/* * Cypress APA trackpad with I2C interface * * Author: Dudley Du * Further cleanup and restructuring by: * Daniel Kurtz * Benson Leung * * Copyright (C) 2011-2015 Cypress Semiconductor, Inc. * Copyright (C) 2011-2012 Google, Inc. * * This file is subject to the terms and conditions of the GNU General Public * License. See the file COPYING in the main directory of this archive for * more details. */ #include #include #include #include #include #include #include #include "cyapa.h" #define GEN3_MAX_FINGERS 5 #define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07) #define BLK_HEAD_BYTES 32 /* Macro for register map group offset. */ #define PRODUCT_ID_SIZE 16 #define QUERY_DATA_SIZE 27 #define REG_PROTOCOL_GEN_QUERY_OFFSET 20 #define REG_OFFSET_DATA_BASE 0x0000 #define REG_OFFSET_COMMAND_BASE 0x0028 #define REG_OFFSET_QUERY_BASE 0x002a #define CYAPA_OFFSET_SOFT_RESET REG_OFFSET_COMMAND_BASE #define OP_RECALIBRATION_MASK 0x80 #define OP_REPORT_BASELINE_MASK 0x40 #define REG_OFFSET_MAX_BASELINE 0x0026 #define REG_OFFSET_MIN_BASELINE 0x0027 #define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1) #define SET_POWER_MODE_DELAY 10000 /* Unit: us */ #define SET_POWER_MODE_TRIES 5 #define GEN3_BL_CMD_CHECKSUM_SEED 0xff #define GEN3_BL_CMD_INITIATE_BL 0x38 #define GEN3_BL_CMD_WRITE_BLOCK 0x39 #define GEN3_BL_CMD_VERIFY_BLOCK 0x3a #define GEN3_BL_CMD_TERMINATE_BL 0x3b #define GEN3_BL_CMD_LAUNCH_APP 0xa5 /* * CYAPA trackpad device states. * Used in register 0x00, bit1-0, DeviceStatus field. * Other values indicate device is in an abnormal state and must be reset. */ #define CYAPA_DEV_NORMAL 0x03 #define CYAPA_DEV_BUSY 0x01 #define CYAPA_FW_BLOCK_SIZE 64 #define CYAPA_FW_READ_SIZE 16 #define CYAPA_FW_HDR_START 0x0780 #define CYAPA_FW_HDR_BLOCK_COUNT 2 #define CYAPA_FW_HDR_BLOCK_START (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE) #define CYAPA_FW_HDR_SIZE (CYAPA_FW_HDR_BLOCK_COUNT * \ CYAPA_FW_BLOCK_SIZE) #define CYAPA_FW_DATA_START 0x0800 #define CYAPA_FW_DATA_BLOCK_COUNT 480 #define CYAPA_FW_DATA_BLOCK_START (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE) #define CYAPA_FW_DATA_SIZE (CYAPA_FW_DATA_BLOCK_COUNT * \ CYAPA_FW_BLOCK_SIZE) #define CYAPA_FW_SIZE (CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE) #define CYAPA_CMD_LEN 16 #define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b #define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1) struct cyapa_touch { /* * high bits or x/y position value * bit 7 - 4: high 4 bits of x position value * bit 3 - 0: high 4 bits of y position value */ u8 xy_hi; u8 x_lo; /* low 8 bits of x position value. */ u8 y_lo; /* low 8 bits of y position value. */ u8 pressure; /* id range is 1 - 15. It is incremented with every new touch. */ u8 id; } __packed; struct cyapa_reg_data { /* * bit 0 - 1: device status * bit 3 - 2: power mode * bit 6 - 4: reserved * bit 7: interrupt valid bit */ u8 device_status; /* * bit 7 - 4: number of fingers currently touching pad * bit 3: valid data check bit * bit 2: middle mechanism button state if exists * bit 1: right mechanism button state if exists * bit 0: left mechanism button state if exists */ u8 finger_btn; /* CYAPA reports up to 5 touches per packet. */ struct cyapa_touch touches[5]; } __packed; struct gen3_write_block_cmd { u8 checksum_seed; /* Always be 0xff */ u8 cmd_code; /* command code: 0x39 */ u8 key[8]; /* 8-byte security key */ __be16 block_num; u8 block_data[CYAPA_FW_BLOCK_SIZE]; u8 block_checksum; /* Calculated using bytes 12 - 75 */ u8 cmd_checksum; /* Calculated using bytes 0-76 */ } __packed; static const u8 security_key[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 }; static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 }; static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 }; static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 }; /* for byte read/write command */ #define CMD_RESET 0 #define CMD_POWER_MODE 1 #define CMD_DEV_STATUS 2 #define CMD_REPORT_MAX_BASELINE 3 #define CMD_REPORT_MIN_BASELINE 4 #define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1) #define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET) #define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE) #define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS) #define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE) #define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE) /* for