Merge branch 'net-phy-bcm5481x-add-support-for-broadr-reach-mode'

Kamil Horák says:

====================
net: phy: bcm5481x: add support for BroadR-Reach mode

PATCH 1 - Add the 10baseT1BRR_Full link mode

PATCH 2 - Add the definitions of LRE registers, necessary to use
   BroadR-Reach modes on the BCM5481x PHY

PATCH 3 - Add brr-mode flag to switch between IEEE802.3 and BroadR-Reach

PATCH 4 - Implementation of the BroadR-Reach modes for the Broadcom
   PHYs
====================

Link: https://patch.msgid.link/20240712150709.3134474-1-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

8 files changed, 596 insertions, 29 deletions

diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
index 8fb2a6ee7e5b..d9b62741a225 100644
--- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -93,6 +93,14 @@ properties:
       the turn around line low at end of the control phase of the
       MDIO transaction.
 
+  brr-mode:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If set, indicates the network cable interface is an alternative one as
+      defined in the BroadR-Reach link mode specification under 1BR-100 and
+      1BR-10 names. The PHY must be configured to operate in BroadR-Reach mode
+      by software.
+
   clocks:
     maxItems: 1
     description:
diff --git a/drivers/net/phy/bcm-phy-lib.c b/drivers/net/phy/bcm-phy-lib.c
index 876f28fd8256..6c52f7dda514 100644
--- a/drivers/net/phy/bcm-phy-lib.c
+++ b/drivers/net/phy/bcm-phy-lib.c
@@ -794,6 +794,49 @@ out:
 	return ret;
 }
 
+static int bcm_setup_lre_forced(struct phy_device *phydev)
+{
+	u16 ctl = 0;
+
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	if (phydev->speed == SPEED_100)
+		ctl |= LRECR_SPEED100;
+
+	if (phydev->duplex != DUPLEX_FULL)
+		return -EOPNOTSUPP;
+
+	return phy_modify(phydev, MII_BCM54XX_LRECR, LRECR_SPEED100, ctl);
+}
+
+/**
+ * bcm_linkmode_adv_to_lre_adv_t - translate linkmode advertisement to LDS
+ * @advertising: the linkmode advertisement settings
+ * Return: LDS Auto-Negotiation Advertised Ability register value
+ *
+ * A small helper function that translates linkmode advertisement
+ * settings to phy LDS autonegotiation advertisements for the
+ * MII_BCM54XX_LREANAA register of Broadcom PHYs capable of LDS
+ */
+static u32 bcm_linkmode_adv_to_lre_adv_t(unsigned long *advertising)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT,
+			      advertising))
+		result |= LREANAA_10_1PAIR;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT1_Full_BIT,
+			      advertising))
+		result |= LREANAA_100_1PAIR;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertising))
+		result |= LRELPA_PAUSE;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertising))
+		result |= LRELPA_PAUSE_ASYM;
+
+	return result;
+}
+
 int bcm_phy_cable_test_start(struct phy_device *phydev)
 {
 	return _bcm_phy_cable_test_start(phydev, false);
@@ -1066,6 +1109,78 @@ int bcm_phy_led_brightness_set(struct phy_device *phydev,
 }
 EXPORT_SYMBOL_GPL(bcm_phy_led_brightness_set);
 
