/* * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. * * This software is available to you under a choice of one of two * licenses. You may choose to be licensed under the terms of the GNU * General Public License (GPL) Version 2, available from the file * COPYING in the main directory of this source tree, or the * OpenIB.org BSD license below: * * Redistribution and use in source and binary forms, with or * without modification, are permitted provided that the following * conditions are met: * * - Redistributions of source code must retain the above * copyright notice, this list of conditions and the following * disclaimer. * * - Redistributions in binary form must reproduce the above * copyright notice, this list of conditions and the following * disclaimer in the documentation and/or other materials * provided with the distribution. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE * SOFTWARE. */ #include #include #include #include "ipath_kernel.h" /* * InfiniPath I2C driver for a serial eeprom. This is not a generic * I2C interface. For a start, the device we're using (Atmel AT24C11) * doesn't work like a regular I2C device. It looks like one * electrically, but not logically. Normal I2C devices have a single * 7-bit or 10-bit I2C address that they respond to. Valid 7-bit * addresses range from 0x03 to 0x77. Addresses 0x00 to 0x02 and 0x78 * to 0x7F are special reserved addresses (e.g. 0x00 is the "general * call" address.) The Atmel device, on the other hand, responds to ALL * 7-bit addresses. It's designed to be the only device on a given I2C * bus. A 7-bit address corresponds to the memory address within the * Atmel device itself. * * Also, the timing requirements mean more than simple software * bitbanging, with readbacks from chip to ensure timing (simple udelay * is not enough). * * This all means that accessing the device is specialized enough * that using the standard kernel I2C bitbanging interface would be * impossible. For example, the core I2C eeprom driver expects to find * a device at one or more of a limited set of addresses only. It doesn't * allow writing to an eeprom. It also doesn't provide any means of * accessing eeprom contents from within the kernel, only via sysfs. */ /* Added functionality for IBA7220-based cards */ #define IPATH_EEPROM_DEV_V1 0xA0 #define IPATH_EEPROM_DEV_V2 0xA2 #define IPATH_TEMP_DEV 0x98 #define IPATH_BAD_DEV (IPATH_EEPROM_DEV_V2+2) #define IPATH_NO_DEV (0xFF) /* * The number of I2C chains is proliferating. Table below brings * some order to the madness. The basic principle is that the * table is scanned from the top, and a "probe" is made to the * device probe_dev. If that succeeds, the chain is considered * to be of that type, and dd->i2c_chain_type is set to the index+1 * of the entry. * The +1 is so static initialization can mean "unknown, do probe." */ static struct i2c_chain_desc { u8 probe_dev; /* If seen at probe, chain is this type */ u8 eeprom_dev; /* Dev addr (if any) for EEPROM */ u8 temp_dev; /* Dev Addr (if any) for Temp-sense */ } i2c_chains[] = { { IPATH_BAD_DEV, IPATH_NO_DEV, IPATH_NO_DEV }, /* pre-iba7220 bds */ { IPATH_EEPROM_DEV_V1, IPATH_EEPROM_DEV_V1, IPATH_TEMP_DEV}, /* V1 */ { IPATH_EEPROM_DEV_V2, IPATH_EEPROM_DEV_V2, IPATH_TEMP_DEV}, /* V2 */ { IPATH_NO_DEV } }; enum i2c_type { i2c_line_scl = 0, i2c_line_sda }; enum i2c_state { i2c_line_low = 0, i2c_line_high }; #define READ_CMD 1 #define WRITE_CMD 0 /** * i2c_gpio_set - set a GPIO line * @dd: the infinipath device * @line: the line to set * @new_line_state: the state to set * * Returns 0 if the line