| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add the PCI-ID of the AQR105-based Tehuti TN4010 cards to allow loading
of the tn40xx driver on these cards. Here, I chose the detailed definition
with the subvendor ID similar to the QT2025 cards with the PCI-ID
TEHUTI:0x4022, because there is a card with an AQ2104 hiding amongst the
AQR105 cards, and they all come with the same PCI-ID (TEHUTI:0x4025). But
the AQ2104 is currently not supported.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-7-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare the tn40xx driver to load for Tehuti TN9510 cards, which require
bit 3 in the register TN40_REG_MDIO_CMD_STAT to be set. The function of bit
3 is unclear, but may have something to do with the length of the preamble
in the MDIO communication. If bit 3 is not set, the PHY will not be found
when performing a scan for PHYs. Use the available tn40_mdio_set_speed
function which includes setting bit 3. Just move the function to before the
devm_mdio_register function, which scans the mdio bus for PHYs.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-6-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of an AQR105-based device, create a software node for the mdio
function, with a child node for the Aquantia AQR105 PHY, providing a
firmware-name (and a bit more, which may be used for future checks) to
allow the PHY to load a MAC specific firmware from the file system.
The name of the PHY software node follows the naming convention suggested
in the patch for the mdiobus_scan function (in the same patch series).
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-5-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch makes functions that were provided for aqr107 applicable to
aqr105, or replaces generic functions with specific ones. Since the aqr105
was introduced before NBASE-T was defined (or 802.3bz), there are a number
of vendor specific registers involved in the definition of the
advertisement, in auto-negotiation and in the setting of the speed. The
functions have been written following the downstream driver for TN4010
cards with aqr105 PHY, and use code from aqr107 functions wherever it
seemed to make sense.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-4-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow the firmware name of an Aquantia PHY alternatively be provided by the
property "firmware-name" of a swnode. This software node may be provided by
the MAC or MDIO driver.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-3-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Re-use the AQR107 probe function to load the firmware on the AQR105 (and
to probe the HWMON).
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-2-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch will allow to use a swnode/fwnode defined for a phy_device. The
MDIO bus (mii_bus) needs to contain nodes for the PHY devices, named
"ethernet-phy@i", with i being the MDIO address (0 .. PHY_MAX_ADDR - 1).
The fwnode is only attached to the phy_device if there isn't already an
fwnode attached.
fwnode_get_named_child_node will increase the usage counter of the fwnode.
However, no new code is needed to decrease the counter again, since this is
already implemented in the phy_device_release function.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-1-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds support for running XDP programs on DQ, along with
rudimentary processing for XDP_DROP and XDP_PASS. These actions require
very limited driver functionality when it comes to processing an XDP
buffer, so currently if the XDP action is not XDP_PASS, the packet is
dropped and stats are updated.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaliginedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy<hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-7-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to support installing an XDP program on DQ, RX buffers need to
be reposted using 4K buffers, which is larger than the default packet
buffer size of 2K. This is needed to accommodate the extra head and tail
that accompanies the data portion of an XDP buffer. Continuing to use 2K
buffers would mean that the packet buffer size for the NIC would have to
be restricted to 2048 - 320 - 256 = 1472B. However, this is problematic
for two reasons: first, 1472 is not a packet buffer size accepted by
GVE; second, at least 1474B of buffer space is needed to accommodate an
MTU of 1460, which is the default on GCP. As such, we allocate 4K
buffers, and post a 2K section of those 4K buffers (offset relative to
the XDP headroom) to the NIC for DMA to avoid a potential extra copy.
Because the GQ-QPL datapath requires copies regardless, this change was
not needed to support XDP in that case.
To capture this subtlety, a new field, packet_buffer_truesize, has been
added to the rx ring struct to represent size of the allocated buffer,
while packet_buffer_size has been left to represent the portion of the
buffer posted to the NIC.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-6-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The data_buffer_size_dqo field in gve_priv and the packet_buffer_size
field in gve_rx_ring theoretically have the same meaning, but they are
defined in two different places and used in two separate contexts. There
is no good reason for this, so this change merges those fields into the
packet_buffer_size field in the RX ring.