+int bcm_setup_lre_master_slave(struct phy_device *phydev)
+{
+	u16 ctl = 0;
+
+	switch (phydev->master_slave_set) {
+	case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+	case MASTER_SLAVE_CFG_MASTER_FORCE:
+		ctl = LRECR_MASTER;
+		break;
+	case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+	case MASTER_SLAVE_CFG_SLAVE_FORCE:
+		break;
+	case MASTER_SLAVE_CFG_UNKNOWN:
+	case MASTER_SLAVE_CFG_UNSUPPORTED:
+		return 0;
+	default:
+		phydev_warn(phydev, "Unsupported Master/Slave mode\n");
+		return -EOPNOTSUPP;
+	}
+
+	return phy_modify_changed(phydev, MII_BCM54XX_LRECR, LRECR_MASTER, ctl);
+}
+EXPORT_SYMBOL_GPL(bcm_setup_lre_master_slave);
+
+int bcm_config_lre_aneg(struct phy_device *phydev, bool changed)
+{
+	int err;
+
+	if (genphy_config_eee_advert(phydev))
+		changed = true;
+
+	err = bcm_setup_lre_master_slave(phydev);
+	if (err < 0)
+		return err;
+	else if (err)
+		changed = true;
+
+	if (phydev->autoneg != AUTONEG_ENABLE)
+		return bcm_setup_lre_forced(phydev);
+
+	err = bcm_config_lre_advert(phydev);
+	if (err < 0)
+		return err;
+	else if (err)
+		changed = true;
+
+	return genphy_check_and_restart_aneg(phydev, changed);
+}
+EXPORT_SYMBOL_GPL(bcm_config_lre_aneg);
+
+/**
+ * bcm_config_lre_advert - sanitize and advertise Long-Distance Signaling
+ *  auto-negotiation parameters
+ * @phydev: target phy_device struct
+ * Return:  0 if the PHY's advertisement hasn't changed, < 0 on error,
+ *          > 0 if it has changed
+ *
+ * Writes MII_BCM54XX_LREANAA with the appropriate values. The values are to be
+ *   sanitized before, to make sure we only advertise what is supported.
+ *  The sanitization is done already in phy_ethtool_ksettings_set()
+ */
+int bcm_config_lre_advert(struct phy_device *phydev)
+{
+	u32 adv = bcm_linkmode_adv_to_lre_adv_t(phydev->advertising);
+
+	/* Setup BroadR-Reach mode advertisement */
+	return phy_modify_changed(phydev, MII_BCM54XX_LREANAA,
+				 LRE_ADVERTISE_ALL | LREANAA_PAUSE |
+				 LREANAA_PAUSE_ASYM, adv);
+}
+EXPORT_SYMBOL_GPL(bcm_config_lre_advert);
+
 MODULE_DESCRIPTION("Broadcom PHY Library");
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Broadcom Corporation");
diff --git a/drivers/net/phy/bcm-phy-lib.h b/drivers/net/phy/bcm-phy-lib.h
index b52189e45a84..bceddbc860eb 100644
--- a/drivers/net/phy/bcm-phy-lib.h
+++ b/drivers/net/phy/bcm-phy-lib.h
@@ -121,4 +121,8 @@ irqreturn_t bcm_phy_wol_isr(int irq, void *dev_id);
 int bcm_phy_led_brightness_set(struct phy_device *phydev,
 			       u8 index, enum led_brightness value);
 
+int bcm_setup_lre_master_slave(struct phy_device *phydev);
+int bcm_config_lre_aneg(struct phy_device *phydev, bool changed);
+int bcm_config_lre_advert(struct phy_device *phydev);
+
 #endif /* _LINUX_BCM_PHY_LIB_H */
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 370e4ed45098..ddded162c44c 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -5,6 +5,8 @@
  *	Broadcom BCM5411, BCM5421 and BCM5461 Gigabit Ethernet
  *	transceivers.
  *
+ *	Broadcom BCM54810, BCM54811 BroadR-Reach transceivers.
+ *
  *	Copyright (c) 2006  Maciej W. Rozycki
  *
  *	Inspired by code written by Amy Fong.
@@ -36,6 +38,29 @@ struct bcm54xx_phy_priv {
 	struct bcm_ptp_private *ptp;
 	int	wake_irq;
 	bool	wake_irq_enabled;
+	bool	brr_mode;
+};
+
+/* Link modes for BCM58411 PHY */
+static const int bcm54811_linkmodes[] = {
+	ETHTOOL_LINK_MODE_100baseT1_Full_BIT,
+	ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT,
+	ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+	ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
+	ETHTOOL_LINK_MODE_100baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_100baseT_Half_BIT,
+	ETHTOOL_LINK_MODE_10baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_10baseT_Half_BIT
+};
+
+/* Long-Distance Signaling (BroadR-Reach mode aneg) relevant linkmode bits */
+static const int lds_br_bits[] = {
+	ETHTOOL_LINK_MODE_Autoneg_BIT,
+	ETHTOOL_LINK_MODE_Pause_BIT,
+	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+	ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT,
+	ETHTOOL_LINK_MODE_100baseT1_Full_BIT
 };
 
 static bool bcm54xx_phy_can_wakeup(struct phy_device *phydev)
@@ -347,6 +372,61 @@ static void bcm54xx_ptp_config_init(struct phy_device *phydev)
 		bcm_ptp_config_init(phydev);
 }
 