was set to the new state successfully, non-zero * on error. */ static int i2c_gpio_set(struct ipath_devdata *dd, enum i2c_type line, enum i2c_state new_line_state) { u64 out_mask, dir_mask, *gpioval; unsigned long flags = 0; gpioval = &dd->ipath_gpio_out; if (line == i2c_line_scl) { dir_mask = dd->ipath_gpio_scl; out_mask = (1UL << dd->ipath_gpio_scl_num); } else { dir_mask = dd->ipath_gpio_sda; out_mask = (1UL << dd->ipath_gpio_sda_num); } spin_lock_irqsave(&dd->ipath_gpio_lock, flags); if (new_line_state == i2c_line_high) { /* tri-state the output rather than force high */ dd->ipath_extctrl &= ~dir_mask; } else { /* config line to be an output */ dd->ipath_extctrl |= dir_mask; } ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl); /* set output as well (no real verify) */ if (new_line_state == i2c_line_high) *gpioval |= out_mask; else *gpioval &= ~out_mask; ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_out, *gpioval); spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); return 0; } /** * i2c_gpio_get - get a GPIO line state * @dd: the infinipath device * @line: the line to get * @curr_statep: where to put the line state * * Returns 0 if the line was set to the new state successfully, non-zero * on error. curr_state is not set on error. */ static int i2c_gpio_get(struct ipath_devdata *dd, enum i2c_type line, enum i2c_state *curr_statep) { u64 read_val, mask; int ret; unsigned long flags = 0; /* check args */ if (curr_statep == NULL) { ret = 1; goto bail; } /* config line to be an input */ if (line == i2c_line_scl) mask = dd->ipath_gpio_scl; else mask = dd->ipath_gpio_sda; spin_lock_irqsave(&dd->ipath_gpio_lock, flags); dd->ipath_extctrl &= ~mask; ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, dd->ipath_extctrl); /* * Below is very unlikely to reflect true input state if Output * Enable actually changed. */ read_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus); spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); if (read_val & mask) *curr_statep = i2c_line_high; else *curr_statep = i2c_line_low; ret = 0; bail: return ret; } /** * i2c_wait_for_writes - wait for a write * @dd: the infinipath device * * We use this instead of udelay directly, so we can make sure * that previous register writes have been flushed all the way * to the chip. Since we are delaying anyway, the cost doesn't * hurt, and makes the bit twiddling more regular */ static void i2c_wait_for_writes(struct ipath_devdata *dd) { (void)ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); rmb(); } static void scl_out(struct ipath_devdata *dd, u8 bit) { udelay(1); i2c_gpio_set(dd, i2c_line_scl, bit ? i2c_line_high : i2c_line_low); i2c_wait_for_writes(dd); } static void sda_out(struct ipath_devdata *dd, u8 bit) { i2c_gpio_set(dd, i2c_line_sda, bit ? i2c_line_high : i2c_line_low); i2c_wait_for_writes(dd); } static u8 sda_in(struct ipath_devdata *dd, int wait) { enum i2c_state bit; if (i2c_gpio_get(dd, i2c_line_sda, &bit)) ipath_dbg("get bit failed!\n"); if (wait) i2c_wait_for_writes(dd); return bit == i2c_line_high ? 