| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323112613.7550-3-cai.huoqing@linux.dev
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323112613.7550-2-cai.huoqing@linux.dev
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323112613.7550-1-cai.huoqing@linux.dev
|
|
Firmwares advertising the support of triggering 11d algorithm on the
scan results of a regular scan expects driver to send
WMI_11D_SCAN_START_CMDID before sending WMI_START_SCAN_CMDID.
Triggering 11d algorithm on the scan results of a normal scan helps
in completely avoiding a separate 11d scan for determining regdomain.
This indirectly helps in speeding up connections on station
interfaces on the chipsets supporting 11D scan.
To enable this feature, send WMI_11D_SCAN_START_CMDID just before
sending WMI_START_SCAN_CMDID if the firmware advertises
WMI_TLV_SERVICE_SUPPORT_11D_FOR_HOST_SCAN service flag.
WCN6750 & WCN6855 supports this feature.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315161817.29627-1-quic_mpubbise@quicinc.com
|
|
While initializing spectral, the magic value is getting written to the
invalid memory address leading to random boot-up crash. This occurs
due to the incorrect index increment in ath11k_dbring_fill_magic_value
function. Fix it by replacing the existing logic with memset32 to ensure
there is no invalid memory access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Fixes: d3d358efc553 ("ath11k: add spectral/CFR buffer validation support")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230321052900.16895-1-quic_ppranees@quicinc.com
|
|
The WMI management rx event has multiple arrays of TLVs, however the common
WMI TLV parser won't handle multiple TLV tags of same type.
So the multiple array tags of WMI management rx TLV is parsed incorrectly
and the length calculated becomes wrong when the target sends multiple
array tags.
Add separate TLV parser to handle multiple arrays for WMI management rx
TLV. This fixes invalid length issue when the target sends multiple array
tags.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320133840.30162-1-quic_nmaran@quicinc.com
|
|
In QCN9074, station dump signal values display default value which
is -95 dbm, since there is firmware header change for HAL_RX_MPDU_START
between QCN9074 and IPQ8074 which cause wrong peer_id fetch from msdu.
Fix this by updating hal_rx_mpdu_info with corresponding QCN9074 tlv
format.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320110312.20639-1-quic_ppranees@quicinc.com
|
|
Fine Time Measurement(FTM) is offloaded feature to firmware.
Hence, the configuration of FTM responder role is done using
firmware capability flag instead of hw param.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317072034.8217-1-quic_gjothira@quicinc.com
|
|
Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.
Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.
WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.
In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).
With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323060913.10097-1-quic_mpubbise@quicinc.com
|
|
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
drivers/net/wireless/ath/carl9170/tx.c:702:61: warning: array subscript i is outside array bounds of ‘const struct _carl9170_tx_status[0]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/tx.c:701:65: warning: array subscript i is outside array bounds of ‘const struct _carl9170_tx_status[0]’ [-Warray-bounds=]
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/267
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ZBSl2M+aGIO1fnuG@work
|
|
GCC (and Clang)[1] does not like having a partially allocated object,
since it cannot reason about it for bounds checking. Instead, fully
allocate struct carl9170_cmd.
Fix the following warnings Seen under GCC 13:
drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[4]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[4]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:161:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:162:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:163:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:164:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=]
drivers/net/wireless/ath/carl9170/cmd.c:220:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=]
Link: https://github.com/KSPP/linux/issues/268
Link: godbolt.org/z/KP97sxh3T [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ZBSjx236+BTiRByf@work
|
|
clang with W=1 reports:
drivers/net/wireless/ath/ath10k/ce.c:88:1: error:
unused function 'ath10k_get_ring_byte' [-Werror,-Wunused-function]
ath10k_get_ring_byte(unsigned int offset,
^
This function is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230322122855.2570417-1-trix@redhat.com
|
Cai Huoqing
Manikanta Pubbisetty
P Praneesh
Bhagavathi Perumal S
Ganesh Babu Jothiram
Gustavo A. R. Silva
Tom Rix