/* * Safe Encapsulated USB Serial Driver * * Copyright (C) 2001 Lineo * Copyright (C) 2001 Hewlett-Packard * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * By: * Stuart Lynne , Tom Rushworth */ /* * The encapsultaion is designed to overcome difficulties with some USB hardware. * * While the USB protocol has a CRC over the data while in transit, i.e. while * being carried over the bus, there is no end to end protection. If the hardware * has any problems getting the data into or out of the USB transmit and receive * FIFO's then data can be lost. * * This protocol adds a two byte trailer to each USB packet to specify the number * of bytes of valid data and a 10 bit CRC that will allow the receiver to verify * that the entire USB packet was received without error. * * Because in this case the sender and receiver are the class and function drivers * there is now end to end protection. * * There is an additional option that can be used to force all transmitted packets * to be padded to the maximum packet size. This provides a work around for some * devices which have problems with small USB packets. * * Assuming a packetsize of N: * * 0..N-2 data and optional padding * * N-2 bits 7-2 - number of bytes of valid data * bits 1-0 top two bits of 10 bit CRC * N-1 bottom 8 bits of 10 bit CRC * * * | Data Length | 10 bit CRC | * + 7 . 6 . 5 . 4 . 3 . 2 . 1 . 0 | 7 . 6 . 5 . 4 . 3 . 2 . 1 . 0 + * * The 10 bit CRC is computed across the sent data, followed by the trailer with * the length set and the CRC set to zero. The CRC is then OR'd into the trailer. * * When received a 10 bit CRC is computed over the entire frame including the trailer * and should be equal to zero. * * Two module parameters are used to control the encapsulation, if both are * turned of the module works as a simple serial device with NO * encapsulation. * * See linux/drivers/usbd/serial_fd for a device function driver * implementation of this. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include "usb-serial.h" #ifndef CONFIG_USB_SAFE_PADDED #define CONFIG_USB_SAFE_PADDED 0 #endif static int debug; static int safe = 1; static int padded = CONFIG_USB_SAFE_PADDED; #define DRIVER_VERSION "v0.0b" #define DRIVER_AUTHOR "sl@lineo.com, tbr@lineo.com" #define DRIVER_DESC "USB Safe Encapsulated Serial" MODULE_AUTHOR (DRIVER_AUTHOR); MODULE_DESCRIPTION (DRIVER_DESC); MODULE_LICENSE("GPL"); #if defined(CONFIG_USBD_SAFE_SERIAL_VENDOR) && !defined(CONFIG_USBD_SAFE_SERIAL_PRODUCT) #abort "SAFE_SERIAL_VENDOR defined without SAFE_SERIAL_PRODUCT" #endif #if ! defined(CONFIG_USBD_SAFE_SERIAL_VENDOR) static __u16 vendor; // no default static __u16 product; // no default module_param(vendor, ushort, 0); MODULE_PARM_DESC(vendor, "User specified USB idVendor (required)"); module_param(product, ushort, 0); MODULE_PARM_DESC(product, "User specified USB idProduct (required)"); #endif module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); module_param(safe, bool, 0); MODULE_PARM_DESC(safe, "Turn Safe Encapsulation On/Off"); module_param(padded, bool, 0); MODULE_PARM_DESC(padded, "Pad to full wMaxPacketSize On/Off"); #define CDC_DEVICE_CLASS 0x02 #define CDC_INTERFACE_CLASS 0x02 #define CDC_INTERFACE_SUBCLASS 0x06 #define LINEO_INTERFACE_CLASS 0xff #define LINEO_INTERFACE_SUBCLASS_SAFENET 0x01 #define LINEO_SAFENET_CRC 0x01 #define LINEO_SAFENET_CRC_PADDED 0x02 #define LINEO_INTERFACE_SUBCLASS_SAFESERIAL 0x02 #define LINEO_SAFESERIAL_CRC 0x01 #define LINEO_SAFESERIAL_CRC_PADDED 0x02 #define MY_USB_DEVICE(vend,prod,dc,ic,isc) \ .