| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We need to use selinux_cred() to fetch the SELinux cred blob instead
of directly using current->security or current_security(). There
were a couple of lingering uses of current_security() in the SELinux code
that were apparently missed during the earlier conversions. IIUC, this
would only manifest as a bug if multiple security modules including
SELinux are enabled and SELinux is not first in the lsm order. After
this change, there appear to be no other users of current_security()
in-tree; perhaps we should remove it altogether.
Fixes: bbd3662a8348 ("Infrastructure management of the cred security blob")
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
As noted in Documentation/atomic_t.txt, if we don't need the RMW atomic
operations, we should only use READ_ONCE()/WRITE_ONCE() +
smp_rmb()/smp_wmb() where necessary (or the combined variants
smp_load_acquire()/smp_store_release()).
This patch converts the sidtab code to use regular u32 for the counter
and reverse lookup cache and use the appropriate operations instead of
atomic_get()/atomic_set(). Note that when reading/updating the reverse
lookup cache we don't need memory barriers as it doesn't need to be
consistent or accurate. We can now also replace some atomic ops with
regular loads (when under spinlock) and stores (for conversion target
fields that are always accessed under the master table's spinlock).
We can now also bump SIDTAB_MAX to U32_MAX as we can use the full u32
range again.
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
As of now, setting watches on filesystem objects has, at most, applied a
check for read access to the inode, and in the case of fanotify, requires
CAP_SYS_ADMIN. No specific security hook or permission check has been
provided to control the setting of watches. Using any of inotify, dnotify,
or fanotify, it is possible to observe, not only write-like operations, but
even read access to a file. Modeling the watch as being merely a read from
the file is insufficient for the needs of SELinux. This is due to the fact
that read access should not necessarily imply access to information about
when another process reads from a file. Furthermore, fanotify watches grant
more power to an application in the form of permission events. While
notification events are solely, unidirectional (i.e. they only pass
information to the receiving application), permission events are blocking.
Permission events make a request to the receiving application which will
then reply with a decision as to whether or not that action may be
completed. This causes the issue of the watching application having the
ability to exercise control over the triggering process. Without drawing a
distinction within the permission check, the ability to read would imply
the greater ability to control an application. Additionally, mount and
superblock watches apply to all files within the same mount or superblock.
Read access to one file should not necessarily imply the ability to watch
all files accessed within a given mount or superblock.
In order to solve these issues, a new LSM hook is implemented and has been
placed within the system calls for marking filesystem objects with inotify,
fanotify, and dnotify watches. These calls to the hook are placed at the
point at which the target path has been resolved and are provided with the
path struct, the mask of requested notification events, and the type of
object on which the mark is being set (inode, superblock, or mount). The
mask and obj_type have already been translated into common FS_* values
shared by the entirety of the fs notification infrastructure. The path
struct is passed rather than just the inode so that the mount is available,
particularly for mount watches. This also allows for use of the hook by
pathname-based security modules. However, since the hook is intended for
use even by inode based security modules, it is not placed under the
CONFIG_SECURITY_PATH conditional. Otherwise, the inode-based security
modules would need to enable all of the path hooks, even though they do not
use any of them.
This only provides a hook at the point of setting a watch, and presumes
that permission to set a particular watch implies the ability to receive
all notification about that object which match the mask. This is all that
is required for SELinux. If other security modules require additional hooks
or infrastructure to control delivery of notification, these can be added
by them. It does not make sense for us to propose hooks for which we have
no implementation. The understanding that all notifications received by the
requesting application are all strictly of a type for which the application
has been granted permission shows that this implementation is sufficient in
its coverage.
Security modules wishing to provide complete control over fanotify must
also implement a security_file_open hook that validates that the access
requested by the watching application is authorized. Fanotify has the issue
that it returns a file descriptor with the file mode specified during
fanotify_init() to the watching process on event. This is already covered
by the LSM security_file_open hook if the security module implements
checking of the requested file mode there. Otherwise, a watching process
can obtain escalated access to a file for which it has not been authorized.
The selinux_path_notify hook implementation works by adding five new file
permissions: watch, watch_mount, watch_sb, watch_reads, and watch_with_perm
(descriptions about which will follow), and one new filesystem permission:
watch (which is applied to superblock checks). The hook then decides which
subset of these permissions must be held by the requesting application
based on the contents of the provided mask and the obj_type. The
selinux_file_open hook already checks the requested file mode and therefore
ensures that a watching process cannot escalate its access through
fanotify.
