| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Moved PTP pointer validation before its use to avoid smatch warning.
Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree.
Fixes: 2ef4e45d99b1 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In legacy silicon, promiscuous mode is only modified
through CGX mbox messages. In CN10KB silicon, it is modified
from CGX mbox and NIX. This breaks legacy application
behaviour. Fix this by removing call from NIX.
Fixes: d6c9784baf59 ("octeontx2-af: Invoke exact match functions if supported")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current duplex mode was unset in the driver, resulting in the default
parameter being set to 0, which corresponds to half duplex. It might
mislead users to have incorrect expectation about the driver's
transmission capabilities.
Set the default duplex configuration to full, as the driver runs in
full duplex mode at this point.
Fixes: 7e074d5a76ca ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the event of a failure in tcf_change_indev(), fw_set_parms() will
immediately return an error after incrementing or decrementing
reference counter in tcf_bind_filter(). If attacker can control
reference counter to zero and make reference freed, leading to
use after free.
In order to prevent this, move the point of possible failure above the
point where the TC_FW_CLASSID is handled.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: M A Ramdhan <ramdhan@starlabs.sg>
Signed-off-by: M A Ramdhan <ramdhan@starlabs.sg>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Pedro Tammela <pctammela@mojatatu.com>
Message-ID: <20230705161530.52003-1-ramdhan@starlabs.sg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For some cases as below, we may encounter the unpreditable chip stats
in driver probe()
* The system reboot flow do not work properly, such as kernel oops while
rebooting, and then the driver do not go back to default status at
this moment.
* Similar to the flow above. If the device was enabled in BIOS or UEFI,
the system may switch to Linux without driver fully shutdown.
To avoid the problem, force push the device back to default in probe()
* mt7921e_mcu_fw_pmctrl() : return control privilege to chip side.
* mt7921_wfsys_reset() : cleanup chip config before resource init.
Error log
[59007.600714] mt7921e 0000:02:00.0: ASIC revision: 79220010
[59010.889773] mt7921e 0000:02:00.0: Message 00000010 (seq 1) timeout
[59010.889786] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59014.217839] mt7921e 0000:02:00.0: Message 00000010 (seq 2) timeout
[59014.217852] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59017.545880] mt7921e 0000:02:00.0: Message 00000010 (seq 3) timeout
[59017.545893] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59020.874086] mt7921e 0000:02:00.0: Message 00000010 (seq 4) timeout
[59020.874099] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59024.202019] mt7921e 0000:02:00.0: Message 00000010 (seq 5) timeout
[59024.202033] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59027.530082] mt7921e 0000:02:00.0: Message 00000010 (seq 6) timeout
[59027.530096] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59030.857888] mt7921e 0000:02:00.0: Message 00000010 (seq 7) timeout
[59030.857904] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59034.185946] mt7921e 0000:02:00.0: Message 00000010 (seq 8) timeout
[59034.185961] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59037.514249] mt7921e 0000:02:00.0: Message 00000010 (seq 9) timeout
[59037.514262] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.842362] mt7921e 0000:02:00.0: Message 00000010 (seq 10) timeout
[59040.842375] mt7921e 0000:02:00.0: Failed to get patch semaphore
[59040.923845] mt7921e 0000:02:00.0: hardware init failed
Cc: stable@vger.kernel.org
Fixes: 5c14a5f944b9 ("mt76: mt7921: introduce mt7921e support")
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Juan Martinez <juan.martinez@amd.com>
Co-developed-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Message-ID: <39fcb7cee08d4ab940d38d82f21897483212483f.1688569385.git.deren.wu@mediatek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This switch implements Hold/Release in a strange way, with no control
from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC
and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly
based on the schedule.
Namely, when the gate of a preemptible TC is about to close (actually
QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event),
the QSYS seems to emit a HOLD request pulse towards the MAC which
preempts the currently transmitted packet, and further packets are held
back in the queue system.
This allows large frames to be squeezed through small time slots,
because HOLD requests initiated by the gate events result in the frame
being segmented in multiple fragments, the bit time of which is equal to
the size of the time slot.
It has been reported that the vsc9959_tas_guard_bands_update() logic
breaks this, because it doesn't take preemptible TCs into account, and
enables oversized frame dropping when the time slot doesn't allow a full
MTU to be sent, but it does allow 2*minFragSize to be sent (128B).
Packets larger than 128B are dropped instead of being sent in multiple
fragments.
Confusingly, the manual says:
| For guard band, SDU calculation of a traffic class of a port, if
| preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then
| QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise
| QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used.
but this only refers to the static guard band durations, and the
QMAXSDU_CFG_* registers have dual purpose - the other being oversized
frame dropping, which takes place irrespective of whether frames are
preemptible or express.
So, to fix the problem, we need to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and modify the guard
band logic to consider a different (lower) oversize limit for
preemptible traffic classes.
Fixes: 403ffc2c34de ("net: mscc: ocelot: add support for preemptible traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a future change we will need to make
ocelot_port_update_active_preemptible_tcs() call
vsc9959_tas_guard_bands_update(), but that is currently not possible,
since the ocelot switch lib does not have access to functions private to
the DSA wrapper.
Move the pointer to vsc9959_tas_guard_bands_update() from felix->info
(which is private to the DSA driver) to ocelot->ops (which is also
visible to the ocelot switch lib).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-3-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef987e ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we boot with mvneta.txq_number=1, the txq_map is set incorrectly:
MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is
initialized. Fix this.