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_DEV_CLASS | \ USB_DEVICE_ID_MATCH_INT_CLASS | USB_DEVICE_ID_MATCH_INT_SUBCLASS, \ .idVendor = (vend), \ .idProduct = (prod),\ .bDeviceClass = (dc),\ .bInterfaceClass = (ic), \ .bInterfaceSubClass = (isc), static struct usb_device_id id_table[] = { {MY_USB_DEVICE (0x49f, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Itsy {MY_USB_DEVICE (0x3f0, 0x2101, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Calypso {MY_USB_DEVICE (0x4dd, 0x8001, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Iris {MY_USB_DEVICE (0x4dd, 0x8002, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie {MY_USB_DEVICE (0x4dd, 0x8003, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie {MY_USB_DEVICE (0x4dd, 0x8004, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Collie {MY_USB_DEVICE (0x5f9, 0xffff, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, // Sharp tmp #if defined(CONFIG_USB_SAFE_SERIAL_VENDOR) {MY_USB_DEVICE (CONFIG_USB_SAFE_SERIAL_VENDOR, CONFIG_USB_SAFE_SERIAL_PRODUCT, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, #endif // extra null entry for module // vendor/produc parameters {MY_USB_DEVICE (0, 0, CDC_DEVICE_CLASS, LINEO_INTERFACE_CLASS, LINEO_INTERFACE_SUBCLASS_SAFESERIAL)}, {} // terminating entry }; MODULE_DEVICE_TABLE (usb, id_table); static struct usb_driver safe_driver = { .owner = THIS_MODULE, .name = "safe_serial", .probe = usb_serial_probe, .disconnect = usb_serial_disconnect, .id_table = id_table, }; static __u16 crc10_table[256] = { 0x000, 0x233, 0x255, 0x066, 0x299, 0x0aa, 0x0cc, 0x2ff, 0x301, 0x132, 0x154, 0x367, 0x198, 0x3ab, 0x3cd, 0x1fe, 0x031, 0x202, 0x264, 0x057, 0x2a8, 0x09b, 0x0fd, 0x2ce, 0x330, 0x103, 0x165, 0x356, 0x1a9, 0x39a, 0x3fc, 0x1cf, 0x062, 0x251, 0x237, 0x004, 0x2fb, 0x0c8, 0x0ae, 0x29d, 0x363, 0x150, 0x136, 0x305, 0x1fa, 0x3c9, 0x3af, 0x19c, 0x053, 0x260, 0x206, 0x035, 0x2ca, 0x0f9, 0x09f, 0x2ac, 0x352, 0x161, 0x107, 0x334, 0x1cb, 0x3f8, 0x39e, 0x1ad, 0x0c4, 0x2f7, 0x291, 0x0a2, 0x25d, 0x06e, 0x008, 0x23b, 0x3c5, 0x1f6, 0x190, 0x3a3, 0x15c, 0x36f, 0x309, 0x13a, 0x0f5, 0x2c6, 0x2a0, 0x093, 0x26c, 0x05f, 0x039, 0x20a, 0x3f4, 0x1c7, 0x1a1, 0x392, 0x16d, 0x35e, 0x338, 0x10b, 0x0a6, 0x295, 0x2f3, 0x0c0, 0x23f, 0x00c, 0x06a, 0x259, 0x3a7, 0x194, 0x1f2, 0x3c1, 0x13e, 0x30d, 0x36b, 0x158, 0x097, 0x2a4, 0x2c2, 0x0f1, 0x20e, 0x03d, 0x05b, 0x268, 0x396, 0x1a5, 0x1c3, 0x3f0, 0x10f, 0x33c, 0x35a, 0x169, 0x188, 0x3bb, 0x3dd, 0x1ee, 0x311, 0x122, 0x144, 0x377, 0x289, 0x0ba, 0x0dc, 0x2ef, 0x010, 0x223, 0x245, 0x076, 0x1b9, 0x38a, 0x3ec, 0x1df, 0x320, 0x113, 0x175, 0x346, 0x2b8, 0x08b, 0x0ed, 0x2de, 0x021, 0x212, 0x274, 0x047, 0x1ea, 0x3d9, 0x3bf, 0x18c, 0x373, 0x140, 0x126, 0x315, 0x2eb, 0x0d8, 0x0be, 0x28d, 0x072, 0x241, 0x227, 0x014, 0x1db, 0x3e8, 0x38e, 0x1bd, 0x342, 0x171, 0x117, 0x324, 0x2da, 0x0e9, 0x08f, 0x2bc, 0x043, 0x270, 0x216, 0x025, 0x14c, 0x37f, 0x319, 0x12a, 0x3d5, 0x1e6, 0x180, 0x3b3, 0x24d, 0x07e, 0x018, 0x22b, 0x0d4, 0x2e7, 0x281, 0x0b2, 0x17d, 0x34e, 0x328, 0x11b, 0x3e4, 0x1d7, 0x1b1, 