1U : 0; } /** * i2c_ackrcv - see if ack following write is true * @dd: the infinipath device */ static int i2c_ackrcv(struct ipath_devdata *dd) { u8 ack_received; /* AT ENTRY SCL = LOW */ /* change direction, ignore data */ ack_received = sda_in(dd, 1); scl_out(dd, i2c_line_high); ack_received = sda_in(dd, 1) == 0; scl_out(dd, i2c_line_low); return ack_received; } /** * rd_byte - read a byte, leaving ACK, STOP, etc up to caller * @dd: the infinipath device * * Returns byte shifted out of device */ static int rd_byte(struct ipath_devdata *dd) { int bit_cntr, data; data = 0; for (bit_cntr = 7; bit_cntr >= 0; --bit_cntr) { data <<= 1; scl_out(dd, i2c_line_high); data |= sda_in(dd, 0); scl_out(dd, i2c_line_low); } return data; } /** * wr_byte - write a byte, one bit at a time * @dd: the infinipath device * @data: the byte to write * * Returns 0 if we got the following ack, otherwise 1 */ static int wr_byte(struct ipath_devdata *dd, u8 data) { int bit_cntr; u8 bit; for (bit_cntr = 7; bit_cntr >= 0; bit_cntr--) { bit = (data >> bit_cntr) & 1; sda_out(dd, bit); scl_out(dd, i2c_line_high); scl_out(dd, i2c_line_low); } return (!i2c_ackrcv(dd)) ? 1 : 0; } static void send_ack(struct ipath_devdata *dd) { sda_out(dd, i2c_line_low); scl_out(dd, i2c_line_high); scl_out(dd, i2c_line_low); sda_out(dd, i2c_line_high); } /** * i2c_startcmd - transmit the start condition, followed by address/cmd * @dd: the infinipath device * @offset_dir: direction byte * * (both clock/data high, clock high, data low while clock is high) */ static int i2c_startcmd(struct ipath_devdata *dd, u8 offset_dir) { int res; /* issue start sequence */ sda_out(dd, i2c_line_high); scl_out(dd, i2c_line_high); sda_out(dd, i2c_line_low); scl_out(dd, i2c_line_low); /* issue length and direction byte */ res = wr_byte(dd, offset_dir); if (res) ipath_cdbg(VERBOSE, "No ack to complete start\n"); return res; } /** * stop_cmd - transmit the stop condition * @dd: the infinipath device * * (both clock/data low, clock high, data high while clock is high) */ static void stop_cmd(struct ipath_devdata *dd) { scl_out(dd, i2c_line_low); sda_out(dd, i2c_line_low); scl_out(dd, i2c_line_high); sda_out(dd, i2c_line_high); udelay(2); } /** * eeprom_reset - reset I2C communication * @dd: the infinipath device */ static int eeprom_reset(struct ipath_devdata *dd) { int clock_cycles_left = 9; u64 *gpioval = &dd->ipath_gpio_out; int ret; unsigned long flags; spin_lock_irqsave(&dd->ipath_gpio_lock, flags); /* Make sure shadows are consistent */ dd->ipath_extctrl = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extctrl); *gpioval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_gpio_out); spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); ipath_cdbg(VERBOSE, "Resetting i2c eeprom; initial gpioout reg " "is %llx\n", (unsigned long long) *gpioval); /* * This is to get the i2c into a known state, by first going low, * then tristate sda (and then tristate scl as first thing * in loop) */ scl_out(dd, i2c_line_low); sda_out(dd, i2c_line_high); /* Clock up to 9 cycles looking for SDA hi, then issue START and STOP */ while (clock_cycles_left--) { scl_out(dd, i2c_line_high); /* SDA seen high, issue START by dropping it while SCL high */ if (sda_in(dd, 0)) { sda_out(dd, i2c_line_low); scl_out(dd, i2c_line_low); /* ATMEL spec says must be followed by STOP. */ scl_out(dd, i2c_line_high); sda_out(dd, i2c_line_high); ret = 0; goto bail; } scl_out(dd, i2c_line_low); } ret = 1; bail: return ret; } /* * Probe for I2C device at specified address. Returns 0 for "success" * to match rest of this file. * Leave bus in "reasonable" state for further commands. */ static int i2c_probe(struct ipath_devdata *dd, int devaddr) { int ret = 0; ret = eeprom_reset(dd); if (ret) { ipath_dev_err(dd, "Failed reset probing device 0x%02X\n", devaddr); return ret; } /* * Reset no longer leaves bus in start condition, so normal * i2c_startcmd() will do. */ ret = i2c_startcmd(dd, devaddr | READ_CMD); if (ret) ipath_cdbg(VERBOSE, "Failed startcmd for device 0x%02X\n", devaddr); else { /* * Device did respond. Complete a single-byte read, because