iio: adc: Add support for PMIC7 ADC

The ADC architecture on PMIC7 is changed as compared to PMIC5. The
major change from PMIC5 is that all SW communication to ADC goes through
PMK8350, which communicates with other PMICs through PBS when the ADC
on PMK8350 works in master mode. The SID register is used to identify the
PMICs with which the PBS needs to communicate. Add support for the same.

Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

1 files changed, 212 insertions, 3 deletions

diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
index 0fa1d3707571..dcc7599e0f70 100644
--- a/drivers/iio/adc/qcom-spmi-adc5.c
+++ b/drivers/iio/adc/qcom-spmi-adc5.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, 2020, The Linux Foundation. All rights reserved.
  */
 
 #include <linux/bitops.h>
@@ -23,6 +23,7 @@
 
 #define ADC5_USR_REVISION1			0x0
 #define ADC5_USR_STATUS1			0x8
+#define ADC5_USR_STATUS1_CONV_FAULT		BIT(7)
 #define ADC5_USR_STATUS1_REQ_STS		BIT(1)
 #define ADC5_USR_STATUS1_EOC			BIT(0)
 #define ADC5_USR_STATUS1_REQ_STS_EOC_MASK	0x3
@@ -65,6 +66,9 @@
 
 #define ADC5_USR_IBAT_DATA1			0x53
 
+#define ADC_CHANNEL_OFFSET			0x8
+#define ADC_CHANNEL_MASK			GENMASK(7, 0)
+
 /*
  * Conversion time varies based on the decimation, clock rate, fast average
  * samples and measurements queued across different VADC peripherals.
@@ -79,6 +83,11 @@
 #define ADC5_HW_SETTLE_DIFF_MINOR		3
 #define ADC5_HW_SETTLE_DIFF_MAJOR		5
 
+/* For PMIC7 */
+#define ADC_APP_SID				0x40
+#define ADC_APP_SID_MASK			GENMASK(3, 0)
+#define ADC7_CONV_TIMEOUT			msecs_to_jiffies(10)
+
 enum adc5_cal_method {
 	ADC5_NO_CAL = 0,
 	ADC5_RATIOMETRIC_CAL,
@@ -96,6 +105,7 @@ enum adc5_cal_val {
  * @cal_method: calibration method.
  * @cal_val: calibration value
  * @decimation: sampling rate supported for the channel.
+ * @sid: slave id of PMIC owning the channel, for PMIC7.
  * @prescale: channel scaling performed on the input signal.
  * @hw_settle_time: the time between AMUX being configured and the
  *	start of conversion.
@@ -110,6 +120,7 @@ struct adc5_channel_prop {
 	enum adc5_cal_method	cal_method;
 	enum adc5_cal_val	cal_val;
 	unsigned int		decimation;
+	unsigned int		sid;
 	unsigned int		prescale;
 	unsigned int		hw_settle_time;
 	unsigned int		avg_samples;
@@ -165,6 +176,11 @@ static int adc5_write(struct adc5_chip *adc, u16 offset, u8 *data, int len)
 	return regmap_bulk_write(adc->regmap, adc->base + offset, data, len);
 }
 
+static int adc5_masked_write(struct adc5_chip *adc, u16 offset, u8 mask, u8 val)
+{
+	return regmap_update_bits(adc->regmap, adc->base + offset, mask, val);
+}
+
 static int adc5_prescaling_from_dt(u32 num, u32 den)
 {
 	unsigned int pre;
@@ -314,6 +330,47 @@ static int adc5_configure(struct adc5_chip *adc,
 	return adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
 }
 
+static int adc7_configure(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop)
+{
+	int ret;
+	u8 conv_req = 0, buf[4];
+
+	ret = adc5_masked_write(adc, ADC_APP_SID, ADC_APP_SID_MASK, prop->sid);
+	if (ret)
+		return ret;
+
+	ret = adc5_read(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	/* Digital param selection */
+	adc5_update_dig_param(adc, prop, &buf[0]);
+
+	/* Update fast average sample value */
+	buf[1] &= ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[1] |= prop->avg_samples;
+
+	/* Select ADC channel */
+	buf[2] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[3] &= ~ADC5_USR_HW_SETTLE_DELAY_MASK;
+	buf[3] |= prop->hw_settle_time;
+
+	/* Select CONV request */
+	conv_req = ADC5_USR_CONV_REQ_REQ;
+
+	if (!adc->poll_eoc)
+		reinit_completion(&adc->complete);
+
+	ret = adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	return adc5_write(adc, ADC5_USR_CONV_REQ, &conv_req, 1);
+}
+
 static int adc5_do_conversion(struct adc5_chip *adc,
 			struct adc5_channel_prop *prop,
 			struct iio_chan_spec const *chan,
@@ -355,6 +412,43 @@ unlock:
 	return ret;
 }
 