0x382, 0x27c, 0x04f, 0x029, 0x21a, 0x0e5, 0x2d6, 0x2b0, 0x083, 0x12e, 0x31d, 0x37b, 0x148, 0x3b7, 0x184, 0x1e2, 0x3d1, 0x22f, 0x01c, 0x07a, 0x249, 0x0b6, 0x285, 0x2e3, 0x0d0, 0x11f, 0x32c, 0x34a, 0x179, 0x386, 0x1b5, 0x1d3, 0x3e0, 0x21e, 0x02d, 0x04b, 0x278, 0x087, 0x2b4, 0x2d2, 0x0e1, }; #define CRC10_INITFCS 0x000 // Initial FCS value #define CRC10_GOODFCS 0x000 // Good final FCS value #define CRC10_FCS(fcs, c) ( (((fcs) << 8) & 0x3ff) ^ crc10_table[((fcs) >> 2) & 0xff] ^ (c)) /** * fcs_compute10 - memcpy and calculate 10 bit CRC across buffer * @sp: pointer to buffer * @len: number of bytes * @fcs: starting FCS * * Perform a memcpy and calculate fcs using ppp 10bit CRC algorithm. Return * new 10 bit FCS. */ static __u16 __inline__ fcs_compute10 (unsigned char *sp, int len, __u16 fcs) { for (; len-- > 0; fcs = CRC10_FCS (fcs, *sp++)); return fcs; } static void safe_read_bulk_callback (struct urb *urb, struct pt_regs *regs) { struct usb_serial_port *port = (struct usb_serial_port *) urb->context; unsigned char *data = urb->transfer_buffer; unsigned char length = urb->actual_length; int i; int result; dbg ("%s", __FUNCTION__); if (urb->status) { dbg ("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); return; } dbg ("safe_read_bulk_callback length: %d", port->read_urb->actual_length); #ifdef ECHO_RCV { int i; unsigned char *cp = port->read_urb->transfer_buffer; for (i = 0; i < port->read_urb->actual_length; i++) { if ((i % 32) == 0) { printk ("\nru[%02x] ", i); } printk ("%02x ", *cp++); } printk ("\n"); } #endif if (safe) { __u16 fcs; if (!(fcs = fcs_compute10 (data, length, CRC10_INITFCS))) { int actual_length = data[length - 2] >> 2; if (actual_length <= (length - 2)) { info ("%s - actual: %d", __FUNCTION__, actual_length); for (i = 0; i < actual_length; i++) { tty_insert_flip_char (port->tty, data[i], 0); } tty_flip_buffer_push (port->tty); } else { err ("%s - inconsistent lengths %d:%d", __FUNCTION__, actual_length, length); } } else { err ("%s - bad CRC %x", __FUNCTION__, fcs); } } else { for (i = 0; i < length; i++) { tty_insert_flip_char (port->tty, data[i], 0); } tty_flip_buffer_push (port->tty); } /* Continue trying to always read */ usb_fill_bulk_urb (urb, port->serial->dev, usb_rcvbulkpipe (port->serial->dev, port->bulk_in_endpointAddress), urb->transfer_buffer, urb->transfer_buffer_length, safe_read_bulk_callback, port); if ((result = usb_submit_urb (urb, GFP_ATOMIC))) { err ("%s - failed resubmitting read urb, error %d", __FUNCTION__, result); } } static int safe_write (struct usb_serial_port *port, const unsigned char *buf, int count) { unsigned char *data; int result; int i; int packet_length; dbg ("safe_write port: %p %d urb: %p count: %d", port, port->number, port->write_urb, count); if (!port->write_urb) { dbg ("%s - write urb NULL", __FUNCTION__); return (0); } dbg ("safe_write write_urb: %d transfer_buffer_length", port->write_urb->transfer_buffer_length); if (!port->write_urb->transfer_buffer_length) { dbg ("%s - write urb transfer_buffer_length zero", __FUNCTION__); return (0); } if (count == 0) { dbg ("%s - write request of 0 bytes", __FUNCTION__); return (0); } spin_lock(&port->lock); if (port->write_urb_busy) { spin_unlock(&port->lock); dbg("%s - already writing", __FUNCTION__); return 0; } port->write_urb_busy = 1; spin_unlock(&port->lock); packet_length = port->bulk_out_size; // get max packetsize i = packet_length - (safe ? 