/* * Low-Level PCI Support for the SH7751 * * Dustin McIntire (dustin@sensoria.com) * Derived from arch/i386/kernel/pci-*.c which bore the message: * (c) 1999--2000 Martin Mares * * Ported to the new API by Paul Mundt * With cleanup by Paul van Gool * * May be copied or modified under the terms of the GNU General Public * License. See linux/COPYING for more information. * */ #undef DEBUG #include #include #include #include #include #include "pci-sh4.h" #include #include /* * Initialization. Try all known PCI access methods. Note that we support * using both PCI BIOS and direct access: in such cases, we use I/O ports * to access config space. * * Note that the platform specific initialization (BSC registers, and memory * space mapping) will be called via the platform defined function * pcibios_init_platform(). */ static int __init sh7751_pci_init(void) { unsigned int id; int ret; pr_debug("PCI: Starting intialization.\n"); /* check for SH7751/SH7751R hardware */ id = pci_read_reg(SH7751_PCICONF0); if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) && id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) { pr_debug("PCI: This is not an SH7751(R) (%x)\n", id); return -ENODEV; } if ((ret = sh4_pci_check_direct()) != 0) return ret; return pcibios_init_platform(); } subsys_initcall(sh7751_pci_init); static int __init __area_sdram_check(unsigned int area) { u32 word; word = inl(SH7751_BCR1); /* check BCR for SDRAM in area */ if (((word >> area) & 1) == 0) { printk("PCI: Area %d is not configured for SDRAM. BCR1=0x%x\n", area, word); return 0; } pci_write_reg(word, SH4_PCIBCR1); word = (u16)inw(SH7751_BCR2); /* check BCR2 for 32bit SDRAM interface*/ if (((word >> (area << 1)) & 0x3) != 0x3) { printk("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%x\n", area, word); return 0; } pci_write_reg(word, SH4_PCIBCR2); return 1; } int __init sh7751_pcic_init(struct sh4_pci_address_map *map) { u32 reg; u32 word; /* Set the BCR's to enable PCI access */ reg = inl(SH7751_BCR1); reg |= 0x80000; outl(reg, SH7751_BCR1); /* Turn the clocks back on (not done in reset)*/ pci_write_reg(0, SH4_PCICLKR); /* Clear Powerdown IRQ's (not done in reset) */ word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0; pci_write_reg(word, SH4_PCIPINT); /* * This code is unused for some boards as it is done in the * bootloader and doing it here means the MAC addresses loaded * by the bootloader get lost. */ if (!(map->flags & SH4_PCIC_NO_RESET)) { /* toggle PCI reset pin */ word = SH4_PCICR_PREFIX | SH4_PCICR_PRST; pci_write_reg(word, SH4_PCICR); /* Wait for a long time... not 1 sec. but long enough */ mdelay(100); word = SH4_PCICR_PREFIX; pci_write_reg(word, SH4_PCICR); } /* set the command/status bits to: * Wait Cycle Control + Parity Enable + Bus Master + * Mem space enable */ word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER | SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES; pci_write_reg(word, SH7751_PCICONF1); /* define this host as the host bridge */ word = PCI_BASE_CLASS_BRIDGE << 24; pci_write_reg(word, SH7751_PCICONF2); /* Set IO and Mem windows to local address * Make PCI and local address the same for easy 1 to 1 mapping * Window0 = map->window0.size @ non-cached area base = SDRAM * Window1 = map->window1.size @ cached area base = SDRAM */ word = map->window0.size - 1; pci_write_reg(word, SH4_PCILSR0); word = map->window1.size - 1; pci_write_reg(word, SH4_PCILSR1); /* Set the values on window 0 PCI config registers */ word = P2SEGADDR(map->window0.base); pci_write_reg(word, SH4_PCILAR0); pci_write_reg(word, SH7751_PCICONF5); /* Set the values on window 1 PCI config registers */ word = PHYSADDR(map->window1.base); pci_write_reg(word, SH4_PCILAR1); pci_write_reg(word, SH7751_PCICONF6); /* Set the local 16MB PCI memory space window to * the lowest PCI mapped address */ word = PCIBIOS_MIN_MEM & SH4_PCIMBR_MASK; pr_debug("PCI: Setting upper bits of Memory window to 0x%x\n", word); pci_write_reg(word , SH4_PCIMBR); /* Map IO space into PCI IO window * The IO window is 64K-PCIBIOS_MIN_IO in size * IO addresses will be translated to the * PCI IO window base address */ pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n", PCIBIOS_MIN_IO, (64 << 10), SH7751_PCI_IO_BASE + PCIBIOS_MIN_IO); /* Make sure the MSB's of IO window are set to access PCI space * correctly */ word = PCIBIOS_MIN_IO & SH4_PCIIOBR_MASK; pr_debug("PCI: Setting upper bits of IO window to 0x%x\n", word); pci_write_reg(word, SH4_PCIIOBR); /* Set PCI WCRx, BCRx's, copy from BSC locations */ /* check BCR for SDRAM in specified area */ switch (map->window0.base) { case SH7751_CS0_BASE_ADDR: word = __area_sdram_check(0); break; case SH7751_CS1_BASE_ADDR: word = __area_sdram_check(1); break; case SH7751_CS2_BASE_ADDR: word = __area_sdram_check(2); break; case SH7751_CS3_BASE_ADDR: word = __area_sdram_check(3); break; case SH7751_CS4_BASE_ADDR: word = __area_sdram_check(4); break; case SH7751_CS5_BASE_ADDR: word = __area_sdram_check(5); break; case SH7751_CS6_BASE_ADDR: word = __area_sdram_check(6); break; } if (!word) return 0; /* configure the wait control registers */ word = inl(SH7751_WCR1); pci_write_reg(word, SH4_PCIWCR1); word = inl(SH7751_WCR2); pci_write_reg(word, SH4_PCIWCR2); word = inl(SH7751_WCR3); pci_write_reg(word, SH4_PCIWCR3); word = inl(SH7751_MCR); pci_write_reg(word, SH4_PCIMCR); /* NOTE: I'm ignoring the PCI error IRQs for now.. * TODO: add support for the internal error interrupts and * DMA interrupts... */ pci_fixup_pcic(); /* SH7751 init done, set central function init complete */ /* use round robin mode to stop a device starving/overruning */ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM; pci_write_reg(word, SH4_PCICR); return 1; }