| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Adds watchdog device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17729/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Adds wake-up timer device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17728/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Adds power management nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17727/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Expand the MIPS Makefile help text to list generic board names, generic
defconfigs, and legacy defconfigs which have been converted to generic
and are still usable.
Here's a snippet of the new "make ARCH=mips help" output:
...
If you are targeting a system supported by generic kernels you may
configure the kernel for a given architecture target like so:
{micro32,32,64}{r1,r2,r6}{el,}_defconfig <BOARDS="list of boards">
Where BOARDS is some subset of the following:
boston
ni169445
ranchu
sead-3
xilfpga
Specifically the following generic default configurations are
supported:
32r1_defconfig - Build generic kernel for MIPS32 r1
32r1el_defconfig - Build generic kernel for MIPS32 r1 little endian
32r2_defconfig - Build generic kernel for MIPS32 r2
32r2el_defconfig - Build generic kernel for MIPS32 r2 little endian
32r6_defconfig - Build generic kernel for MIPS32 r6
32r6el_defconfig - Build generic kernel for MIPS32 r6 little endian
64r1_defconfig - Build generic kernel for MIPS64 r1
64r1el_defconfig - Build generic kernel for MIPS64 r1 little endian
64r2_defconfig - Build generic kernel for MIPS64 r2
64r2el_defconfig - Build generic kernel for MIPS64 r2 little endian
64r6_defconfig - Build generic kernel for MIPS64 r6
64r6el_defconfig - Build generic kernel for MIPS64 r6 little endian
micro32r2_defconfig - Build generic kernel for microMIPS32 r2
micro32r2el_defconfig - Build generic kernel for microMIPS32 r2 little endian
The following legacy default configurations have been converted to
generic and can still be used:
sead3_defconfig - Build 32r2el_defconfig BOARDS=sead-3
sead3micro_defconfig - Build micro32r2el_defconfig BOARDS=sead-3
xilfpga_defconfig - Build 32r2el_defconfig BOARDS=xilfpga
...
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18598/
|
|
Define legacy defconfigs which have been converted to the generic
platform more programatically, so that they can be listed in the
Makefile help text and as a separate Makefile target without
duplication.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18596/
|
|
Enable the crc32-mips module on MIPS generic r6 configs, where the
required MIPS r6 CRC instructions may be available.
As well as allowing the CRC instructions to be utilised, this should
also ensure the module gets some build coverage.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Marcin Nowakowski <marcin.nowakowski@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18602/
|
|
This module registers crc32 and crc32c algorithms that use the
optional CRC32[bhwd] and CRC32C[bhwd] instructions in MIPSr6 cores.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Patchwork: https://patchwork.linux-mips.org/patch/18601/
[jhogan@kernel.org: Add CRYPTO_ALG_OPTIONAL_KEY flag on Eric Biggers'
suggestion, due to commit a208fa8f3303 ("crypto: hash - annotate
algorithms taking optional key") in v4.16-rc1]
|
|
Indicate that CRC32 and CRC32C instuctions are supported by the CPU
through elf_hwcap flags.
This will be used by a follow-up commit that introduces crc32(c) crypto
acceleration modules and is required by GENERIC_CPU_AUTOPROBE feature.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18600/
|
|
Rewrite the comparison in `else if` statement, case where `min_low_pfn >
ARCH_PFN_OFFSET` has already been checked in the first `if` statement:
if (min_low_pfn > ARCH_PFN_OFFSET) {
Fix non-fatal warning during compilation using W=1:
arch/mips/kernel/setup.c: In function ‘bootmem_init’:
arch/mips/kernel/setup.c:461:25: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
} else if (min_low_pfn < ARCH_PFN_OFFSET) {
^
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18176/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Fix non-fatal warning during compilation using W=1:
arch/mips/kernel/setup.c:158:13: warning: no previous prototype for ‘memory_region_available’ [-Wmissing-prototypes]
bool __init memory_region_available(phys_addr_t start, phys_addr_t size)
^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18175/
[jhogan@kernel.org: tweak whitespace]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The unit name was 8c00000 but since the reg property is declared as:
reg = <0x0 0x4c00000 0x1 0xfb400000>;
the unit name should have been instead 4c00000.
Tested on MIPS Creator CI20 (v1):
$ cat /sys/firmware/devicetree/.../partitions/partition@4c00000/label;echo
system
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18529/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18528/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18008/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18007/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18006/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17920/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Enable CONFIG_SOC_BRCMSTB in bmips_stb_defconfig. CONFIG_BRCMSTB_PM is
also enabled by default option in Kconfig.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Reviewed-by: James Hogan <jhogan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/18590/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Using a period after a newline causes bad output.
Fixes: 64b139f97c01 ("MIPS: OCTEON: irq: add CIB and other fixes")
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17886/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
|
|
Passive sockets can have ongoing operations on them, specifically, we
have two wait_event_interruptable calls in pvcalls_front_accept.