2 : 0); // get bytes to send count = (count > i) ? i : count; // get the data into the transfer buffer data = port->write_urb->transfer_buffer; memset (data, '0', packet_length); memcpy (data, buf, count); if (safe) { __u16 fcs; // pad if necessary if (!padded) { packet_length = count + 2; } // set count data[packet_length - 2] = count << 2; data[packet_length - 1] = 0; // compute fcs and insert into trailer fcs = fcs_compute10 (data, packet_length, CRC10_INITFCS); data[packet_length - 2] |= fcs >> 8; data[packet_length - 1] |= fcs & 0xff; // set length to send port->write_urb->transfer_buffer_length = packet_length; } else { port->write_urb->transfer_buffer_length = count; } usb_serial_debug_data(debug, &port->dev, __FUNCTION__, count, port->write_urb->transfer_buffer); #ifdef ECHO_TX { int i; unsigned char *cp = port->write_urb->transfer_buffer; for (i = 0; i < port->write_urb->transfer_buffer_length; i++) { if ((i % 32) == 0) { printk ("\nsu[%02x] ", i); } printk ("%02x ", *cp++); } printk ("\n"); } #endif port->write_urb->dev = port->serial->dev; if ((result = usb_submit_urb (port->write_urb, GFP_KERNEL))) { port->write_urb_busy = 0; err ("%s - failed submitting write urb, error %d", __FUNCTION__, result); return 0; } dbg ("%s urb: %p submitted", __FUNCTION__, port->write_urb); return (count); } static int safe_write_room (struct usb_serial_port *port) { int room = 0; // Default: no room dbg ("%s", __FUNCTION__); if (port->write_urb_busy) room = port->bulk_out_size - (safe ? 2 : 0); if (room) { dbg ("safe_write_room returns %d", room); } return (room); } static int safe_startup (struct usb_serial *serial) { switch (serial->interface->cur_altsetting->desc.bInterfaceProtocol) { case LINEO_SAFESERIAL_CRC: break; case LINEO_SAFESERIAL_CRC_PADDED: padded = 1; break; default: return -EINVAL; } return 0; } static struct usb_serial_device_type safe_device = { .owner = THIS_MODULE, .name = "Safe", .id_table = id_table, .num_interrupt_in = NUM_DONT_CARE, .num_bulk_in = NUM_DONT_CARE, .num_bulk_out = NUM_DONT_CARE, .num_ports = 1, .write = safe_write, .write_room = safe_write_room, .read_bulk_callback = safe_read_bulk_callback, .attach = safe_startup, }; static int __init safe_init (void) { int i, retval; info (DRIVER_VERSION " " DRIVER_AUTHOR); info (DRIVER_DESC); info ("vendor: %x product: %x safe: %d padded: %d\n", vendor, product, safe, padded); // if we have vendor / product parameters patch them into id list if (vendor || product) { info ("vendor: %x product: %x\n", vendor, product); for (i = 0; i < (sizeof (id_table) / sizeof (struct usb_device_id)); i++) { if (!id_table[i].idVendor && !id_table[i].idProduct) { id_table[i].idVendor = vendor; id_table[i].idProduct = product; break; } } } retval = usb_serial_register(&safe_device); if (retval) goto failed_usb_serial_register; retval = usb_register(&safe_driver); if (retval) goto failed_usb_register; return 0; failed_usb_register: usb_serial_deregister(&safe_device); failed_usb_serial_register: return retval; } static void __exit safe_exit (void) { usb_deregister (&safe_driver); usb_serial_deregister (&safe_device); } module_init (safe_init); module_exit (safe_exit);