| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce the attack vector and stop generating IPv6 Fragment Header for
paths with an MTU smaller than the minimum required IPv6 MTU
size (1280 byte) - called atomic fragments.
See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1]
for more information and how this "feature" can be misused.
[1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I.e. one-to-many sockets in SCTP are not required to explicitly
call into connect(2) or sctp_connectx(2) prior to data exchange.
Instead, they can directly invoke sendmsg(2) and the SCTP stack
will automatically trigger connection establishment through 4WHS
via sctp_primitive_ASSOCIATE(). However, this in its current
implementation is racy: INIT is being sent out immediately (as
it cannot be bundled anyway) and the rest of the DATA chunks are
queued up for later xmit when connection is established, meaning
sendmsg(2) will return successfully. This behaviour can result
in an undesired side-effect that the kernel made the application
think the data has already been transmitted, although none of it
has actually left the machine, worst case even after close(2)'ing
the socket.
Instead, when the association from client side has been shut down
e.g. first gracefully through SCTP_EOF and then close(2), the
client could afterwards still receive the server's INIT_ACK due
to a connection with higher latency. This INIT_ACK is then considered
out of the blue and hence responded with ABORT as there was no
alive assoc found anymore. This can be easily reproduced f.e.
with sctp_test application from lksctp. One way to fix this race
is to wait for the handshake to actually complete.
The fix defers waiting after sctp_primitive_ASSOCIATE() and
sctp_primitive_SEND() succeeded, so that DATA chunks cooked up
from sctp_sendmsg() have already been placed into the output
queue through the side-effect interpreter, and therefore can then
be bundeled together with COOKIE_ECHO control chunks.
strace from example application (shortened):
socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5
sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")},
msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...},
msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF
close(3) = 0
tcpdump before patch (fooling the application):
22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684]
22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591]
22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT]
tcpdump after patch:
14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729]
14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492]
14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...]
14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0]
14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...]
14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0]
14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...]
14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0]
14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN]
14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK]
14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE]
Looks like this bug is from the pre-git history museum. ;)
Fixes: 08707d5482df ("lksctp-2_5_31-0_5_1.patch")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to the problem Jeff Layton reported, I looked at the code
and reproduced the same warning by subscribing and removing the genl
family with a socket still open. This is a fairly tricky race which
originates in the fact that generic netlink allows the family to go
away while sockets are still open - unlike regular netlink which has
a module refcount for every open socket so in general this cannot be
triggered.
Trying to resolve this issue by the obvious locking isn't possible as
it will result in deadlocks between unregistration and group unbind
notification (which incidentally lockdep doesn't find due to the home
grown locking in the netlink table.)
To really resolve this, introduce a "closing socket" reference counter
(for generic netlink only, as it's the only affected family) in the
core netlink code and use that in generic netlink to wait for all the
sockets that are being closed at the same time as a generic netlink
family is removed.
This fixes the race that when a socket is closed, it will should call
the unbind, but if the family is removed at the same time the unbind
will not find it, leading to the warning. The real problem though is
that in this case the unbind could actually find a new family that is
registered to have a multicast group with the same ID, and call its
mcast_unbind() leading to confusing.
Also remove the warning since it would still trigger, but is now no
longer a problem.
This also moves the code in af_netlink.c to before unreferencing the
module to avoid having the same problem in the normal non-genl case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Layton reported that he could trigger the multicast unbind warning
in generic netlink using trinity. I originally thought it was a race
condition between unregistering the generic netlink family and closing
the socket, but there's a far simpler explanation: genetlink currently
allows subscribing to groups that don't (yet) exist, and the warning is
triggered when unsubscribing again while the group still doesn't exist.
Originally, I had a warning in the subscribe case and accepted it out of
userspace API concerns, but the warning was of course wrong and removed
later.
However, I now think that allowing userspace to subscribe to groups that
don't exist is wrong and could possibly become a security problem:
Consider a (new) genetlink family implementing a permission check in
the mcast_bind() function similar to the like the audit code does today;
it would be possible to bypass the permission check by guessing the ID
and subscribing to the group it exists. This is only possible in case a
family like that would be dynamically loaded, but it doesn't seem like a
huge stretch, for example wireless may be loaded when you plug in a USB
device.
To avoid this reject such subscription attempts.
If this ends up causing userspace issues we may need to add a workaround
in af_netlink to deny such requests but not return an error.
Reported-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel-doc for the parallel_ops family struct member is
missing, add it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
softnet_data.input_pkt_queue is protected by a spinlock that
we must hold when transferring packets from victim queue to an active
one. This is because other cpus could still be trying to enqueue packets
into victim queue.