This change also introduces a packet_buffer_size field to struct
gve_rx_queue_config to account for cases where queues are not allocated,
such as when the interface is down.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-5-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit ebdfae0d377b ("gve: adopt page pool for DQ RDA mode") introduced
a buf_size field to the gve_rx_slot_page_info struct, which can be used
in the datapath to take the place of the packet_buffer_size field, as it
will already be hot in the cache due to its extensive use. Using the
buf_size field in the datapath frees up the packet_buffer_size field in
the GQ-specific RX cacheline to be generalized for GQ and DQ (in the
next patch), as there is currently no common packet buffer size field
between the two queue formats.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-4-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An earlier patch series[1] introduced RX/TX ring allocation configuration
structs which contained metadata used to allocate and configure new RX
and TX rings. This led to a much cleaner and safer allocation pattern
wherein queue resources were not deallocated until new queue resources
were successfully allocated.
Migrate the XDP allocation path to use the same pattern to allow for the
existence of a single allocation path instead of relying on XDP-specific
allocation methods. These extra allocation methods result in the
duplication of many existing behaviors while being prone to error when
configuration changes unrelated to XDP occur.
Link: https://lore.kernel.org/netdev/20240122182632.1102721-1-shailend@google.com/ [1]
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-3-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These statistics pollute the hotpath and do not have any real-world use
or meaning.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-2-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we fail to configure the MAC or PCS according to the desired mode,
do not allow the network link to come up until we have successfully
configured the MAC and PCS. This improves phylink's behaviour when an
error occurs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1twkqO-0006FI-Gm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This adds LL Privacy (bit 22) to Read Controller Information so the likes
of bluetoothd(1) can detect when the controller supports it or not.
Fixes: e209e5ccc5ac ("Bluetooth: MGMT: Mark LL Privacy as stable")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some controllers seems to generate HCI_EV_LE_DIRECT_ADV_REPORT even when
scan_filter is not set to 0x02 or 0x03, which indicates that local
privacy is enabled, causing them to be ignored thus breaking
auto-connect logic:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Public (0x00)
Filter policy: Ignore not in accept list (0x01)
...
> HCI Event: LE Meta Event (0x3e) plen 18
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: XX:XX:XX:XX:XX:XX (Static)
Direct address type: Random (0x01)
Direct address: XX:XX:XX:XX:XX:XX (Non-Resolvable)
RSSI: -54 dBm (0xca)
So this attempts to mitigate the above problem by skipping checking of
direct_addr if local privacy is not enabled.
Link: https://github.com/bluez/bluez/issues/1138
Fixes: e209e5ccc5ac ("Bluetooth: MGMT: Mark LL Privacy as stable")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes a kernel panic seen during release FW in a stress test
scenario where WLAN and BT FW download occurs simultaneously, and due to
a HW bug, chip sends out only 1 bootloader signatures.
When driver receives the bootloader signature, it enters FW download
mode, but since no consequtive bootloader signatures seen, FW file is
not requested.
After 60 seconds, when FW download times out, release_firmware causes a
kernel panic.