The watch, watch_mount, and watch_sb permissions are the baseline
permissions for setting a watch on an object and each are a requirement for
any watch to be set on a file, mount, or superblock respectively. It should
be noted that having either of the other two permissions (watch_reads and
watch_with_perm) does not imply the watch, watch_mount, or watch_sb
permission. Superblock watches further require the filesystem watch
permission to the superblock. As there is no labeled object in view for
mounts, there is no specific check for mount watches beyond watch_mount to
the inode. Such a check could be added in the future, if a suitable labeled
object existed representing the mount.
The watch_reads permission is required to receive notifications from
read-exclusive events on filesystem objects. These events include accessing
a file for the purpose of reading and closing a file which has been opened
read-only. This distinction has been drawn in order to provide a direct
indication in the policy for this otherwise not obvious capability. Read
access to a file should not necessarily imply the ability to observe read
events on a file.
Finally, watch_with_perm only applies to fanotify masks since it is the
only way to set a mask which allows for the blocking, permission event.
This permission is needed for any watch which is of this type. Though
fanotify requires CAP_SYS_ADMIN, this is insufficient as it gives implicit
trust to root, which we do not do, and does not support least privilege.
Signed-off-by: Aaron Goidel <acgoide@tycho.nsa.gov>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Previously if we couldn't find an entry in the cache and we failed to
allocate memory for a new cache entry we would fail the network object
label lookup; this is obviously not ideal. This patch fixes this so
that we return the object label even if we can't cache the object at
this point in time due to memory pressure.
The GitHub issue tracker is below:
* https://github.com/SELinuxProject/selinux-kernel/issues/3
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The name is overly long and inconsistent with the other *_val_to_struct
members. Dropping the "_array" prefix makes the code easier to read and
gets rid of one line over 80 characters warning.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Fix most of the code style warnings discovered when moving code around.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
No code changes, but move a lot of the policydb destructors higher up
so we can get rid of a forward declaration.
This patch does expose a few old checkpatch.pl errors, but those will
be dealt with in a separate (set of) patches.
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Since roles_init() adds some entries to the role hash table, we need to
destroy also its keys/values on error, otherwise we get a memory leak in
the error path.
Cc: <stable@vger.kernel.org>
Reported-by: syzbot+fee3a14d4cdf92646287@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
We need to error out when trying to add an entry above SIDTAB_MAX in
sidtab_reverse_lookup() to avoid overflow on the odd chance that this
happens.
Cc: stable@vger.kernel.org
Fixes: ee1a84fdfeed ("selinux: overhaul sidtab to fix bug and improve performance")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The userspace tools expect all fields of the same name to be logged
consistently with the same encoding. Since the invalid_context fields
contain untrusted strings in selinux_inode_setxattr()
and selinux_setprocattr(), encode all instances of this field the same
way as though they were untrusted even though
compute_sid_handle_invalid_context() and security_sid_mls_copy() are
trusted.
Please see github issue
https://github.com/linux-audit/audit-kernel/issues/57
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
When sid == 0 (we are resetting keycreate_sid to the default value), we
should skip the KEY__CREATE check.
Before this patch, doing a zero-sized write to /proc/self/keycreate
would check if the current task can create unlabeled keys (which would
usually fail with -EACCESS and generate an AVC). Now it skips the check
and correctly sets the task's keycreate_sid to 0.
Bug report: https://bugzilla.redhat.com/show_bug.cgi?id=1719067
Tested using the reproducer from the report above.
Fixes: 4eb582cf1fbd ("[PATCH] keys: add a way to store the appropriate context for newly-created keys")
Reported-by: Kir Kolyshkin <kir@sacred.ru>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Since acdf52d97f82 ("selinux: convert to kvmalloc"), these check whether
an address-of value is NULL, which is pointless.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
While the endiannes is being handled properly sparse was unable to verify
this due to type inconsistency. So introduce an additional __le32
respectively _le64 variable to be passed to le32/64_to_cpu() to allow
sparse to verify proper typing. Note that this patch does not change
the generated binary on little-endian systems - on 32bit powerpc it
does change the binary.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
|
|
'ifeq ... else ifneq ... endif' notation is supported by GNU Make 3.81
or later, which is the requirement for building the kernel since
commit 37d69ee30808 ("docs: bump minimal GNU Make version to 3.81").
Use it to improve the readability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently on panic, kernel will lower the loglevel and print out pending
printk msg only with console_flush_on_panic().
Add an option for users to configure the "panic_print" to replay all
dmesg in buffer, some of which they may have never seen due to the
loglevel setting, which will help panic debugging .