Fixes: 50bf8cb6fc9c ("net: mvneta: Configure XPS support")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When evaluating byteorder expressions with size 2, a union with 32-bit and
16-bit members is used. Since the 16-bit members are aligned to 32-bit,
the array accesses will be out-of-bounds.
It may lead to a stack-out-of-bounds access like the one below:
[ 23.095215] ==================================================================
[ 23.095625] BUG: KASAN: stack-out-of-bounds in nft_byteorder_eval+0x13c/0x320
[ 23.096020] Read of size 2 at addr ffffc90000007948 by task ping/115
[ 23.096358]
[ 23.096456] CPU: 0 PID: 115 Comm: ping Not tainted 6.4.0+ #413
[ 23.096770] Call Trace:
[ 23.096910] <IRQ>
[ 23.097030] dump_stack_lvl+0x60/0xc0
[ 23.097218] print_report+0xcf/0x630
[ 23.097388] ? nft_byteorder_eval+0x13c/0x320
[ 23.097577] ? kasan_addr_to_slab+0xd/0xc0
[ 23.097760] ? nft_byteorder_eval+0x13c/0x320
[ 23.097949] kasan_report+0xc9/0x110
[ 23.098106] ? nft_byteorder_eval+0x13c/0x320
[ 23.098298] __asan_load2+0x83/0xd0
[ 23.098453] nft_byteorder_eval+0x13c/0x320
[ 23.098659] nft_do_chain+0x1c8/0xc50
[ 23.098852] ? __pfx_nft_do_chain+0x10/0x10
[ 23.099078] ? __kasan_check_read+0x11/0x20
[ 23.099295] ? __pfx___lock_acquire+0x10/0x10
[ 23.099535] ? __pfx___lock_acquire+0x10/0x10
[ 23.099745] ? __kasan_check_read+0x11/0x20
[ 23.099929] nft_do_chain_ipv4+0xfe/0x140
[ 23.100105] ? __pfx_nft_do_chain_ipv4+0x10/0x10
[ 23.100327] ? lock_release+0x204/0x400
[ 23.100515] ? nf_hook.constprop.0+0x340/0x550
[ 23.100779] nf_hook_slow+0x6c/0x100
[ 23.100977] ? __pfx_nft_do_chain_ipv4+0x10/0x10
[ 23.101223] nf_hook.constprop.0+0x334/0x550
[ 23.101443] ? __pfx_ip_local_deliver_finish+0x10/0x10
[ 23.101677] ? __pfx_nf_hook.constprop.0+0x10/0x10
[ 23.101882] ? __pfx_ip_rcv_finish+0x10/0x10
[ 23.102071] ? __pfx_ip_local_deliver_finish+0x10/0x10
[ 23.102291] ? rcu_read_lock_held+0x4b/0x70
[ 23.102481] ip_local_deliver+0xbb/0x110
[ 23.102665] ? __pfx_ip_rcv+0x10/0x10
[ 23.102839] ip_rcv+0x199/0x2a0
[ 23.102980] ? __pfx_ip_rcv+0x10/0x10
[ 23.103140] __netif_receive_skb_one_core+0x13e/0x150
[ 23.103362] ? __pfx___netif_receive_skb_one_core+0x10/0x10
[ 23.103647] ? mark_held_locks+0x48/0xa0
[ 23.103819] ? process_backlog+0x36c/0x380
[ 23.103999] __netif_receive_skb+0x23/0xc0
[ 23.104179] process_backlog+0x91/0x380
[ 23.104350] __napi_poll.constprop.0+0x66/0x360
[ 23.104589] ? net_rx_action+0x1cb/0x610
[ 23.104811] net_rx_action+0x33e/0x610
[ 23.105024] ? _raw_spin_unlock+0x23/0x50
[ 23.105257] ? __pfx_net_rx_action+0x10/0x10
[ 23.105485] ? mark_held_locks+0x48/0xa0
[ 23.105741] __do_softirq+0xfa/0x5ab
[ 23.105956] ? __dev_queue_xmit+0x765/0x1c00
[ 23.106193] do_softirq.part.0+0x49/0xc0
[ 23.106423] </IRQ>
[ 23.106547] <TASK>
[ 23.106670] __local_bh_enable_ip+0xf5/0x120
[ 23.106903] __dev_queue_xmit+0x789/0x1c00
[ 23.107131] ? __pfx___dev_queue_xmit+0x10/0x10
[ 23.107381] ? find_held_lock+0x8e/0xb0
[ 23.107585] ? lock_release+0x204/0x400
[ 23.107798] ? neigh_resolve_output+0x185/0x350
[ 23.108049] ? mark_held_locks+0x48/0xa0
[ 23.108265] ? neigh_resolve_output+0x185/0x350
[ 23.108514] neigh_resolve_output+0x246/0x350
[ 23.108753] ? neigh_resolve_output+0x246/0x350
[ 23.109003] ip_finish_output2+0x3c3/0x10b0
[ 23.109250] ? __pfx_ip_finish_output2+0x10/0x10
[ 23.109510] ? __pfx_nf_hook+0x10/0x10
[ 23.109732] __ip_finish_output+0x217/0x390
[ 23.109978] ip_finish_output+0x2f/0x130
[ 23.110207] ip_output+0xc9/0x170
[ 23.110404] ip_push_pending_frames+0x1a0/0x240
[ 23.110652] raw_sendmsg+0x102e/0x19e0
[ 23.110871] ? __pfx_raw_sendmsg+0x10/0x10
[ 23.111093] ? lock_release+0x204/0x400
[ 23.111304] ? __mod_lruvec_page_state+0x148/0x330
[ 23.111567] ? find_held_lock+0x8e/0xb0
[ 23.111777] ? find_held_lock+0x8e/0xb0
[ 23.111993] ? __rcu_read_unlock+0x7c/0x2f0
[ 23.112225] ? aa_sk_perm+0x18a/0x550
[ 23.112431] ? filemap_map_pages+0x4f1/0x900
[ 23.112665] ? __pfx_aa_sk_perm+0x10/0x10
[ 23.112880] ? find_held_lock+0x8e/0xb0
[ 23.113098] inet_sendmsg+0xa0/0xb0
[ 23.113297] ? inet_sendmsg+0xa0/0xb0
[ 23.113500] ? __pfx_inet_sendmsg+0x10/0x10
[ 23.113727] sock_sendmsg+0xf4/0x100
[ 23.113924] ? move_addr_to_kernel.part.0+0x4f/0xa0
[ 23.114190] __sys_sendto+0x1d4/0x290
[ 23.114391] ? __pfx___sys_sendto+0x10/0x10
[ 23.114621] ? __pfx_mark_lock.part.0+0x10/0x10