[ 2601.949184] Unable to handle kernel paging request at virtual address 0000312e6f006573
[ 2601.992076] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000111802000
[ 2601.992080] [0000312e6f006573] pgd=0000000000000000, p4d=0000000000000000
[ 2601.992087] Internal error: Oops: 0000000096000021 [#1] PREEMPT SMP
[ 2601.992091] Modules linked in: algif_hash algif_skcipher af_alg btnxpuart(O) pciexxx(O) mlan(O) overlay fsl_jr_uio caam_jr caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine authenc libdes crct10dif_ce polyval_ce snd_soc_fsl_easrc snd_soc_fsl_asoc_card imx8_media_dev(C) snd_soc_fsl_micfil polyval_generic snd_soc_fsl_xcvr snd_soc_fsl_sai snd_soc_imx_audmux snd_soc_fsl_asrc snd_soc_imx_card snd_soc_imx_hdmi snd_soc_fsl_aud2htx snd_soc_fsl_utils imx_pcm_dma dw_hdmi_cec flexcan can_dev
[ 2602.001825] CPU: 2 PID: 20060 Comm: hciconfig Tainted: G C O 6.6.23-lts-next-06236-gb586a521770e #1
[ 2602.010182] Hardware name: NXP i.MX8MPlus EVK board (DT)
[ 2602.010185] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2602.010191] pc : _raw_spin_lock+0x34/0x68
[ 2602.010201] lr : free_fw_priv+0x20/0xfc
[ 2602.020561] sp : ffff800089363b30
[ 2602.020563] x29: ffff800089363b30 x28: ffff0000d0eb5880 x27: 0000000000000000
[ 2602.020570] x26: 0000000000000000 x25: ffff0000d728b330 x24: 0000000000000000
[ 2602.020577] x23: ffff0000dc856f38
[ 2602.033797] x22: ffff800089363b70 x21: ffff0000dc856000
[ 2602.033802] x20: ff00312e6f006573 x19: ffff0000d0d9ea80 x18: 0000000000000000
[ 2602.033809] x17: 0000000000000000 x16: 0000000000000000 x15: 0000aaaad80dd480
[ 2602.083320] x14: 0000000000000000 x13: 00000000000001b9 x12: 0000000000000002
[ 2602.083326] x11: 0000000000000000 x10: 0000000000000a60 x9 : ffff800089363a30
[ 2602.083333] x8 : ffff0001793d75c0 x7 : ffff0000d6dbc400 x6 : 0000000000000000
[ 2602.083339] x5 : 00000000410fd030 x4 : 0000000000000000 x3 : 0000000000000001
[ 2602.083346] x2 : 0000000000000000 x1 : 0000000000000001 x0 : ff00312e6f006573
[ 2602.083354] Call trace:
[ 2602.083356] _raw_spin_lock+0x34/0x68
[ 2602.083364] release_firmware+0x48/0x6c
[ 2602.083370] nxp_setup+0x3c4/0x540 [btnxpuart]
[ 2602.083383] hci_dev_open_sync+0xf0/0xa34
[ 2602.083391] hci_dev_open+0xd8/0x178
[ 2602.083399] hci_sock_ioctl+0x3b0/0x590
[ 2602.083405] sock_do_ioctl+0x60/0x118
[ 2602.083413] sock_ioctl+0x2f4/0x374
[ 2602.091430] __arm64_sys_ioctl+0xac/0xf0
[ 2602.091437] invoke_syscall+0x48/0x110
[ 2602.091445] el0_svc_common.constprop.0+0xc0/0xe0
[ 2602.091452] do_el0_svc+0x1c/0x28
[ 2602.091457] el0_svc+0x40/0xe4
[ 2602.091465] el0t_64_sync_handler+0x120/0x12c
[ 2602.091470] el0t_64_sync+0x190/0x194
Fixes: e3c4891098c8 ("Bluetooth: btnxpuart: Handle FW Download Abort scenario")
Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This handles the scenario where the driver receives an error code after
sending cmd5 or cmd7 in the bootloader signature during FW download.
The bootloader error code is handled by the driver and FW offset is
corrected accordingly, and the cmd5 or cmd7 is re-sent to the controller
in case of CRC error.
Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This corrects the bootloader error codes for NXP chipsets.
Since we have a common handling for all error codes, there is no backward
compatibility issue.
Added error handling for CRC error code in V3 bootloader signature.
Fixes: 27489364299a ("Bluetooth: btnxpuart: Add handling for boot-signature timeout errors")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Based on the patch series [1], the enablement of interface switching for
RPL-P will use the same handling as ADL-N.
Link: https://patchwork.kernel.org/project/netdevbpf/cover/20250227121522.1802832-1-yong.liang.choong@linux.intel.com/ [1]
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250324062742.462771-1-yong.liang.choong@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PCI functions
- pcim_iomap_regions() and
- pcim_iomap_table()
have been deprecated.
Replace them with their successor function, pcim_iomap_region().
Make variable declaration order at closeby places comply with reverse
christmas tree order.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Tested-by: Henry Chen <chenx97@aosc.io>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250324092928.9482-6-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Functions prefixed with "pcim_" are managed devres functions which
perform automatic cleanup once the driver unloads. It is, thus, not
necessary to call any cleanup functions in remove() callbacks.