Add two wake_up calls in pvcalls_front_release, then wait for the
potential waiters to return and release the sock_mapping refcount.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The kernel panics on PV domains because native_smp_cpus_done() is
only called for HVM domains.
Calculate __max_logical_packages for PV domains.
Fixes: b4c0a7326f5d ("x86/smpboot: Fix __max_logical_packages estimate")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Tested-and-reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: xen-devel@lists.xenproject.org
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Cc: <stable@vger.kernel.org> # 4.11
Fixes: fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent xenstore accesses")
Reported-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In many cases, page tables can be accessed concurrently by either another
CPU (due to things like fast gup) or by the hardware page table walker
itself, which may set access/dirty bits. In such cases, it is important
to use READ_ONCE/WRITE_ONCE when accessing page table entries so that
entries cannot be torn, merged or subject to apparent loss of coherence
due to compiler transformations.
Whilst there are some scenarios where this cannot happen (e.g. pinned
kernel mappings for the linear region), the overhead of using READ_ONCE
/WRITE_ONCE everywhere is minimal and makes the code an awful lot easier
to reason about. This patch consistently uses these macros in the arch
code, as well as explicitly namespacing pointers to page table entries
from the entries themselves by using adopting a 'p' suffix for the former
(as is sometimes used elsewhere in the kernel source).
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We get a warning about some slow configurations in randconfig kernels:
mm/memory.c:83:2: error: #warning Unfortunate NUMA and NUMA Balancing config, growing page-frame for last_cpupid. [-Werror=cpp]
The warning is reasonable by itself, but gets in the way of randconfig
build testing, so I'm hiding it whenever CONFIG_COMPILE_TEST is set.
The warning was added in 2013 in commit 75980e97dacc ("mm: fold
page->_last_nid into page->flags where possible").
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org (v3.14+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>,
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The pr_debug() in gic-v3 gic_send_sgi() can trigger a circular locking
warning:
GICv3: CPU10: ICC_SGI1R_EL1 5000400
======================================================
WARNING: possible circular locking dependency detected
4.15.0+ #1 Tainted: G W
------------------------------------------------------
dynamic_debug01/1873 is trying to acquire lock:
((console_sem).lock){-...}, at: [<0000000099c891ec>] down_trylock+0x20/0x4c
but task is already holding lock:
(&rq->lock){-.-.}, at: [<00000000842e1587>] __task_rq_lock+0x54/0xdc
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&rq->lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock+0x4c/0x60
task_fork_fair+0x3c/0x148
sched_fork+0x10c/0x214
copy_process.isra.32.part.33+0x4e8/0x14f0
_do_fork+0xe8/0x78c
kernel_thread+0x48/0x54
rest_init+0x34/0x2a4
start_kernel+0x45c/0x488
-> #1 (&p->pi_lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
try_to_wake_up+0x48/0x600
wake_up_process+0x28/0x34
__up.isra.0+0x60/0x6c
up+0x60/0x68
__up_console_sem+0x4c/0x7c
console_unlock+0x328/0x634
vprintk_emit+0x25c/0x390
dev_vprintk_emit+0xc4/0x1fc
dev_printk_emit+0x88/0xa8
__dev_printk+0x58/0x9c
_dev_info+0x84/0xa8
usb_new_device+0x100/0x474
hub_port_connect+0x280/0x92c
hub_event+0x740/0xa84
process_one_work+0x240/0x70c
worker_thread+0x60/0x400
kthread+0x110/0x13c
ret_from_fork+0x10/0x18
-> #0 ((console_sem).lock){-...}:
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
other info that might help us debug this:
Chain exists of:
(console_sem).lock --> &p->pi_lock --> &rq->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&rq->lock);
lock(&p->pi_lock);
lock(&rq->lock);
lock((console_sem).lock);
*** DEADLOCK ***
2 locks held by dynamic_debug01/1873:
#0: (&p->pi_lock){-.-.}, at: [<000000001366df53>] wake_up_new_task+0x40/0x470
#1: (&rq->lock){-.-.}, at: [<00000000842e1587>] __task_rq_lock+0x54/0xdc
stack backtrace:
CPU: 10 PID: 1873 Comm: dynamic_debug01 Tainted: G W 4.15.0+ #1
Hardware name: GIGABYTE R120-T34-00/MT30-GS2-00, BIOS T48 10/02/2017
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x2c
dump_stack+0xa4/0xe0
print_circular_bug.isra.31+0x29c/0x2b8
check_prev_add.constprop.39+0x6c8/0x6dc
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
GICv3: CPU0: ICC_SGI1R_EL1 12000
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc: ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq(): ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Some versions of QEMU will produce an ibm,dynamic-reconfiguration-memory
node with a ibm,dynamic-memory property that is zero-filled. This
causes the drmem code to oops trying to parse this property.
The fix for this is to validate that the property does contain LMB
entries before trying to parse it and bail if the count is zero.