[ 23.114869] ? lock_release+0x204/0x400
[ 23.115076] ? find_held_lock+0x8e/0xb0
[ 23.115287] ? rcu_is_watching+0x23/0x60
[ 23.115503] ? __rseq_handle_notify_resume+0x6e2/0x860
[ 23.115778] ? __kasan_check_write+0x14/0x30
[ 23.116008] ? blkcg_maybe_throttle_current+0x8d/0x770
[ 23.116285] ? mark_held_locks+0x28/0xa0
[ 23.116503] ? do_syscall_64+0x37/0x90
[ 23.116713] __x64_sys_sendto+0x7f/0xb0
[ 23.116924] do_syscall_64+0x59/0x90
[ 23.117123] ? irqentry_exit_to_user_mode+0x25/0x30
[ 23.117387] ? irqentry_exit+0x77/0xb0
[ 23.117593] ? exc_page_fault+0x92/0x140
[ 23.117806] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 23.118081] RIP: 0033:0x7f744aee2bba
[ 23.118282] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
[ 23.119237] RSP: 002b:00007ffd04a7c9f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[ 23.119644] RAX: ffffffffffffffda RBX: 00007ffd04a7e0a0 RCX: 00007f744aee2bba
[ 23.120023] RDX: 0000000000000040 RSI: 000056488e9e6300 RDI: 0000000000000003
[ 23.120413] RBP: 000056488e9e6300 R08: 00007ffd04a80320 R09: 0000000000000010
[ 23.120809] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[ 23.121219] R13: 00007ffd04a7dc38 R14: 00007ffd04a7ca00 R15: 00007ffd04a7e0a0
[ 23.121617] </TASK>
[ 23.121749]
[ 23.121845] The buggy address belongs to the virtual mapping at
[ 23.121845] [ffffc90000000000, ffffc90000009000) created by:
[ 23.121845] irq_init_percpu_irqstack+0x1cf/0x270
[ 23.122707]
[ 23.122803] The buggy address belongs to the physical page:
[ 23.123104] page:0000000072ac19f0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x24a09
[ 23.123609] flags: 0xfffffc0001000(reserved|node=0|zone=1|lastcpupid=0x1fffff)
[ 23.123998] page_type: 0xffffffff()
[ 23.124194] raw: 000fffffc0001000 ffffea0000928248 ffffea0000928248 0000000000000000
[ 23.124610] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 23.125023] page dumped because: kasan: bad access detected
[ 23.125326]
[ 23.125421] Memory state around the buggy address:
[ 23.125682] ffffc90000007800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 23.126072] ffffc90000007880: 00 00 00 00 00 f1 f1 f1 f1 f1 f1 00 00 f2 f2 00
[ 23.126455] >ffffc90000007900: 00 00 00 00 00 00 00 00 00 f2 f2 f2 f2 00 00 00
[ 23.126840] ^
[ 23.127138] ffffc90000007980: 00 00 00 00 00 00 00 00 00 00 00 00 00 f3 f3 f3
[ 23.127522] ffffc90000007a00: f3 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
[ 23.127906] ==================================================================
[ 23.128324] Disabling lock debugging due to kernel taint
Using simple s16 pointers for the 16-bit accesses fixes the problem. For
the 32-bit accesses, src and dst can be used directly.
Fixes: 96518518cc41 ("netfilter: add nftables")
Cc: stable@vger.kernel.org
Reported-by: Tanguy DUBROCA (@SidewayRE) from @Synacktiv working with ZDI
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.
There were issues reported where PPS is not generated when
start time is in past.
Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"
In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.
Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"
Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.
In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.
1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.
This patch takes care of calculating and programming
appropriate future time value into Target Time registers.
Fixes: 5e91c72e560c ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
IEEE 802.1Q does not have clear definitions of what constitutes an
SDU (Service Data Unit), but IEEE Std 802.3 clause 3.1.2 does define
the MAC service primitives and clause 3.2.7 does define the MAC Client
Data for Q-tagged frames.
It shows that the mac_service_data_unit (MSDU) does NOT contain the
preamble, destination and source address, or FCS. The MSDU does contain
the length/type field, MAC client data, VLAN tag and any padding
data (prior to the FCS).
Thus, the maximum 802.3 frame size that is allowed to be transmitted
should be QueueMaxSDU (MSDU) + 16 (6 byte SA + 6 byte DA + 4 byte FCS).
Fixes: 92a0dcb8427d ("igc: offload queue max SDU from tc-taprio")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
set TP bit in the 'supported' and 'advertising' fields. i225/226 parts
only support twisted pair copper.