Remove the pcim_ cleanup function calls in the remove() callbacks.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Tested-by: Henry Chen <chenx97@aosc.io>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250324092928.9482-5-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
loongson_dwmac_probe() contains a loop which doesn't have an effect,
because it tries to call pcim_iomap_regions() with the same parameters
several times. The break statement at the loop's end furthermore ensures
that the loop only runs once anyways.
Remove the surplus loop.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Tested-by: Henry Chen <chenx97@aosc.io>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250324092928.9482-4-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
icsk->icsk_ack.timeout can be replaced by icsk->csk_delack_timer.expires
This saves 8 bytes in TCP/DCCP sockets and helps for better cache locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250324203607.703850-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
icsk->icsk_timeout can be replaced by icsk->icsk_retransmit_timer.expires
This saves 8 bytes in TCP/DCCP sockets and helps for better cache locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250324203607.703850-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure that all accesses to mp_params are under the netdev
instance lock. The only change we need is to move
dev_memory_provider_uninstall() under the lock.
Appropriately swap the asserts.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev netlink is the only reader of netdev_{,rx_}queue->napi,
and it already holds netdev->lock. Switch protection of
the writes to netdev->lock to "ops protected".
The expectation will be now that accessing queue->napi
will require netdev->lock for "ops locked" drivers, and
rtnl_lock for all other drivers.
Current "ops locked" drivers don't require any changes.
gve and netdevsim use _locked() helpers right next to
netif_queue_set_napi() so they must be holding the instance
lock. iavf doesn't call it. bnxt is a bit messy but all paths
seem locked.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers which opt into instance lock protection of ops should
only call set_real_num_*_queues() under the instance lock.
This means that queue counts are double protected (writes
are under both rtnl_lock and instance lock, readers under
either).
Some readers may still be under the rtnl_lock, however, so for
now we need double protection of writers.
OTOH queue API paths are only under the protection of the instance
lock, so we need to validate that the instance is actually locking
ops, otherwise the input checks we do against queue count are racy.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Try to define some terminology for which fields are protected
by which lock and how. Some fields are protected by both rtnl_lock
and instance lock which is hard to talk about without having
a "key phrase" to refer to a particular protection scheme.
"ops protected" fields are defined later in the series, one by one.
Add ASSERT_RTNL() to netdev_ops_assert_locked() for drivers
not other instance protection of ops. Hopefully it's not too
confusion that netdev_lock_ops() does not match the lock which
netdev_ops_assert_locked() will assert, exactly. The noun "ops"
is in a different place in the name, so I think it's acceptable...
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
lockdep asserts and predicates can operate on const pointers.
In the future this will let us add asserts in functions
which operate on const pointers like dev_get_min_mp_channel_count().
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit a953be53ce40 ("net-sysfs: add support for device-specific
rx queue sysfs attributes"), so for at least a decade now it is safe
to call net_rx_queue_update_kobjects() when SYSFS=n. That function
does its own ifdef-inery and will return 0. Remove the unnecessary
stub for netif_set_real_num_rx_queues().
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A recent commit added taking the netdev instance lock
in netdev_nl_bind_rx_doit(), but didn't remove it in
net_devmem_unbind_dmabuf() which it calls from an error path.
Always expect the callers of net_devmem_unbind_dmabuf() to
hold the lock. This is consistent with net_devmem_bind_dmabuf().
(Not so) coincidentally this also protects mp_param with the instance
lock, which the rest of this series needs.
Fixes: 1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
Reviewed-by: Mina Almasry <almasrymina@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250324224537.248800-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the unwanted leading whitespace.
Fixes: 6ed83047389c ("Bluetooth: btintel_pcie: Setup buffers for firmware traces")
Fixes: bb3569ac3604 ("Bluetooth: btintel: Add DSBR support for ScP")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BRDS - Bluetooth Regulatory Domain Specific absorption rate
Bluetooth has regulatory limitations which prohibit or allow usage of certain
bands or channels as well as limiting Tx power. The Tx power values can be
configured in ACPI table. This patch reads from ACPI entry configures the
controller accordingly.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Ensure interrupts are not re-enabled when the IRQ handler has already been
removed. This prevents unexpected IRQ handler execution due to stale or
unhandled interrupts.
