| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Make the link between the core macros and the datasheet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
W25N01JW and W25N02JW use a different technology with higher frequencies
supported (up to 166MHz). There is one drawback though, the slowest
READ_FROM_CACHE command cannot run above 54MHz. Because of that, we need
to set a limit for these chips on the basic READ_FROM_CACHE variant.
Duplicating this list is not a problem because these chips have DTR
support, and the list of supported variants will diverge from all the
other chips when adding support for it.
Cc: stable+noautosel@kernel.org # New feature being added
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Advanced SPI-NAND chips are capable of reading data much faster by
leveraging DTR support. This support extends to dual and quad
configurations.
Create macros defining all possible read from cache DTR variants:
- SPINAND_PAGE_READ_FROM_CACHE_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X2_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X4_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_DUALIO_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_QUADIO_DTR_OP
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
and per operation maximum frequencies, this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot, the extra computing needed
compared to the previous version is acceptable wrt. the expected
improvements.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
While the SPINAND_PAGE_READ_FROM_CACHE_FAST_OP macro is supposed to be
able to run at the flash highest supported frequency, it is not the case
of the regular read from cache, which may be limited in terms of maximum
frequency. Add an optional argument to this macro, which will be used to
set the maximum frequency, if any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
After commit e6204f39fe3a ("spi: amd: Drop redundant check"), clang warns (or
errors with CONFIG_WERROR=y):
drivers/spi/spi-amd.c:695:9: error: variable 'ret' is uninitialized when used here [-Werror,-Wuninitialized]
695 | return ret;
| ^~~
drivers/spi/spi-amd.c:673:9: note: initialize the variable 'ret' to silence this warning
673 | int ret;
| ^
| = 0
1 error generated.
ret is no longer set on anything other than the default switch path.
Replace ret with a direct return of 0 at the end of the function and
-EOPNOTSUPP in the default case to resolve the warning.
Fixes: e6204f39fe3a ("spi: amd: Drop redundant check")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501112315.ugYQ7Ce7-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250111-spi-amd-fix-uninitialized-ret-v1-1-c66ab9f6a23d@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the SPI-NAND layer, we currently make list of operation variants from
the fastest one to the slowest and there is a bit of logic in the core
to go over them and pick the first one that is supported by the
controller, ie. the fastest one among the supported ops.
This kind of logic only works if all operations run at the same
frequency, but as soon as we introduce per operation max frequencies it
is not longer as obvious which operation will be faster, especially
since it also depends on the PCB/controller frequency limitation.
One way to make this choice more clever is to go over all the
variants and for each of them derive an indicator which will help derive
the theoretical best. In this case, we derive a theoretical duration for
the entire operation and we take the smallest one.
Add a helper that parses the spi-mem operation and returns this value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250110-winbond-6-11-rc1-quad-support-v3-20-7ab4bd56cf6e@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We do have macros for defining command, address, dummy and data
cycles. We also have a .dtr flag that implies sampling the bus on both
edges, but there are currently no macros enabling it. We might make use
of such macros, so let's create:
- SPI_MEM_DTR_OP_CMD
- SPI_MEM_DTR_OP_ADDR
- SPI_MEM_DTR_OP_DUMMY
- SPI_MEM_DTR_OP_DATA_OUT
- SPI_MEM_DTR_OP_DATA_OUT
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-19-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the order in which all the `struct spi_mem_op` members are
defined.
This is purely aesthetics, there is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-18-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-17-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-16-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-15-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-14-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Han Xu <han.xu@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Cc: Yogesh Gaur <yogeshgaur.83@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-13-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-12-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-11-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-10-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
This controller however performed a frequency check, which is also
observed during the ->check_op() phase.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Conor Dooley <conor.dooley@microchip.com>
Cc: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-9-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-8-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-7-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-6-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-5-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both spi and spi-mem cores already take care of checking the minimum and
maximum speed for transfers depending on the controller
capabilities. There is no reason to repeat this check in controller
drivers.
Once this possible error condition removed from the function, it makes
no longer sense to return an int.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-4-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
This controller however performed a frequency check, which is also
observed during the ->check_op() phase.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-3-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are spi devices with multiple frequency limitations depending on
the invoked command. We probably do not want to afford running at the
lowest supported frequency all the time, so if we want to get the most
of our hardware, we need to allow per-operation frequency limitations.