+static int bcm5481x_set_brrmode(struct phy_device *phydev, bool on)
+{
+	int reg;
+	int err;
+	u16 val;
+
+	reg = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
+
+	if (reg < 0)
+		return reg;
+
+	if (on)
+		reg |= BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+	else
+		reg &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+
+	err = bcm_phy_write_exp(phydev,
+				BCM54810_EXP_BROADREACH_LRE_MISC_CTL, reg);
+	if (err)
+		return err;
+
+	/* Ensure LRE or IEEE register set is accessed according to the brr
+	 *  on/off, thus set the override
+	 */
+	val = BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL_EN;
+	if (!on)
+		val |= BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL_OVERRIDE_VAL;
+
+	return bcm_phy_write_exp(phydev,
+				 BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL, val);
+}
+
+static int bcm54811_config_init(struct phy_device *phydev)
+{
+	struct bcm54xx_phy_priv *priv = phydev->priv;
+	int err, reg;
+
+	/* Enable CLK125 MUX on LED4 if ref clock is enabled. */
+	if (!(phydev->dev_flags & PHY_BRCM_RX_REFCLK_UNUSED)) {
+		reg = bcm_phy_read_exp(phydev, BCM54612E_EXP_SPARE0);
+		if (reg < 0)
+			return reg;
+		err = bcm_phy_write_exp(phydev, BCM54612E_EXP_SPARE0,
+					BCM54612E_LED4_CLK125OUT_EN | reg);
+		if (err < 0)
+			return err;
+	}
+
+	/* With BCM54811, BroadR-Reach implies no autoneg */
+	if (priv->brr_mode)
+		phydev->autoneg = 0;
+
+	return bcm5481x_set_brrmode(phydev, priv->brr_mode);
+}
+
 static int bcm54xx_config_init(struct phy_device *phydev)
 {
 	int reg, err, val;
@@ -399,6 +479,9 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 					BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
 					val);
 		break;
+	case PHY_ID_BCM54811:
+		err = bcm54811_config_init(phydev);
+		break;
 	}
 	if (err)
 		return err;
@@ -553,52 +636,117 @@ static int bcm54810_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return -EOPNOTSUPP;
 }
 
-static int bcm54811_config_init(struct phy_device *phydev)
+
+/**
+ * bcm5481x_read_abilities - read PHY abilities from LRESR or Clause 22
+ * (BMSR) registers, based on whether the PHY is in BroadR-Reach or IEEE mode
+ * @phydev: target phy_device struct
+ *
+ * Description: Reads the PHY's abilities and populates phydev->supported
+ * accordingly. The register to read the abilities from is determined by
+ * the brr mode setting of the PHY as read from the device tree.
+ * Note that the LRE and IEEE sets of abilities are disjunct, in other words,
+ * not only the link modes differ, but also the auto-negotiation and
+ * master-slave setup is controlled differently.
+ *
+ * Returns: 0 on success, < 0 on failure
+ */
+static int bcm5481x_read_abilities(struct phy_device *phydev)
 {
-	int err, reg;
+	struct device_node *np = phydev->mdio.dev.of_node;
+	struct bcm54xx_phy_priv *priv = phydev->priv;
+	int i, val, err;
 
-	/* Disable BroadR-Reach function. */
-	reg = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
-	reg &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
-	err = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
-				reg);
-	if (err < 0)
+	for (i = 0; i < ARRAY_SIZE(bcm54811_linkmodes); i++)
+		linkmode_clear_bit(bcm54811_linkmodes[i], phydev->supported);
+
+	priv->brr_mode = of_property_read_bool(np, "brr-mode");
+
+	/* Set BroadR-Reach mode as configured in the DT. */
+	err = bcm5481x_set_brrmode(phydev, priv->brr_mode);
+	if (err)
 		return err;
 
-	err = bcm54xx_config_init(phydev);
+	if (priv->brr_mode) {
+		linkmode_set_bit_array(phy_basic_ports_array,
+				       ARRAY_SIZE(phy_basic_ports_array),
+				       phydev->supported);
 