some * devices apparently cannot handle STOP immediately after they * ACK the start-cmd. */ int data; data = rd_byte(dd); stop_cmd(dd); ipath_cdbg(VERBOSE, "Response from device 0x%02X\n", devaddr); } return ret; } /* * Returns the "i2c type". This is a pointer to a struct that describes * the I2C chain on this board. To minimize impact on struct ipath_devdata, * the (small integer) index into the table is actually memoized, rather * then the pointer. * Memoization is because the type is determined on the first call per chip. * An alternative would be to move type determination to early * init code. */ static struct i2c_chain_desc *ipath_i2c_type(struct ipath_devdata *dd) { int idx; /* Get memoized index, from previous successful probes */ idx = dd->ipath_i2c_chain_type - 1; if (idx >= 0 && idx < (ARRAY_SIZE(i2c_chains) - 1)) goto done; idx = 0; while (i2c_chains[idx].probe_dev != IPATH_NO_DEV) { /* if probe succeeds, this is type */ if (!i2c_probe(dd, i2c_chains[idx].probe_dev)) break; ++idx; } /* * Old EEPROM (first entry) may require a reset after probe, * rather than being able to "start" after "stop" */ if (idx == 0) eeprom_reset(dd); if (i2c_chains[idx].probe_dev == IPATH_NO_DEV) idx = -1; else dd->ipath_i2c_chain_type = idx + 1; done: return (idx >= 0) ? i2c_chains + idx : NULL; } static int ipath_eeprom_internal_read(struct ipath_devdata *dd, u8 eeprom_offset, void *buffer, int len) { int ret; struct i2c_chain_desc *icd; u8 *bp = buffer; ret = 1; icd = ipath_i2c_type(dd); if (!icd) goto bail; if (icd->eeprom_dev == IPATH_NO_DEV) { /* legacy not-really-I2C */ ipath_cdbg(VERBOSE, "Start command only address\n"); eeprom_offset = (eeprom_offset << 1) | READ_CMD; ret = i2c_startcmd(dd, eeprom_offset); } else { /* Actual I2C */ ipath_cdbg(VERBOSE, "Start command uses devaddr\n"); if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) { ipath_dbg("Failed EEPROM startcmd\n"); stop_cmd(dd); ret = 1; goto bail; } ret = wr_byte(dd, eeprom_offset); stop_cmd(dd); if (ret) { ipath_dev_err(dd, "Failed to write EEPROM address\n"); ret = 1; goto bail; } ret = i2c_startcmd(dd, icd->eeprom_dev | READ_CMD); } if (ret) { ipath_dbg("Failed startcmd for dev %02X\n", icd->eeprom_dev); stop_cmd(dd); ret = 1; goto bail; } /* * eeprom keeps clocking data out as long as we ack, automatically * incrementing the address. */ while (len-- > 0) { /* get and store data */ *bp++ = rd_byte(dd); /* send ack if not the last byte */ if (len) send_ack(dd); } stop_cmd(dd); ret = 0; bail: return ret; } static int ipath_eeprom_internal_write(struct ipath_devdata *dd, u8 eeprom_offset, const void *buffer, int len) { int sub_len; const u8 *bp = buffer; int max_wait_time, i; int ret; struct i2c_chain_desc *icd; ret = 1; icd = ipath_i2c_type(dd); if (!icd) goto bail; while (len > 0) { if (icd->eeprom_dev == IPATH_NO_DEV) { if (i2c_startcmd(dd, (eeprom_offset << 1) | WRITE_CMD)) { ipath_dbg("Failed to start cmd offset %u\n", eeprom_offset); goto failed_write; } } else { /* Real I2C */ if (i2c_startcmd(dd, icd->eeprom_dev | WRITE_CMD)) { ipath_dbg("Failed EEPROM startcmd\n"); goto failed_write; } ret = wr_byte(dd, eeprom_offset); if (ret) { ipath_dev_err(dd, "Failed to write EEPROM " "address\n"); goto failed_write; } } sub_len = min(len, 4); eeprom_offset += sub_len; len -= sub_len; for (i = 0; i < sub_len; i++) { if (wr_byte(dd, *bp++)) { ipath_dbg("no ack after byte %u/%u (%u " "total remain)\n", i, sub_len, len + sub_len - i); goto failed_write; } } stop_cmd(dd); /* * wait for write complete by waiting for a successful * read (the chip replies with a zero after the write * cmd completes, and before it writes to the eeprom. * The startcmd for the read will fail the ack until * the writes have completed. We do this inline to avoid * the debug prints that are in the real read routine * if the startcmd fails. * We also use the proper device address, so it doesn't matter * whether we have real eeprom_dev. legacy likes any address. */ max_wait_time = 100; while (i2c_startcmd(dd, icd->eeprom_dev | READ_CMD)) { stop_cmd(dd); if (!