Among all the SPI memory controllers, I believe all are capable of
changing the spi frequency on the fly. Some of the drivers do not make
any frequency setup though. And some others will derive a per chip
prescaler value which will be used forever.
Actually changing the frequency on the fly is something new in Linux, so
we need to carefully flag the drivers which do and do not support it. A
controller capability is created for that, and the presence for this
capability will always be checked before accepting such pattern.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-2-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix a buffer overflow issue in qcom_clear_bam_transaction by using
struct_group to group related fields and avoid FORTIFY_SOURCE warnings.
On x86 architecture, the following error occurs due to warnings being
treated as errors:
In function ‘fortify_memset_chk’,
inlined from ‘qcom_clear_bam_transaction’ at
drivers/mtd/nand/qpic_common.c:88:2:
./include/linux/fortify-string.h:480:25: error: call to ‘__write_overflow_field’
declared with attribute warning: detected write beyond size of field
(1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LD [M] drivers/mtd/nand/nandcore.o
CC [M] drivers/w1/masters/mxc_w1.o
cc1: all warnings being treated as errors
This patch addresses the issue by grouping the related fields in
struct bam_transaction using struct_group and updating the memset call
accordingly.
Fixes: 8c52932da5e6 ("mtd: rawnand: qcom: cleanup qcom_nandc driver")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
|
|
The Arch Linux glibc package contains a versioned dependency on
"linux-api-headers". If the linux-api-headers package provided by
pacman-pkg does not specify an explicit version this dependency is not
satisfied.
Fix the dependency by providing an explicit version.
Fixes: c8578539deba ("kbuild: add script and target to generate pacman package")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
For non-pollable files, buffer ring consumption will commit upfront.
This is fine, but io_ring_buffer_select() will return the address of the
buffer after having committed it. For incrementally consumed buffers,
this is incorrect as it will modify the buffer address.
Store the pre-committed value and return that. If that isn't done, then
the initial part of the buffer is not used and the application will
correctly assume the content arrived at the start of the userspace
buffer, but the kernel will have put it later in the buffer. Or it can
cause a spurious -EFAULT returned in the CQE, depending on the buffer
size. As bounds are suitably checked for doing the actual IO, no adverse
side effects are possible - it's just a data misplacement within the
existing buffer.
Reported-by: Gwendal Fernet <gwendalfernet@gmail.com>
Cc: stable@vger.kernel.org
Fixes: ae98dbf43d75 ("io_uring/kbuf: add support for incremental buffer consumption")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Driver queries vport_cxt.num_plane and enables multiplane when it is
greater then 0, but some old FWs (versions from x.40.1000 till x.42.1000),
report vport_cxt.num_plane = 1 unexpectedly.
Fix it by querying num_plane only when HCA_CAP2.multiplane bit is set.
Fixes: 2a5db20fa532 ("RDMA/mlx5: Add support to multi-plane device and port")
Link: https://patch.msgid.link/r/1ef901acdf564716fcf550453cf5e94f343777ec.1734610916.git.leon@kernel.org
Cc: stable@vger.kernel.org
Reported-by: Francesco Poli <invernomuto@paranoici.org>
Closes: https://lore.kernel.org/all/nvs4i2v7o6vn6zhmtq4sgazy2hu5kiulukxcntdelggmznnl7h@so3oul6uwgbl/
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When ICSSG interfaces are brought down and brought up again, the
pru cores are shut down and booted again, flushing out all the memories
and start again in a clean state. Hence it is expected that the
IEP_CMP_CFG register needs to be flushed during iep_init() to ensure
that the existing residual configuration doesn't cause any unusual
behavior. If the register is not cleared, existing IEP_CMP_CFG set for
CMP1 will result in SYNC0_OUT signal based on the SYNC_OUT register values.
After bringing the interface up, calling PPS enable doesn't work as
the driver believes PPS is already enabled, (iep->pps_enabled is not
cleared during interface bring down) and driver will just return true
even though there is no signal. Fix this by disabling pps and perout.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0
and SLICE1. Currently whenever any ICSSG interface comes up we load the
respective firmwares to PRU cores and whenever interface goes down, we
stop the resective cores. Due to this, when SLICE0 goes down while
SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is
stopped. This results in clock jump for SLICE1 interface as the timesync
related operations are no longer running.