[feng.tang@intel.com: keep the original console_flush_on_panic() inside panic()]
Link: http://lkml.kernel.org/r/1556199137-14163-1-git-send-email-feng.tang@intel.com
[feng.tang@intel.com: use logbuf lock to protect the console log index]
Link: http://lkml.kernel.org/r/1556269868-22654-1-git-send-email-feng.tang@intel.com
Link: http://lkml.kernel.org/r/1556095872-36838-1-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 54c7a8916a88 ("initramfs: free initrd memory if opening
/initrd.image fails"), the kernel has unconditionally attempted to free
the initrd even if it doesn't exist.
In the non-existent case this causes a boot-time splat if
CONFIG_DEBUG_VIRTUAL is enabled due to a call to virt_to_phys() with a
NULL address.
Instead we should check that the initrd actually exists and only attempt
to free it if it does.
Link: http://lkml.kernel.org/r/20190516143125.48948-1-steven.price@arm.com
Fixes: 54c7a8916a88 ("initramfs: free initrd memory if opening /initrd.image fails")
Signed-off-by: Steven Price <steven.price@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
synchronize_rcu() didn't wait for call_rcu() callbacks, so inode wb
switch may not go to the workqueue after synchronize_rcu(). Thus
previous scheduled switches was not finished even flushing the
workqueue, which will cause a NULL pointer dereferenced followed below.
VFS: Busy inodes after unmount of vdd. Self-destruct in 5 seconds. Have a nice day...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000278
evict+0xb3/0x180
iput+0x1b0/0x230
inode_switch_wbs_work_fn+0x3c0/0x6a0
worker_thread+0x4e/0x490
? process_one_work+0x410/0x410
kthread+0xe6/0x100
ret_from_fork+0x39/0x50
Replace the synchronize_rcu() call with a rcu_barrier() to wait for all
pending callbacks to finish. And inc isw_nr_in_flight after call_rcu()
in inode_switch_wbs() to make more sense.
Link: http://lkml.kernel.org/r/20190429024108.54150-1-jiufei.xue@linux.alibaba.com
Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Acked-by: Tejun Heo <tj@kernel.org>
Suggested-by: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
syzbot reported the following error from a tree with a head commit of
baf76f0c58ae ("slip: make slhc_free() silently accept an error pointer")
BUG: unable to handle kernel paging request at ffffea0003348000
#PF error: [normal kernel read fault]
PGD 12c3f9067 P4D 12c3f9067 PUD 12c3f8067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 28916 Comm: syz-executor.2 Not tainted 5.1.0-rc6+ #89
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:314 [inline]
RIP: 0010:PageCompound include/linux/page-flags.h:186 [inline]
RIP: 0010:isolate_freepages_block+0x1c0/0xd40 mm/compaction.c:579
Code: 01 d8 ff 4d 85 ed 0f 84 ef 07 00 00 e8 29 00 d8 ff 4c 89 e0 83 85 38 ff
ff ff 01 48 c1 e8 03 42 80 3c 38 00 0f 85 31 0a 00 00 <4d> 8b 2c 24 31 ff 49
c1 ed 10 41 83 e5 01 44 89 ee e8 3a 01 d8 ff
RSP: 0018:ffff88802b31eab8 EFLAGS: 00010246
RAX: 1ffffd4000669000 RBX: 00000000000cd200 RCX: ffffc9000a235000
RDX: 000000000001ca5e RSI: ffffffff81988cc7 RDI: 0000000000000001
RBP: ffff88802b31ebd8 R08: ffff88805af700c0 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffea0003348000
R13: 0000000000000000 R14: ffff88802b31f030 R15: dffffc0000000000
FS: 00007f61648dc700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffea0003348000 CR3: 0000000037c64000 CR4: 00000000001426e0
Call Trace:
fast_isolate_around mm/compaction.c:1243 [inline]
fast_isolate_freepages mm/compaction.c:1418 [inline]
isolate_freepages mm/compaction.c:1438 [inline]
compaction_alloc+0x1aee/0x22e0 mm/compaction.c:1550
There is no reproducer and it is difficult to hit -- 1 crash every few
days. The issue is very similar to the fix in commit 6b0868c820ff
("mm/compaction.c: correct zone boundary handling when resetting pageblock
skip hints"). When isolating free pages around a target pageblock, the
boundary handling is off by one and can stray into the next pageblock.
Triggering the syzbot error requires that the end of pageblock is section
or zone aligned, and that the next section is unpopulated.
A more subtle consequence of the bug is that pageblocks were being
improperly used as migration targets which potentially hurts fragmentation
avoidance in the long-term one page at a time.