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Prasad Koya <prasad@arista.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port.
Fixes: e20aa071cd95 ("nfp: fix schedule in atomic context when sync mc address")
Cc: stable@vger.kernel.org
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Message-ID: <20230705052818.7122-1-louis.peens@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently mlx5e releases pages directly to the page_pool for XDP_TX and
does page fragment counting for XDP_REDIRECT. RX pages from the
page_pool are leaking on XDP_REDIRECT because the xdp core will release
only one fragment out of MLX5E_PAGECNT_BIAS_MAX and subsequently the page
is marked as "skip release" which avoids the driver release.
A fix would be to take an extra fragment for XDP_REDIRECT and not set the
"skip release" bit so that the release on the driver side can handle the
remaining bias fragments. But this would be a shortsighted solution.
Instead, this patch converges the two XDP paths (XDP_TX and XDP_REDIRECT) to
always do fragment tracking. The "skip release" bit is no longer
necessary for XDP.
Fixes: 6f5742846053 ("net/mlx5e: RX, Enable skb page recycling through the page_pool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
On vport enable, where fw's hca caps are queried, the driver queries
hca_caps_2 without checking if fw truly supports them, causing a false
failure of vfs vport load and blocking SRIOV enablement on old devices
such as CX4 where hca_caps_2 support is missing.
Thus, add a check for the said caps support before accessing them.
Fixes: e5b9642a33be ("net/mlx5: E-Switch, Implement devlink port function cmds to control migratable")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Non-clear CT action causes a flow rule split, while CT clear action
doesn't and is just a header-rewrite to the current flow rule.
But ct offload is done in post_parse and is per ct action instance,
so ct clear offload is parsed multiple times, while its deleted once.
Fix this by post_parsing the ct action only once per flow attribute
(which is per flow rule) by using a offloaded ct_attr flag.
Fixes: 08fe94ec5f77 ("net/mlx5e: TC, Remove special handling of CT action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently the check for NOT_READY flag is performed before obtaining the
necessary lock. This opens a possibility for race condition when the flow
is concurrently removed from unready_flows list by the workqueue task,
which causes a double-removal from the list and a crash[0]. Fix the issue
by moving the flag check inside the section protected by
uplink_priv->unready_flows_lock mutex.
[0]:
[44376.389654] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP
[44376.391665] CPU: 7 PID: 59123 Comm: tc Not tainted 6.4.0-rc4+ #1
[44376.392984] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[44376.395342] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.396857] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.399167] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.399680] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.400337] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.401001] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.401663] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.402342] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.402999] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.403787] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.404343] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.405004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.405665] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[44376.406339] Call Trace:
[44376.406651] <TASK>
[44376.406939] ? die_addr+0x33/0x90
[44376.407311] ? exc_general_protection+0x192/0x390
[44376.407795] ? asm_exc_general_protection+0x22/0x30
[44376.408292] ? mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.408876] __mlx5e_tc_del_fdb_peer_flow+0xbc/0xe0 [mlx5_core]
[44376.409482] mlx5e_tc_del_flow+0x42/0x210 [mlx5_core]
[44376.410055] mlx5e_flow_put+0x25/0x50 [mlx5_core]
[44376.410529] mlx5e_delete_flower+0x24b/0x350 [mlx5_core]
[44376.411043] tc_setup_cb_reoffload+0x22/0x80
[44376.411462] fl_reoffload+0x261/0x2f0 [cls_flower]
[44376.411907] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.412481] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.413044] tcf_block_playback_offloads+0x76/0x170
[44376.413497] tcf_block_unbind+0x7b/0xd0
[44376.413881] tcf_block_setup+0x17d/0x1c0
[44376.414269] tcf_block_offload_cmd.isra.0+0xf1/0x130
[44376.414725] tcf_block_offload_unbind+0x43/0x70
[44376.415153] __tcf_block_put+0x82/0x150
[44376.415532] ingress_destroy+0x22/0x30 [sch_ingress]
[44376.415986] qdisc_destroy+0x3b/0xd0
[44376.416343] qdisc_graft+0x4d0/0x620
[44376.416706] tc_get_qdisc+0x1c9/0x3b0
[44376.417074] rtnetlink_rcv_msg+0x29c/0x390
[44376.419978] ? rep_movs_alternative+0x3a/0xa0
[44376.420399] ? rtnl_calcit.isra.0+0x120/0x120
[44376.420813] netlink_rcv_skb+0x54/0x100
[44376.421192] netlink_unicast+0x1f6/0x2c0
[44376.421573] netlink_sendmsg+0x232/0x4a0
[44376.421980] sock_sendmsg+0x38/0x60
[44376.422328] ____sys_sendmsg+0x1d0/0x1e0
[44376.422709] ? copy_msghdr_from_user+0x6d/0xa0
[44376.423127] ___sys_sendmsg+0x80/0xc0
[44376.423495] ? ___sys_recvmsg+0x8b/0xc0
[44376.423869] __sys_sendmsg+0x51/0x90
[44376.424226] do_syscall_64+0x3d/0x90
[44376.424587] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[44376.425046] RIP: 0033:0x7f045134f887
[44376.425403] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
[44376.426914] RSP: 002b:00007ffd63a82b98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[44376.427592] RAX: ffffffffffffffda RBX: 000000006481955f RCX: 00007f045134f887
[44376.428195] RDX: 0000000000000000 RSI: 00007ffd63a82c00 RDI: 0000000000000003
[44376.428796] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[44376.429404] R10: 00007f0451208708 R11: 0000000000000246 R12: 0000000000000001
[44376.430039] R13: 0000000000409980 R14: 000000000047e538 R15: 0000000000485400
[44376.430644] </TASK>
[44376.430907] Modules linked in: mlx5_ib mlx5_core act_mirred act_tunnel_key cls_flower vxlan dummy sch_ingress openvswitch nsh rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_g
ss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc fuse [last unloaded: mlx5_core]
[44376.433936] ---[ end trace 0000000000000000 ]---
[44376.434373] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.434951] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.436452] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.436924] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.437530] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.438179] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.438786] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.439393] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.439998] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.440714] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.441225] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.441843] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.442471] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fixes: ad86755b18d5 ("net/mlx5e: Protect unready flows with dedicated lock")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prior to this patch only one "mlx5" thermal zone could have been
registered regardless of the number of individual mlx5 devices in the
system.