As there are interdependencies between SLICE0 and SLICE1 firmwares,
fix this by running both PRU0 and PRU1 firmwares as long as at least 1
ICSSG interface is up. Add new flag in prueth struct to check if all
firmwares are running and remove the old flag (fw_running).
Use emacs_initialized as reference count to load the firmwares for the
first and last interface up/down. Moving init_emac_mode and fw_offload_mode
API outside of icssg_config to icssg_common_start API as they need
to be called only once per firmware boot.
Change prueth_emac_restart() to return error code and add error prints
inside the caller of this functions in case of any failures.
Move prueth_emac_stop() from common to sr1 driver.
sr1 and sr2 drivers have different logic handling for stopping
the firmwares. While sr1 driver is dependent on emac structure
to stop the corresponding pru cores for that slice, for sr2
all the pru cores of both the slices are stopped and is not
dependent on emac. So the prueth_emac_stop() function is no
longer common and can be moved to sr1 driver.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the skb size after coalescing is only limited by the skb
layout (the skb must not carry frag_list). A single coalesced skb
covering several MSS can potentially fill completely the receive
buffer. In such a case, the snd win will zero until the receive buffer
will be empty again, affecting tput badly.
Fixes: 8268ed4c9d19 ("mptcp: introduce and use mptcp_try_coalesce()")
Cc: stable@vger.kernel.org # please delay 2 weeks after 6.13-final release
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-3-8608af434ceb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Under some corner cases the MPTCP protocol can end-up invoking
mptcp_cleanup_rbuf() when no data has been copied, but such helper
assumes the opposite condition.
Explicitly drop such assumption and performs the costly call only
when strictly needed - before releasing the msk socket lock.
Fixes: fd8976790a6c ("mptcp: be careful on MPTCP-level ack.")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-2-8608af434ceb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the recvmsg() blocks after receiving some data - i.e. due to
SO_RCVLOWAT - the MPTCP code will attempt multiple times to
adjust the receive buffer size, wrongly accounting every time the
cumulative of received data - instead of accounting only for the
delta.
Address the issue moving mptcp_rcv_space_adjust just after the
data reception and passing it only the just received bytes.
This also removes an unneeded difference between the TCP and MPTCP
RX code path implementation.
Fixes: 581302298524 ("mptcp: error out earlier on disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-1-8608af434ceb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot found a race in ila_add_mapping() [1]
commit 031ae72825ce ("ila: call nf_unregister_net_hooks() sooner")
attempted to fix a similar issue.
Looking at the syzbot repro, we have concurrent ILA_CMD_ADD commands.
Add a mutex to make sure at most one thread is calling nf_register_net_hooks().
[1]
BUG: KASAN: slab-use-after-free in rht_key_hashfn include/linux/rhashtable.h:159 [inline]
BUG: KASAN: slab-use-after-free in __rhashtable_lookup.constprop.0+0x426/0x550 include/linux/rhashtable.h:604
Read of size 4 at addr ffff888028f40008 by task dhcpcd/5501
CPU: 1 UID: 0 PID: 5501 Comm: dhcpcd Not tainted 6.13.0-rc4-syzkaller-00054-gd6ef8b40d075 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:489
kasan_report+0xd9/0x110 mm/kasan/report.c:602
rht_key_hashfn include/linux/rhashtable.h:159 [inline]
__rhashtable_lookup.constprop.0+0x426/0x550 include/linux/rhashtable.h:604
rhashtable_lookup include/linux/rhashtable.h:646 [inline]
rhashtable_lookup_fast include/linux/rhashtable.h:672 [inline]
ila_lookup_wildcards net/ipv6/ila/ila_xlat.c:127 [inline]
ila_xlat_addr net/ipv6/ila/ila_xlat.c:652 [inline]
ila_nf_input+0x1ee/0x620 net/ipv6/ila/ila_xlat.c:185
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xbb/0x200 net/netfilter/core.c:626
nf_hook.constprop.0+0x42e/0x750 include/linux/netfilter.h:269
NF_HOOK include/linux/netfilter.h:312 [inline]
ipv6_rcv+0xa4/0x680 net/ipv6/ip6_input.c:309
__netif_receive_skb_one_core+0x12e/0x1e0 net/core/dev.c:5672
__netif_receive_skb+0x1d/0x160 net/core/dev.c:5785
process_backlog+0x443/0x15f0 net/core/dev.c:6117
__napi_poll.constprop.0+0xb7/0x550 net/core/dev.c:6883
napi_poll net/core/dev.c:6952 [inline]
net_rx_action+0xa94/0x1010 net/core/dev.c:7074
handle_softirqs+0x213/0x8f0 kernel/softirq.c:561
__do_softirq kernel/softirq.c:595 [inline]
invoke_softirq kernel/softirq.c:435 [inline]
__irq_exit_rcu+0x109/0x170 kernel/softirq.c:662
irq_exit_rcu+0x9/0x30 kernel/softirq.c:678
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1049 [inline]
sysvec_apic_timer_interrupt+0xa4/0xc0 arch/x86/kernel/apic/apic.c:1049
Fixes: 7f00feaf1076 ("ila: Add generic ILA translation facility")
Reported-by: syzbot+47e761d22ecf745f72b9@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6772c9ae.050a0220.2f3838.04c7.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Tom Herbert <tom@herbertland.com>
Link: https://patch.msgid.link/20241230162849.2795486-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found
by syzbot.
