compile all of your user space applications with a non-standard binutils settings (see the STDBINUTILS description for details). Say N unless you know what you are doing. endchoice config FORCE_MAX_ZONEORDER int "Maximum zone order" range 9 64 if PPC64 && PPC_64K_PAGES default "9" if PPC64 && PPC_64K_PAGES range 13 64 if PPC64 && !PPC_64K_PAGES default "13" if PPC64 && !PPC_64K_PAGES range 9 64 if PPC32 && PPC_16K_PAGES default "9" if PPC32 && PPC_16K_PAGES range 7 64 if PPC32 && PPC_64K_PAGES default "7" if PPC32 && PPC_64K_PAGES range 5 64 if PPC32 && PPC_256K_PAGES default "5" if PPC32 && PPC_256K_PAGES range 11 64 default "11" help The kernel memory allocator divides physically contiguous memory blocks into "zones", where each zone is a power of two number of pages. This option selects the largest power of two that the kernel keeps in the memory allocator. If you need to allocate very large blocks of physically contiguous memory, then you may need to increase this value. This config option is actually maximum order plus one. For example, a value of 11 means that the largest free memory block is 2^10 pages. The page size is not necessarily 4KB. For example, on 64-bit systems, 64KB pages can be enabled via CONFIG_PPC_64K_PAGES. Keep this in mind when choosing a value for this option. config PPC_SUBPAGE_PROT bool "Support setting protections for 4k subpages" depends on PPC_STD_MMU_64 && PPC_64K_PAGES help This option adds support for a system call to allow user programs to set access permissions (read/write, readonly, or no access) on the 4k subpages of each 64k page. config SCHED_SMT bool "SMT (Hyperthreading) scheduler support" depends on PPC64 && SMP help SMT scheduler support improves the CPU scheduler's decision making when dealing with POWER5 cpus at a cost of slightly increased overhead in some places. If unsure say N here. config PPC_DENORMALISATION bool "PowerPC denormalisation exception handling" depends on PPC_BOOK3S_64 default "y" if PPC_POWERNV ---help--- Add support for handling denormalisation of single precision values. Useful for bare metal only. If unsure say Y here. config CMDLINE_BOOL bool "Default bootloader kernel arguments" config CMDLINE string "Initial kernel command string" depends on CMDLINE_BOOL default "console=ttyS0,9600 console=tty0 root=/dev/sda2" help On some platforms, there is currently no way for the boot loader to pass arguments to the kernel. For these platforms, you can supply some command-line options at build time by entering them here. In most cases you will need to specify the root device here. config CMDLINE_FORCE bool "Always use the default kernel command string" depends on CMDLINE_BOOL help Always use the default kernel command string, even if the boot loader passes other arguments to the kernel. This is useful if you cannot or don't want to change the command-line options your boot loader passes to the kernel. config EXTRA_TARGETS string "Additional default image types" help List additional targets to be built by the bootwrapper here (separated by spaces). This is useful for targets that depend of device tree files in the .dts directory. Targets in this list will be build as part of the default build target, or when the user does a 'make zImage' or a 'make zImage.initrd'. If unsure, leave blank config ARCH_WANTS_FREEZER_CONTROL def_bool y depends on ADB_PMU source kernel/power/Kconfig config SECCOMP bool "Enable seccomp to safely compute untrusted bytecode" depends on PROC_FS default y help This kernel feature is useful for number crunching applications that may need to compute untrusted bytecode during their execution. By using pipes or other transports made available to the process as file descriptors supporting the read/write syscalls, it's possible to isolate those applications in their own address space using seccomp. Once seccomp is enabled via /proc//seccomp, it cannot be disabled and the task is only allowed to execute a few safe syscalls defined by each seccomp mode. If unsure, say Y. Only embedded should say N here. endmenu config ISA_DMA_API bool default PCI menu "Bus options" config ISA bool "Support for ISA-bus hardware" depends on PPC_CHRP select PPC_I8259 help Find out whether you have ISA slots on your motherboard. ISA is the name of a bus system, i.e. the way the CPU talks to the other stuff inside your box. If you have an Apple machine, say N here; if you have an IBM RS/6000 or pSeries machine, say Y. If you have an embedded board, consult your board documentation. config ZONE_DMA bool default y config NEED_DMA_MAP_STATE def_bool (PPC64 || NOT_COHERENT_CACHE) config NEED_SG_DMA_LENGTH def_bool y config GENERIC_ISA_DMA bool depends on ISA_DMA_API default y config PPC_INDIRECT_PCI bool depends on PCI default y if 40x || 44x default n config EISA bool