To fix this setup a unique name per device to register its own thermal
zone.
In order to not register a thermal zone for a virtual device (VF/SF) add
a check for PF device type.
The new name is a concatenation between "mlx5_" and "<PCI_DEV_BDF>", which
will also help associating a thermal zone with its PCI device.
$ lspci | grep ConnectX
00:04.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx]
00:05.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx]
$ cat /sys/devices/virtual/thermal/thermal_zone0/type
mlx5_0000:00:04.0
$ cat /sys/devices/virtual/thermal/thermal_zone1/type
mlx5_0000:00:05.0
Fixes: c1fef618d611 ("net/mlx5: Implement thermal zone")
CC: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Regular (non-XSK) RQs get flushed on XSK setup and re-activated on XSK
close. If the same regular RQ is closed (a config change for example)
soon after the XSK close, a double release occurs because the missing
wqes get released a second time.
Fixes: 3f93f82988bc ("net/mlx5e: RX, Defer page release in legacy rq for better recycling")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When kvzalloc_node or kvzalloc failed in mlx5e_ptp_open, the memory
pointed by "c" or "cparams" is not freed, which can lead to a memory
leak. Fix by freeing the array in the error path.
Fixes: 145e5637d941 ("net/mlx5e: Add TX PTP port object support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The memory pointed to by the fs->any pointer is not freed in the error
path of mlx5e_fs_tt_redirect_any_create, which can lead to a memory leak.
Fix by freeing the memory in the error path, thereby making the error path
identical to mlx5e_fs_tt_redirect_any_destroy().
Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In function accel_fs_tcp_create_groups(), when the ft->g memory is
successfully allocated but the 'in' memory fails to be allocated, the
memory pointed to by ft->g is released once. And in function
accel_fs_tcp_create_table, mlx5e_destroy_flow_table is called to release
the memory pointed to by ft->g again. This will cause double free problem.
Fixes: c062d52ac24c ("net/mlx5e: Receive flow steering framework for accelerated TCP flows")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
If a user schedules a Gate Control List (GCL) to close one of
the QBV gates while also transmitting a packet to that closed gate,
TX Hang will be happen. HW would not drop any packet when the gate
is closed and keep queuing up in HW TX FIFO until the gate is re-opened.
This patch implements the solution to drop the packet for the closed
gate.
This patch will also reset the adapter to perform SW initialization
for each 1st Gate Control List (GCL) to avoid hang.
This is due to the HW design, where changing to TSN transmit mode
requires SW initialization. Intel Discrete I225/6 transmit mode
cannot be changed when in dynamic mode according to Software User
Manual Section 7.5.2.1. Subsequent Gate Control List (GCL) operations
will proceed without a reset, as they already are in TSN Mode.
Step to reproduce:
DUT:
1) Configure GCL List with certain gate close.
BASE=$(date +%s%N)
tc qdisc replace dev $IFACE parent root handle 100 taprio \
num_tc 4 \
map 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE \
sched-entry S 0x8 500000 \
sched-entry S 0x4 500000 \
flags 0x2
2) Transmit the packet to closed gate. You may use udp_tai
application to transmit UDP packet to any of the closed gate.
./udp_tai -i <interface> -P 100000 -p 90 -c 1 -t <0/1> -u 30004
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading")
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Tested-by: Chwee Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.
Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.
It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add condition to increase the qbv counter during taprio qbv
configuration only.
There might be a case when TC already been setup then user configure
the ETF/CBS qdisc and this counter will increase if no condition above.
Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
I added a warning about about GUP no longer expanding the stack in
commit a425ac5365f6 ("gup: add warning if some caller would seem to want
stack expansion"), but didn't really expect anybody to hit it.
And it's true that nobody seems to have hit a _real_ case yet, but we
certainly have a number of reports of false positives. Which not only
causes extra noise in itself, but might also end up hiding any real
cases if they do exist.
So let's tighten up the warning condition, and replace the simplistic
vma = find_vma(mm, start);
if (vma && (start < vma->vm_start)) {
WARN_ON_ONCE(vma->vm_flags & VM_GROWSDOWN);
with a
vma = gup_vma_lookup(mm, start);
helper function which works otherwise like just "vma_lookup()", but with
some heuristics for when to warn about gup no longer causing stack
expansion.
In particular, don't just warn for "below the stack", but warn if it's
_just_ below the stack (with "just below" arbitrarily defined as 64kB,
because why not?). And rate-limit it to at most once per hour, which
means that any false positives shouldn't completely hide subsequent
reports, but we won't be flooding the logs about it either.
The previous code triggered when some GUP user (chromium crashpad)
accessing past the end of the previous vma, for example. That has never
expanded the stack, it just causes GUP to return early, and as such we
shouldn't be warning about it.
