wireguard-linux/drivers/iio/accel/Makefile, branch jd/unified-crypt-queue

iio: accel: Add driver for the BMA400

2019-12-29T15:20:02Z

Add a IIO driver for the Bosch BMA400 3-axes ultra-low power accelerometer. The driver supports reading from the acceleration and temperature registers. The driver also supports reading and configuring the output data rate, oversampling ratio, and scale. Signed-off-by: Dan Robertson Reviewed-by: Andy Shevchenko Reviewed-by: Linus Walleij Signed-off-by: Jonathan Cameron

iio: adxl372: Add support for I2C communication

2018-09-08T14:54:38Z

The adxl372 is designed to communicate in either SPI or I2C protocol. It autodetects the format being used, requiring no configuration control to select the format. Signed-off-by: Stefan Popa Signed-off-by: Jonathan Cameron

iio: adxl372: Refactor the driver

2018-09-08T14:28:27Z

This patch restructures the existing adxl372 driver by adding a module for SPI and a header file, while the baseline module deals with the chip-logic. This is a necessary step, as this driver should support in the future a similar device which differs only in the type of interface used (I2C instead of SPI). Signed-off-by: Stefan Popa Signed-off-by: Jonathan Cameron

iio: adxl372: New driver for Analog Devices ADXL372 Accelerometer

2018-08-19T17:02:22Z

This patch adds basic support for Analog Devices ADXL372 SPI-Bus Three-Axis Digital Accelerometer. The device is probed and configured the with some initial default values. With this basic driver, it is possible to read raw acceleration data. Datasheet: http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL372.pdf Signed-off-by: Stefan Popa Signed-off-by: Jonathan Cameron

Staging: iio: adis16209: Move adis16209 driver out of staging

2018-03-30T12:50:36Z

Move the adis16209 driver out of staging directory and merge to the mainline IIO subsystem. Signed-off-by: Shreeya Patel Signed-off-by: Jonathan Cameron

Staging: iio: accel: adis16201: Move adis16201 driver out of staging

2018-03-24T14:26:19Z

Move adis16201 driver out of staging and merge into mainline IIO subsystem. Signed-off-by: Himanshu Jha Signed-off-by: Jonathan Cameron

Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

2017-11-14T04:53:28Z

Pull staging and IIO updates from Greg KH: "Here is the "big" staging and IIO driver update for 4.15-rc1. Lots and lots of little changes, almost all minor code cleanups as the Outreachy application process happened during this development cycle. Also happened was a lot of IIO driver activity, and the typec USB code moving out of staging to drivers/usb (same commits are in the USB tree on a persistent branch to not cause merge issues.) Overall, it's a wash, I think we added a few hundred more lines than removed, but really only a few thousand were modified at all. All of these have been in linux-next for a while. There might be a merge issue with Al's vfs tree in the pi433 driver (take his changes, they are always better), and the media tree with some of the odd atomisp cleanups (take the media tree's version)" * tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits) staging: lustre: add SPDX identifiers to all lustre files staging: greybus: Remove redundant license text staging: greybus: add SPDX identifiers to all greybus driver files staging: ccree: simplify ioread/iowrite staging: ccree: simplify registers access staging: ccree: simplify error handling logic staging: ccree: remove dead code staging: ccree: handle limiting of DMA masks staging: ccree: copy IV to DMAable memory staging: fbtft: remove redundant initialization of buf staging: sm750fb: Fix parameter mistake in poke32 staging: wilc1000: Fix bssid buffer offset in Txq staging: fbtft: fb_ssd1331: fix mirrored display staging: android: Fix checkpatch.pl error staging: greybus: loopback: convert loopback to use generic async operations staging: greybus: operation: add private data with get/set accessors staging: greybus: loopback: Fix iteration count on async path staging: greybus: loopback: Hold per-connection mutex across operations staging: greybus/loopback: use ktime_get() for time intervals staging: fsl-dpaa2/eth: Extra headroom in RX buffers ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

platform/chrome: Add cros_ec_accel_legacy driver

2017-10-14T19:34:01Z

Add driver to support older EC firmware that only support deprecated ec command. Rely on ACPI memory map register to access sensor information. Present same interface as the regular cros_ec sensor stack: - one iio device per accelerometer - use HTML5 axis definition - use iio abi units - accept calibration calls, but do nothing Chrome can use the same code than regular cros_ec sensor stack to calculate orientation and lid angle. Signed-off-by: Gwendal Grignou Signed-off-by: Thierry Escande Signed-off-by: Jonathan Cameron

iio: accel: adxl345: Add SPI support

2017-03-04T16:49:28Z

Add SPI driver that initializes SPI regmap for the adxl345 core driver. The driver supports the same functionality as I2C namely the x, y, z and scale readings. Signed-off-by: Eva Rachel Retuya Reviewed-by: Andy Shevchenko Signed-off-by: Jonathan Cameron