-	/* Enable CLK125 MUX on LED4 if ref clock is enabled. */
-	if (!(phydev->dev_flags & PHY_BRCM_RX_REFCLK_UNUSED)) {
-		reg = bcm_phy_read_exp(phydev, BCM54612E_EXP_SPARE0);
-		err = bcm_phy_write_exp(phydev, BCM54612E_EXP_SPARE0,
-					BCM54612E_LED4_CLK125OUT_EN | reg);
-		if (err < 0)
-			return err;
+		val = phy_read(phydev, MII_BCM54XX_LRESR);
+		if (val < 0)
+			return val;
+
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+				 phydev->supported,
+				 val & LRESR_LDSABILITY);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT1_Full_BIT,
+				 phydev->supported,
+				 val & LRESR_100_1PAIR);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT,
+				 phydev->supported,
+				 val & LRESR_10_1PAIR);
+		return 0;
 	}
 
-	return err;
+	return genphy_read_abilities(phydev);
 }
 
-static int bcm5481_config_aneg(struct phy_device *phydev)
+static int bcm5481x_config_delay_swap(struct phy_device *phydev)
 {
 	struct device_node *np = phydev->mdio.dev.of_node;
-	int ret;
-
-	/* Aneg firstly. */
-	ret = genphy_config_aneg(phydev);
 
-	/* Then we can set up the delay. */
+	/* Set up the delay. */
 	bcm54xx_config_clock_delay(phydev);
 
 	if (of_property_read_bool(np, "enet-phy-lane-swap")) {
 		/* Lane Swap - Undocumented register...magic! */
-		ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
-					0x11B);
+		int ret = bcm_phy_write_exp(phydev,
+					    MII_BCM54XX_EXP_SEL_ER + 0x9,
+					    0x11B);
 		if (ret < 0)
 			return ret;
 	}
 
-	return ret;
+	return 0;
+}
+
+static int bcm5481_config_aneg(struct phy_device *phydev)
+{
+	struct bcm54xx_phy_priv *priv = phydev->priv;
+	int ret;
+
+	/* Aneg firstly. */
+	if (priv->brr_mode)
+		ret = bcm_config_lre_aneg(phydev, false);
+	else
+		ret = genphy_config_aneg(phydev);
+
+	if (ret)
+		return ret;
+
+	/* Then we can set up the delay and swap. */
+	return bcm5481x_config_delay_swap(phydev);
+}
+
+static int bcm54811_config_aneg(struct phy_device *phydev)
+{
+	struct bcm54xx_phy_priv *priv = phydev->priv;
+	int ret;
+
+	/* Aneg firstly. */
+	if (priv->brr_mode) {
+		/* BCM54811 is only capable of autonegotiation in IEEE mode */
+		phydev->autoneg = 0;
+		ret = bcm_config_lre_aneg(phydev, false);
+	} else {
+		ret = genphy_config_aneg(phydev);
+	}
+
+	if (ret)
+		return ret;
+
+	/* Then we can set up the delay and swap. */
+	return bcm5481x_config_delay_swap(phydev);
 }
 
 struct bcm54616s_phy_priv {
@@ -1062,6 +1210,203 @@ static void bcm54xx_link_change_notify(struct phy_device *phydev)
 	bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP08, ret);
 }
 