Rework vlan_get_protocol_dgram() to not touch skb at all,
so that it can be used from many cpus on the same skb.
Add a const qualifier to skb argument.
[1]
skbuff: skb_under_panic: text:ffffffff8a8ccd05 len:29 put:14 head:ffff88807fc8e400 data:ffff88807fc8e3f4 tail:0x11 end:0x140 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 5892 Comm: syz-executor883 Not tainted 6.13.0-rc4-syzkaller-00054-gd6ef8b40d075 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0b 8d 48 c7 c6 86 d5 25 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 5a 69 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc900038d7638 EFLAGS: 00010282
RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 609ffd18ea660600
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88802483c8d0 R08: ffffffff817f0a8c R09: 1ffff9200071ae60
R10: dffffc0000000000 R11: fffff5200071ae61 R12: 0000000000000140
R13: ffff88807fc8e400 R14: ffff88807fc8e3f4 R15: 0000000000000011
FS: 00007fbac5e006c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fbac5e00d58 CR3: 000000001238e000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
vlan_get_protocol_dgram+0x165/0x290 net/packet/af_packet.c:585
packet_recvmsg+0x948/0x1ef0 net/packet/af_packet.c:3552
sock_recvmsg_nosec net/socket.c:1033 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1055
____sys_recvmsg+0x1c6/0x480 net/socket.c:2803
___sys_recvmsg net/socket.c:2845 [inline]
do_recvmmsg+0x426/0xab0 net/socket.c:2940
__sys_recvmmsg net/socket.c:3014 [inline]
__do_sys_recvmmsg net/socket.c:3037 [inline]
__se_sys_recvmmsg net/socket.c:3030 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3030
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 79eecf631c14 ("af_packet: Handle outgoing VLAN packets without hardware offloading")
Reported-by: syzbot+74f70bb1cb968bf09e4f@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6772c485.050a0220.2f3838.04c5.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chengen Du <chengen.du@canonical.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20241230161004.2681892-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found
by syzbot.
Rework vlan_get_tci() to not touch skb at all,
so that it can be used from many cpus on the same skb.
Add a const qualifier to skb argument.