A second problem is that when we transfert the NAPI poll_list from
victim to current cpu, we absolutely need to special case the percpu
backlog, because we do not want to add complex locking to protect
process_queue : Only owner cpu is allowed to manipulate it, unless cpu
is offline.
Based on initial patch from Prasad Sodagudi & Subash Abhinov
Kasiviswanathan.
This version is better because we do not slow down packet processing,
only make migration safer.
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Reported-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On dm816x we have two emac controllers with separate memory
areas.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some devices like dm816x have the MDIO registers within the first EMAC
instance address space. Let's fix the issue by allowing to pass an
optional second IO range for the EMAC control register area.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like the phy_id is never set up beyond getting the phandle.
Note that we can remove the ifdef for phy_node as there is a stub
for of_phy_connec() if CONFIG_OF is not set.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only use clk_get() to get the frequency, the rest is done by
the runtime PM calls. Let's free the clock too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ba97381343b ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On davinci_emac, we have pulse interrupts. This means that we need to
clear the EOI bits when disabling interrupts as otherwise the interrupts
keep happening. And we also need to not clear the EOI bits again when
enabling the interrupts as otherwise we will get tons of:
unexpected IRQ trap at vector 00
These errors almost certainly mean that the omap-intc.c is signaling
a spurious interrupt with the reserved irq 127 as we've seen earlier
on omap3.
Let's fix the issue by clearing the EOI bits when disabling the
interrupts. Let's also keep the comment for "Rx Threshold and Misc
interrupts are not enabled" for both enable and disable so people
are aware of this when potentially adding more support.
Note that eventually we should handle the RX and TX interrupts
separately like cpsw is now doing. However, so far I have not seen
any issues with this based on my testing, so it seems to behave a
little different compared to the cpsw that had a similar issue.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sockaddr is returned in IP(V6)_RECVERR as part of errhdr. That
structure is defined and allocated on the stack as
struct {
struct sock_extended_err ee;
struct sockaddr_in(6) offender;
} errhdr;
The second part is only initialized for certain SO_EE_ORIGIN values.
Always initialize it completely.
An MTU exceeded error on a SOCK_RAW/IPPROTO_RAW is one example that
would return uninitialized bytes.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Also verified that there is no padding between errhdr.ee and
errhdr.offender that could leak additional kernel data.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Except for VXLAN steering rules, all offloads should work as they were
under plain DMFS mode. Fix that by enabling all the offloads under
DMFS-A0 mode, except for VXLAN steering rules.
Fixes: d57febe1a478 "net/mlx4: Add A0 hybrid steering"
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes double kfree() calls at init_rx_ring() because
it causes static checker warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the MAC address is provided in the device tree file, the
condition is true and kernel crashes due to NULL dereference.
Signed-off-by: Girish K.S <ks.giri@samsung.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit b284fbe3b3ef9cf8 ("sh_eth: Fix access to TRSCER register") wanted
to add a .trscer_err_mask value to the R-Car Gen2 family-specific data
structure (r8a779x_data), but it was accidentally added to the
SH7724-specific data structure (sh7724_data).
Presumably this happened due to a patch conflict with commit
d407bc0203539031 ("sh-eth: Set fdr_value of R-Car SoCs"), which added
another field at the same position.
Move the field setting to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: b284fbe3b3ef9cf8 ("sh_eth: Fix access to TRSCER register")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
while adding vlan in dual EMAC mode, only specific ports should be
subscribed for the vlan, else it will lead to switching mode and
if both ports connected to same switch cpsw will hung as it creates
a network loop. Fixing this by adding only specific ports in case
of dual EMAC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not touch the packet after a netif_rx: it might
get freed behind our back.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Finally there will be three types of CAN FD controllers in the future:
1. ISO compliant (fixed)
2. non-ISO compliant (fixed, like the M_CAN IP v3.0.1 in m_can.c)
3. ISO/non-ISO CAN FD controllers (switchable, like the PEAK USB FD)
So the current M_CAN driver for the M_CAN IP v3.0.1 has to expose its non-ISO
implementation by setting the CAN_CTRLMODE_FD_NON_ISO ctrlmode at startup.
As this bit cannot be switched at configuration time CAN_CTRLMODE_FD_NON_ISO
must not be set in ctrlmode_supported of the current M_CAN driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The linux-can upstream git repositories are now hosted on kernel.org, update
MAINTAINERS accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Other tunnels like GRE break while VxLAN offloads are enabled in Skyhawk-R. To
avoid this, we should restrict offload features on a per-packet basis in such
conditions.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00df3a1955441 ("team: add peer notification")
Fixes: 492b200efdd20b8fcfd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.
Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.