group registers read/write command */ #define REG_GROUP_DATA 0 #define REG_GROUP_CMD 2 #define REG_GROUP_QUERY 3 #define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3)) #define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA) #define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD) #define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY) /* for register block read/write command */ #define CMD_BL_STATUS 0 #define CMD_BL_HEAD 1 #define CMD_BL_CMD 2 #define CMD_BL_DATA 3 #define CMD_BL_ALL 4 #define CMD_BLK_PRODUCT_ID 5 #define CMD_BLK_HEAD 6 #define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1)) /* register block read/write command in bootloader mode */ #define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS) #define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD) #define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD) #define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA) #define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL) /* register block read/write command in operational mode */ #define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID) #define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD) struct cyapa_cmd_len { u8 cmd; u8 len; }; /* maps generic CYAPA_CMD_* code to the I2C equivalent */ static const struct cyapa_cmd_len cyapa_i2c_cmds[] = { { CYAPA_OFFSET_SOFT_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */ { REG_OFFSET_COMMAND_BASE + 1, 1 }, /* CYAPA_CMD_POWER_MODE */ { REG_OFFSET_DATA_BASE, 1 }, /* CYAPA_CMD_DEV_STATUS */ { REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) }, /* CYAPA_CMD_GROUP_DATA */ { REG_OFFSET_COMMAND_BASE, 0 }, /* CYAPA_CMD_GROUP_CMD */ { REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */ { BL_HEAD_OFFSET, 3 }, /* CYAPA_CMD_BL_STATUS */ { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_HEAD */ { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_CMD */ { BL_DATA_OFFSET, 16 }, /* CYAPA_CMD_BL_DATA */ { BL_HEAD_OFFSET, 32 }, /* CYAPA_CMD_BL_ALL */ { REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE }, /* CYAPA_CMD_BLK_PRODUCT_ID */ { REG_OFFSET_DATA_BASE, 32 }, /* CYAPA_CMD_BLK_HEAD */ { REG_OFFSET_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */ { REG_OFFSET_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */ }; static const struct cyapa_cmd_len cyapa_smbus_cmds[] = { { CYAPA_SMBUS_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */ { CYAPA_SMBUS_POWER_MODE, 1 }, /* CYAPA_CMD_POWER_MODE */ { CYAPA_SMBUS_DEV_STATUS, 1 }, /* CYAPA_CMD_DEV_STATUS */ { CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) }, /* CYAPA_CMD_GROUP_DATA */ { CYAPA_SMBUS_GROUP_CMD, 2 }, /* CYAPA_CMD_GROUP_CMD */ { CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */ { CYAPA_SMBUS_BL_STATUS, 3 }, /* CYAPA_CMD_BL_STATUS */ { CYAPA_SMBUS_BL_HEAD, 16 }, /* CYAPA_CMD_BL_HEAD */ { CYAPA_SMBUS_BL_CMD, 16 }, /* CYAPA_CMD_BL_CMD */ { CYAPA_SMBUS_BL_DATA, 16 }, /* CYAPA_CMD_BL_DATA */ { CYAPA_SMBUS_BL_ALL, 32 }, /* CYAPA_CMD_BL_ALL */ { CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE }, /* CYAPA_CMD_BLK_PRODUCT_ID */ { CYAPA_SMBUS_BLK_HEAD, 16 }, /* CYAPA_CMD_BLK_HEAD */ { CYAPA_SMBUS_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */ { CYAPA_SMBUS_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */ }; static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa); /* * cyapa_smbus_read_block - perform smbus block read command * @cyapa - private data structure of the driver * @cmd - the properly encoded smbus command * @len - expected length of smbus command result * @values - buffer to store smbus command result * * Returns negative errno, else the number of bytes written. * * Note: * In trackpad device, the memory block allocated for I2C register map * is 256 bytes, so the max read block for I2C bus is 256 bytes. */ ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len, u8 *values) { ssize_t ret; u8 index; u8 smbus_cmd; u8 *buf; struct i2c_client *client = cyapa->client; if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd)) return -EINVAL; if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) { /* read specific block registers command. */ smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ); ret = i2c_smbus_read_block_data(client, smbus_cmd, values); goto out; } ret = 0; for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) { smbus_cmd = SMBUS_ENCODE_IDX(cmd, index); smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ); buf = values + I2C_SMBUS_BLOCK_MAX * index; ret = i2c_smbus_read_block_data(client, smbus_cmd, buf); if (ret < 0) goto out; } out: return ret > 0 ? len : ret; } static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx) { u8 cmd; if (cyapa->smbus) { cmd = cyapa_smbus_cmds[cmd_idx].cmd; cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ); } else { cmd = cyapa_i2c_cmds[cmd_idx].cmd; } return i2c_smbus_read_byte_data(cyapa->client, cmd); } static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value) { u8 cmd; if (cyapa->smbus) { cmd = cyapa_smbus_cmds[cmd_idx].cmd; cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE); } else { cmd = cyapa_i2c_cmds[cmd_idx].cmd; } return i2c_smbus_write_byte_data(cyapa->client, cmd, value); } ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len, u8 *values) { return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values); } static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg, size_t len, const u8 *values) { return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values); } ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values) { u8 cmd; size_t len; if (cyapa->smbus) { cmd = cyapa_smbus_cmds[cmd_idx].cmd; len = cyapa_smbus_cmds[cmd_idx].len; return cyapa_smbus_read_block(cyapa, cmd, len, values); } cmd = cyapa_i2c_cmds[cmd_idx].cmd; len = cyapa_i2c_cmds[cmd_idx].len; return cyapa_i2c_reg_read_block(cyapa, cmd, len, values); } /* * Determine the Gen3 trackpad device's current operating state. * */ static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len) { cyapa->state = CYAPA_STATE_NO_DEVICE; /* Parse based on Gen3 characteristic registers and bits */ if (reg_data[REG_BL_FILE] == BL_FILE && reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE && (reg_data[REG_BL_STATUS] == (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) || reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) { /* * Normal state after power on or reset, * REG_BL_STATUS == 0x11, firmware image checksum is valid. * REG_BL_STATUS == 0x10, firmware image checksum is invalid. */ cyapa->gen = CYAPA_GEN3; cyapa->state = CYAPA_STATE_BL_IDLE; } else if (reg_data[REG_BL_FILE] == BL_FILE && (reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) == BL_STATUS_RUNNING) { cyapa->gen = CYAPA_GEN3; if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) { cyapa->state = CYAPA_STATE_BL_BUSY; } else { if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) == BL_ERROR_BOOTLOADING) cyapa->state = CYAPA_STATE_BL_ACTIVE; else cyapa->state = CYAPA_STATE_BL_IDLE; } } else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) && (reg_data[REG_OP_DATA1] & OP_DATA_VALID)) { /* * Normal state when running in operational mode, * may also not in full power state or * busying in command process. */ if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <= GEN3_MAX_FINGERS) { /* Finger number data is valid. */ cyapa->gen = CYAPA_GEN3; cyapa->state = CYAPA_STATE_OP; } } else if (reg_data[REG_OP_STATUS] == 0x0C && reg_data[REG_OP_DATA1] == 0x08) { /* Op state when first two registers overwritten with 0x00 */ cyapa->gen = CYAPA_GEN3; cyapa->state = CYAPA_STATE_OP; } else if (reg_data[REG_BL_STATUS] & (BL_STATUS_RUNNING | BL_STATUS_BUSY)) { cyapa->gen = CYAPA_GEN3; cyapa->state = CYAPA_STATE_BL_BUSY; } if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP || cyapa->state == CYAPA_STATE_BL_IDLE || cyapa->state == CYAPA_STATE_BL_ACTIVE || cyapa->state == CYAPA_STATE_BL_BUSY)) return 0; return -EAGAIN; } /* * Enter bootloader by soft resetting the device. * * If device is already in the bootloader, the function just returns. * Otherwise, reset the device; after reset, device enters bootloader idle * state immediately. * * Returns: * 0 on success * -EAGAIN device was reset, but is not now in bootloader idle state * < 0 if the device never responds within the timeout */ static int cyapa_gen3_bl_enter(struct cyapa *cyapa) { int error; int waiting_time; error = cyapa_poll_state(cyapa, 500); if (error) return error; if (cyapa->state == CYAPA_STATE_BL_IDLE) { /* Already in BL_IDLE. Skipping reset. */ return 0; } if (cyapa->state != CYAPA_STATE_OP) return -EAGAIN; cyapa->operational = false; cyapa->state = CYAPA_STATE_NO_DEVICE; error = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, 0x01); if (error) return -EIO; usleep_range(25000, 50000); waiting_time = 2000; /* For some shipset, max waiting time is 1~2s. */ do { error = cyapa_poll_state(cyapa, 500); if (error) { if (error == -ETIMEDOUT) { waiting_time -= 500; continue; } return error; } if ((cyapa->state == CYAPA_STATE_BL_IDLE) && !