This is still going trigger the randomized testers, but to mitigate the
noise from that, use "dump_stack()" instead of "WARN_ON_ONCE()" to get
the kernel call chain. We'll get the relevant information, but syzbot
shouldn't get too upset about it.
Also, don't even bother with the GROWSUP case, which would be using
different heuristics entirely, but only happens on parisc.
Reported-by: kernel test robot <oliver.sang@intel.com>
Reported-by: John Hubbard <jhubbard@nvidia.com>
Reported-by: syzbot+6cf44e127903fdf9d929@syzkaller.appspotmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Configuring tx_maxrate via sysfs interface
/sys/class/net/eth0/queues/tx-1/tx_maxrate was not working when
TCs are configured because always main VSI was being used. Fix by
using correct VSI in ice_set_tx_maxrate when TCs are configured.
Fixes: 1ddef455f4a8 ("ice: Add NDO callback to set the maximum per-queue bitrate")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove incorrect check in ice_validate_mqprio_opt() that limits
filter configuration when sum of max_rates of all TCs exceeds
the link speed. The max rate of each TC is unrelated to value
used by other TCs and is valid as long as it is less than link
speed.
Fixes: fbc7b27af0f9 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Replace my email.
Cc: devicetree@vger.kernel.org
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230703092026.4923-1-quic_mkshah@quicinc.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The DTS code coding style expects spaces around '=' sign.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #display/msm
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20230702182308.7583-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
When adding a rule to a chain referring to its ID, if that chain had been
deleted on the same batch, the rule might end up referring to a deleted
chain.
This will lead to a WARNING like following:
[ 33.098431] ------------[ cut here ]------------
[ 33.098678] WARNING: CPU: 5 PID: 69 at net/netfilter/nf_tables_api.c:2037 nf_tables_chain_destroy+0x23d/0x260
[ 33.099217] Modules linked in:
[ 33.099388] CPU: 5 PID: 69 Comm: kworker/5:1 Not tainted 6.4.0+ #409
[ 33.099726] Workqueue: events nf_tables_trans_destroy_work
[ 33.100018] RIP: 0010:nf_tables_chain_destroy+0x23d/0x260
[ 33.100306] Code: 8b 7c 24 68 e8 64 9c ed fe 4c 89 e7 e8 5c 9c ed fe 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7 c3 cc cc cc cc <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 89 c6 89 c7
[ 33.101271] RSP: 0018:ffffc900004ffc48 EFLAGS: 00010202
[ 33.101546] RAX: 0000000000000001 RBX: ffff888006fc0a28 RCX: 0000000000000000
[ 33.101920] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 33.102649] RBP: ffffc900004ffc78 R08: 0000000000000000 R09: 0000000000000000
[ 33.103018] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8880135ef500
[ 33.103385] R13: 0000000000000000 R14: dead000000000122 R15: ffff888006fc0a10
[ 33.103762] FS: 0000000000000000(0000) GS:ffff888024c80000(0000) knlGS:0000000000000000
[ 33.104184] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 33.104493] CR2: 00007fe863b56a50 CR3: 00000000124b0001 CR4: 0000000000770ee0
[ 33.104872] PKRU: 55555554
[ 33.104999] Call Trace:
[ 33.105113] <TASK>
[ 33.105214] ? show_regs+0x72/0x90
[ 33.105371] ? __warn+0xa5/0x210
[ 33.105520] ? nf_tables_chain_destroy+0x23d/0x260
[ 33.105732] ? report_bug+0x1f2/0x200
[ 33.105902] ? handle_bug+0x46/0x90
[ 33.106546] ? exc_invalid_op+0x19/0x50
[ 33.106762] ? asm_exc_invalid_op+0x1b/0x20
[ 33.106995] ? nf_tables_chain_destroy+0x23d/0x260
[ 33.107249] ? nf_tables_chain_destroy+0x30/0x260
[ 33.107506] nf_tables_trans_destroy_work+0x669/0x680
[ 33.107782] ? mark_held_locks+0x28/0xa0
[ 33.107996] ? __pfx_nf_tables_trans_destroy_work+0x10/0x10
[ 33.108294] ? _raw_spin_unlock_irq+0x28/0x70
[ 33.108538] process_one_work+0x68c/0xb70
[ 33.108755] ? lock_acquire+0x17f/0x420
[ 33.108977] ? __pfx_process_one_work+0x10/0x10
[ 33.109218] ? do_raw_spin_lock+0x128/0x1d0
[ 33.109435] ? _raw_spin_lock_irq+0x71/0x80
[ 33.109634] worker_thread+0x2bd/0x700
[ 33.109817] ? __pfx_worker_thread+0x10/0x10
[ 33.110254] kthread+0x18b/0x1d0
[ 33.110410] ? __pfx_kthread+0x10/0x10
[ 33.110581] ret_from_fork+0x29/0x50
[ 33.110757] </TASK>
[ 33.110866] irq event stamp: 1651
[ 33.111017] hardirqs last enabled at (1659): [<ffffffffa206a209>] __up_console_sem+0x79/0xa0
[ 33.111379] hardirqs last disabled at (1666): [<ffffffffa206a1ee>] __up_console_sem+0x5e/0xa0
[ 33.111740] softirqs last enabled at (1616): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0
[ 33.112094] softirqs last disabled at (1367): [<ffffffffa1f5d40e>] __irq_exit_rcu+0x9e/0xe0
[ 33.112453] ---[ end trace 0000000000000000 ]---
This is due to the nft_chain_lookup_byid ignoring the genmask. After this
change, adding the new rule will fail as it will not find the chain.