A debugging patch revealed that it's definitely possible to stray outside
of a pageblock which is not intended. While syzbot cannot be used to
verify this patch, it was confirmed that the debugging warning no longer
triggers with this patch applied. It has also been confirmed that the THP
allocation stress tests are not degraded by this patch.
Link: http://lkml.kernel.org/r/20190510182124.GI18914@techsingularity.net
Fixes: e332f741a8dd ("mm, compaction: be selective about what pageblocks to clear skip hints")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: syzbot+d84c80f9fe26a0f7a734@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This macro adds some debug code to check that vmap allocations are
happened in ascending order.
By default this option is set to 0 and not active. It requires
recompilation of the kernel to activate it. Set to 1, compile the
kernel.
[urezki@gmail.com: v4]
Link: http://lkml.kernel.org/r/20190406183508.25273-4-urezki@gmail.com
Link: http://lkml.kernel.org/r/20190402162531.10888-4-urezki@gmail.com
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This macro adds some debug code to check that the augment tree is
maintained correctly, meaning that every node contains valid
subtree_max_size value.
By default this option is set to 0 and not active. It requires
recompilation of the kernel to activate it. Set to 1, compile the
kernel.
[urezki@gmail.com: v4]
Link: http://lkml.kernel.org/r/20190406183508.25273-3-urezki@gmail.com
Link: http://lkml.kernel.org/r/20190402162531.10888-3-urezki@gmail.com
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "improve vmap allocation", v3.
Objective
---------
Please have a look for the description at:
https://lkml.org/lkml/2018/10/19/786
but let me also summarize it a bit here as well.
The current implementation has O(N) complexity. Requests with different
permissive parameters can lead to long allocation time. When i say
"long" i mean milliseconds.
Description
-----------
This approach organizes the KVA memory layout into free areas of the
1-ULONG_MAX range, i.e. an allocation is done over free areas lookups,
instead of finding a hole between two busy blocks. It allows to have
lower number of objects which represent the free space, therefore to have
less fragmented memory allocator. Because free blocks are always as large
as possible.
It uses the augment tree where all free areas are sorted in ascending
order of va->va_start address in pair with linked list that provides
O(1) access to prev/next elements.
Since the tree is augment, we also maintain the "subtree_max_size" of VA
that reflects a maximum available free block in its left or right
sub-tree. Knowing that, we can easily traversal toward the lowest (left
most path) free area.
Allocation: ~O(log(N)) complexity. It is sequential allocation method
therefore tends to maximize locality. The search is done until a first
suitable block is large enough to encompass the requested parameters.
Bigger areas are split.
I copy paste here the description of how the area is split, since i
described it in https://lkml.org/lkml/2018/10/19/786
<snip>
A free block can be split by three different ways. Their names are
FL_FIT_TYPE, LE_FIT_TYPE/RE_FIT_TYPE and NE_FIT_TYPE, i.e. they
correspond to how requested size and alignment fit to a free block.
FL_FIT_TYPE - in this case a free block is just removed from the free
list/tree because it fully fits. Comparing with current design there is
an extra work with rb-tree updating.
LE_FIT_TYPE/RE_FIT_TYPE - left/right edges fit. In this case what we do
is just cutting a free block. It is as fast as a current design. Most of
the vmalloc allocations just end up with this case, because the edge is
always aligned to 1.
NE_FIT_TYPE - Is much less common case. Basically it happens when
requested size and alignment does not fit left nor right edges, i.e. it
is between them. In this case during splitting we have to build a
remaining left free area and place it back to the free list/tree.
Comparing with current design there are two extra steps. First one is we
have to allocate a new vmap_area structure. Second one we have to insert
that remaining free block to the address sorted list/tree.
In order to optimize a first case there is a cache with free_vmap objects.
Instead of allocating from slab we just take an object from the cache and
reuse it.
Second one is pretty optimized. Since we know a start point in the tree
we do not do a search from the top. Instead a traversal begins from a
rb-tree node we split.
<snip>
De-allocation. ~O(log(N)) complexity. An area is not inserted straight
away to the tree/list, instead we identify the spot first, checking if it
can be merged around neighbors. The list provides O(1) access to
prev/next, so it is pretty fast to check it. Summarizing. If merged then
large coalesced areas are created, if not the area is just linked making
more fragments.
There is one more thing that i should mention here. After modification of
VA node, its subtree_max_size is updated if it was/is the biggest area in
its left or right sub-tree. Apart of that it can also be populated back
to upper levels to fix the tree. For more details please have a look at
the __augment_tree_propagate_from() function and the description.