Fixes: 05da589 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tracked-down-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For example, one could conceivably call
for_each_netdev_in_bond_rcu(condition ? bond1 : bond2, slave)
and get an unexpected result.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:
net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'
This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting base_reachable_time or base_reachable_time_ms on a
specific interface through sysctl or netlink, the reachable_time
value is not updated.
This means that neighbour entries will continue to be updated using the
old value until it is recomputed in neigh_period_work (which
recomputes the value every 300*HZ).
On systems with HZ equal to 1000 for instance, it means 5mins before
the change is effective.
This patch changes this behavior by recomputing reachable_time after
each set on base_reachable_time or base_reachable_time_ms.
The new value will become effective the next time the neighbour's timer
is triggered.
Changes are made in two places: the netlink code for set and the sysctl
handling code. For sysctl, I use a proc_handler. The ipv6 network
code does provide its own handler but it already refreshes
reachable_time correctly so it's not an issue.
Any other user of neighbour which provide its own handlers must
refresh reachable_time.
Signed-off-by: Jean-Francois Remy <jeff@melix.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In netfront the Rx and Tx path are independent and use different
locks. The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled. Since both sides use the same stats lock,
a deadlock may occur.
[ INFO: possible irq lock inversion dependency detected ]
3.16.2 #16 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
xennet_tx_interrupt+0x14/0x34
but this lock took another, HARDIRQ-unsafe lock in the past:
(&stat->syncp.seq#2){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&stat->syncp.seq#2);
local_irq_disable();
lock(&(&queue->tx_lock)->rlock);
lock(&stat->syncp.seq#2);
<Interrupt>
lock(&(&queue->tx_lock)->rlock);
Using separate locks for the Rx and Tx stats fixes this deadlock.
Reported-by: Dmitry Piotrovsky <piotrovskydmitry@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]
This bug was introduced by commit 588a6a99286ae30afb1339d8bc2163517b1b7dd1
("leds: netxbig: fix attribute-creation race").
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # 3.17+
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
In commit 5ad24def21b205a8 ("cxgb4vf: Fix ethtool get_settings for VF driver")
mdio_addr of port_info structure was used unininitialzed. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Feedback has shown that WRITE_ONCE(x, val) is easier to use than
ASSIGN_ONCE(val,x).
There are no in-tree users yet, so lets change it for 3.19.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
Corrected the comment describing the ndo operations to
reflect the actual prototype for couple of operations
Signed-off-by: B Viswanath <marichika4@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 0efaa7e82f02fe69c05ad28e905f31fc86e6f08e
locks: generic_delete_lease doesn't need a file_lock at all
moves the call to fl->fl_lmops->lm_change() to a place in the
code where fl might be a non-lease lock.
When that happens, fl_lmops is NULL and an Oops ensures.
So add an extra test to restore correct functioning.
Reported-by: Linda Walsh <suse@tlinx.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=912569
Cc: stable@vger.kernel.org (v3.18)
Fixes: 0efaa7e82f02fe69c05ad28e905f31fc86e6f08e
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
|
|
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
When batching up address ranges for TLB invalidation, we check tlb->end
!= 0 to indicate that some pages have actually been unmapped.
As of commit f045bbb9fa1b ("mmu_gather: fix over-eager
tlb_flush_mmu_free() calling"), we use the same check for freeing these
pages in order to avoid a performance regression where we call
free_pages_and_swap_cache even when no pages are actually queued up.
Unfortunately, the range could have been reset (tlb->end = 0) by
tlb_end_vma, which has been shown to cause memory leaks on arm64.
Furthermore, investigation into these leaks revealed that the fullmm
case on task exit no longer invalidates the TLB, by virtue of tlb->end
== 0 (in 3.18, need_flush would have been set).
This patch resolves the problem by reverting commit f045bbb9fa1b, using
instead tlb->local.nr as the predicate for page freeing in
tlb_flush_mmu_free and ensuring that tlb->end is initialised to a
non-zero value in the fullmm case.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Hauke Mehrtens
Ben Hutchings
Hagen Paul Pfeifer
Daniel Borkmann
Johannes Berg
Eric Dumazet
Tony Lindgren
Willem de Bruijn
Or Gerlitz
Byungho An
Girish K.S
Geert Uytterhoeven
Mugunthan V N
Ahmed S. Darwish
Roger Quadros
Oliver Hartkopp
Marc Kleine-Budde
Sriharsha Basavapatna
Prashant Sreedharan
Jiri Pirko
Thomas Graf
Vasu Dev
Hariprasad Shenai
Benjamin Poirier
Arnd Bergmann
Jean-Francois Remy
Stefan Agner
David Vrabel
Simon Guinot
Christian Borntraeger
B Viswanath
NeilBrown
Jan Beulich
Will Deacon