config SBUS bool config FSL_SOC bool config FSL_PCI bool select PPC_INDIRECT_PCI select PCI_QUIRKS config FSL_PMC bool default y depends on SUSPEND && (PPC_85xx || PPC_86xx) help Freescale MPC85xx/MPC86xx power management controller support (suspend/resume). For MPC83xx see platforms/83xx/suspend.c config PPC4xx_CPM bool default y depends on SUSPEND && (44x || 40x) help PPC4xx Clock Power Management (CPM) support (suspend/resume). It also enables support for two different idle states (idle-wait and idle-doze). config 4xx_SOC bool config FSL_LBC bool "Freescale Local Bus support" depends on FSL_SOC help Enables reporting of errors from the Freescale local bus controller. Also contains some common code used by drivers for specific local bus peripherals. config FSL_GTM bool depends on PPC_83xx || QUICC_ENGINE || CPM2 help Freescale General-purpose Timers support # Yes MCA RS/6000s exist but Linux-PPC does not currently support any config MCA bool # Platforms that what PCI turned unconditionally just do select PCI # in their config node. Platforms that want to choose at config # time should select PPC_PCI_CHOICE config PPC_PCI_CHOICE bool config PCI bool "PCI support" if PPC_PCI_CHOICE default y if !40x && !CPM2 && !8xx && !PPC_83xx \ && !PPC_85xx && !PPC_86xx && !GAMECUBE_COMMON default PCI_QSPAN if !4xx && !CPM2 && 8xx select GENERIC_PCI_IOMAP help Find out whether your system includes a PCI bus. PCI is the name of a bus system, i.e. the way the CPU talks to the other stuff inside your box. If you say Y here, the kernel will include drivers and infrastructure code to support PCI bus devices. config PCI_DOMAINS def_bool PCI config PCI_SYSCALL def_bool PCI config PCI_QSPAN bool "QSpan PCI" depends on !4xx && !CPM2 && 8xx select PPC_I8259 help Say Y here if you have a system based on a Motorola 8xx-series embedded processor with a QSPAN PCI interface, otherwise say N. config PCI_8260 bool depends on PCI && 8260 select PPC_INDIRECT_PCI default y source "drivers/pci/pcie/Kconfig" source "drivers/pci/Kconfig" source "drivers/pcmcia/Kconfig" source "drivers/pci/hotplug/Kconfig" config HAS_RAPIDIO bool default n config RAPIDIO tristate "RapidIO support" depends on HAS_RAPIDIO || PCI help If you say Y here, the kernel will include drivers and infrastructure code to support RapidIO interconnect devices. config FSL_RIO bool "Freescale Embedded SRIO Controller support" depends on RAPIDIO = y && HAS_RAPIDIO default "n" ---help--- Include support for RapidIO controller on Freescale embedded processors (MPC8548, MPC8641, etc). source "drivers/rapidio/Kconfig" endmenu config NONSTATIC_KERNEL bool default n menu "Advanced setup" depends on PPC32 config ADVANCED_OPTIONS bool "Prompt for advanced kernel configuration options" help This option will enable prompting for a variety of advanced kernel configuration options. These options can cause the kernel to not work if they are set incorrectly, but can be used to optimize certain aspects of kernel memory management. Unless you know what you are doing, say N here. comment "Default settings for advanced configuration options are used" depends on !ADVANCED_OPTIONS config LOWMEM_SIZE_BOOL bool "Set maximum low memory" depends on ADVANCED_OPTIONS help This option allows you to set the maximum amount of memory which will be used as "low memory", that is, memory which the kernel can access directly, without having to set up a kernel virtual mapping. This can be useful in optimizing the layout of kernel virtual memory. Say N here unless you know what you are doing. config LOWMEM_SIZE hex "Maximum low memory size (in bytes)" if LOWMEM_SIZE_BOOL default "0x30000000" config LOWMEM_CAM_NUM_BOOL bool "Set number of CAMs to use to map low memory" depends on ADVANCED_OPTIONS && FSL_BOOKE help This option allows you to set the maximum number of CAM slots that will be used to map low memory. There are a limited number of slots available and even more limited number that will fit in the L1 MMU. However, using more entries will allow mapping more low memory. This can be useful in optimizing the layout of kernel virtual memory. Say N here unless you know what you are doing. config LOWMEM_CAM_NUM depends on FSL_BOOKE int "Number of CAMs to use to map low memory" if LOWMEM_CAM_NUM_BOOL default 3 config DYNAMIC_MEMSTART bool "Enable page aligned dynamic load address for kernel" depends on ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || 44x) select NONSTATIC_KERNEL help This option enables the kernel to be loaded at any page aligned physical address. The kernel creates a mapping from KERNELBASE to the address where the kernel is loaded. The page size here implies the TLB page size of the mapping for kernel on the particular platform. Please refer to the init code for finding the TLB page size. DYNAMIC_MEMSTART