Tests and stressing
-------------------
I use the "test_vmalloc.sh" test driver available under
"tools/testing/selftests/vm/" since 5.1-rc1 kernel. Just trigger "sudo
./test_vmalloc.sh" to find out how to deal with it.
Tested on different platforms including x86_64/i686/ARM64/x86_64_NUMA.
Regarding last one, i do not have any physical access to NUMA system,
therefore i emulated it. The time of stressing is days.
If you run the test driver in "stress mode", you also need the patch that
is in Andrew's tree but not in Linux 5.1-rc1. So, please apply it:
http://git.cmpxchg.org/cgit.cgi/linux-mmotm.git/commit/?id=e0cf7749bade6da318e98e934a24d8b62fab512c
After massive testing, i have not identified any problems like memory
leaks, crashes or kernel panics. I find it stable, but more testing would
be good.
Performance analysis
--------------------
I have used two systems to test. One is i5-3320M CPU @ 2.60GHz and
another is HiKey960(arm64) board. i5-3320M runs on 4.20 kernel, whereas
Hikey960 uses 4.15 kernel. I have both system which could run on 5.1-rc1
as well, but the results have not been ready by time i an writing this.
Currently it consist of 8 tests. There are three of them which correspond
to different types of splitting(to compare with default). We have 3
ones(see above). Another 5 do allocations in different conditions.
a) sudo ./test_vmalloc.sh performance
When the test driver is run in "performance" mode, it runs all available
tests pinned to first online CPU with sequential execution test order. We
do it in order to get stable and repeatable results. Take a look at time
difference in "long_busy_list_alloc_test". It is not surprising because
the worst case is O(N).
# i5-3320M
How many cycles all tests took:
CPU0=646919905370(default) cycles vs CPU0=193290498550(patched) cycles
# See detailed table with results here:
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_default.txt
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_performance_patched.txt
# Hikey960 8x CPUs
How many cycles all tests took:
CPU0=3478683207 cycles vs CPU0=463767978 cycles
# See detailed table with results here:
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_default.txt
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/HiKey960_performance_patched.txt
b) time sudo ./test_vmalloc.sh test_repeat_count=1
With this configuration, all tests are run on all available online CPUs.
Before running each CPU shuffles its tests execution order. It gives
random allocation behaviour. So it is rough comparison, but it puts in
the picture for sure.
# i5-3320M
<default> vs <patched>
real 101m22.813s real 0m56.805s
user 0m0.011s user 0m0.015s
sys 0m5.076s sys 0m0.023s
# See detailed table with results here:
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_default.txt
ftp://vps418301.ovh.net/incoming/vmap_test_results_v2/i5-3320M_test_repeat_count_1_patched.txt
# Hikey960 8x CPUs
<default> vs <patched>
real unknown real 4m25.214s
user unknown user 0m0.011s
sys unknown sys 0m0.670s
I did not manage to complete this test on "default Hikey960" kernel
version. After 24 hours it was still running, therefore i had to cancel
it. That is why real/user/sys are "unknown".
This patch (of 3):
Currently an allocation of the new vmap area is done over busy list
iteration(complexity O(n)) until a suitable hole is found between two busy
areas. Therefore each new allocation causes the list being grown. Due to
over fragmented list and different permissive parameters an allocation can
take a long time. For example on embedded devices it is milliseconds.
This patch organizes the KVA memory layout into free areas of the
1-ULONG_MAX range. It uses an augment red-black tree that keeps blocks
sorted by their offsets in pair with linked list keeping the free space in
order of increasing addresses.
Nodes are augmented with the size of the maximum available free block in
its left or right sub-tree. Thus, that allows to take a decision and
traversal toward the block that will fit and will have the lowest start
address, i.e. it is sequential allocation.
Allocation: to allocate a new block a search is done over the tree until a
suitable lowest(left most) block is large enough to encompass: the
requested size, alignment and vstart point. If the block is bigger than
requested size - it is split.
De-allocation: when a busy vmap area is freed it can either be merged or
inserted to the tree. Red-black tree allows efficiently find a spot
whereas a linked list provides a constant-time access to previous and next
blocks to check if merging can be done. In case of merging of
de-allocated memory chunk a large coalesced area is created.
Complexity: ~O(log(N))
[urezki@gmail.com: v3]
Link: http://lkml.kernel.org/r/20190402162531.10888-2-urezki@gmail.com
[urezki@gmail.com: v4]
Link: http://lkml.kernel.org/r/20190406183508.25273-2-urezki@gmail.com
Link: http://lkml.kernel.org/r/20190321190327.11813-2-urezki@gmail.com
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the recent build test of linux-next, Stephen saw a build error
caused by a broken .tmp_versions/*.mod file:
https://lkml.org/lkml/2019/5/13/991
drivers/net/phy/asix.ko and drivers/net/usb/asix.ko have the same
basename, and there is a race in generating .tmp_versions/asix.mod
Kbuild has not checked this before, and it suddenly shows up with
obscure error messages when this kind of race occurs.
