wireguard-linux/drivers/net/can, branch jd/bump-compilers

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2024-09-15T16:13:19Z

Merge in late fixes to prepare for the 6.12 net-next PR. No conflicts or adjacent changes. Signed-off-by: Jakub Kicinski

can: m_can: m_can_close(): stop clocks after device has been shut down

2024-09-12T07:45:54Z

After calling m_can_stop() an interrupt may be pending or NAPI might still be executed. This means the driver might still touch registers of the IP core after the clocks have been disabled. This is not good practice and might lead to aborts depending on the SoC integration. To avoid these potential problems, make m_can_close() symmetric to m_can_open(), i.e. stop the clocks at the end, right before shutting down the transceiver. Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: m_can: enable NAPI before enabling interrupts

2024-09-12T07:45:35Z

If an interrupt (RX-complete or error flag) is set when bringing up the CAN device, e.g. due to CAN bus traffic before initializing the device, when m_can_start() is called and interrupts are enabled, m_can_isr() is called immediately, which disables all CAN interrupts and calls napi_schedule(). Because napi_enable() isn't called until later in m_can_open(), the call to napi_schedule() never schedules the m_can_poll() callback and the device is left with interrupts disabled and can't receive any CAN packets until rebooted. This can be verified by running "cansend" from another device before setting the bitrate and calling "ip link set up can0" on the test device. Adding debug lines to m_can_isr() shows it's called with flags (IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts() and napi_schedule(), and then m_can_poll() is never called. Move the call to napi_enable() above the call to m_can_start() to enable any initial interrupt flags to be handled by m_can_poll() so that interrupts are reenabled. Add a call to napi_disable() in the error handling section of m_can_open(), to handle the case where later functions return errors. Also, in m_can_close(), move the call to napi_disable() below the call to m_can_stop() to ensure all interrupts are handled when bringing down the device. This race condition is much less likely to occur. Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to any SoC with a Bosch M_CAN controller. Signed-off-by: Jake Hamby Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: kvaser_pciefd: Enable 64-bit DMA addressing

2024-09-12T07:40:09Z

Enabling 64-bit addressing for DMA buffers will prevent issues on some memory constrained platforms like e.g. Raspberry Pi 5, where the driver won't load because it cannot allocate enough continuous memory in the default 32-bit memory address range. Signed-off-by: Martin Jocic Link: https://patch.msgid.link/d7340f78e3db305bfeeb8229d2dd1c9077e10b92.1725875278.git.martin.jocic@kvaser.com Signed-off-by: Marc Kleine-Budde

can: esd_usb: Remove CAN_CTRLMODE_3_SAMPLES for CAN-USB/3-FD

2024-09-12T07:40:09Z

Remove the CAN_CTRLMODE_3_SAMPLES announcement for CAN-USB/3-FD devices because these devices don't support it. The hardware has a Microchip SAM E70 microcontroller that uses a Bosch MCAN IP core as CAN FD controller. But this MCAN core doesn't support triple sampling. Fixes: 80662d943075 ("can: esd_usb: Add support for esd CAN-USB/3") Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje Reviewed-by: Vincent Mailhol Link: https://patch.msgid.link/20240904222740.2985864-2-stefan.maetje@esd.eu Signed-off-by: Marc Kleine-Budde

can: rockchip_canfd: rkcanfd_handle_error_int_reg_ec(): fix decoding of error code register

2024-09-11T08:58:18Z

Probably due to a copy/paste error rkcanfd_handle_error_int_reg_ec() checks twice if the RKCANFD_REG_ERROR_CODE_TX_ACK_EOF bit is set in reg_ec. Keep the correct check for RKCANFD_REG_ERROR_CODE_TX_ACK_EOF and remove the superfluous one. Reported-by: Dan Carpenter Closes: https://patch.msgid.link/9a46d10d-e4e3-40a5-8fb6-f4637959f124@stanley.mountain Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller") Link: https://patch.msgid.link/20240911-can-rockchip_canfd-fixes-v1-2-5ce385b5ab10@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: rockchip_canfd: rkcanfd_timestamp_init(): rework delay calculation

2024-09-11T08:58:18Z

Rework the delay calculation to only require a single 64-bit division. Signed-off-by: Arnd Bergmann [mkl: port to on-top of existing 32-bit division fix] Link: https://patch.msgid.link/20240911-can-rockchip_canfd-fixes-v1-1-5ce385b5ab10@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: m_can: m_can_chip_config(): mask timestamp wraparound IRQ

2024-09-11T08:52:47Z

On the Microchip SAMA7G54 MPU the IR_TSW (timestamp wraparound) fires at about 1 Hz, but the driver doesn't care about it. Add it to the list of interrupts to disable in m_can_chip_config to reduce unneeded wakeups. Link: https://patch.msgid.link/DM8PR14MB5221D9DD3A7F2130EF161AF7EF9E2@DM8PR14MB5221.namprd14.prod.outlook.com Signed-off-by: Jake Hamby Link: https://patch.msgid.link/20240911-can-m_can-mask-timestamp-wraparound-irq-v1-1-0155b70dc827@pengutronix.de Signed-off-by: Marc Kleine-Budde

can: usb: Kconfig: Fix list of devices for esd_usb driver

2024-09-11T08:46:53Z

The CAN-USB/3-FD was missing on the list of supported devices. Signed-off-by: Stefan Mätje Link: https://patch.msgid.link/20240910170236.2287637-1-stefan.maetje@esd.eu Signed-off-by: Marc Kleine-Budde

can: Switch back to struct platform_driver::remove()

2024-09-11T07:37:16Z

After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all can drivers to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. Signed-off-by: Uwe Kleine-König Link: https://patch.msgid.link/20240909072742.381003-2-u.kleine-koenig@baylibre.com Signed-off-by: Marc Kleine-Budde