| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
i.MX7ULP has a Cortex-A7 CPU which can run in RUN mode
or HSRUN mode, it is controlled in SMC1 module. The RUN
mode and HSRUN mode will use different clock source for
ARM, "divcore" for RUN mode and "hsrun_divcore" for HSRUN
mode, so the control bits in SMC1 module can be abstracted
as a HW clock mux, this patch adds HSRUN mode related
clocks in SCG1 module and adds "arm" clock in SMC1 module
to support RUN mode and HSRUN mode switch.
Latest clock tree in RUN mode as below:
firc 0 0 0 48000000 0 0 50000
firc_bus_clk 0 0 0 48000000 0 0 50000
hsrun_scs_sel 0 0 0 48000000 0 0 50000
hsrun_divcore 0 0 0 48000000 0 0 50000
sosc 3 3 3 24000000 0 0 50000
spll_pre_sel 1 1 1 24000000 0 0 50000
spll_pre_div 1 1 2 24000000 0 0 50000
spll 1 1 2 528000000 0 0 50000
spll_pfd0 1 1 1 500210526 0 0 50000
spll_pfd_sel 1 1 0 500210526 0 0 50000
spll_sel 1 1 0 500210526 0 0 50000
scs_sel 1 1 0 500210526 0 0 50000
divcore 1 1 0 500210526 0 0 50000
arm 1 1 0 500210526 0 0 50000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There are HSRUN mode clock mux and divider in SCG1 module,
and SMC1 can control i.MX7ULP CPU to run in RUN mode or
HSRUN mode, the mode switch bits are actually a clock mux,
add these clocks for clock driver and dtb to use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> (clk-mstp)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (ux500)
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add simple suspend/resume handlers to the driver to restore the chip
configuration after resume. It is possible that the chip was configured
with non-default values before suspend-resume cycle and that the chip
is powered down during this cycle, so the configuration could get lost.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
gcc_lpass_trig_clk is not used downstream, therefore there is no reason to
expect it to be needed for clients. Let's remove it because messing with
the clock has been observed to cause Linux hangs when the qdss_clk is
initialized by rpmcc.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 4807c71cc688 (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Similar to other qcom targets, gcc_mmss_noc_cfg_ahb_clk should not be
disabled. Any mmss access depends on this clock, and its been observed
that enabling mmssnoc_axi_rpm_clk with rpmcc results in an implicit
access to mmss and will crash the system if gcc_mmss_noc_cfg_ahb_clk is
disabled.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Fixes: 4807c71cc688 (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The current behavior is that clk_round_rate would return the same clock
rate passed to it for valid PLL configurations. This change will return
the exact rate the PLL will provide in accordance with clk API.
Signed-off-by: Robert Yang <decatf@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Rather than using the tegra_powergate_is_powered() function for
determining if a CPU is powered, use the tegra_pmc_cpu_is_powered()
instead which was created to get the CPU power status. Internally
tegra_pmc_cpu_is_powered() calls tegra_powergate_is_powered() and so
is equivalent.
The Tegra30 clock driver is the only public user of
tegra_powergate_is_powered() and so by updating the Tegra30 clock
driver to use tegra_pmc_cpu_is_powered(), we can then make
tegra_powergate_is_powered() a non-public function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When CONFIG_SMP is disabled, the tegra clk driver now fails to build:
drivers/clk/tegra/clk-tegra30.c: In function ‘tegra30_cpu_rail_off_ready’:
drivers/clk/tegra/clk-tegra30.c:1151:2: error: implicit declaration of function ‘tegra_pmc_cpu_is_powered’ [-Werror=implicit-function-declaration]
cpu_pwr_status = tegra_pmc_cpu_is_powered(1) ||
^
Fix the above error by removing the CONFIG_SMP ifdef around the
declaration around the PMC CPU APIs because although these are not
needed for non-SMP configurations, there is no harm in including these
for non-SMP builds either.
Fixes: 61866523ed6e ("clk: tegra30: Use Tegra CPU powergate helper function")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Get rid of 3 duplicate defines.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add imx8qxp lpcg driver support
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
And they're bedind the SCU clock.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add imx8qxp clk driver which is based on SCU firmware clock service.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Move the makefile rule higher in the file]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Remove the dependency between the i.MX8MQ CCM clock driver
and the CONFIG_SOC_IMX8MQ and use CONFIG_CLK_IMX8MQ instead.
CONFIG_CLK_IMX8MQ depends on ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add SCU clock common part which will be used by client clock drivers.
SCU clocks are totally different from the legacy clocks (No much
legacy things can be reused), it's using a firmware interface now based
on SCU protocol. So a new configuration option CONFIG_MXC_CLK_SCU is added.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Mark ccm_ipc_handle static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
Note:
This level of clock gating is provided after the clocks are generated
by the SCU resources and clock controls. Thus even if the clock is
enabled by these control bits, it might still not be running based
on the base resource.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
Anson Huang
Rob Herring
Marek Vasut
Jeffrey Hugo
Robert Yang
Jon Hunter
Marcel Ziswiler
Aisheng Dong
Abel Vesa