Fixes: 837830a4b439 ("netfilter: nf_tables: add NFTA_RULE_CHAIN_ID attribute")
Cc: stable@vger.kernel.org
Reported-by: Mingi Cho of Theori working with ZDI
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Originally this used jhash2() over tuple and folded the zone id,
the pernet hash value, destination port and l4 protocol number into the
32bit seed value.
When the switch to siphash was done, I used an on-stack temporary
buffer to build a suitable key to be hashed via siphash().
But this showed up as performance regression, so I got rid of
the temporary copy and collected to-be-hashed data in 4 u64 variables.
This makes it easy to build tuples that produce the same hash, which isn't
desirable even though chain lengths are limited.
Switch back to plain siphash, but just like with jhash2(), take advantage
of the fact that most of to-be-hashed data is already in a suitable order.
Use an empty struct as annotation in 'struct nf_conntrack_tuple' to mark
last member that can be used as hash input.
The only remaining data that isn't present in the tuple structure are the
zone identifier and the pernet hash: fold those into the key.
Fixes: d2c806abcf0b ("netfilter: conntrack: use siphash_4u64")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If nf_conntrack_init_start() fails (for example due to a
register_nf_conntrack_bpf() failure), the nf_conntrack_helper_fini()
clean-up path frees the nf_ct_helper_hash map.
When built with NF_CONNTRACK=y, further netfilter modules (e.g:
netfilter_conntrack_ftp) can still be loaded and call
nf_conntrack_helpers_register(), independently of whether nf_conntrack
initialized correctly. This accesses the nf_ct_helper_hash dangling
pointer and causes a uaf, possibly leading to random memory corruption.
This patch guards nf_conntrack_helper_register() from accessing a freed
or uninitialized nf_ct_helper_hash pointer and fixes possible
uses-after-free when loading a conntrack module.
Cc: stable@vger.kernel.org
Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Florent Revest <revest@chromium.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Now that conntrack core is allowd to insert clashing entries, make sure
GRE won't set assured flag on NAT_CLASH entries, just like UDP.
Doing so prevents early_drop logic for these entries.
Fixes: d671fd82eaa9 ("netfilter: conntrack: allow insertion clash of gre protocol")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Overflow use refcount checks are not complete.
Add helper function to deal with object reference counter tracking.
Report -EMFILE in case UINT_MAX is reached.
nft_use_dec() splats in case that reference counter underflows,
which should not ever happen.
Add nft_use_inc_restore() and nft_use_dec_restore() which are used
to restore reference counter from error and abort paths.
Use u32 in nft_flowtable and nft_object since helper functions cannot
work on bitfields.
Remove the few early incomplete checks now that the helper functions
are in place and used to check for refcount overflow.
Fixes: 96518518cc41 ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When using pm_nl_ctl to validate userspace path-manager's behaviours, it
was failing on 32-bit architectures ~half of the time.
pm_nl_ctl was not reporting any error but the command was not doing what
it was expected to do. As a result, the expected linked event was not
triggered after and the test failed.
This is due to the fact the token given in argument to the application
was parsed as an integer with atoi(): in a 32-bit arch, if the number
was bigger than INT_MAX, 2147483647 was used instead.
This can simply be fixed by using strtoul() instead of atoi().
The errors have been seen "by chance" when manually looking at the
results from LKFT.
Fixes: 9a0b36509df0 ("selftests: mptcp: support MPTCP_PM_CMD_ANNOUNCE")
Cc: stable@vger.kernel.org
Fixes: ecd2a77d672f ("selftests: mptcp: support MPTCP_PM_CMD_REMOVE")
Fixes: cf8d0a6dfd64 ("selftests: mptcp: support MPTCP_PM_CMD_SUBFLOW_CREATE")
Fixes: 57cc361b8d38 ("selftests: mptcp: support MPTCP_PM_CMD_SUBFLOW_DESTROY")
Fixes: ca188a25d43f ("selftests: mptcp: userspace PM support for MP_PRIO signals")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPTCP selftests are using TCP SYN Cookies for quite a while now, since
v5.9.
Some CIs don't have this config option enabled and this is causing
issues in the tests:
# ns1 MPTCP -> ns1 (10.0.1.1:10000 ) MPTCP (duration 167ms) sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory
# [ OK ]./mptcp_connect.sh: line 554: [: -eq: unary operator expected
There is no impact in the results but the test is not doing what it is
supposed to do.
Fixes: fed61c4b584c ("selftests: mptcp: make 2nd net namespace use tcp syn cookies unconditionally")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A message was mentioning an issue with the "remove" tests but the
selftest was not marked as failed.
Directly exit with an error like it is done everywhere else in this
selftest.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 259a834fadda ("selftests: mptcp: functional tests for the userspace PM type")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"server4_port" variable is not set but "app4_port" is the server port in
v4 and the correct variable name to use.
The port is optional so there was no visible impact.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: ca188a25d43f ("selftests: mptcp: userspace PM support for MP_PRIO signals")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an error was detected when checking the marks, a message was
correctly printed mentioning the error but followed by another one
saying everything was OK and the selftest was not marked as failed as
expected.
Now the 'ret' variable is directly set to 1 in order to make sure the
exit is done with an error, similar to what is done in other functions.
While at it, the error is correctly propagated to the caller.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: dc65fe82fb07 ("selftests: mptcp: add packet mark test case")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPTables commands using 'iptables-nft' fail on old kernels, at least
on v5.15 because it doesn't see the default IPTables chains:
$ iptables -L
iptables/1.8.2 Failed to initialize nft: Protocol not supported
As a first step before switching to NFTables, we can use iptables-legacy
if available.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: dc65fe82fb07 ("selftests: mptcp: add packet mark test case")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of "external" errors when preparing the environment for the
TProxy tests, the subtests were marked as skipped.