--max_wait_time) { ipath_dbg("Did not get successful read to " "complete write\n"); goto failed_write; } } /* now read (and ignore) the resulting byte */ rd_byte(dd); stop_cmd(dd); } ret = 0; goto bail; failed_write: stop_cmd(dd); ret = 1; bail: return ret; } /** * ipath_eeprom_read - receives bytes from the eeprom via I2C * @dd: the infinipath device * @eeprom_offset: address to read from * @buffer: where to store result * @len: number of bytes to receive */ int ipath_eeprom_read(struct ipath_devdata *dd, u8 eeprom_offset, void *buff, int len) { int ret; ret = mutex_lock_interruptible(&dd->ipath_eep_lock); if (!ret) { ret = ipath_eeprom_internal_read(dd, eeprom_offset, buff, len); mutex_unlock(&dd->ipath_eep_lock); } return ret; } /** * ipath_eeprom_write - writes data to the eeprom via I2C * @dd: the infinipath device * @eeprom_offset: where to place data * @buffer: data to write * @len: number of bytes to write */ int ipath_eeprom_write(struct ipath_devdata *dd, u8 eeprom_offset, const void *buff, int len) { int ret; ret = mutex_lock_interruptible(&dd->ipath_eep_lock); if (!ret) { ret = ipath_eeprom_internal_write(dd, eeprom_offset, buff, len); mutex_unlock(&dd->ipath_eep_lock); } return ret; } static u8 flash_csum(struct ipath_flash *ifp, int adjust) { u8 *ip = (u8 *) ifp; u8 csum = 0, len; /* * Limit length checksummed to max length of actual data. * Checksum of erased eeprom will still be bad, but we avoid * reading past the end of the buffer we were passed. */ len = ifp->if_length; if (len > sizeof(struct ipath_flash)) len = sizeof(struct ipath_flash); while (len--) csum += *ip++; csum -= ifp->if_csum; csum = ~csum; if (adjust) ifp->if_csum = csum; return csum; } /** * ipath_get_guid - get the GUID from the i2c device * @dd: the infinipath device * * We have the capability to use the ipath_nguid field, and get * the guid from the first chip's flash, to use for all of them. */ void ipath_get_eeprom_info(struct ipath_devdata *dd) { void *buf; struct ipath_flash *ifp; __be64 guid; int len, eep_stat; u8 csum, *bguid; int t = dd->ipath_unit; struct ipath_devdata *dd0 = ipath_lookup(0); if (t && dd0->ipath_nguid > 1 && t <= dd0->ipath_nguid) { u8 oguid; dd->ipath_guid = dd0->ipath_guid; bguid = (u8 *) & dd->ipath_guid; oguid = bguid[7]; bguid[7] += t; if (oguid > bguid[7]) { if (bguid[6] == 0xff) { if (bguid[5] == 0xff) { ipath_dev_err( dd, "Can't set %s GUID from " "base, wraps to OUI!\n", ipath_get_unit_name(t)); dd->ipath_guid = 0; goto bail; } bguid[5]++; } bguid[6]++; } dd->ipath_nguid = 1; ipath_dbg("nguid %u, so adding %u to device 0 guid, " "for %llx\n", dd0->ipath_nguid, t, (unsigned long long) be64_to_cpu(dd->ipath_guid)); goto bail; } /* * read full flash, not just currently used part, since it may have * been written with a newer definition * */ len = sizeof(struct ipath_flash); buf = vmalloc(len); if (!buf) { ipath_dev_err(dd, "Couldn't allocate memory to read %u " "bytes from eeprom for GUID\n", len); goto bail; } mutex_lock(&dd->ipath_eep_lock); eep_stat = ipath_eeprom_internal_read(dd, 0, buf, len); mutex_unlock(&dd->ipath_eep_lock); if (eep_stat) { ipath_dev_err(dd, "Failed