Non-unique module names cause various sort of problems, but it is
not trivial to catch them by eyes.
Hence, this script.
It checks not only real modules, but also built-in modules (i.e.
controlled by tristate CONFIG option, but currently compiled with =y).
Non-unique names for built-in modules also cause problems because
/sys/modules/ would fall over.
For the latest kernel, I tested "make allmodconfig all" (or more
quickly "make allyesconfig modules"), and it detected the following:
warning: same basename if the following are built as modules:
drivers/regulator/88pm800.ko
drivers/mfd/88pm800.ko
warning: same basename if the following are built as modules:
drivers/gpu/drm/bridge/adv7511/adv7511.ko
drivers/media/i2c/adv7511.ko
warning: same basename if the following are built as modules:
drivers/net/phy/asix.ko
drivers/net/usb/asix.ko
warning: same basename if the following are built as modules:
fs/coda/coda.ko
drivers/media/platform/coda/coda.ko
warning: same basename if the following are built as modules:
drivers/net/phy/realtek.ko
drivers/net/dsa/realtek.ko
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Currently menu blocks start with a pretty header but end with nothing in
the generated config. So next config options stick together with the
options from the menu block.
Let's terminate menu blocks in the generated config with a comment and
a newline if needed. Example:
...
CONFIG_BPF_STREAM_PARSER=y
CONFIG_NET_FLOW_LIMIT=y
#
# Network testing
#
CONFIG_NET_PKTGEN=y
CONFIG_NET_DROP_MONITOR=y
# end of Network testing
# end of Networking options
CONFIG_HAMRADIO=y
...
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For *-pkg targets, the LICENSES directory should be included in the
source tarball.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The 'addtree' and 'flags' in scripts/Kbuild.include are so compilecated
and ugly.
As I mentioned in [1], Kbuild should stop automatic prefixing of header
search path options.
I fixed up (almost) all Makefiles in the kernel. Now 'addtree' and
'flags' have been removed.
Kbuild still caters to add $(srctree)/$(src) and $(objtree)/$(obj)
to the header search path for O= building, but never touches extra
compiler options from ccflags-y etc.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5bc6
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5bc6
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
I was able to build without these extra header search paths.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
As of Linux 5.1, alpha and s390 are the last architectures that
have defconfig in arch/*/ instead of arch/*/configs/.
$ find arch -name defconfig | sort
arch/alpha/defconfig
arch/arm64/configs/defconfig
arch/csky/configs/defconfig
arch/nds32/configs/defconfig
arch/riscv/configs/defconfig
arch/s390/defconfig
The arch/$(ARCH)/defconfig is the hard-coded default in Kconfig,
and I want to deprecate it after evacuating the remaining defconfig
into the standard location, arch/*/configs/.
Define KBUILD_DEFCONFIG like other architectures, and move defconfig
into the configs/ subdirectory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
|
|
If the compiler specified by $(CC) is not present, the Kconfig stage
sprinkles 'not found' messages, then succeeds.
$ make CROSS_COMPILE=foo defconfig
/bin/sh: 1: foogcc: not found
/bin/sh: 1: foogcc: not found
*** Default configuration is based on 'x86_64_defconfig'
./scripts/gcc-version.sh: 17: ./scripts/gcc-version.sh: foogcc: not found
./scripts/gcc-version.sh: 18: ./scripts/gcc-version.sh: foogcc: not found
./scripts/gcc-version.sh: 19: ./scripts/gcc-version.sh: foogcc: not found
./scripts/gcc-version.sh: 17: ./scripts/gcc-version.sh: foogcc: not found
./scripts/gcc-version.sh: 18: ./scripts/gcc-version.sh: foogcc: not found
./scripts/gcc-version.sh: 19: ./scripts/gcc-version.sh: foogcc: not found
./scripts/clang-version.sh: 11: ./scripts/clang-version.sh: foogcc: not found
./scripts/gcc-plugin.sh: 11: ./scripts/gcc-plugin.sh: foogcc: not found
init/Kconfig:16:warning: 'GCC_VERSION': number is invalid
#
# configuration written to .config
#
Terminate parsing files immediately if $(CC) or $(LD) is not found.
"make *config" will fail more nicely.