(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG)) break; msleep(100); waiting_time -= 100; } while (waiting_time > 0); if ((cyapa->state != CYAPA_STATE_BL_IDLE) || (cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG)) return -EAGAIN; return 0; } static int cyapa_gen3_bl_activate(struct cyapa *cyapa) { int error; error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_activate), bl_activate); if (error) return error; /* Wait for bootloader to activate; takes between 2 and 12 seconds */ msleep(2000); error = cyapa_poll_state(cyapa, 11000); if (error) return error; if (cyapa->state != CYAPA_STATE_BL_ACTIVE) return -EAGAIN; return 0; } static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa) { int error; error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate), bl_deactivate); if (error) return error; /* Wait for bootloader to switch to idle state; should take < 100ms */ msleep(100); error = cyapa_poll_state(cyapa, 500); if (error) return error; if (cyapa->state != CYAPA_STATE_BL_IDLE) return -EAGAIN; return 0; } /* * Exit bootloader * * Send bl_exit command, then wait 50 - 100 ms to let device transition to * operational mode. If this is the first time the device's firmware is * running, it can take up to 2 seconds to calibrate its sensors. So, poll * the device's new state for up to 2 seconds. * * Returns: * -EIO failure while reading from device * -EAGAIN device is stuck in bootloader, b/c it has invalid firmware * 0 device is supported and in operational mode */ static int cyapa_gen3_bl_exit(struct cyapa *cyapa) { int error; error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit); if (error) return error; /* * Wait for bootloader to exit, and operation mode to start. * Normally, this takes at least 50 ms. */ msleep(50); /* * In addition, when a device boots for the first time after being * updated to new firmware, it must first calibrate its sensors, which * can take up to an additional 2 seconds. If the device power is * running low, this may take even longer. */ error = cyapa_poll_state(cyapa, 4000); if (error < 0) return error; if (cyapa->state != CYAPA_STATE_OP) return -EAGAIN; return 0; } static u16 cyapa_gen3_csum(const u8 *buf, size_t count) { int i; u16 csum = 0; for (i = 0; i < count; i++) csum += buf[i]; return csum; } /* * Verify the integrity of a CYAPA firmware image file. * * The firmware image file is 30848 bytes, composed of 482 64-byte blocks. * * The first 2 blocks are the firmware header. * The next 480 blocks are the firmware image. * * The first two bytes of the header hold the header checksum, computed by * summing the other 126 bytes of the header. * The last two bytes of the header hold the firmware image checksum, computed * by summing the 30720 bytes of the image modulo 0xffff. * * Both checksums are stored little-endian. */ static int cyapa_gen3_check_fw(struct cyapa *cyapa, const struct firmware *fw) { struct device *dev = &cyapa->client->dev; u16 csum; u16 csum_expected; /* Firmware must match exact 30848 bytes = 482 64-byte blocks. */ if (fw->size != CYAPA_FW_SIZE) { dev_err(dev, "invalid firmware size = %zu, expected %u.\n", fw->size, CYAPA_FW_SIZE); return -EINVAL; } /* Verify header block */ csum_expected = (fw->data[0] << 8) | fw->data[1]; csum = cyapa_gen3_csum(&fw->data[2], CYAPA_FW_HDR_SIZE - 2); if (csum != csum_expected) { dev_err(dev, "%s %04x, expected: %04x\n", "invalid firmware header checksum = ", csum, csum_expected); return -EINVAL; } /* Verify firmware image */ csum_expected = (fw->data[CYAPA_FW_HDR_SIZE - 2] << 8) | fw->data[CYAPA_FW_HDR_SIZE - 1]; csum = cyapa_gen3_csum(&fw->data[CYAPA_FW_HDR_SIZE], CYAPA_FW_DATA_SIZE); if (csum != csum_expected) { dev_err(dev, "%s %04x, expected: %04x\n", "invalid firmware header checksum = ", csum, csum_expected); return -EINVAL; } return 0; } /* * Write a |len| byte long buffer |buf| to the device, by chopping it up into a * sequence of smaller |CYAPA_CMD_LEN|-length write commands. * * The data bytes for a write command are prepended with the 1-byte offset * of the data relative to the start of |buf|. */ static int cyapa_gen3_write_buffer(struct cyapa *cyapa, const u8 *buf, size_t len) { int error; size_t i; unsigned char cmd[CYAPA_CMD_LEN + 1]; size_t cmd_len; for (i = 0; i < len; i += CYAPA_CMD_LEN) { const u8 *payload = &buf[i]; cmd_len = (len - i >= CYAPA_CMD_LEN) ? CYAPA_CMD_LEN : len - i; cmd[0] = i; memcpy(&cmd[1], payload, cmd_len); error = cyapa_i2c_reg_write_block(cyapa, 0, cmd_len + 1, cmd); if (error) return error; } return 0; } /* * A firmware block write command writes 64 bytes of data to a single flash * page in the device. The 78-byte block write command has the format: * <0xff> * * <0xff> - every command starts with 0xff * - the write command value is 0x39 * - write commands include an 8-byte key: { 00 01 02 03 04 05 06 07 } * - Memory Block number (address / 64) (16-bit, big-endian) * - 64 bytes of firmware image data * - sum of 64 bytes, modulo 0xff * - sum of 77 bytes, from 0xff to * * Each write command is split into 5 i2c write transactions of up to 16 bytes. * Each transaction starts with an i2c register offset: (00, 10, 20, 30, 40). */ static int cyapa_gen3_write_fw_block(struct cyapa *cyapa, u16 block, const u8 *data) { int ret; struct gen3_write_block_cmd write_block_cmd; u8 status[BL_STATUS_SIZE]; int tries; u8 bl_status, bl_error; /* Set write command and security key bytes. */ write_block_cmd.checksum_seed = GEN3_BL_CMD_CHECKSUM_SEED; write_block_cmd.cmd_code = GEN3_BL_CMD_WRITE_BLOCK; memcpy(write_block_cmd.key, security_key, sizeof(security_key)); put_unaligned_be16(block, &write_block_cmd.block_num); memcpy(write_block_cmd.block_data, data, CYAPA_FW_BLOCK_SIZE); write_block_cmd.block_checksum = cyapa_gen3_csum( write_block_cmd.block_data, CYAPA_FW_BLOCK_SIZE); write_block_cmd.cmd_checksum = cyapa_gen3_csum((u8 *)&write_block_cmd, sizeof(write_block_cmd) - 1); ret = cyapa_gen3_write_buffer(cyapa, (u8 *)&write_block_cmd, sizeof(write_block_cmd)); if (ret) return ret; /* Wait for write to finish */ tries = 11; /* Programming for one block can take about 100ms. */ do { usleep_range(10000, 20000); /* Check block write command result status. */ ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, BL_STATUS_SIZE, status); if (ret != BL_STATUS_SIZE) return (ret < 0) ? ret : -EIO; } while ((status[REG_BL_STATUS] & BL_STATUS_BUSY) && --tries); /* Ignore WATCHDOG bit and reserved bits. */ bl_status = status[REG_BL_STATUS] & ~BL_STATUS_REV_MASK; bl_error = status[REG_BL_ERROR] & ~BL_ERROR_RESERVED; if (bl_status & BL_STATUS_BUSY) ret = -ETIMEDOUT; else if (bl_status != BL_STATUS_RUNNING || bl_error != BL_ERROR_BOOTLOADING) ret = -EIO; else ret = 0; return ret; } static int cyapa_gen3_write_blocks(struct cyapa *cyapa, size_t start_block, size_t block_count, const u8 *image_data) { int error; int i; for (i = 0; i < block_count; i++) { size_t block = start_block + i; size_t addr = i * CYAPA_FW_BLOCK_SIZE; const u8 *data = &image_data[addr]; error = cyapa_gen3_write_fw_block(cyapa, block, data); if (error) return error; } return 0; } static int cyapa_gen3_do_fw_update(struct cyapa *cyapa, const struct firmware *fw) { struct device *dev = &cyapa->client->dev; int error; /* First write data, starting at byte 128 of fw->data */ error = cyapa_gen3_write_blocks(cyapa, CYAPA_FW_DATA_BLOCK_START, CYAPA_FW_DATA_BLOCK_COUNT, &fw->data[CYAPA_FW_HDR_BLOCK_COUNT * CYAPA_FW_BLOCK_SIZE]); if (error) { dev_err(dev, "FW update aborted, write image: %d\n", error); return error; } /* Then write checksum */ error = cyapa_gen3_write_blocks(cyapa, CYAPA_FW_HDR_BLOCK_START, CYAPA_FW_HDR_BLOCK_COUNT, &fw->data[0]); if (error) { dev_err(dev, "FW update aborted, write checksum: %d\n", error); return error; } return 0; } static ssize_t cyapa_gen3_do_calibrate(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct cyapa *cyapa = dev_get_drvdata(dev); unsigned long timeout; int ret; ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); if (ret < 0) { dev_err(dev, "Error reading dev status: %d\n", ret); goto out; } if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) { dev_warn(dev, "Trackpad