aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
blob: 46a135dae6b369519d0c7614d7f3391983f65132 (plain) (blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
STMicroelectronics STi MIPHY28LP PHY binding
============================================

This binding describes a miphy device that is used to control PHY hardware
for SATA, PCIe or USB3.

Required properties (controller (parent) node):
- compatible	: Should be "st,miphy28lp-phy".
- st,syscfg	: Should be a phandle of the system configuration register group
		  which contain the SATA, PCIe or USB3 mode setting bits.

Required nodes	:  A sub-node is required for each channel the controller
		   provides. Address range information including the usual
		   'reg' and 'reg-names' properties are used inside these
		   nodes to describe the controller's topology. These nodes
		   are translated by the driver's .xlate() function.

Required properties (port (child) node):
- #phy-cells	: Should be 1 (See second example)
		  Cell after port phandle is device type from:
			- PHY_TYPE_SATA
			- PHY_TYPE_PCI
			- PHY_TYPE_USB3
- reg		: Address and length of the register set for the device.
- reg-names	: The names of the register addresses corresponding to the registers
		  filled in "reg". It can also contain the offset of the system configuration
		  registers used as glue-logic to setup the device for SATA/PCIe or USB3
		  devices.
- resets	: phandle to the parent reset controller.
- reset-names	: Associated name must be "miphy-sw-rst".

Optional properties (port (child) node):
- st,osc-rdy		: to check the MIPHY0_OSC_RDY status in the glue-logic. This
			  is not available in all the MiPHY. For example, for STiH407, only the
			  MiPHY0 has this bit.
- st,osc-force-ext	: to select the external oscillator. This can change from
			  different MiPHY inside the same SoC.
- st,sata_gen		: to select which SATA_SPDMODE has to be set in the SATA system config
			  register.
- st,px_rx_pol_inv	: to invert polarity of RXn/RXp (respectively negative line and positive
			  line).
- st,scc-on		: enable ssc to reduce effects of EMI (only for sata or PCIe).
- st,tx-impedance-comp	: to compensate tx impedance avoiding out of range values.

example:

		miphy28lp_phy: miphy28lp@9b22000 {
			compatible = "st,miphy28lp-phy";
			st,syscfg = <&syscfg_core>;
			#address-cells	= <1>;
			#size-cells	= <1>;
			ranges;

			phy_port0: port@9b22000 {
				reg = <0x9b22000 0xff>,
				      <0x9b09000 0xff>,
				      <0x9b04000 0xff>,
				      <0x114 0x4>, /* sysctrl MiPHY cntrl */
				      <0x818 0x4>, /* sysctrl MiPHY status*/
				      <0xe0  0x4>, /* sysctrl PCIe */
				      <0xec  0x4>; /* sysctrl SATA */
				reg-names = "sata-up",
					    "pcie-up",
					    "pipew",
					    "miphy-ctrl-glue",
					    "miphy-status-glue",
					    "pcie-glue",
					    "sata-glue";
				#phy-cells = <1>;
				st,osc-rdy;
				reset-names = "miphy-sw-rst";
				resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
			};

			phy_port1: port@9b2a000 {
				reg = <0x9b2a000 0xff>,
				      <0x9b19000 0xff>,
				      <0x9b14000 0xff>,
				      <0x118 0x4>,
				      <0x81c 0x4>,
				      <0xe4  0x4>,
				      <0xf0  0x4>;
				reg-names = "sata-up",
					    "pcie-up",
					    "pipew",
					    "miphy-ctrl-glue",
					    "miphy-status-glue",
					    "pcie-glue",
					    "sata-glue";
				#phy-cells = <1>;
				st,osc-force-ext;
				reset-names = "miphy-sw-rst";
				resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
			};

			phy_port2: port@8f95000 {
				reg = <0x8f95000 0xff>,
				      <0x8f90000 0xff>,
				      <0x11c 0x4>,
				      <0x820 0x4>;
				reg-names = "pipew",
				    "usb3-up",
				    "miphy-ctrl-glue",
				    "miphy-status-glue";
				#phy-cells = <1>;
				reset-names = "miphy-sw-rst";
				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
			};
		};


Specifying phy control of devices
=================================

Device nodes should specify the configuration required in their "phys"
property, containing a phandle to the miphy device node and an index
specifying which configuration to use, as described in phy-bindings.txt.

example:
		sata0: sata@9b20000  {
			...
			phys		= <&phy_port0 PHY_TYPE_SATA>;
			...
		};

Macro definitions for the supported miphy configuration can be found in:

include/dt-bindings/phy/phy-miphy28lp.h