[1]
skbuff: skb_under_panic: text:ffffffff8a8da482 len:32 put:14 head:ffff88807a1d5800 data:ffff88807a1d5810 tail:0x14 end:0x140 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 UID: 0 PID: 5880 Comm: syz-executor172 Not tainted 6.13.0-rc3-syzkaller-00762-g9268abe611b0 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:skb_panic net/core/skbuff.c:206 [inline]
RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216
Code: 0b 8d 48 c7 c6 9e 6c 26 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 3a 5a 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3
RSP: 0018:ffffc90003baf5b8 EFLAGS: 00010286
RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 8565c1eec37aa000
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffff88802616fb50 R08: ffffffff817f0a4c R09: 1ffff92000775e50
R10: dffffc0000000000 R11: fffff52000775e51 R12: 0000000000000140
R13: ffff88807a1d5800 R14: ffff88807a1d5810 R15: 0000000000000014
FS: 00007fa03261f6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd65753000 CR3: 0000000031720000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_push+0xe5/0x100 net/core/skbuff.c:2636
vlan_get_tci+0x272/0x550 net/packet/af_packet.c:565
packet_recvmsg+0x13c9/0x1ef0 net/packet/af_packet.c:3616
sock_recvmsg_nosec net/socket.c:1044 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1066
____sys_recvmsg+0x1c6/0x480 net/socket.c:2814
___sys_recvmsg net/socket.c:2856 [inline]
do_recvmmsg+0x426/0xab0 net/socket.c:2951
__sys_recvmmsg net/socket.c:3025 [inline]
__do_sys_recvmmsg net/socket.c:3048 [inline]
__se_sys_recvmmsg net/socket.c:3041 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3041
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
Fixes: 79eecf631c14 ("af_packet: Handle outgoing VLAN packets without hardware offloading")
Reported-by: syzbot+8400677f3fd43f37d3bc@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6772c485.050a0220.2f3838.04c6.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chengen Du <chengen.du@canonical.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20241230161004.2681892-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ipc_mmio_init() used the post-decrement operator in its loop continuing
condition of "retries" counter being "> 0", which meant that when this
condition caused loop exit "retries" counter reached -1.
But the later valid exec stage failure check only tests for "retries"
counter being exactly zero, so it didn't trigger in this case (but
would wrongly trigger if the code reaches a valid exec stage in the
very last loop iteration).
Fix this by using the pre-decrement operator instead, so the loop counter
is exactly zero on valid exec stage failure.
Fixes: dc0514f5d828 ("net: iosm: mmio scratchpad")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://patch.msgid.link/8b19125a825f9dcdd81c667c1e5c48ba28d505a6.1735490770.git.mail@maciej.szmigiero.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After blamed commit, crypto sockets could accidentally be destroyed
from RCU call back, as spotted by zyzbot [1].
Trying to acquire a mutex in RCU callback is not allowed.
Restrict SO_REUSEPORT socket option to inet sockets.
v1 of this patch supported TCP, UDP and SCTP sockets,
but fcnal-test.sh test needed RAW and ICMP support.
[1]
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:562
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 24, name: ksoftirqd/1
preempt_count: 100, expected: 0
RCU nest depth: 0, expected: 0
1 lock held by ksoftirqd/1/24:
#0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:337 [inline]
#0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_do_batch kernel/rcu/tree.c:2561 [inline]
#0: ffffffff8e937ba0 (rcu_callback){....}-{0:0}, at: rcu_core+0xa37/0x17a0 kernel/rcu/tree.c:2823
Preemption disabled at:
[<ffffffff8161c8c8>] softirq_handle_begin kernel/softirq.c:402 [inline]
[<ffffffff8161c8c8>] handle_softirqs+0x128/0x9b0 kernel/softirq.c:537
CPU: 1 UID: 0 PID: 24 Comm: ksoftirqd/1 Not tainted 6.13.0-rc3-syzkaller-00174-ga024e377efed #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
__might_resched+0x5d4/0x780 kernel/sched/core.c:8758
__mutex_lock_common kernel/locking/mutex.c:562 [inline]
__mutex_lock+0x131/0xee0 kernel/locking/mutex.c:735
crypto_put_default_null_skcipher+0x18/0x70 crypto/crypto_null.c:179
aead_release+0x3d/0x50 crypto/algif_aead.c:489
alg_do_release crypto/af_alg.c:118 [inline]
alg_sock_destruct+0x86/0xc0 crypto/af_alg.c:502
__sk_destruct+0x58/0x5f0 net/core/sock.c:2260
rcu_do_batch kernel/rcu/tree.c:2567 [inline]
rcu_core+0xaaa/0x17a0 kernel/rcu/tree.c:2823
handle_softirqs+0x2d4/0x9b0 kernel/softirq.c:561
run_ksoftirqd+0xca/0x130 kernel/softirq.c:950
smpboot_thread_fn+0x544/0xa30 kernel/smpboot.c:164
kthread+0x2f0/0x390 kernel/kthread.c:389
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
</TASK>
Fixes: 8c7138b33e5c ("net: Unpublish sk from sk_reuseport_cb before call_rcu")
Reported-by: syzbot+b3e02953598f447d4d2a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6772f2f4.050a0220.2f3838.04cb.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241231160527.3994168-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit disabled hardware offoad of IPv6 packets with
extension headers on devices that advertise NETIF_F_IPV6_CSUM,
based on the definition of that feature in skbuff.h:
* * - %NETIF_F_IPV6_CSUM
* - Driver (device) is only able to checksum plain
* TCP or UDP packets over IPv6. These are specifically
* unencapsulated packets of the form IPv6|TCP or
* IPv6|UDP where the Next Header field in the IPv6
* header is either TCP or UDP. IPv6 extension headers
* are not supported with this feature. This feature
* cannot be set in features for a device with
* NETIF_F_HW_CSUM also set. This feature is being
* DEPRECATED (see below).