device is busy, device state: 0x%02x\n", ret); ret = -EAGAIN; goto out; } ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, OP_RECALIBRATION_MASK); if (ret < 0) { dev_err(dev, "Failed to send calibrate command: %d\n", ret); goto out; } /* max recalibration timeout 2s. */ timeout = jiffies + 2 * HZ; do { /* * For this recalibration, the max time will not exceed 2s. * The average time is approximately 500 - 700 ms, and we * will check the status every 100 - 200ms. */ msleep(100); ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); if (ret < 0) { dev_err(dev, "Error reading dev status: %d\n", ret); goto out; } if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL) { dev_dbg(dev, "Calibration successful.\n"); goto out; } } while (time_is_after_jiffies(timeout)); dev_err(dev, "Failed to calibrate. Timeout.\n"); ret = -ETIMEDOUT; out: return ret < 0 ? ret : count; } static ssize_t cyapa_gen3_show_baseline(struct device *dev, struct device_attribute *attr, char *buf) { struct cyapa *cyapa = dev_get_drvdata(dev); int max_baseline, min_baseline; int tries; int ret; ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); if (ret < 0) { dev_err(dev, "Error reading dev status. err = %d\n", ret); goto out; } if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) { dev_warn(dev, "Trackpad device is busy. device state = 0x%x\n", ret); ret = -EAGAIN; goto out; } ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, OP_REPORT_BASELINE_MASK); if (ret < 0) { dev_err(dev, "Failed to send report baseline command. %d\n", ret); goto out; } tries = 3; /* Try for 30 to 60 ms */ do { usleep_range(10000, 20000); ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); if (ret < 0) { dev_err(dev, "Error reading dev status. err = %d\n", ret); goto out; } if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL) break; } while (--tries); if (tries == 0) { dev_err(dev, "Device timed out going to Normal state.\n"); ret = -ETIMEDOUT; goto out; } ret = cyapa_read_byte(cyapa, CYAPA_CMD_MAX_BASELINE); if (ret < 0) { dev_err(dev, "Failed to read max baseline. err = %d\n", ret); goto out; } max_baseline = ret; ret = cyapa_read_byte(cyapa, CYAPA_CMD_MIN_BASELINE); if (ret < 0) { dev_err(dev, "Failed to read min baseline. err = %d\n", ret); goto out; } min_baseline = ret; dev_dbg(dev, "Baseline report successful. Max: %d Min: %d\n", max_baseline, min_baseline); ret = scnprintf(buf, PAGE_SIZE, "%d %d\n", max_baseline, min_baseline); out: return ret; } /* * cyapa_get_wait_time_for_pwr_cmd * * Compute the amount of time we need to wait after updating the touchpad * power mode. The touchpad needs to consume the incoming power mode set * command at the current clock rate. */ static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode) { switch (pwr_mode) { case PWR_MODE_FULL_ACTIVE: return 20; case PWR_MODE_BTN_ONLY: return 20; case PWR_MODE_OFF: return 20; default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50; } } /* * Set device power mode * * Write to the field to configure power state. Power states include : * Full : Max scans and report rate. * Idle : Report rate set by user specified time. * ButtonOnly : No scans for fingers. When the button is triggered, * a slave interrupt is asserted to notify host to wake up. * Off : Only awake for i2c commands from host. No function for button * or touch sensors. * * The power_mode command should conform to the following : * Full : 0x3f * Idle : Configurable from 20 to 1000ms. See note below for * cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time * ButtonOnly : 0x01 * Off : 0x00 * * Device power mode can only be set when device is in operational mode. */ static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode, u16 always_unused, enum cyapa_pm_stage pm_stage) { struct input_dev *input = cyapa->input; u8 power; int tries; int sleep_time; int interval; int ret; if (cyapa->state != CYAPA_STATE_OP) return 0; tries = SET_POWER_MODE_TRIES; while (tries--) { ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE); if (ret >= 0) break; usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY); } if (ret < 0) return ret; /* * Return early if the power mode to set is the same as the current * one. */ if ((ret & PWR_MODE_MASK) == power_mode) return 0; sleep_time = (int)cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK); power = ret; power &= ~PWR_MODE_MASK; power |= power_mode & PWR_MODE_MASK; tries = SET_POWER_MODE_TRIES; while (tries--) { ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power); if (!ret) break; usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY); } /* * Wait for the newly set power command to go in at the previous * clock speed (scanrate) used by the touchpad firmware. Not * doing so before issuing the next command may result in errors * depending on the command's content. */ if (cyapa->operational && input && input->users && (pm_stage == CYAPA_PM_RUNTIME_SUSPEND || pm_stage == CYAPA_PM_RUNTIME_RESUME)) { /* Try to polling in 120Hz, read may fail, just ignore it. */ interval = 1000 / 120; while (sleep_time > 0) { if (sleep_time > interval) msleep(interval); else msleep(sleep_time); sleep_time -= interval; cyapa_gen3_try_poll_handler(cyapa); } } else { msleep(sleep_time); } return ret; } static int cyapa_gen3_set_proximity(struct cyapa *cyapa, bool enable) { return -EOPNOTSUPP; } static int cyapa_gen3_get_query_data(struct cyapa *cyapa) { u8 query_data[QUERY_DATA_SIZE]; int ret; if (cyapa->state != CYAPA_STATE_OP) return -EBUSY; ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data); if (ret != QUERY_DATA_SIZE) return (ret < 0) ? ret : -EIO; memcpy(&cyapa->product_id[0], &query_data[0], 5); cyapa->product_id[5] = '-'; memcpy(&cyapa->product_id[6], &query_data[5], 6); cyapa->product_id[12] = '-'; memcpy(&cyapa->product_id[13], &query_data[11], 2); cyapa->product_id[15] = '\0'; cyapa->fw_maj_ver = query_data[15]; cyapa->fw_min_ver = query_data[16]; cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK; cyapa->gen = query_data[20] & 0x0f; cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22]; cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23]; cyapa->physical_size_x = ((query_data[24] & 0xf0) << 4) | query_data[25]; cyapa->physical_size_y = ((query_data[24] & 0x0f) << 8) | query_data[26]; cyapa->max_z = 255; return 0; } static int cyapa_gen3_bl_query_data(struct cyapa *cyapa) { u8 bl_data[CYAPA_CMD_LEN]; int ret; ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data); if (ret != CYAPA_CMD_LEN) return (ret < 0) ? ret : -EIO; /* * This value will be updated again when entered application mode. * If TP failed to enter application mode, this fw version values * can be used as a reference. * This firmware version valid when fw image checksum is valid. */ if (bl_data[REG_BL_STATUS] == (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) { cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET]; cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET]; } return 0; } /* * Check if device is operational. * * An operational device is responding, has exited bootloader, and has * firmware supported by this driver. * * Returns: * -EBUSY no device or in bootloader * -EIO failure while reading from device * -EAGAIN device is still in bootloader * if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware * -EINVAL device is in operational mode, but not supported by this driver * 0 device is supported */ static int cyapa_gen3_do_operational_check(struct cyapa *cyapa) { struct device *dev = &cyapa->client->dev; int error; switch (cyapa->state) { case CYAPA_STATE_BL_ACTIVE: error = cyapa_gen3_bl_deactivate(cyapa); if (error) { dev_err(dev, "failed to bl_deactivate: %d\n", error); return error; } /* Fall through */ case CYAPA_STATE_BL_IDLE: /* Try to get firmware version in bootloader mode. */ cyapa_gen3_bl_query_data(cyapa); error = cyapa_gen3_bl_exit(cyapa); if (error) { dev_err(dev, "failed to bl_exit: %d\n", error); return error; } /* Fall through */ case CYAPA_STATE_OP: /* * Reading query data before going back to the full mode * may cause problems, so we set the power mode first here. */ error = cyapa_gen3_set_power_mode(cyapa, PWR_MODE_FULL_ACTIVE, 0, CYAPA_PM_ACTIVE); if (error) dev_err(dev, "%s: set full power mode failed: %d\n", __func__, error); error = cyapa_gen3_get_query_data(cyapa); if (error < 0) return error; /* Only support firmware protocol gen3 */ if (cyapa->gen != CYAPA_GEN3) { dev_err(dev, "unsupported protocol version (%d)", cyapa->gen); return -EINVAL; } /* Only support product ID starting with CYTRA */ if (memcmp(cyapa->product_id, product_id, strlen(product_id)) != 