is an easy way of implementing pseudo-RELOCATABLE kernel image, where the only restriction is the page aligned kernel load address. When this option is enabled, the compile time physical address CONFIG_PHYSICAL_START is ignored. This option is overridden by CONFIG_RELOCATABLE config RELOCATABLE bool "Build a relocatable kernel" depends on ADVANCED_OPTIONS && FLATMEM && (44x || FSL_BOOKE) select NONSTATIC_KERNEL help This builds a kernel image that is capable of running at the location the kernel is loaded at, without any alignment restrictions. This feature is a superset of DYNAMIC_MEMSTART and hence overrides it. One use is for the kexec on panic case where the recovery kernel must live at a different physical address than the primary kernel. Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address it has been loaded at and the compile time physical addresses CONFIG_PHYSICAL_START is ignored. However CONFIG_PHYSICAL_START setting can still be useful to bootwrappers that need to know the load address of the kernel (eg. u-boot/mkimage). config RELOCATABLE_PPC32 def_bool y depends on PPC32 && RELOCATABLE config PAGE_OFFSET_BOOL bool "Set custom page offset address" depends on ADVANCED_OPTIONS help This option allows you to set the kernel virtual address at which the kernel will map low memory. This can be useful in optimizing the virtual memory layout of the system. Say N here unless you know what you are doing. config PAGE_OFFSET hex "Virtual address of memory base" if PAGE_OFFSET_BOOL default "0xc0000000" config KERNEL_START_BOOL bool "Set custom kernel base address" depends on ADVANCED_OPTIONS help This option allows you to set the kernel virtual address at which the kernel will be loaded. Normally this should match PAGE_OFFSET however there are times (like kdump) that one might not want them to be the same. Say N here unless you know what you are doing. config KERNEL_START hex "Virtual address of kernel base" if KERNEL_START_BOOL default PAGE_OFFSET if PAGE_OFFSET_BOOL default "0xc2000000" if CRASH_DUMP && !NONSTATIC_KERNEL default "0xc0000000" config PHYSICAL_START_BOOL bool "Set physical address where the kernel is loaded" depends on ADVANCED_OPTIONS && FLATMEM && FSL_BOOKE help This gives the physical address where the kernel is loaded. Say N here unless you know what you are doing. config PHYSICAL_START hex "Physical address where the kernel is loaded" if PHYSICAL_START_BOOL default "0x02000000" if PPC_STD_MMU && CRASH_DUMP && !NONSTATIC_KERNEL default "0x00000000" config PHYSICAL_ALIGN hex default "0x04000000" if FSL_BOOKE help This value puts the alignment restrictions on physical address where kernel is loaded and run from. Kernel is compiled for an address which meets above alignment restriction. config TASK_SIZE_BOOL bool "Set custom user task size" depends on ADVANCED_OPTIONS help This option allows you to set the amount of virtual address space allocated to user tasks. This can be useful in optimizing the virtual memory layout of the system. Say N here unless you know what you are doing. config TASK_SIZE hex "Size of user task space" if TASK_SIZE_BOOL default "0x80000000" if PPC_8xx default "0xc0000000" config CONSISTENT_SIZE_BOOL bool "Set custom consistent memory pool size" depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE help This option allows you to set the size of the consistent memory pool. This pool of virtual memory is used to make consistent memory allocations. config CONSISTENT_SIZE hex "Size of consistent memory pool" if CONSISTENT_SIZE_BOOL default "0x00200000" if NOT_COHERENT_CACHE config PIN_TLB bool "Pinned Kernel TLBs (860 ONLY)" depends on ADVANCED_OPTIONS && 8xx endmenu if PPC64 config RELOCATABLE bool "Build a relocatable kernel" depends on !COMPILE_TEST select NONSTATIC_KERNEL help This builds a kernel image that is capable of running anywhere in the RMA (real memory area) at any 16k-aligned base address. The kernel is linked as a position-independent executable (PIE) and contains dynamic relocations which are processed early in the bootup process. One use is for the kexec on panic case where the recovery kernel must live at a different physical address than the primary kernel. # This value must have zeroes in the bottom 60 bits otherwise lots will break config PAGE_OFFSET hex default "0xc000000000000000" config KERNEL_START hex default "0xc000000000000000" config PHYSICAL_START hex default "0x00000000" endif config ARCH_RANDOM def_bool n source "net/Kconfig" source "drivers/Kconfig" source "fs/Kconfig" source "arch/powerpc/sysdev/qe_lib/Kconfig" source "lib/Kconfig" source "arch/powerpc/Kconfig.debug" source "security/Kconfig" config KEYS_COMPAT bool depends on COMPAT && KEYS default y source "crypto/Kconfig" config PPC_LIB_RHEAP bool source "arch/powerpc/kvm/Kconfig"