$ make CROSS_COMPILE=foo defconfig
*** Default configuration is based on 'x86_64_defconfig'
scripts/Kconfig.include:34: compiler 'foogcc' not found
make[1]: *** [scripts/kconfig/Makefile;82: defconfig] Error 1
make: *** [Makefile;557: defconfig] Error 2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
syncconfig is responsible for keeping auto.conf up-to-date, so if it
fails for any reason, the build must be terminated immediately.
However, since commit 9390dff66a52 ("kbuild: invoke syncconfig if
include/config/auto.conf.cmd is missing"), Kbuild continues running
even after syncconfig fails.
You can confirm this by intentionally making syncconfig error out:
diff --git a/scripts/kconfig/confdata.c b/scripts/kconfig/confdata.c
index 08ba146..307b9de 100644
--- a/scripts/kconfig/confdata.c
+++ b/scripts/kconfig/confdata.c
@@ -1023,6 +1023,9 @@ int conf_write_autoconf(int overwrite)
FILE *out, *tristate, *out_h;
int i;
+ if (overwrite)
+ return 1;
+
if (!overwrite && is_present(autoconf_name))
return 0;
Then, syncconfig fails, but Make would not stop:
$ make -s mrproper allyesconfig defconfig
$ make
scripts/kconfig/conf --syncconfig Kconfig
*** Error during sync of the configuration.
make[2]: *** [scripts/kconfig/Makefile;69: syncconfig] Error 1
make[1]: *** [Makefile;557: syncconfig] Error 2
make: *** [include/config/auto.conf.cmd] Deleting file 'include/config/tristate.conf'
make: Failed to remake makefile 'include/config/auto.conf'.
SYSTBL arch/x86/include/generated/asm/syscalls_32.h
SYSHDR arch/x86/include/generated/asm/unistd_32_ia32.h
SYSHDR arch/x86/include/generated/asm/unistd_64_x32.h
SYSTBL arch/x86/include/generated/asm/syscalls_64.h
[ continue running ... ]
The reason is in the behavior of a pattern rule with multi-targets.
%/auto.conf %/auto.conf.cmd %/tristate.conf: $(KCONFIG_CONFIG)
$(Q)$(MAKE) -f $(srctree)/Makefile syncconfig
GNU Make knows this rule is responsible for making all the three files
simultaneously. As far as examined, auto.conf.cmd is the target in
question when this rule is invoked. It is probably because auto.conf.cmd
is included below the inclusion of auto.conf.
The inclusion of auto.conf is mandatory, while that of auto.conf.cmd
is optional. GNU Make does not care about the failure in the process
of updating optional include files.
I filed this issue (https://savannah.gnu.org/bugs/?56301) in case this
behavior could be improved somehow in future releases of GNU Make.
Anyway, it is quite easy to fix our Makefile.
Given that auto.conf is already a mandatory include file, there is no
reason to stick auto.conf.cmd optional. Make it mandatory as well.
Cc: linux-stable <stable@vger.kernel.org> # 5.0+
Fixes: 9390dff66a52 ("kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Also, sort the patterns alphabetically. Update the comment since
we have non-git files here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We do not support old Clang versions. Upgrade your clang version
if any of these flags is unsupported.
Let's add all flags inside ifdef CONFIG_CC_IS_CLANG unconditionally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
|
|
This is no longer a valid option in clang, it was removed in 3.5, which
we don't support.
https://github.com/llvm/llvm-project/commit/cb3f812b6b9fab8f3b41414f24e90222170417b4
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These flags are documented in the GCC 4.6 manual, and recognized by
Clang as well. Let's rip off the cc-option / cc-disable-warning switches.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
|
|
This flag is documented in the GCC 4.6 manual, and recognized by
Clang as well. Let's rip off the cc-option switch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
|
|
These generic-y defines do not have the corresponding generic header
in include/asm-generic/, so they are definitely invalid.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Do not descend to sub-directories when unneeded.
I used subdir-$(CONFIG_...) for hidraw, seccomp, and vfs because
they only contain host programs.
While we are here, let's add SPDX License tag, and sort the directories
alphabetically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This warning was disabled by commit bd664f6b3e37 ("disable new
gcc-7.1.1 warnings for now") just because it was too noisy.
Thanks to Arnd Bergmann, all warnings have been fixed. Now, we are
ready to re-enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
|
scripts/link-vmlinux.sh is part of kbuild so extend the pattern to match
any vmlinux related scripts.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
arch/sh/boot/.gitignore has the pattern "vmlinux*"; this is effective
not only for the current directory, but also for any sub-directories.