0) { dev_err(dev, "unsupported product ID (%s)\n", cyapa->product_id); return -EINVAL; } return 0; default: return -EIO; } return 0; } /* * Return false, do not continue process * Return true, continue process. */ static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa) { /* Not gen3 irq command response, skip for continue. */ if (cyapa->gen != CYAPA_GEN3) return true; if (cyapa->operational) return true; /* * Driver in detecting or other interface function processing, * so, stop cyapa_gen3_irq_handler to continue process to * avoid unwanted to error detecting and processing. * * And also, avoid the periodically asserted interrupts to be processed * as touch inputs when gen3 failed to launch into application mode, * which will cause gen3 stays in bootloader mode. */ return false; } static int cyapa_gen3_event_process(struct cyapa *cyapa, struct cyapa_reg_data *data) { struct input_dev *input = cyapa->input; int num_fingers; int i; num_fingers = (data->finger_btn >> 4) & 0x0f; for (i = 0; i < num_fingers; i++) { const struct cyapa_touch *touch = &data->touches[i]; /* Note: touch->id range is 1 to 15; slots are 0 to 14. */ int slot = touch->id - 1; input_mt_slot(input, slot); input_mt_report_slot_state(input, MT_TOOL_FINGER, true); input_report_abs(input, ABS_MT_POSITION_X, ((touch->xy_hi & 0xf0) << 4) | touch->x_lo); input_report_abs(input, ABS_MT_POSITION_Y, ((touch->xy_hi & 0x0f) << 8) | touch->y_lo); input_report_abs(input, ABS_MT_PRESSURE, touch->pressure); } input_mt_sync_frame(input); if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK) input_report_key(input, BTN_LEFT, !!(data->finger_btn & OP_DATA_LEFT_BTN)); if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK) input_report_key(input, BTN_MIDDLE, !!(data->finger_btn & OP_DATA_MIDDLE_BTN)); if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK) input_report_key(input, BTN_RIGHT, !!(data->finger_btn & OP_DATA_RIGHT_BTN)); input_sync(input); return 0; } static int cyapa_gen3_irq_handler(struct cyapa *cyapa) { struct device *dev = &cyapa->client->dev; struct cyapa_reg_data data; int ret; ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data); if (ret != sizeof(data)) { dev_err(dev, "failed to read report data, (%d)\n", ret); return -EINVAL; } if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC || (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL || (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) { dev_err(dev, "invalid device state bytes: %02x %02x\n", data.device_status, data.finger_btn); return -EINVAL; } return cyapa_gen3_event_process(cyapa, &data); } /* * This function will be called in the cyapa_gen3_set_power_mode function, * and it's known that it may failed in some situation after the set power * mode command was sent. So this function is aimed to avoid the knwon * and unwanted output I2C and data parse error messages. */ static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa) { struct cyapa_reg_data data; int ret; ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data); if (ret != sizeof(data)) return -EINVAL; if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC || (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL || (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) return -EINVAL; return cyapa_gen3_event_process(cyapa, &data); } static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; } static int cyapa_gen3_bl_initiate(struct cyapa *cyapa, const struct firmware *fw) { return 0; } static int cyapa_gen3_empty_output_data(struct cyapa *cyapa, u8 *buf, int *len, cb_sort func) { return 0; } const struct cyapa_dev_ops cyapa_gen3_ops = { .check_fw = cyapa_gen3_check_fw, .bl_enter = cyapa_gen3_bl_enter, .bl_activate = cyapa_gen3_bl_activate, .update_fw = cyapa_gen3_do_fw_update, .bl_deactivate = cyapa_gen3_bl_deactivate, .bl_initiate = cyapa_gen3_bl_initiate, .show_baseline = cyapa_gen3_show_baseline, .calibrate_store = cyapa_gen3_do_calibrate, .initialize = cyapa_gen3_initialize, .state_parse = cyapa_gen3_state_parse, .operational_check = cyapa_gen3_do_operational_check, .irq_handler = cyapa_gen3_irq_handler, .irq_cmd_handler = cyapa_gen3_irq_cmd_handler, .sort_empty_output_data = cyapa_gen3_empty_output_data, .set_power_mode = cyapa_gen3_set_power_mode, .set_proximity = cyapa_gen3_set_proximity, };