/* * defines, etc for the seeq8005 */ /* * This file is distributed under GPL. * * This style and layout of this file is also copied * from many of the other linux network device drivers. */ /* The number of low I/O ports used by the ethercard. */ #define SEEQ8005_IO_EXTENT 16 #define SEEQ_B (ioaddr) #define SEEQ_CMD (SEEQ_B) /* Write only */ #define SEEQ_STATUS (SEEQ_B) /* Read only */ #define SEEQ_CFG1 (SEEQ_B + 2) #define SEEQ_CFG2 (SEEQ_B + 4) #define SEEQ_REA (SEEQ_B + 6) /* Receive End Area Register */ #define SEEQ_RPR (SEEQ_B + 10) /* Receive Pointer Register */ #define SEEQ_TPR (SEEQ_B + 12) /* Transmit Pointer Register */ #define SEEQ_DMAAR (SEEQ_B + 14) /* DMA Address Register */ #define SEEQ_BUFFER (SEEQ_B + 8) /* Buffer Window Register */ #define DEFAULT_TEA (0x3f) #define SEEQCMD_DMA_INT_EN (0x0001) /* DMA Interrupt Enable */ #define SEEQCMD_RX_INT_EN (0x0002) /* Receive Interrupt Enable */ #define SEEQCMD_TX_INT_EN (0x0004) /* Transmit Interrupt Enable */ #define SEEQCMD_WINDOW_INT_EN (0x0008) /* What the hell is this for?? */ #define SEEQCMD_INT_MASK (0x000f) #define SEEQCMD_DMA_INT_ACK (0x0010) /* DMA ack */ #define SEEQCMD_RX_INT_ACK (0x0020) #define SEEQCMD_TX_INT_ACK (0x0040) #define SEEQCMD_WINDOW_INT_ACK (0x0080) #define SEEQCMD_ACK_ALL (0x00f0) #define SEEQCMD_SET_DMA_ON (0x0100) /* Enables DMA Request logic */ #define SEEQCMD_SET_RX_ON (0x0200) /* Enables Packet RX */ #define SEEQCMD_SET_TX_ON (0x0400) /* Starts TX run */ #define SEEQCMD_SET_DMA_OFF (0x0800) #define SEEQCMD_SET_RX_OFF (0x1000) #define SEEQCMD_SET_TX_OFF (0x2000) #define SEEQCMD_SET_ALL_OFF (0x3800) /* set all logic off */ #define SEEQCMD_FIFO_READ (0x4000) /* Set FIFO to read mode (read from Buffer) */ #define SEEQCMD_FIFO_WRITE (0x8000) /* Set FIFO to write mode */ #define SEEQSTAT_DMA_INT_EN (0x0001) /* Status of interrupt enable */ #define SEEQSTAT_RX_INT_EN (0x0002) #define SEEQSTAT_TX_INT_EN (0x0004) #define SEEQSTAT_WINDOW_INT_EN (0x0008) #define SEEQSTAT_DMA_INT (0x0010) /* Interrupt flagged */ #define SEEQSTAT_RX_INT (0x0020) #define SEEQSTAT_TX_INT (0x0040) #define SEEQSTAT_WINDOW_INT (0x0080) #define SEEQSTAT_ANY_INT (0x00f0) #define SEEQSTAT_DMA_ON (0x0100) /* DMA logic on */ #define SEEQSTAT_RX_ON (0x0200) /* Packet RX on */ #define SEEQSTAT_TX_ON (0x0400) /* TX running */ #define SEEQSTAT_FIFO_FULL (0x2000) #define SEEQSTAT_FIFO_EMPTY (0x4000) #define SEEQSTAT_FIFO_DIR (0x8000) /* 1=read, 0=write */ #define SEEQCFG1_BUFFER_MASK (0x000f) /* define what maps into the BUFFER register */ #define SEEQCFG1_BUFFER_MAC0 (0x0000) /* MAC station addresses 0-5 */ #define SEEQCFG1_BUFFER_MAC1 (0x0001) #define SEEQCFG1_BUFFER_MAC2 (0x0002) #define SEEQCFG1_BUFFER_MAC3 (0x0003) #define SEEQCFG1_BUFFER_MAC4 (0x0004) #define SEEQCFG1_BUFFER_MAC5 (0x0005) #define SEEQCFG1_BUFFER_PROM (0x0006) /* The Address/CFG PROM */ #define SEEQCFG1_BUFFER_TEA (0x0007) /* Transmit end area */ #define SEEQCFG1_BUFFER_BUFFER (0x0008) /* Packet buffer memory */ #define SEEQCFG1_BUFFER_INT_VEC (0x0009) /* Interrupt Vector */ #define SEEQCFG1_DMA_INTVL_MASK (0x0030) #define SEEQCFG1_DMA_CONT (0x0000) #define SEEQCFG1_DMA_800ns (0x0010) #define SEEQCFG1_DMA_1600ns (0x0020) #define SEEQCFG1_DMA_3200ns (0x0030) #define SEEQCFG1_DMA_LEN_MASK (0x00c0) #define SEEQCFG1_DMA_LEN1 (0x0000) #define SEEQCFG1_DMA_LEN2 (0x0040) #define SEEQCFG1_DMA_LEN4 (0x0080) #define SEEQCFG1_DMA_LEN8 (0x00c0) #define SEEQCFG1_MAC_MASK (0x3f00) /* Dis/enable bits for MAC addresses */ #define SEEQCFG1_MAC0_EN (0x0100) #define SEEQCFG1_MAC1_EN (0x0200) #define SEEQCFG1_MAC2_EN (0x0400) #define SEEQCFG1_MAC3_EN (0x0800) #define SEEQCFG1_MAC4_EN (0x1000) #define SEEQCFG1_MAC5_EN (0x2000) #define SEEQCFG1_MATCH_MASK (0xc000) /* Packet matching logic cfg bits */ #define SEEQCFG1_MATCH_SPECIFIC (0x0000) /* only matching MAC addresses */ #define SEEQCFG1_MATCH_BROAD (0x4000) /* matching and broadcast addresses */ #define SEEQCFG1_MATCH_MULTI (0x8000) /* matching, broadcast and multicast */ #define SEEQCFG1_MATCH_ALL (0xc000) /* Promiscuous mode */ #define SEEQCFG1_DEFAULT (SEEQCFG1_BUFFER_BUFFER | SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD) #define SEEQCFG2_BYTE_SWAP (0x0001) /* 0=Intel byte-order */ #define SEEQCFG2_AUTO_REA (0x0002) /* if set, Receive End Area will be updated when reading from Buffer */ #define SEEQCFG2_CRC_ERR_EN (0x0008) /* enables receiving of packets with CRC errors */ #define SEEQCFG2_DRIBBLE_EN (0x0010) /* enables receiving of non-aligned packets */ #define SEEQCFG2_SHORT_EN (0x0020) /* enables receiving of short packets */ #define SEEQCFG2_SLOTSEL (0x0040) /* 0= standard IEEE802.3, 1= smaller,faster, non-standard */ #define SEEQCFG2_NO_PREAM (0x0080) /* 1= user supplies Xmit preamble bytes */ #define SEEQCFG2_ADDR_LEN (0x0100) /* 1= 2byte addresses */ #define SEEQCFG2_REC_CRC (0x0200) /* 0= received packets will have CRC stripped from them */ #define SEEQCFG2_XMIT_NO_CRC (0x0400) /* don't xmit CRC with each packet (user supplies it) */ #define SEEQCFG2_LOOPBACK (0x0800) #define SEEQCFG2_CTRLO (0x1000) #define SEEQCFG2_RESET (0x8000) /* software Hard-reset bit */ struct seeq_pkt_hdr { unsigned short next; /* address of next packet header */ unsigned char babble_int:1, /* enable int on >1514 byte packet */ coll_int:1, /* enable int on collision */ coll_16_int:1, /* enable int on >15 collision */ xmit_int:1, /* enable int on success (or xmit with <15 collision) */ unused:1, data_follows:1, /* if not set, process this as a header and pointer only */ chain_cont:1, /* if set, more headers in chain only cmd bit valid in recv header */ xmit_recv:1; /* if set, a xmit packet, else a receive packet.*/ unsigned char status; }; #define SEEQPKTH_BAB_INT_EN (0x01) /* xmit only */ #define SEEQPKTH_COL_INT_EN (0x02) /* xmit only */ #define SEEQPKTH_COL16_INT_EN (0x04) /* xmit only */ #define SEEQPKTH_XMIT_INT_EN (0x08) /* xmit only */ #define SEEQPKTH_DATA_FOLLOWS (0x20) /* supposedly in xmit only */ #define SEEQPKTH_CHAIN (0x40) /* more headers follow */ #define SEEQPKTH_XMIT (0x80) #define SEEQPKTS_BABBLE (0x0100) /* xmit only */ #define SEEQPKTS_OVERSIZE (0x0100) /* recv only */ #define SEEQPKTS_COLLISION (0x0200) /* xmit only */ #define SEEQPKTS_CRC_ERR (0x0200) /* recv only */ #define SEEQPKTS_COLL16 (0x0400) /* xmit only */ #define SEEQPKTS_DRIB (0x0400) /* recv only */ #define SEEQPKTS_SHORT (0x0800) /* recv only */ #define SEEQPKTS_DONE (0x8000) #define SEEQPKTS_ANY_ERROR (0x0f00)