+static int lre_read_master_slave(struct phy_device *phydev)
+{
+	int cfg = MASTER_SLAVE_CFG_UNKNOWN, state;
+	int val;
+
+	/* In BroadR-Reach mode we are always capable of master-slave
+	 *  and there is no preferred master or slave configuration
+	 */
+	phydev->master_slave_get = MASTER_SLAVE_CFG_UNKNOWN;
+	phydev->master_slave_state = MASTER_SLAVE_STATE_UNKNOWN;
+
+	val = phy_read(phydev, MII_BCM54XX_LRECR);
+	if (val < 0)
+		return val;
+
+	if ((val & LRECR_LDSEN) == 0) {
+		if (val & LRECR_MASTER)
+			cfg = MASTER_SLAVE_CFG_MASTER_FORCE;
+		else
+			cfg = MASTER_SLAVE_CFG_SLAVE_FORCE;
+	}
+
+	val = phy_read(phydev, MII_BCM54XX_LRELDSE);
+	if (val < 0)
+		return val;
+
+	if (val & LDSE_MASTER)
+		state = MASTER_SLAVE_STATE_MASTER;
+	else
+		state = MASTER_SLAVE_STATE_SLAVE;
+
+	phydev->master_slave_get = cfg;
+	phydev->master_slave_state = state;
+
+	return 0;
+}
+
+/* Read LDS Link Partner Ability in BroadR-Reach mode */
+static int lre_read_lpa(struct phy_device *phydev)
+{
+	int i, lrelpa;
+
+	if (phydev->autoneg != AUTONEG_ENABLE) {
+		if (!phydev->autoneg_complete) {
+			/* aneg not yet done, reset all relevant bits */
+			for (i = 0; i < ARRAY_SIZE(lds_br_bits); i++)
+				linkmode_clear_bit(lds_br_bits[i],
+						   phydev->lp_advertising);
+
+			return 0;
+		}
+
+		/* Long-Distance Signaling Link Partner Ability */
+		lrelpa = phy_read(phydev, MII_BCM54XX_LRELPA);
+		if (lrelpa < 0)
+			return lrelpa;
+
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+				 phydev->lp_advertising,
+				 lrelpa & LRELPA_PAUSE_ASYM);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+				 phydev->lp_advertising,
+				 lrelpa & LRELPA_PAUSE);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT1_Full_BIT,
+				 phydev->lp_advertising,
+				 lrelpa & LRELPA_100_1PAIR);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT,
+				 phydev->lp_advertising,
+				 lrelpa & LRELPA_10_1PAIR);
+	} else {
+		linkmode_zero(phydev->lp_advertising);
+	}
+
+	return 0;
+}
+
+static int lre_read_status_fixed(struct phy_device *phydev)
+{
+	int lrecr = phy_read(phydev, MII_BCM54XX_LRECR);
+
+	if (lrecr < 0)
+		return lrecr;
+
+	phydev->duplex = DUPLEX_FULL;
+
+	if (lrecr & LRECR_SPEED100)
+		phydev->speed = SPEED_100;
+	else
+		phydev->speed = SPEED_10;
+
+	return 0;
+}
+
+/**
+ * lre_update_link - update link status in @phydev
+ * @phydev: target phy_device struct
+ * Return:  0 on success, < 0 on error
+ *
+ * Description: Update the value in phydev->link to reflect the
+ *   current link value.  In order to do this, we need to read
+ *   the status register twice, keeping the second value.
+ *   This is a genphy_update_link modified to work on LRE registers
+ *   of BroadR-Reach PHY
+ */
+static int lre_update_link(struct phy_device *phydev)
+{
+	int status = 0, lrecr;
+
+	lrecr = phy_read(phydev, MII_BCM54XX_LRECR);
+	if (lrecr < 0)
+		return lrecr;
+
+	/* Autoneg is being started, therefore disregard BMSR value and
+	 * report link as down.
+	 */
+	if (lrecr & BMCR_ANRESTART)
+		goto done;
+
+	/* The link state is latched low so that momentary link
+	 * drops can be detected. Do not double-read the status
+	 * in polling mode to detect such short link drops except
+	 * the link was already down.
+	 */
+	if (!phy_polling_mode(phydev) || !phydev->link) {
