/*
 * A collection of structures, addresses, and values associated with
 * the RPCG RPX-Lite board.  Copied from the MBX stuff.
 *
 * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
 */
#ifdef __KERNEL__
#ifndef __MACH_RPX_DEFS
#define __MACH_RPX_DEFS


#ifndef __ASSEMBLY__
/* A Board Information structure that is given to a program when
 * prom starts it up.
 */
typedef struct bd_info {
	unsigned int	bi_memstart;	/* Memory start address */
	unsigned int	bi_memsize;	/* Memory (end) size in bytes */
	unsigned int	bi_intfreq;	/* Internal Freq, in Hz */
	unsigned int	bi_busfreq;	/* Bus Freq, in Hz */
	unsigned char	bi_enetaddr[6];
	unsigned int	bi_baudrate;
} bd_t;

extern bd_t m8xx_board_info;

/* Memory map is configured by the PROM startup.
 * We just map a few things we need.  The CSR is actually 4 byte-wide
 * registers that can be accessed as 8-, 16-, or 32-bit values.
 */
#define RPX_CSR_ADDR		((uint)0xfa400000)
#define RPX_CSR_SIZE		((uint)(4 * 1024))
#define IMAP_ADDR		((uint)0xfa200000)
#define IMAP_SIZE		((uint)(64 * 1024))
#define PCMCIA_MEM_ADDR		((uint)0x04000000)
#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
#define PCMCIA_IO_ADDR		((uint)0x04400000)
#define PCMCIA_IO_SIZE		((uint)(4 * 1024))

/* Things of interest in the CSR.
*/
#define BCSR0_ETHEN		((uint)0x80000000)
#define BCSR0_ETHLPBK		((uint)0x40000000)
#define BCSR0_COLTESTDIS	((uint)0x20000000)
#define BCSR0_FULLDPLXDIS	((uint)0x10000000)
#define BCSR0_LEDOFF		((uint)0x08000000)
#define BCSR0_USBDISABLE	((uint)0x04000000)
#define BCSR0_USBHISPEED	((uint)0x02000000)
#define BCSR0_USBPWREN		((uint)0x01000000)
#define BCSR0_PCMCIAVOLT	((uint)0x000f0000)
#define BCSR0_PCMCIA3VOLT	((uint)0x000a0000)
#define BCSR0_PCMCIA5VOLT	((uint)0x00060000)

#define BCSR1_IPB5SEL          ((uint)0x00100000)
#define BCSR1_PCVCTL4          ((uint)0x00080000)
#define BCSR1_PCVCTL5          ((uint)0x00040000)
#define BCSR1_PCVCTL6          ((uint)0x00020000)
#define BCSR1_PCVCTL7          ((uint)0x00010000)

/* define IO_BASE for pcmcia */
#define _IO_BASE 0x80000000
#define _IO_BASE_SIZE 0x1000

#ifdef CONFIG_IDE
# define MAX_HWIFS 1
#endif

/* CPM Ethernet through SCCx.
 *
 * This ENET stuff is for the MPC850 with ethernet on SCC2.  Some of
 * this may be unique to the RPX-Lite configuration.
 * Note TENA is on Port B.
 */
#define PA_ENET_RXD	((ushort)0x0004)
#define PA_ENET_TXD	((ushort)0x0008)
#define PA_ENET_TCLK	((ushort)0x0200)
#define PA_ENET_RCLK	((ushort)0x0800)
#define PB_ENET_TENA	((uint)0x00002000)
#define PC_ENET_CLSN	((ushort)0x0040)
#define PC_ENET_RENA	((ushort)0x0080)

#define SICR_ENET_MASK	((uint)0x0000ff00)
#define SICR_ENET_CLKRT	((uint)0x00003d00)

/* We don't use the 8259.
*/
#define NR_8259_INTS	0

#endif /* !__ASSEMBLY__ */
#endif /* __MACH_RPX_DEFS */
#endif /* __KERNEL__ */