+static int adc7_do_conversion(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop,
+			struct iio_chan_spec const *chan,
+			u16 *data_volt, u16 *data_cur)
+{
+	int ret;
+	u8 status;
+
+	mutex_lock(&adc->lock);
+
+	ret = adc7_configure(adc, prop);
+	if (ret) {
+		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
+		goto unlock;
+	}
+
+	/* No support for polling mode at present */
+	wait_for_completion_timeout(&adc->complete, ADC7_CONV_TIMEOUT);
+
+	ret = adc5_read(adc, ADC5_USR_STATUS1, &status, 1);
+	if (ret)
+		goto unlock;
+
+	if (status & ADC5_USR_STATUS1_CONV_FAULT) {
+		dev_err(adc->dev, "Unexpected conversion fault\n");
+		ret = -EIO;
+		goto unlock;
+	}
+
+	ret = adc5_read_voltage_data(adc, data_volt);
+
+unlock:
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
 static irqreturn_t adc5_isr(int irq, void *dev_id)
 {
 	struct adc5_chip *adc = dev_id;
@@ -377,6 +471,22 @@ static int adc5_of_xlate(struct iio_dev *indio_dev,
 	return -EINVAL;
 }
 
+static int adc7_of_xlate(struct iio_dev *indio_dev,
+				const struct of_phandle_args *iiospec)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	int i, v_channel;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		v_channel = (adc->chan_props[i].sid << ADC_CHANNEL_OFFSET) |
+			adc->chan_props[i].channel;
+		if (v_channel == iiospec->args[0])
+			return i;
+	}
+
+	return -EINVAL;
+}
+
 static int adc5_read_raw(struct iio_dev *indio_dev,
 			 struct iio_chan_spec const *chan, int *val, int *val2,
 			 long mask)
@@ -410,11 +520,48 @@ static int adc5_read_raw(struct iio_dev *indio_dev,
 	return 0;
 }
 
+static int adc7_read_raw(struct iio_dev *indio_dev,
+			 struct iio_chan_spec const *chan, int *val, int *val2,
+			 long mask)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+	u16 adc_code_volt, adc_code_cur;
+	int ret;
+
+	prop = &adc->chan_props[chan->address];
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = adc7_do_conversion(adc, prop, chan,
+					&adc_code_volt, &adc_code_cur);
+		if (ret)
+			return ret;
+
+		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
+			&adc5_prescale_ratios[prop->prescale],
+			adc->data,
+			adc_code_volt, val);
+
+		if (ret)
+			return ret;
+
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
 static const struct iio_info adc5_info = {
 	.read_raw = adc5_read_raw,
 	.of_xlate = adc5_of_xlate,
 };
 
+static const struct iio_info adc7_info = {
+	.read_raw = adc7_read_raw,
+	.of_xlate = adc7_of_xlate,
+};
+
 struct adc5_channels {
 	const char *datasheet_name;
 	unsigned int prescale_index;
@@ -477,6 +624,39 @@ static const struct adc5_channels adc5_chans_pmic[ADC5_MAX_CHANNEL] = {
 					SCALE_HW_CALIB_PM5_SMB_TEMP)
 };
 