+		status = phy_read(phydev, MII_BCM54XX_LRESR);
+		if (status < 0)
+			return status;
+		else if (status & LRESR_LSTATUS)
+			goto done;
+	}
+
+	/* Read link and autonegotiation status */
+	status = phy_read(phydev, MII_BCM54XX_LRESR);
+	if (status < 0)
+		return status;
+done:
+	phydev->link = status & LRESR_LSTATUS ? 1 : 0;
+	phydev->autoneg_complete = status & LRESR_LDSCOMPLETE ? 1 : 0;
+
+	/* Consider the case that autoneg was started and "aneg complete"
+	 * bit has been reset, but "link up" bit not yet.
+	 */
+	if (phydev->autoneg == AUTONEG_ENABLE && !phydev->autoneg_complete)
+		phydev->link = 0;
+
+	return 0;
+}
+
+/* Get the status in BroadRReach mode just like genphy_read_status does
+*   in normal mode
+*/
+static int bcm54811_lre_read_status(struct phy_device *phydev)
+{
+	int err, old_link = phydev->link;
+
+	/* Update the link, but return if there was an error */
+	err = lre_update_link(phydev);
+	if (err)
+		return err;
+
+	/* why bother the PHY if nothing can have changed */
+	if (phydev->autoneg ==
+		AUTONEG_ENABLE && old_link && phydev->link)
+		return 0;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	err = lre_read_master_slave(phydev);
+	if (err < 0)
+		return err;
+
+	/* Read LDS Link Partner Ability */
+	err = lre_read_lpa(phydev);
+	if (err < 0)
+		return err;
+
+	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
+		phy_resolve_aneg_linkmode(phydev);
+	else if (phydev->autoneg == AUTONEG_DISABLE)
+		err = lre_read_status_fixed(phydev);
+
+	return err;
+}
+
+static int bcm54811_read_status(struct phy_device *phydev)
+{
+	struct bcm54xx_phy_priv *priv = phydev->priv;
+
+	if (priv->brr_mode)
+		return  bcm54811_lre_read_status(phydev);
+
+	return genphy_read_status(phydev);
+}
+
 static struct phy_driver broadcom_drivers[] = {
 {
 	.phy_id		= PHY_ID_BCM5411,
@@ -1211,10 +1556,12 @@ static struct phy_driver broadcom_drivers[] = {
 	.get_strings	= bcm_phy_get_strings,
 	.get_stats	= bcm54xx_get_stats,
 	.probe		= bcm54xx_phy_probe,
-	.config_init    = bcm54811_config_init,
-	.config_aneg    = bcm5481_config_aneg,
+	.config_init    = bcm54xx_config_init,
+	.config_aneg    = bcm54811_config_aneg,
 	.config_intr    = bcm_phy_config_intr,
 	.handle_interrupt = bcm_phy_handle_interrupt,
+	.read_status	= bcm54811_read_status,
+	.get_features	= bcm5481x_read_abilities,
 	.suspend	= bcm54xx_suspend,
 	.resume		= bcm54xx_resume,
 	.link_change_notify	= bcm54xx_link_change_notify,
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index a235ea2264a7..1f98b6a96c15 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -13,7 +13,7 @@
  */
 const char *phy_speed_to_str(int speed)
 {
-	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 102,
+	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 103,
 		"Enum ethtool_link_mode_bit_indices and phylib are out of sync. "
 		"If a speed or mode has been added please update phy_speed_to_str "
 		"and the PHY settings array.\n");
@@ -266,6 +266,7 @@ static const struct phy_setting settings[] = {
 	PHY_SETTING(     10, FULL,     10baseT1S_Full		),
 	PHY_SETTING(     10, HALF,     10baseT1S_Half		),
 	PHY_SETTING(     10, HALF,     10baseT1S_P2MP_Half	),
+	PHY_SETTING(     10, FULL,     10baseT1BRR_Full		),
 };
 #undef PHY_SETTING
 
