wireguard-linux/drivers/thunderbolt/usb4.c, branch jd/orphan-parallel

thunderbolt: Enable wakes from system suspend

2020-09-03T09:06:42Z

In order for the router and the whole domain to wake up from system suspend states we need to enable wakes for the connected routers. For device routers we enable wakes from PCIe and USB 3.x. This allows devices such as keyboards connected to USB 3.x hub that is tunneled to wake the system up as expected. For all routers we enabled wake on USB4 for each connected ports. This is used to propagate the wake from router to another. Do the same for legacy routers through link controller vendor specific registers as documented in USB4 spec chapter 13. While there correct kernel-doc of usb4_switch_set_sleep() -- it does not enable wakes instead there is a separate function (usb4_switch_set_wake()) that does. Signed-off-by: Mika Westerberg

thunderbolt: Configure port for XDomain

2020-09-03T09:06:41Z

When the port is connected to another host it should be marked as such in the USB4 port capability. This information is used by the router during sleep and wakeup. Also do the same for legacy switches via link controller vendor specific registers. Signed-off-by: Mika Westerberg

thunderbolt: Set port configured for both ends of the link

2020-09-03T09:06:41Z

Both ends of the link needs to have this set. Otherwise the link is not re-established properly after sleep. Now since it is possible to have mixed USB4 and Thunderbolt 1, 2 and 3 devices we need to split the link configuration functionality to happen per port so we can pick the correct implementation. Signed-off-by: Mika Westerberg

thunderbolt: Configure link after lane bonding is enabled

2020-09-03T09:06:41Z

During testing it was noticed that the link is not properly restored after the domain exits sleep if the link configured bits are set before lane bonding is enabled. The USB4 spec does not say in which order these need to be set but setting link configured afterwards makes the link restoration work so we do that instead. Signed-off-by: Mika Westerberg

thunderbolt: Ensure left shift of 512 does not overflow a 32 bit int

2020-07-01T10:46:47Z

The 32 bit int value 512 is being left shifted and then used in a context that expects the expression to be a larger unsigned long. There may be a potential integer overflow, so make 512 a UL before shift to avoid any such issues. Addresses-Coverity: ("Uninintentional integer overflow") Fixes: 3b1d8d577ca8 ("thunderbolt: Implement USB3 bandwidth negotiation routines") Signed-off-by: Colin Ian King Signed-off-by: Mika Westerberg

thunderbolt: Implement USB4 port sideband operations for retimer access

2020-06-22T16:58:32Z

USB4 spec specifies standard set of sideband operations that are send over the low speed link to access either retimers on the link or the link parter (the other router). The USB4 retimer spec extends these and adds operations for retimer NVM upgrade. This implements the retimer access and NVM upgrade USB4 port sideband operations which we need for retimer support in the patch that follows. Signed-off-by: Rajmohan Mani Co-developed-by: Mika Westerberg Signed-off-by: Mika Westerberg

thunderbolt: Retry USB4 block read operation

2020-06-22T16:58:32Z

Especially when accessing retimers over USB4 sideband operations the possibility to get read errors seems to be higher so make the usb4_do_read_data() retry a couple of times if it sees any other error than -ENODEV (device is gone). We can only do this for read side because it carries the offset as part of metadata (as opposed to writes). Signed-off-by: Mika Westerberg

thunderbolt: Generalize usb4_switch_do_[read|write]_data()

2020-06-22T16:58:32Z

Currently these functions operate on struct tb_switch but we are going to need the same functionality with retimers as well so make the two functions work with an arbitrary object that gets passed as parameter to the callbacks. Signed-off-by: Mika Westerberg

thunderbolt: Implement USB3 bandwidth negotiation routines

2020-06-22T16:58:20Z

Each host router USB3 downstream adapter has a set of registers that are used to negotiate bandwidth between the connection manager and the internal xHCI controller. These registers allow dynamic bandwidth management for USB3 isochronous traffic based on what is actually consumed vs. allocated at any given time. Implement these USB3 bandwidth negotiation routines to allow the software connection manager take advantage of these. Signed-off-by: Mika Westerberg

thunderbolt: Make usb4_switch_map_pcie_down() also return enabled ports

2020-06-22T16:58:20Z

Just for symmetry with the usb4_switch_map_usb3_down() make this one also return ports that are enabled. Signed-off-by: Mika Westerberg