So, from the point of .gitignore grammar, the following check-in files
are also considered to be ignored:
arch/sh/boot/compressed/vmlinux.scr
arch/sh/boot/romimage/vmlinux.scr
As the manual gitignore(5) says "Files already tracked by Git are not
affected", this is not a problem as far as Git is concerned.
However, Git is not the only program that parses .gitignore because
.gitignore is useful to distinguish build artifacts from source files.
For example, tar(1) supports the --exclude-vcs-ignore option. As of
writing, this option does not work perfectly, but it intends to create
a tarball excluding files specified by .gitignore.
So, I believe it is better to fix this issue.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html
Cc: clang-built-linux@googlegroups.com
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html
Cc: clang-built-linux@googlegroups.com
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Having a symbolic link arch/*/boot/dts/include/dt-bindings was
deprecated by commit d5d332d3f7e8 ("devicetree: Move include
prefixes from arch to separate directory").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handling of aborted journal is a special code path different from
standard ext4_error() one and it can call panic() as well. Commit
1dc1097ff60e ("ext4: avoid panic during forced reboot") forgot to update
this path so fix that omission.
Fixes: 1dc1097ff60e ("ext4: avoid panic during forced reboot")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 5.1
|
|
i2c_new_dummy is typically called from the probe function of the
driver for the primary i2c client. It requires calls to
i2c_unregister_device in the error path of the probe function and
in the remove function.
This can be simplified by introducing a device-managed version.
Note the changed error case return value type: i2c_new_dummy returns
NULL whilst devm_i2c_new_dummy_device returns an ERR_PTR.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[wsa: rename new functions and fix minor kdoc issues]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently i2c_new_device and i2c_new_dummy return just NULL in error
case although they have more error details internally. Therefore move
the functionality into new functions returning detailed errors and
add wrappers for compatibility with the current API.
This allows to use these functions with detailed error codes within
the i2c core or for API extensions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[wsa: rename new functions and fix minor kdoc issues]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
kfree() after kobject_put(). Who ever wrote this was on crack.
Fixes: 7e8039795a80 ("powerpc/cacheinfo: Fix kobject memleak")
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Accesses by userspace to random addresses outside the user or kernel
address range will generate an SLB fault. When we handle that fault we
classify the effective address into several classes, eg. user, kernel
linear, kernel virtual etc.
For addresses that are completely outside of any valid range, we
should not insert an SLB entry at all, and instead immediately an
exception.
In the past this was handled in two ways. Firstly we would check the
top nibble of the address (using REGION_ID(ea)) and that would tell us
if the address was user (0), kernel linear (c), kernel virtual (d), or
vmemmap (f). If the address didn't match any of these it was invalid.
Then for each type of address we would do a secondary check. For the
user region we check against H_PGTABLE_RANGE, for kernel linear we
would mask the top nibble of the address and then check the address
against MAX_PHYSMEM_BITS.
As part of commit 0034d395f89d ("powerpc/mm/hash64: Map all the kernel
regions in the same 0xc range") we replaced REGION_ID() with
get_region_id() and changed the masking of the top nibble to only mask
the top two bits, which introduced a bug.
Addresses less than (4 << 60) are still handled correctly, they are
either less than (1 << 60) in which case they are subject to the
H_PGTABLE_RANGE check, or they are correctly checked against
MAX_PHYSMEM_BITS.
However addresses from (4 << 60) to ((0xc << 60) - 1), are incorrectly
treated as kernel linear addresses in get_region_id(). Then the top
two bits are cleared by EA_MASK in slb_allocate_kernel() and the
address is checked against MAX_PHYSMEM_BITS, which it passes due to
the masking. The end result is we incorrectly insert SLB entries for
those addresses.
That is not actually catastrophic, having inserted the SLB entry we
will then go on to take a page fault for the address and at that point
we detect the problem and report it as a bad fault.
Still we should not be inserting those entries, or treating them as
kernel linear addresses in the first place. So fix get_region_id() to
detect addresses in that range and return an invalid region id, which
we cause use to not insert an SLB entry and directly report an
exception.
Fixes: 0034d395f89d ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Drop change to EA_MASK for now, rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
Stephen Smalley
Ondrej Mosnacek
Aaron Goidel
Paul Moore
Richard Guy Briggs
Nicholas Mc Guire
Linus Torvalds
Masahiro Yamada
Feng Tang
Steven Price
Jiufei Xue
Mel Gorman
Uladzislau Rezki (Sony)
Alexander Popov
Nathan Chancellor
Krzysztof Kozlowski
Nick Desaulniers
Jan Kara
Heiner Kallweit
Tobin C. Harding
Aneesh Kumar K.V