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 1394ba302367..028b3e00378e 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -271,12 +271,100 @@
 #define BCM5482_SSD_SGMII_SLAVE_EN	0x0002	/* Slave mode enable */
 #define BCM5482_SSD_SGMII_SLAVE_AD	0x0001	/* Slave auto-detection */
 
+/* BroadR-Reach LRE Registers. */
+#define MII_BCM54XX_LRECR		0x00	/* LRE Control Register                    */
+#define MII_BCM54XX_LRESR		0x01	/* LRE Status Register                     */
+#define MII_BCM54XX_LREPHYSID1		0x02	/* LRE PHYS ID 1                           */
+#define MII_BCM54XX_LREPHYSID2		0x03	/* LRE PHYS ID 2                           */
+#define MII_BCM54XX_LREANAA		0x04	/* LDS Auto-Negotiation Advertised Ability */
+#define MII_BCM54XX_LREANAC		0x05	/* LDS Auto-Negotiation Advertised Control */
+#define MII_BCM54XX_LREANPT		0x06	/* LDS Ability Next Page Transmit          */
+#define MII_BCM54XX_LRELPA		0x07	/* LDS Link Partner Ability                */
+#define MII_BCM54XX_LRELPNPM		0x08	/* LDS Link Partner Next Page Message      */
+#define MII_BCM54XX_LRELPNPC		0x09	/* LDS Link Partner Next Page Control      */
+#define MII_BCM54XX_LRELDSE		0x0a	/* LDS Expansion Register                  */
+#define MII_BCM54XX_LREES		0x0f	/* LRE Extended Status                     */
+
+/* LRE control register. */
+#define LRECR_RESET			0x8000	/* Reset to default state      */
+#define LRECR_LOOPBACK			0x4000	/* Internal Loopback           */
+#define LRECR_LDSRES			0x2000	/* Restart LDS Process         */
+#define LRECR_LDSEN			0x1000	/* LDS Enable                  */
+#define LRECR_PDOWN			0x0800	/* Enable low power state      */
+#define LRECR_ISOLATE			0x0400	/* Isolate data paths from MII */
+#define LRECR_SPEED100			0x0200	/* Select 100 Mbps             */
+#define LRECR_SPEED10			0x0000	/* Select 10 Mbps              */
+#define LRECR_4PAIRS			0x0020	/* Select 4 Pairs              */
+#define LRECR_2PAIRS			0x0010	/* Select 2 Pairs              */
+#define LRECR_1PAIR			0x0000	/* Select 1 Pair               */
+#define LRECR_MASTER			0x0008	/* Force Master when LDS disabled */
+#define LRECR_SLAVE			0x0000	/* Force Slave when LDS disabled  */
+
+/* LRE status register. */
+#define LRESR_100_1PAIR			0x2000	/* Can do 100Mbps 1 Pair       */
+#define LRESR_100_4PAIR			0x1000	/* Can do 100Mbps 4 Pairs      */
+#define LRESR_100_2PAIR			0x0800	/* Can do 100Mbps 2 Pairs      */
+#define LRESR_10_2PAIR			0x0400	/* Can do 10Mbps 2 Pairs       */
+#define LRESR_10_1PAIR			0x0200	/* Can do 10Mbps 1 Pair        */
+#define LRESR_ESTATEN			0x0100	/* Extended Status in R15      */
+#define LRESR_RESV			0x0080	/* Unused...                   */
+#define LRESR_MFPS			0x0040	/* Can suppress Management Frames Preamble */
+#define LRESR_LDSCOMPLETE		0x0020	/* LDS Auto-negotiation complete */
+#define LRESR_8023			0x0010	/* Has IEEE 802.3 Support      */
+#define LRESR_LDSABILITY		0x0008	/* LDS auto-negotiation capable */
+#define LRESR_LSTATUS			0x0004	/* Link status                 */
+#define LRESR_JCD			0x0002	/* Jabber detected             */
+#define LRESR_ERCAP			0x0001	/* Ext-reg capability          */
+
+/* LDS Auto-Negotiation Advertised Ability. */
+#define LREANAA_PAUSE_ASYM		0x8000	/* Can pause asymmetrically    */
+#define LREANAA_PAUSE			0x4000	/* Can pause                   */
+#define LREANAA_100_1PAIR		0x0020	/* Can do 100Mbps 1 Pair       */
+#define LREANAA_100_4PAIR		0x0010	/* Can do 100Mbps 4 Pair       */
+#define LREANAA_100_2PAIR		0x0008	/* Can do 100Mbps 2 Pair       */
+#define LREANAA_10_2PAIR		0x0004	/* Can do 10Mbps 2 Pair        */
+#define LREANAA_10_1PAIR		0x0002	/* Can do 10Mbps 1 Pair        */
+
+#define LRE_ADVERTISE_FULL		(LREANAA_100_1PAIR | LREANAA_100_4PAIR | \
+					 LREANAA_100_2PAIR | LREANAA_10_2PAIR | \
+					 LREANAA_10_1PAIR)
+
+#define LRE_ADVERTISE_ALL		LRE_ADVERTISE_FULL
+
+/* LDS Link Partner Ability. */
+#define LRELPA_PAUSE_ASYM		0x8000	/* Supports asymmetric pause   */
+#define LRELPA_PAUSE			0x4000	/* Supports pause capability   */
+#define LRELPA_100_1PAIR		0x0020	/* 100Mbps 1 Pair capable      */
+#define LRELPA_100_4PAIR		0x0010	/* 100Mbps 4 Pair capable      */
+#define LRELPA_100_2PAIR		0x0008	/* 100Mbps 2 Pair capable      */
+#define LRELPA_10_2PAIR			0x0004	/* 10Mbps 2 Pair capable       */
+#define LRELPA_10_1PAIR			0x0002	/* 10Mbps 1 Pair capable       */
+
+/* LDS Expansion register. */
+#define LDSE_DOWNGRADE			0x8000	/* Can do LDS Speed Downgrade  */
+#define LDSE_MASTER			0x4000	/* Master / Slave              */
+#define LDSE_PAIRS_MASK			0x3000	/* Pair Count Mask             */
+#define LDSE_PAIRS_SHIFT		12
+#define LDSE_4PAIRS			(2 << LDSE_PAIRS_SHIFT)	/* 4 Pairs Connection */
+#define LDSE_2PAIRS			(1 << LDSE_PAIRS_SHIFT)	/* 2 Pairs Connection */
+#define LDSE_1PAIR			(0 << LDSE_PAIRS_SHIFT)	/* 1 Pair  Connection */
+#define LDSE_CABLEN_MASK		0x0FFF	/* Cable Length Mask           */
+
 /* BCM54810 Registers */
 #define BCM54810_EXP_BROADREACH_LRE_MISC_CTL	(MII_BCM54XX_EXP_SEL_ER + 0x90)
 #define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN	(1 << 0)
 #define BCM54810_SHD_CLK_CTL			0x3
 #define BCM54810_SHD_CLK_CTL_GTXCLK_EN		(1 << 9)
 