The change causes skb_warn_bad_offload to fire for BIG TCP
packets.
[ 496.310233] WARNING: CPU: 13 PID: 23472 at net/core/dev.c:3129 skb_warn_bad_offload+0xc4/0xe0
[ 496.310297] ? skb_warn_bad_offload+0xc4/0xe0
[ 496.310300] skb_checksum_help+0x129/0x1f0
[ 496.310303] skb_csum_hwoffload_help+0x150/0x1b0
[ 496.310306] validate_xmit_skb+0x159/0x270
[ 496.310309] validate_xmit_skb_list+0x41/0x70
[ 496.310312] sch_direct_xmit+0x5c/0x250
[ 496.310317] __qdisc_run+0x388/0x620
BIG TCP introduced an IPV6_TLV_JUMBO IPv6 extension header to
communicate packet length, as this is an IPv6 jumbogram. But, the
feature is only enabled on devices that support BIG TCP TSO. The
header is only present for PF_PACKET taps like tcpdump, and not
transmitted by physical devices.
For this specific case of extension headers that are not
transmitted, return to the situation before the blamed commit
and support hardware offload.
ipv6_has_hopopt_jumbo() tests not only whether this header is present,
but also that it is the only extension header before a terminal (L4)
header.
Fixes: 04c20a9356f2 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Closes: https://lore.kernel.org/netdev/CANn89iK1hdC3Nt8KPhOtTF8vCPc1AHDCtse_BTNki1pWxAByTQ@mail.gmail.com/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250101164909.1331680-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In efx_tc_ct_zone_ht_params, the key_len was previously set to
offsetof(struct efx_tc_ct_zone, linkage). This calculation is incorrect
because it includes any padding between the zone field and the linkage
field due to structure alignment, which can vary between systems.
This patch updates key_len to use sizeof_field(struct efx_tc_ct_zone, zone)
, ensuring that the hash table correctly uses the zone as the key. This fix
prevents potential hash lookup errors and improves connection tracking
reliability.
Fixes: c3bb5c6acd4e ("sfc: functions to register for conntrack zone offload")
Signed-off-by: Liang Jie <liangjie@lixiang.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20241230093709.3226854-1-buaajxlj@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reports that ->msg_inq may get used uinitialized from the
following path:
BUG: KMSAN: uninit-value in io_recv_buf_select io_uring/net.c:1094 [inline]
BUG: KMSAN: uninit-value in io_recv+0x930/0x1f90 io_uring/net.c:1158
io_recv_buf_select io_uring/net.c:1094 [inline]
io_recv+0x930/0x1f90 io_uring/net.c:1158
io_issue_sqe+0x420/0x2130 io_uring/io_uring.c:1740
io_queue_sqe io_uring/io_uring.c:1950 [inline]
io_req_task_submit+0xfa/0x1d0 io_uring/io_uring.c:1374
io_handle_tw_list+0x55f/0x5c0 io_uring/io_uring.c:1057
tctx_task_work_run+0x109/0x3e0 io_uring/io_uring.c:1121
tctx_task_work+0x6d/0xc0 io_uring/io_uring.c:1139
task_work_run+0x268/0x310 kernel/task_work.c:239
io_run_task_work+0x43a/0x4a0 io_uring/io_uring.h:343
io_cqring_wait io_uring/io_uring.c:2527 [inline]
__do_sys_io_uring_enter io_uring/io_uring.c:3439 [inline]
__se_sys_io_uring_enter+0x204f/0x4ce0 io_uring/io_uring.c:3330
__x64_sys_io_uring_enter+0x11f/0x1a0 io_uring/io_uring.c:3330
x64_sys_call+0xce5/0x3c30 arch/x86/include/generated/asm/syscalls_64.h:427
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
and it is correct, as it's never initialized upfront. Hence the first
submission can end up using it uninitialized, if the recv wasn't
successful and the networking stack didn't honor ->msg_get_inq being set
and filling in the output value of ->msg_inq as requested.