Modify btmtksdio_txrx_work to check if bdev->func->irq_handler exists
before calling sdio_writel to enable interrupts.
Co-developed-by: Pedro Tsai <pedro.tsai@mediatek.com>
Signed-off-by: Pedro Tsai <pedro.tsai@mediatek.com>
Co-developed-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Remove the resetting step before downloading the fw, as it may cause
other usb devices to fail to initialise when connected during boot
on kernels 6.11 and newer.
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Support TX timestamping in SCO sockets.
Not available for hdevs without SCO_FLOWCTL.
Support MSG_ERRQUEUE in SCO recvmsg.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Support TX timestamping in L2CAP sockets.
Support MSG_ERRQUEUE recvmsg.
For other than SOCK_STREAM L2CAP sockets, if a packet from sendmsg() is
fragmented, only the first ACL fragment is timestamped.
For SOCK_STREAM L2CAP sockets, use the bytestream convention and
timestamp the last fragment and count bytes in tskey.
Timestamps are not generated in the Enhanced Retransmission mode, as
meaning of COMPLETION stamp is unclear if L2CAP layer retransmits.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add BT_SCM_ERROR socket CMSG type.
Support TX timestamping in ISO sockets.
Support MSG_ERRQUEUE in ISO recvmsg.
If a packet from sendmsg() is fragmented, only the first ACL fragment is
timestamped.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Support enabling TX timestamping for some skbs, and track them until
packet completion. Generate software SCM_TSTAMP_COMPLETION when getting
completion report from hardware.
Generate software SCM_TSTAMP_SND before sending to driver. Sending from
driver requires changes in the driver API, and drivers mostly are going
to send the skb immediately.
Make the default situation with no COMPLETION TX timestamping more
efficient by only counting packets in the queue when there is nothing to
track. When there is something to track, we need to make clones, since
the driver may modify sent skbs.
The tx_q queue length is bounded by the hdev flow control, which will
not send new packets before it has got completion reports for old ones.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add SOF_TIMESTAMPING_TX_COMPLETION, for requesting a software timestamp
when hardware reports a packet completed.
Completion tstamp is useful for Bluetooth, as hardware timestamps do not
exist in the HCI specification except for ISO packets, and the hardware
has a queue where packets may wait. In this case the software SND
timestamp only reflects the kernel-side part of the total latency
(usually small) and queue length (usually 0 unless HW buffers
congested), whereas the completion report time is more informative of
the true latency.
It may also be useful in other cases where HW TX timestamps cannot be
obtained and user wants to estimate an upper bound to when the TX
probably happened.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This logs the devcd dumps with hci_recv_diag so they appear in the
monitor traces with proper timestamps which can then be used to relate
the HCI traffic that caused the dump:
= Vendor Diagnostic (len 174)
42 6c 75 65 74 6f 6f 74 68 20 64 65 76 63 6f 72 Bluetooth devcor
65 64 75 6d 70 0a 53 74 61 74 65 3a 20 32 0a 00 edump.State: 2..
43 6f 6e 74 72 6f 6c 6c 65 72 20 4e 61 6d 65 3a Controller Name:
20 76 68 63 69 5f 63 74 72 6c 0a 46 69 72 6d 77 vhci_ctrl.Firmw
61 72 65 20 56 65 72 73 69 6f 6e 3a 20 76 68 63 are Version: vhc
69 5f 66 77 0a 44 72 69 76 65 72 3a 20 76 68 63 i_fw.Driver: vhc
69 5f 64 72 76 0a 56 65 6e 64 6f 72 3a 20 76 68 i_drv.Vendor: vh
63 69 0a 2d 2d 2d 20 53 74 61 72 74 20 64 75 6d ci.--- Start dum
70 20 2d 2d 2d 0a 74 65 73 74 20 64 61 74 61 00 p ---.test data.
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 ..............