This is fine but it means these errors are ignored. On MPTCP Public CI,
we do want to catch such issues and mark the selftest as failed if there
are such issues. We can then use mptcp_lib_fail_if_expected_feature()
helper that has been recently added to fail if needed.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 5fb62e9cd3ad ("selftests: mptcp: add tproxy test case")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the blamed commit, closing the first subflow resets the first
subflow socket state to SS_UNCONNECTED.
The current mptcp listen implementation relies only on such
state to prevent touching not-fully-disconnected sockets.
Incoming mptcp fastclose (or paired endpoint removal) unconditionally
closes the first subflow.
All the above allows an incoming fastclose followed by a listen() call
to successfully race with a blocking recvmsg(), potentially causing the
latter to hit a divide by zero bug in cleanup_rbuf/__tcp_select_window().
Address the issue explicitly checking the msk socket state in
mptcp_listen(). An alternative solution would be moving the first
subflow socket state update into mptcp_disconnect(), but in the long
term the first subflow socket should be removed: better avoid relaying
on it for internal consistency check.
Fixes: b29fcfb54cd7 ("mptcp: full disconnect implementation")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/414
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While tacking care of the mptcp-level listener I unintentionally
moved the subflow level unhash after the subflow listener backlog
cleanup.
That could cause some nasty race and makes the code harder to read.
Address the issue restoring the proper order of operations.
Fixes: 57fc0f1ceaa4 ("mptcp: ensure listener is unhashed before updating the sk status")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change boolean parameter of function "qeth_l3_vipa_store" inside the
"qeth_l3_dev_vipa_del4_store" function from "true" to "false" because
"true" is used for adding a virtual ip address and "false" for deleting.
Fixes: 2390166a6b45 ("s390/qeth: clean up L3 sysfs code")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 534066a983df0935847061c844eb178f8a53a9e7.
It's actively detrimental in that it hides files that shouldn't be
hidden.
If I have some b4 mbx file in my git directory, it either was already
applied with "git am" and is now stale, or maybe it's waiting for that
to happen. In neither case is "ignore it" the right option.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When an AFS FS.StoreData RPC call is made, amongst other things it is
given the resultant file size to be. On the server, this is processed
by truncating the file to new size and then writing the data.
Now, kafs has a lock (vnode->io_lock) that serves to serialise
operations against a specific vnode (ie. inode), but the parameters for
the op are set before the lock is taken. This allows two writebacks
(say sync and kswapd) to race - and if writes are ongoing the writeback
for a later write could occur before the writeback for an earlier one if
the latter gets interrupted.
Note that afs_writepages() cannot take i_mutex and only takes a shared
lock on vnode->validate_lock.
Also note that the server does the truncation and the write inside a
lock, so there's no problem at that end.
Fix this by moving the calculation for the proposed new i_size inside
the vnode->io_lock. Also reset the iterator (which we might have read
from) and update the mtime setting there.
Fixes: bd80d8a80e12 ("afs: Use ITER_XARRAY for writing")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/3526895.1687960024@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MAC block on CN10K (RPM) supports hardware timestamp configuration. The
previous patch which added timestamp configuration support has a bug.
Though the netdev driver requests to disable timestamp configuration,
the driver is always enabling it.
This patch fixes the same.
Fixes: d1489208681d ("octeontx2-af: cn10k: RPM hardware timestamp configuration")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
incl_srcpt has the limitation, mentioned in commit b4638af8885a ("net:
dsa: sja1105: always enable the INCL_SRCPT option"), that frames with a
MAC DA of 01:80:c2:xx:yy:zz will be received as 01:80:c2:00:00:zz unless
PTP RX timestamping is enabled.
The incl_srcpt option was initially unconditionally enabled, then that
changed with commit 42824463d38d ("net: dsa: sja1105: Limit use of
incl_srcpt to bridge+vlan mode"), then again with b4638af8885a ("net:
dsa: sja1105: always enable the INCL_SRCPT option"). Bottom line is that
it now needs to be always enabled, otherwise the driver does not have a
reliable source of information regarding source_port and switch_id for
link-local traffic (tag_8021q VLANs may be imprecise since now they
identify an entire bridging domain when ports are not standalone).
If we accept that PTP RX timestamping (and therefore, meta frame
generation) is always enabled in hardware, then that limitation could be
avoided and packets with any MAC DA can be properly received, because
meta frames do contain the original bytes from the MAC DA of their
associated link-local packet.
This change enables meta frame generation unconditionally, which also
has the nice side effects of simplifying the switch control path
(a switch reset is no longer required on hwtstamping settings change)
and the tagger data path (it no longer needs to be informed whether to
expect meta frames or not - it always does).
Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Sai Krishna
Ratheesh Kannoth
Junfeng Guo
M A Ramdhan
Quan Zhou
Vladimir Oltean
Klaus Kudielka
Thadeu Lima de Souza Cascardo
Aravindhan Gunasekaran
Tan Tee Min
Prasad Koya
Yinjun Zhang
Dragos Tatulea
Maher Sanalla
Yevgeny Kliteynik
Vlad Buslov
Saeed Mahameed
Zhengchao Shao
Muhammad Husaini Zulkifli
Linus Torvalds
Sridhar Samudrala
Maulik Shah
Krzysztof Kozlowski
Florian Westphal
Florent Revest
Pablo Neira Ayuso
Matthieu Baerts
Paolo Abeni
Thorsten Winkler
David Howells
Hariprasad Kelam