Set it to 0 upfront when it's allocated, just to silence this KMSAN
warning. There's no side effect of using it uninitialized, it'll just
potentially cause the next receive to use a recv value hint that's not
accurate.
Fixes: c6f32c7d9e09 ("io_uring/net: get rid of ->prep_async() for receive side")
Reported-by: syzbot+068ff190354d2f74892f@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit c132be2c4fcc ("function_graph: Have the instances use their own
ftrace_ops for filtering"), function profiler (enabled via
function_profile_enabled) has been showing statistics for all functions,
ignoring set_ftrace_filter settings.
While tracers are instantiated, the function profiler is not. Therefore, it
should use the global set_ftrace_filter for consistency. This patch
modifies the function profiler to use the global filter, fixing the
filtering functionality.
Before (filtering not working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
schedule 314 22290594 us 70989.15 us
40372231 us
x64_sys_call 1527 8762510 us 5738.382 us
3414354 us
schedule_hrtimeout_range 176 8665356 us 49234.98 us
405618876 us
__x64_sys_ppoll 324 5656635 us 17458.75 us
19203976 us
do_sys_poll 324 5653747 us 17449.83 us
19214945 us
schedule_timeout 67 5531396 us 82558.15 us
2136740827 us
__x64_sys_pselect6 12 3029540 us 252461.7 us
63296940171 us
do_pselect.constprop.0 12 3029532 us 252461.0 us
63296952931 us
```
After (filtering working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
vfs_write 462 68476.43 us 148.217 us
25874.48 us
vfs_read 641 9611.356 us 14.994 us
28868.07 us
vfs_fstat 890 878.094 us 0.986 us
1.667 us
vfs_fstatat 227 757.176 us 3.335 us
18.928 us
vfs_statx 226 610.610 us 2.701 us
17.749 us
vfs_getattr_nosec 1187 460.919 us 0.388 us
0.326 us
vfs_statx_path 297 343.287 us 1.155 us
11.116 us
vfs_rename 6 291.575 us 48.595 us
9889.236 us
```
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250101190820.72534-1-enjuk@amazon.com
Fixes: c132be2c4fcc ("function_graph: Have the instances use their own ftrace_ops for filtering")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
In __ftrace_return_to_handler(), a loop iterates over the fgraph_array[]
elements, which are fgraph_ops. The loop checks if an element is a
fgraph_stub to prevent using a fgraph_stub afterward.
However, if the compiler reloads fgraph_array[] after this check, it might
race with an update to fgraph_array[] that introduces a fgraph_stub. This
could result in the stub being processed, but the stub contains a null
"func_hash" field, leading to a NULL pointer dereference.
To ensure that the gops compared against the fgraph_stub matches the gops
processed later, add a READ_ONCE(). A similar patch appears in commit
63a8dfb ("function_graph: Add READ_ONCE() when accessing fgraph_array[]").
Cc: stable@vger.kernel.org
Fixes: 37238abe3cb47 ("ftrace/function_graph: Pass fgraph_ops to function graph callbacks")
Link: https://lore.kernel.org/20241231113731.277668-1-zilin@seu.edu.cn
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
I haven't been an active participant for a couple of years now, and
after discussions at Linux Plumbers in 2024, Arnd is getting fresh help
from a few more participants.
It's time to remove myself, and spare myself from patches and pull
requests in my inbox.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Miquel Raynal
Marcus Folkesson
Nathan Chancellor
Bastien Curutchet
Md Sadre Alam
Linus Torvalds
Thomas Weißschuh
Jens Axboe
Mark Zhang
Meghana Malladi
MD Danish Anwar
Paolo Abeni
Eric Dumazet
Maciej S. Szmigiero
Willem de Bruijn
Liang Jie
Kohei Enju
Zilin Guan
Olof Johansson