+static const struct adc5_channels adc7_chans_pmic[ADC5_MAX_CHANNEL] = {
+	[ADC7_REF_GND]		= ADC5_CHAN_VOLT("ref_gnd", 0,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_1P25VREF]		= ADC5_CHAN_VOLT("vref_1p25", 0,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_VPH_PWR]		= ADC5_CHAN_VOLT("vph_pwr", 1,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_VBAT_SNS]		= ADC5_CHAN_VOLT("vbat_sns", 3,
+					SCALE_HW_CALIB_DEFAULT)
+	[ADC7_DIE_TEMP]		= ADC5_CHAN_TEMP("die_temp", 0,
+					SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC7_AMUX_THM1_100K_PU] = ADC5_CHAN_TEMP("amux_thm1_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM2_100K_PU] = ADC5_CHAN_TEMP("amux_thm2_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM3_100K_PU] = ADC5_CHAN_TEMP("amux_thm3_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM4_100K_PU] = ADC5_CHAN_TEMP("amux_thm4_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM5_100K_PU] = ADC5_CHAN_TEMP("amux_thm5_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_AMUX_THM6_100K_PU] = ADC5_CHAN_TEMP("amux_thm6_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO1_100K_PU]	= ADC5_CHAN_TEMP("gpio1_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO2_100K_PU]	= ADC5_CHAN_TEMP("gpio2_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO3_100K_PU]	= ADC5_CHAN_TEMP("gpio3_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC7_GPIO4_100K_PU]	= ADC5_CHAN_TEMP("gpio4_pu2", 0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+};
+
 static const struct adc5_channels adc5_chans_rev2[ADC5_MAX_CHANNEL] = {
 	[ADC5_REF_GND]		= ADC5_CHAN_VOLT("ref_gnd", 0,
 					SCALE_HW_CALIB_DEFAULT)
@@ -511,6 +691,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 {
 	const char *name = node->name, *channel_name;
 	u32 chan, value, varr[2];
+	u32 sid = 0;
 	int ret;
 	struct device *dev = adc->dev;
 
@@ -520,6 +701,15 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 		return ret;
 	}
 
+	/* Value read from "reg" is virtual channel number */
+
+	/* virtual channel number = sid << 8 | channel number */
+
+	if (adc->data->info == &adc7_info) {
+		sid = chan >> ADC_CHANNEL_OFFSET;
+		chan = chan & ADC_CHANNEL_MASK;
+	}
+
 	if (chan > ADC5_PARALLEL_ISENSE_VBAT_IDATA ||
 	    !data->adc_chans[chan].datasheet_name) {
 		dev_err(dev, "%s invalid channel number %d\n", name, chan);
@@ -528,6 +718,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 
 	/* the channel has DT description */
 	prop->channel = chan;
+	prop->sid = sid;
 
 	channel_name = of_get_property(node,
 				"label", NULL) ? : node->name;
@@ -578,8 +769,9 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
 		pr_debug("dig_ver:minor:%d, major:%d\n", dig_version[0],
 						dig_version[1]);
 		/* Digital controller >= 5.3 have hw_settle_2 option */
-		if (dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
-			dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR)
+		if ((dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
+			dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR) ||
+			adc->data->info == &adc7_info)
 			ret = adc5_hw_settle_time_from_dt(value,
 							data->hw_settle_2);
 		else
@@ -640,6 +832,18 @@ static const struct adc5_data adc5_data_pmic = {
 				1, 2, 4, 8, 16, 32, 64, 128},
 };
 
+static const struct adc5_data adc7_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.adc_chans = adc7_chans_pmic,
+	.info = &adc7_info,
+	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
+				{85, 340, 1360},
+	.hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
+				{15, 100, 200, 300, 400, 500, 600, 700,
+				1000, 2000, 4000, 8000, 16000, 32000,
+				64000, 128000},
+};
+
 static const struct adc5_data adc5_data_pmic_rev2 = {
 	.full_scale_code_volt = 0x4000,
 	.full_scale_code_cur = 0x1800,
@@ -661,6 +865,10 @@ static const struct of_device_id adc5_match_table[] = {
 		.data = &adc5_data_pmic,
 	},
 	{
+		.compatible = "qcom,spmi-adc7",
+		.data = &adc7_data_pmic,
+	},
+	{
 		.compatible = "qcom,spmi-adc-rev2",
 		.data = &adc5_data_pmic_rev2,
 	},
@@ -754,6 +962,7 @@ static int adc5_probe(struct platform_device *pdev)
 	adc->regmap = regmap;
 	adc->dev = dev;
 	adc->base = reg;
+
 	init_completion(&adc->complete);
 	mutex_init(&adc->lock);