+/* BCM54811 Registers */
+#define BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL	(MII_BCM54XX_EXP_SEL_ER + 0x9A)
+/* Access Control Override Enable */
+#define BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL_EN		BIT(15)
+/* Access Control Override Value */
+#define BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL_OVERRIDE_VAL	BIT(14)
+/* Access Control Value */
+#define BCM54811_EXP_BROADREACH_LRE_OVERLAY_CTL_VAL		BIT(13)
+
 /* BCM54612E Registers */
 #define BCM54612E_EXP_SPARE0		(MII_BCM54XX_EXP_SEL_ETC + 0x34)
 #define BCM54612E_LED4_CLK125OUT_EN	(1 << 1)
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 230110b97029..4a0a6e703483 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -2054,6 +2054,7 @@ enum ethtool_link_mode_bit_indices {
 	ETHTOOL_LINK_MODE_10baseT1S_Full_BIT		 = 99,
 	ETHTOOL_LINK_MODE_10baseT1S_Half_BIT		 = 100,
 	ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT	 = 101,
+	ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT		 = 102,
 
 	/* must be last entry */
 	__ETHTOOL_LINK_MODE_MASK_NBITS
diff --git a/net/ethtool/common.c b/net/ethtool/common.c
index 67d06cd002a5..5f99a32e4fe5 100644
--- a/net/ethtool/common.c
+++ b/net/ethtool/common.c
@@ -211,6 +211,7 @@ const char link_mode_names[][ETH_GSTRING_LEN] = {
 	__DEFINE_LINK_MODE_NAME(10, T1S, Full),
 	__DEFINE_LINK_MODE_NAME(10, T1S, Half),
 	__DEFINE_LINK_MODE_NAME(10, T1S_P2MP, Half),
+	__DEFINE_LINK_MODE_NAME(10, T1BRR, Full),
 };
 static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
@@ -251,6 +252,7 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_T1S_P2MP	1
 #define __LINK_MODE_LANES_VR8		8
 #define __LINK_MODE_LANES_DR8_2		8
+#define __LINK_MODE_LANES_T1BRR		1
 
 #define __DEFINE_LINK_MODE_PARAMS(_speed, _type, _duplex)	\
 	[ETHTOOL_LINK_MODE(_speed, _type, _duplex)] = {		\
@@ -374,6 +376,7 @@ const struct link_mode_info link_mode_params[] = {
 	__DEFINE_LINK_MODE_PARAMS(10, T1S, Full),
 	__DEFINE_LINK_MODE_PARAMS(10, T1S, Half),
 	__DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half),
+	__DEFINE_LINK_MODE_PARAMS(10, T1BRR, Full),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);