reading GUID from eeprom\n"); goto done; } ifp = (struct ipath_flash *)buf; csum = flash_csum(ifp, 0); if (csum != ifp->if_csum) { dev_info(&dd->pcidev->dev, "Bad I2C flash checksum: " "0x%x, not 0x%x\n", csum, ifp->if_csum); goto done; } if (*(__be64 *) ifp->if_guid == cpu_to_be64(0) || *(__be64 *) ifp->if_guid == ~cpu_to_be64(0)) { ipath_dev_err(dd, "Invalid GUID %llx from flash; " "ignoring\n", *(unsigned long long *) ifp->if_guid); /* don't allow GUID if all 0 or all 1's */ goto done; } /* complain, but allow it */ if (*(u64 *) ifp->if_guid == 0x100007511000000ULL) dev_info(&dd->pcidev->dev, "Warning, GUID %llx is " "default, probably not correct!\n", *(unsigned long long *) ifp->if_guid); bguid = ifp->if_guid; if (!bguid[0] && !bguid[1] && !bguid[2]) { /* original incorrect GUID format in flash; fix in * core copy, by shifting up 2 octets; don't need to * change top octet, since both it and shifted are * 0.. */ bguid[1] = bguid[3]; bguid[2] = bguid[4]; bguid[3] = bguid[4] = 0; guid = *(__be64 *) ifp->if_guid; ipath_cdbg(VERBOSE, "Old GUID format in flash, top 3 zero, " "shifting 2 octets\n"); } else guid = *(__be64 *) ifp->if_guid; dd->ipath_guid = guid; dd->ipath_nguid = ifp->if_numguid; /* * Things are slightly complicated by the desire to transparently * support both the Pathscale 10-digit serial number and the QLogic * 13-character version. */ if ((ifp->if_fversion > 1) && ifp->if_sprefix[0] && ((u8 *)ifp->if_sprefix)[0] != 0xFF) { /* This board has a Serial-prefix, which is stored * elsewhere for backward-compatibility. */ char *snp = dd->ipath_serial; memcpy(snp, ifp->if_sprefix, sizeof ifp->if_sprefix); snp[sizeof ifp->if_sprefix] = '\0'; len = strlen(snp); snp += len; len = (sizeof dd->ipath_serial) - len; if (len > sizeof ifp->if_serial) { len = sizeof ifp->if_serial; } memcpy(snp, ifp->if_serial, len); } else memcpy(dd->ipath_serial, ifp->if_serial, sizeof ifp->if_serial); if (!strstr(ifp->if_comment, "Tested successfully")) ipath_dev_err(dd, "Board SN %s did not pass functional " "test: %s\n", dd->ipath_serial, ifp->if_comment); ipath_cdbg(VERBOSE, "Initted GUID to %llx from eeprom\n", (unsigned long long) be64_to_cpu(dd->ipath_guid)); memcpy(&dd->ipath_eep_st_errs, &ifp->if_errcntp, IPATH_EEP_LOG_CNT); /* * Power-on (actually "active") hours are kept as little-endian value * in EEPROM, but as seconds in a (possibly as small as 24-bit) * atomic_t while running. */ atomic_set(&dd->ipath_active_time, 0); dd->ipath_eep_hrs = ifp->if_powerhour[0] | (ifp->if_powerhour[1] << 8); done: vfree(buf); bail:; } /** * ipath_update_eeprom_log - copy active-time and error counters to eeprom * @dd: the infinipath device * * Although the time is kept as seconds in the ipath_devdata struct, it is * rounded to hours for re-write, as we have only 16 bits in EEPROM. * First-cut code reads whole (expected) struct ipath_flash, modifies, * re-writes. Future direction: read/write only what we need, assuming * that the EEPROM had to have been "good enough" for driver init, and * if not, we aren't making it worse. * */ int ipath_update_eeprom_log(struct ipath_devdata *dd) { void *buf; struct ipath_flash *ifp; int len, hi_water; uint32_t new_time, new_hrs; u8 csum; int ret, idx; unsigned long flags; /* first, check if we actually need to do anything. */ ret = 0; for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) { if (dd->ipath_eep_st_new_errs[idx]) { ret = 1; break; } } new_time = atomic_read(&dd->ipath_active_time); if (ret == 0 && new_time < 3600) return 0; /* * The quick-check above determined that there is something