Oops: Kernel access of bad area, sig: 11 [#1]
DAR: 0000000000000010
NIP read_drconf_v1_cell+0x54/0x9c
LR read_drconf_v1_cell+0x48/0x9c
Call Trace:
__param_initcall_debug+0x0/0x28 (unreliable)
drmem_init+0x144/0x2f8
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x298/0x38c
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0xb4
The ibm,dynamic-reconfiguration-memory device tree property generated
that causes this:
ibm,dynamic-reconfiguration-memory {
ibm,lmb-size = <0x0 0x10000000>;
ibm,memory-flags-mask = <0xff>;
ibm,dynamic-memory = <0x0 0x0 0x0 0x0 0x0 0x0>;
linux,phandle = <0x7e57eed8>;
ibm,associativity-lookup-arrays = <0x1 0x4 0x0 0x0 0x0 0x0>;
ibm,memory-preservation-time = <0x0>;
};
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Tested-by: Daniel Black <daniel@linux.vnet.ibm.com>
[mpe: Trim oops report]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michael Kelley <mhkelley@outlook.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kys@microsoft.com
Cc: martin.petersen@oracle.com
Cc: mikelley@microsoft.com
Fixes: c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()")
Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The X86_P6_NOP config class leaves out many i686-class CPUs. Instead,
explicitly enumerate all these CPUs.
Using a configuration with M686 currently sets X86_MINIMUM_CPU_FAMILY=5
instead of the correct value of 6.
Booting on an i586 it will fail to generate the "This kernel
requires an i686 CPU, but only detected an i586 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i686-specific instructions.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-3-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
i586-class machines also lack support for Physical Address Extension (PAE),
so add them to the exclusion list.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-2-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Several i586-class CPUs supporting this instruction are missing from
the X86_CMPXCHG64 config group.
Using a configuration with either M586TSC or M586MMX currently sets
X86_MINIMUM_CPU_FAMILY=4 instead of the correct value of 5.
Booting on an i486 it will fail to generate the "This kernel
requires an i586 CPU, but only detected an i486 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i586-specific instructions.
The M586 CPU is not in this list because at least the Cyrix 5x86
lacks this instruction, and perhaps others.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-1-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Improve error handling when disarming ftrace-based kprobes. Like with
arm_kprobe_ftrace(), propagate any errors from disarm_kprobe_ftrace() so
that we do not disable/unregister kprobes that are still armed. In other
words, unregister_kprobe() and disable_kprobe() should not report success
if the kprobe could not be disarmed.
disarm_all_kprobes() keeps its current behavior and attempts to
disarm all kprobes. It returns the last encountered error and gives a
warning if not all probes could be disarmed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-3-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Improve error handling when arming ftrace-based kprobes. Specifically, if
we fail to arm a ftrace-based kprobe, register_kprobe()/enable_kprobe()
should report an error instead of success. Previously, this has lead to
confusing situations where register_kprobe() would return 0 indicating
success, but the kprobe would not be functional if ftrace registration
during the kprobe arming process had failed. We should therefore take any
errors returned by ftrace into account and propagate this error so that we
do not register/enable kprobes that cannot be armed. This can happen if,
for example, register_ftrace_function() finds an IPMODIFY conflict (since
kprobe_ftrace_ops has this flag set) and returns an error. Such a conflict
is possible since livepatches also set the IPMODIFY flag for their ftrace_ops.
arm_all_kprobes() keeps its current behavior and attempts to arm all
kprobes. It returns the last encountered error and gives a warning if
not all probes could be armed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-2-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The recently introduced clock gate support breaks on Tegra chips because
no thermal support is enabled for those devices. Conditionalize the code
on the existence of thermal support to fix this.
Fixes: b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1")
Cc: Martin Peres <martin.peres@free.fr>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
|
|
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
|
|
Update comment typo _consisitent_ to _consistent_ from following commit.
commit 0206319fdfee ("blk-mq: Fix poll_stat for new size-based bucketing.")
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit f120c7b187e6c418238710b48723ce141f467543 which is no
longer required with the introduction of a syscall.tbl on s390.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference: 1518090470-2899-2-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-q1lg0nvhha1tk39ri9aqalcb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Recently, s390 uses a syscall.tbl input file to generate its system call
table and unistd uapi header files. Hence, update mksyscalltbl to use
it as input to create the system table for perf.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference: 1518090470-2899-4-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-bdyhllhsq1zgxv2qx4m377y6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
Jaedon Shin
James Hogan
Marcin Nowakowski
Mathieu Malaterre
Arvind Yadav
Pravin Shedge
Joe Perches
Linus Torvalds
Stefano Stabellini
Prarit Bhargava
Joao Martins
Robin Murphy
Will Deacon
Arnd Bergmann
NeilBrown
Andy Shevchenko
Marc Zyngier
Stephen Boyd
Shanker Donthineni
Mark Salter
Matt Redfearn
Nathan Fontenot
Michael Kelley
Matthew Whitehead
Jessica Yu
Thierry Reding
Minwoo Im
Hendrik Brueckner