config HERMES tristate "Hermes chipset 802.11b support (Orinoco/Prism2/Symbol)" depends on (PPC_PMAC || PCI || PCMCIA) depends on CFG80211 select CFG80211_WEXT select WIRELESS_EXT select WEXT_SPY select WEXT_PRIV select FW_LOADER select CRYPTO select CRYPTO_MICHAEL_MIC ---help--- A driver for 802.11b wireless cards based on the "Hermes" or Intersil HFA384x (Prism 2) MAC controller. This includes the vast majority of the PCMCIA 802.11b cards (which are nearly all rebadges) - except for the Cisco/Aironet cards. Cards supported include the Apple Airport (not a PCMCIA card), WavelanIEEE/Orinoco, Cabletron/EnteraSys Roamabout, ELSA AirLancer, MELCO Buffalo, Avaya, IBM High Rate Wireless, Farralon Syyline, Samsung MagicLAN, Netgear MA401, LinkSys WPC-11, D-Link DWL-650, 3Com AirConnect, Intel IPW2011, and Symbol Spectrum24 High Rate amongst others. This option includes the guts of the driver, but in order to actually use a card you will also need to enable support for PCMCIA Hermes cards, PLX9052 based PCI adaptors or the Apple Airport below. You will also very likely also need the Wireless Tools in order to configure your card and that /etc/pcmcia/wireless.opts works : config HERMES_PRISM bool "Support Prism 2/2.5 chipset" depends on HERMES ---help--- Say Y to enable support for Prism 2 and 2.5 chipsets. These chipsets are better handled by the hostap driver. This driver would not support WPA or firmware download for Prism chipset. If you are not sure, say N. config HERMES_CACHE_FW_ON_INIT bool "Cache Hermes firmware on driver initialisation" depends on HERMES default y ---help--- Say Y to cache any firmware required by the Hermes drivers on startup. The firmware will remain cached until the driver is unloaded. The cache uses 64K of RAM. Otherwise load the firmware from userspace as required. In this case the driver should be unloaded and restarted whenever the firmware is changed. If you are not sure, say Y. config APPLE_AIRPORT tristate "Apple Airport support (built-in)" depends on PPC_PMAC && HERMES help Say Y here to support the Airport 802.11b wireless Ethernet hardware built into the Macintosh iBook and other recent PowerPC-based Macintosh machines. This is essentially a Lucent Orinoco card with a non-standard interface. This driver does not support the Airport Extreme (802.11b/g). Use the BCM43xx driver for Airport Extreme cards. config PLX_HERMES tristate "Hermes in PLX9052 based PCI adaptor support (Netgear MA301 etc.)" depends on PCI && HERMES help Enable support for PCMCIA cards supported by the "Hermes" (aka orinoco) driver when used in PLX9052 based PCI adaptors. These adaptors are not a full PCMCIA controller but act as a more limited PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that 802.11b PCMCIA cards can be used in desktop machines. The Netgear MA301 is such an adaptor. config TMD_HERMES tristate "Hermes in TMD7160 based PCI adaptor support" depends on PCI && HERMES help Enable support for PCMCIA cards supported by the "Hermes" (aka orinoco) driver when used in TMD7160 based PCI adaptors. These adaptors are not a full PCMCIA controller but act as a more limited PCI <-> PCMCIA bridge. Several vendors sell such adaptors so that 802.11b PCMCIA cards can be used in desktop machines. config NORTEL_HERMES tristate "Nortel emobility PCI adaptor support" depends on PCI && HERMES help Enable support for PCMCIA cards supported by the "Hermes" (aka orinoco) driver when used in Nortel emobility PCI adaptors. These adaptors are not full PCMCIA controllers, but act as a more limited PCI <-> PCMCIA bridge. config PCI_HERMES tristate "Prism 2.5 PCI 802.11b adaptor support" depends on PCI && HERMES && HERMES_PRISM help Enable support for PCI and mini-PCI 802.11b wireless NICs based on the Prism 2.5 chipset. These are true PCI cards, not the 802.11b PCMCIA cards bundled with PCI<->PCMCIA adaptors which are also common. Some of the built-in wireless adaptors in laptops are of this variety. config PCMCIA_HERMES tristate "Hermes PCMCIA card support" depends on PCMCIA && HERMES && HAS_IOPORT_MAP ---help--- A driver for "Hermes" chipset based PCMCIA wireless adaptors, such as the Lucent WavelanIEEE/Orinoco cards and their OEM (Cabletron/ EnteraSys RoamAbout 802.11, ELSA Airlancer, Melco Buffalo and others). It should also be usable on various Prism II based cards such as the Linksys, D-Link and Farallon Skyline. It should also work on Symbol cards such as the 3Com AirConnect and Ericsson WLAN. You will very likely need the Wireless Tools in order to configure your card and that /etc/pcmcia/wireless.opts works: . config PCMCIA_SPECTRUM tristate "Symbol Spectrum24 Trilogy PCMCIA card support" depends on PCMCIA && HERMES && HAS_IOPORT_MAP ---help--- This is a driver for 802.11b cards using RAM-loadable Symbol firmware, such as Symbol Wireless Networker LA4100, CompactFlash cards by Socket Communications and Intel PRO/Wireless 2011B. This driver requires firmware download on startup. Utilities for downloading Symbol firmware are available at config ORINOCO_USB tristate "Agere Orinoco USB support" depends on USB && HERMES select FW_LOADER ---help--- This driver is for USB versions of the Agere Orinoco card.