worthy * of logging, so get current contents and do a more detailed idea. * read full flash, not just currently used part, since it may have * been written with a newer definition */ len = sizeof(struct ipath_flash); buf = vmalloc(len); ret = 1; if (!buf) { ipath_dev_err(dd, "Couldn't allocate memory to read %u " "bytes from eeprom for logging\n", len); goto bail; } /* Grab semaphore and read current EEPROM. If we get an * error, let go, but if not, keep it until we finish write. */ ret = mutex_lock_interruptible(&dd->ipath_eep_lock); if (ret) { ipath_dev_err(dd, "Unable to acquire EEPROM for logging\n"); goto free_bail; } ret = ipath_eeprom_internal_read(dd, 0, buf, len); if (ret) { mutex_unlock(&dd->ipath_eep_lock); ipath_dev_err(dd, "Unable read EEPROM for logging\n"); goto free_bail; } ifp = (struct ipath_flash *)buf; csum = flash_csum(ifp, 0); if (csum != ifp->if_csum) { mutex_unlock(&dd->ipath_eep_lock); ipath_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n", csum, ifp->if_csum); ret = 1; goto free_bail; } hi_water = 0; spin_lock_irqsave(&dd->ipath_eep_st_lock, flags); for (idx = 0; idx < IPATH_EEP_LOG_CNT; ++idx) { int new_val = dd->ipath_eep_st_new_errs[idx]; if (new_val) { /* * If we have seen any errors, add to EEPROM values * We need to saturate at 0xFF (255) and we also * would need to adjust the checksum if we were * trying to minimize EEPROM traffic * Note that we add to actual current count in EEPROM, * in case it was altered while we were running. */ new_val += ifp->if_errcntp[idx]; if (new_val > 0xFF) new_val = 0xFF; if (ifp->if_errcntp[idx] != new_val) { ifp->if_errcntp[idx] = new_val; hi_water = offsetof(struct ipath_flash, if_errcntp) + idx; } /* * update our shadow (used to minimize EEPROM * traffic), to match what we are about to write. */ dd->ipath_eep_st_errs[idx] = new_val; dd->ipath_eep_st_new_errs[idx] = 0; } } /* * now update active-time. We would like to round to the nearest hour * but unless atomic_t are sure to be proper signed ints we cannot, * because we need to account for what we "transfer" to EEPROM and * if we log an hour at 31 minutes, then we would need to set * active_time to -29 to accurately count the _next_ hour. */ if (new_time >= 3600) { new_hrs = new_time / 3600; atomic_sub((new_hrs * 3600), &dd->ipath_active_time); new_hrs += dd->ipath_eep_hrs; if (new_hrs > 0xFFFF) new_hrs = 0xFFFF; dd->ipath_eep_hrs = new_hrs; if ((new_hrs & 0xFF) != ifp->if_powerhour[0]) { ifp->if_powerhour[0] = new_hrs & 0xFF; hi_water = offsetof(struct ipath_flash, if_powerhour); } if ((new_hrs >> 8) != ifp->if_powerhour[1]) { ifp->if_powerhour[1] = new_hrs >> 8; hi_water = offsetof(struct ipath_flash, if_powerhour) + 1; } } /* * There is a tiny possibility that we could somehow fail to write * the EEPROM after updating our shadows, but problems from holding * the spinlock too long are a much bigger issue. */ spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags); if (hi_water) { /* we made some change to the data, uopdate cksum and write */ csum = flash_csum(ifp, 1); ret = ipath_eeprom_internal_write(dd, 0, buf, hi_water + 1); } mutex_unlock(&dd->ipath_eep_lock); if (ret) ipath_dev_err(dd, "Failed updating EEPROM\n"); free_bail: vfree(buf); bail: return ret; } /** * ipath_inc_eeprom_err - increment one of the four error counters * that are logged to EEPROM. * @dd: the infinipath device * @eidx: 0..3, the counter to increment * @incr: how much to add * * Each counter is 8-bits, and saturates at 255 (0xFF). They * are copied to the EEPROM (aka flash) whenever ipath_update_eeprom_log() * is called, but it