diff options
| -rw-r--r-- | drivers/net/ethernet/marvell/mvneta.c | 107 | ||||
| -rw-r--r-- | drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 5 | ||||
| -rw-r--r-- | drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 86 | ||||
| -rw-r--r-- | drivers/net/ethernet/microchip/lan743x_ethtool.c | 21 | ||||
| -rw-r--r-- | drivers/net/ethernet/microchip/lan743x_main.c | 46 | ||||
| -rw-r--r-- | drivers/net/ethernet/microchip/lan743x_main.h | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 57 | ||||
| -rw-r--r-- | drivers/net/phy/phy.c | 20 | ||||
| -rw-r--r-- | drivers/net/phy/phylink.c | 149 | ||||
| -rw-r--r-- | include/linux/phy.h | 1 | ||||
| -rw-r--r-- | include/linux/phylink.h | 45 | ||||
| -rw-r--r-- | include/uapi/linux/mdio.h | 1 |
12 files changed, 446 insertions, 93 deletions
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c index aa049cee576d..82f4333fb426 100644 --- a/drivers/net/ethernet/marvell/mvneta.c +++ b/drivers/net/ethernet/marvell/mvneta.c @@ -284,8 +284,12 @@ MVNETA_TXQ_BUCKET_REFILL_PERIOD)) #define MVNETA_LPI_CTRL_0 0x2cc0 +#define MVNETA_LPI_CTRL_0_TS (0xff << 8) #define MVNETA_LPI_CTRL_1 0x2cc4 -#define MVNETA_LPI_REQUEST_ENABLE BIT(0) +#define MVNETA_LPI_CTRL_1_REQUEST_ENABLE BIT(0) +#define MVNETA_LPI_CTRL_1_REQUEST_FORCE BIT(1) +#define MVNETA_LPI_CTRL_1_MANUAL_MODE BIT(2) +#define MVNETA_LPI_CTRL_1_TW (0xfff << 4) #define MVNETA_LPI_CTRL_2 0x2cc8 #define MVNETA_LPI_STATUS 0x2ccc @@ -541,10 +545,6 @@ struct mvneta_port { struct mvneta_bm_pool *pool_short; int bm_win_id; - bool eee_enabled; - bool eee_active; - bool tx_lpi_enabled; - u64 ethtool_stats[ARRAY_SIZE(mvneta_statistics)]; u32 indir[MVNETA_RSS_LU_TABLE_SIZE]; @@ -4213,18 +4213,6 @@ static int mvneta_mac_finish(struct phylink_config *config, unsigned int mode, return 0; } -static void mvneta_set_eee(struct mvneta_port *pp, bool enable) -{ - u32 lpi_ctl1; - - lpi_ctl1 = mvreg_read(pp, MVNETA_LPI_CTRL_1); - if (enable) - lpi_ctl1 |= MVNETA_LPI_REQUEST_ENABLE; - else - lpi_ctl1 &= ~MVNETA_LPI_REQUEST_ENABLE; - mvreg_write(pp, MVNETA_LPI_CTRL_1, lpi_ctl1); -} - static void mvneta_mac_link_down(struct phylink_config *config, unsigned int mode, phy_interface_t interface) { @@ -4240,9 +4228,6 @@ static void mvneta_mac_link_down(struct phylink_config *config, val |= MVNETA_GMAC_FORCE_LINK_DOWN; mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val); } - - pp->eee_active = false; - mvneta_set_eee(pp, false); } static void mvneta_mac_link_up(struct phylink_config *config, @@ -4291,11 +4276,56 @@ static void mvneta_mac_link_up(struct phylink_config *config, } mvneta_port_up(pp); +} - if (phy && pp->eee_enabled) { - pp->eee_active = phy_init_eee(phy, false) >= 0; - mvneta_set_eee(pp, pp->eee_active && pp->tx_lpi_enabled); +static void mvneta_mac_disable_tx_lpi(struct phylink_config *config) +{ + struct mvneta_port *pp = netdev_priv(to_net_dev(config->dev)); + u32 lpi1; + + lpi1 = mvreg_read(pp, MVNETA_LPI_CTRL_1); + lpi1 &= ~(MVNETA_LPI_CTRL_1_REQUEST_ENABLE | + MVNETA_LPI_CTRL_1_REQUEST_FORCE | + MVNETA_LPI_CTRL_1_MANUAL_MODE); + mvreg_write(pp, MVNETA_LPI_CTRL_1, lpi1); +} + +static int mvneta_mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop) +{ + struct mvneta_port *pp = netdev_priv(to_net_dev(config->dev)); + u32 ts, tw, lpi0, lpi1, status; + + status = mvreg_read(pp, MVNETA_GMAC_STATUS); + if (status & MVNETA_GMAC_SPEED_1000) { + /* At 1G speeds, the timer resolution are 1us, and + * 802.3 says tw is 16.5us. Round