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Return Parameters is not only status, also bdaddr:
BLUETOOTH CORE SPECIFICATION Version 5.4 | Vol 4, Part E
page 1870:
BLUETOOTH CORE SPECIFICATION Version 5.0 | Vol 2, Part E
page 802:
Return parameters:
Status:
Size: 1 octet
BD_ADDR:
Size: 6 octets
Note that it also fixes the warning:
"Bluetooth: hci0: unexpected cc 0x041a length: 7 > 1"
Fixes: c8992cffbe741 ("Bluetooth: hci_event: Use of a function table to handle Command Complete")
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This sets HCI_QUIRK_SYNC_FLOWCTL_SUPPORTED which indicates that
controllers created by vhci driver support Sync Flow Control.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This enables buffer flow control for SCO/eSCO
(see: Bluetooth Core 6.0 spec: 6.22. Synchronous Flow Control Enable),
recently this has caused the following problem and is actually a nice
addition for the likes of Socket TX complete:
< HCI Command: Read Buffer Size (0x04|0x0005) plen 0
> HCI Event: Command Complete (0x0e) plen 11
Read Buffer Size (0x04|0x0005) ncmd 1
Status: Success (0x00)
ACL MTU: 1021 ACL max packet: 5
SCO MTU: 240 SCO max packet: 8
...
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
< SCO Data TX: Handle 257 flags 0x00 dlen 120
> HCI Event: Hardware Error (0x10) plen 1
Code: 0x0a
To fix the code will now attempt to enable buffer flow control when
HCI_QUIRK_SYNC_FLOWCTL_SUPPORTED is set by the driver:
< HCI Command: Write Sync Fl.. (0x03|0x002f) plen 1
Flow control: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4
Write Sync Flow Control Enable (0x03|0x002f) ncmd 1
Status: Success (0x00)
On success then HCI_SCO_FLOWCTL would be set which indicates sco_cnt
shall be used for flow contro.
Fixes: 7fedd3bb6b77 ("Bluetooth: Prioritize SCO traffic")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Pauli Virtanen <pav@iki.fi>
|
|
This fixes the following warning:
drivers/bluetooth/btintel_pcie.c:695:20: warning: unused function 'btintel_pcie_in_rom' [-Wunused-function]
695 | static inline bool btintel_pcie_in_rom(struct btintel_pcie_data *data)
| ^~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Driver dumps device core dump on firmware exception.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for setting BD address during hci registration. NXP
FW does not allow vendor commands unless it receives a reset command
after FW download and initialization done.
As a workaround, the .set_bdaddr callback function will first send the
HCI reset command, followed by the actual vendor command to set BD
address.
The driver checks for the local-bd-address property in device tree, and
if preset, it sets the HCI_QUIRK_USE_BDADDR_PROPERTY quirk.
With this quirk set, the driver's set_bdaddr callback function is called
after FW download is complete and before HCI initialization, which sends
the hci reset and 3f 22 commands. During initialization, kernel reads
the newly set BD address from the controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Korsnes <johan.korsnes@remarkable.no>
Signed-off-by: Kristian Krohn <kristian.krohn@remarkable.no>
Tested-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Allow user to set custom BD address for NXP chipsets.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for Bluetooth Coredump feature to BTNXPUART driver to
collect FW dumps on demand, or in case FW goes in a bad state.
To trigger manual FW dump, following command can be used:
echo 1 > /sys/class/bluetooth/hci0/device/coredump
Once FW dump is complete, it can be written to a file:
cat /sys/class/bluetooth/hci0/devcoredump/data > fw_dump
While FW dump is in progress, any HCI command will return -EBUSY.
After FW dump is complete, driver will give HCI_NXP_IND_RESET command
which soft-resets the chip, allowing FW re-download.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
Hans-Frieder Vogt
Joshua Washington
Russell King (Oracle)
Luiz Augusto von Dentz
Neeraj Sanjay Kale
Choong Yong Liang
Philipp Stanner
Eric Dumazet
Jakub Kicinski
Kiran K
Vijay Satija
Sean Wang
Hao Qin
Pauli Virtanen
Wentao Guan