can only be called in a context that allows sleep. * This function can be called even at interrupt level. */ void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr) { uint new_val; unsigned long flags; spin_lock_irqsave(&dd->ipath_eep_st_lock, flags); new_val = dd->ipath_eep_st_new_errs[eidx] + incr; if (new_val > 255) new_val = 255; dd->ipath_eep_st_new_errs[eidx] = new_val; spin_unlock_irqrestore(&dd->ipath_eep_st_lock, flags); return; } static int ipath_tempsense_internal_read(struct ipath_devdata *dd, u8 regnum) { int ret; struct i2c_chain_desc *icd; ret = -ENOENT; icd = ipath_i2c_type(dd); if (!icd) goto bail; if (icd->temp_dev == IPATH_NO_DEV) { /* tempsense only exists on new, real-I2C boards */ ret = -ENXIO; goto bail; } if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) { ipath_dbg("Failed tempsense startcmd\n"); stop_cmd(dd); ret = -ENXIO; goto bail; } ret = wr_byte(dd, regnum); stop_cmd(dd); if (ret) { ipath_dev_err(dd, "Failed tempsense WR command %02X\n", regnum); ret = -ENXIO; goto bail; } if (i2c_startcmd(dd, icd->temp_dev | READ_CMD)) { ipath_dbg("Failed tempsense RD startcmd\n"); stop_cmd(dd); ret = -ENXIO; goto bail; } /* * We can only clock out one byte per command, sensibly */ ret = rd_byte(dd); stop_cmd(dd); bail: return ret; } #define VALID_TS_RD_REG_MASK 0xBF /** * ipath_tempsense_read - read register of temp sensor via I2C * @dd: the infinipath device * @regnum: register to read from * * returns reg contents (0..255) or < 0 for error */ int ipath_tempsense_read(struct ipath_devdata *dd, u8 regnum) { int ret; if (regnum > 7) return -EINVAL; /* return a bogus value for (the one) register we do not have */ if (!((1 << regnum) & VALID_TS_RD_REG_MASK)) return 0; ret = mutex_lock_interruptible(&dd->ipath_eep_lock); if (!ret) { ret = ipath_tempsense_internal_read(dd, regnum); mutex_unlock(&dd->ipath_eep_lock); } /* * There are three possibilities here: * ret is actual value (0..255) * ret is -ENXIO or -EINVAL from code in this file * ret is -EINTR from mutex_lock_interruptible. */ return ret; } static int ipath_tempsense_internal_write(struct ipath_devdata *dd, u8 regnum, u8 data) { int ret = -ENOENT; struct i2c_chain_desc *icd; icd = ipath_i2c_type(dd); if (!icd) goto bail; if (icd->temp_dev == IPATH_NO_DEV) { /* tempsense only exists on new, real-I2C boards */ ret = -ENXIO; goto bail; } if (i2c_startcmd(dd, icd->temp_dev | WRITE_CMD)) { ipath_dbg("Failed tempsense startcmd\n"); stop_cmd(dd); ret = -ENXIO; goto bail; } ret = wr_byte(dd, regnum); if (ret) { stop_cmd(dd); ipath_dev_err(dd, "Failed to write tempsense command %02X\n", regnum); ret = -ENXIO; goto bail; } ret = wr_byte(dd, data); stop_cmd(dd); ret = i2c_startcmd(dd, icd->temp_dev | READ_CMD); if (ret) { ipath_dev_err(dd, "Failed tempsense data wrt to %02X\n", regnum); ret = -ENXIO; } bail: return ret; } #define VALID_TS_WR_REG_MASK ((1 << 9) | (1 << 0xB) | (1 << 0xD)) /** * ipath_tempsense_write - write register of temp sensor via I2C * @dd: the infinipath device * @regnum: register to write * @data: data to write * * returns 0 for success or < 0 for error */ int ipath_tempsense_write(struct ipath_devdata *dd, u8 regnum, u8 data) { int ret; if (regnum > 15 || !((1 << regnum) & VALID_TS_WR_REG_MASK)) return -EINVAL; ret = mutex_lock_interruptible(&dd->ipath_eep_lock); if (!ret) { ret = ipath_tempsense_internal_write(dd, regnum, data); mutex_unlock(&dd->ipath_eep_lock); } /* * There are three possibilities here: * ret is 0 for success * ret is -ENXIO or -EINVAL from code in this file * ret is -EINTR from mutex_lock_interruptible. */ return ret; }