up to 17us. + */ + tw = 17; + ts = timer; + } else { + /* At 100M speeds, the timer resolutions are 10us, and + * 802.3 says tw is 30us. + */ + tw = 3; + ts = DIV_ROUND_UP(timer, 10); } + + if (ts > 255) + ts = 255; + + /* Configure ts */ + lpi0 = mvreg_read(pp, MVNETA_LPI_CTRL_0); + lpi0 = u32_replace_bits(lpi0, ts, MVNETA_LPI_CTRL_0_TS); + mvreg_write(pp, MVNETA_LPI_CTRL_0, lpi0); + + /* Configure tw and enable LPI generation */ + lpi1 = mvreg_read(pp, MVNETA_LPI_CTRL_1); + lpi1 = u32_replace_bits(lpi1, tw, MVNETA_LPI_CTRL_1_TW); + lpi1 |= MVNETA_LPI_CTRL_1_REQUEST_ENABLE; + mvreg_write(pp, MVNETA_LPI_CTRL_1, lpi1); + + return 0; } static const struct phylink_mac_ops mvneta_phylink_ops = { @@ -4305,6 +4335,8 @@ static const struct phylink_mac_ops mvneta_phylink_ops = { .mac_finish = mvneta_mac_finish, .mac_link_down = mvneta_mac_link_down, .mac_link_up = mvneta_mac_link_up, + .mac_disable_tx_lpi = mvneta_mac_disable_tx_lpi, + .mac_enable_tx_lpi = mvneta_mac_enable_tx_lpi, }; static int mvneta_mdio_probe(struct mvneta_port *pp) @@ -5109,14 +5141,6 @@ static int mvneta_ethtool_get_eee(struct net_device *dev, struct ethtool_keee *eee) { struct mvneta_port *pp = netdev_priv(dev); - u32 lpi_ctl0; - - lpi_ctl0 = mvreg_read(pp, MVNETA_LPI_CTRL_0); - - eee->eee_enabled = pp->eee_enabled; - eee->eee_active = pp->eee_active; - eee->tx_lpi_enabled = pp->tx_lpi_enabled; - eee->tx_lpi_timer = (lpi_ctl0) >> 8; // * scale; return phylink_ethtool_get_eee(pp->phylink, eee); } @@ -5125,7 +5149,6 @@ static int mvneta_ethtool_set_eee(struct net_device *dev, struct ethtool_keee *eee) { struct mvneta_port *pp = netdev_priv(dev); - u32 lpi_ctl0; /* The Armada 37x documents do not give limits for this other than * it being an 8-bit register. @@ -5133,16 +5156,6 @@ static int mvneta_ethtool_set_eee(struct net_device *dev, if (eee->tx_lpi_enabled && eee->tx_lpi_timer > 255) return -EINVAL; - lpi_ctl0 = mvreg_read(pp, MVNETA_LPI_CTRL_0); - lpi_ctl0 &= ~(0xff << 8); - lpi_ctl0 |= eee->tx_lpi_timer << 8; - mvreg_write(pp, MVNETA_LPI_CTRL_0, lpi_ctl0); - - pp->eee_enabled = eee->eee_enabled; - pp->tx_lpi_enabled = eee->tx_lpi_enabled; - - mvneta_set_eee(pp, eee->tx_lpi_enabled && eee->eee_enabled); - return phylink_ethtool_set_eee(pp->phylink, eee); } @@ -5456,6 +5469,9 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode) !phy_interface_mode_is_rgmii(phy_mode)) return -EINVAL; + /* Ensure LPI is disabled */ + mvneta_mac_disable_tx_lpi(&pp->phylink_config); + return 0; } @@ -5547,6 +5563,13 @@ static int mvneta_probe(struct platform_device *pdev) pp->phylink_config.mac_capabilities = MAC_SYM_PAUSE | MAC_10 | MAC_100 | MAC_1000FD | MAC_2500FD; + /* Setup EEE. Choose 250us idle. Only supported in SGMII modes. */ + __set_bit(PHY_INTERFACE_MODE_QSGMII, pp->phylink_config.lpi_interfaces); + __set_bit(PHY_INTERFACE_MODE_SGMII, pp->phylink_config.lpi_interfaces); + pp->phylink_config.lpi_capabilities = MAC_100FD | MAC_1000FD; + pp->phylink_config.lpi_timer_default = 250; + pp->phylink_config.eee_enabled_default = true; + phy_interface_set_rgmii(pp->phylink_config.supported_interfaces); __set_bit(PHY_INTERFACE_MODE_QSGMII, pp->phylink_config.supported_interfaces); diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h index 9e02e4367bec..44fe9b68d1c2 100644 --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h @@ -481,6 +481,11 @@ #define MVPP22_GMAC_INT_SUM_MASK 0xa4 #define MVPP22_GMAC_INT_SUM_MASK_LINK_STAT BIT(1) #define MVPP22_GMAC_INT_SUM_MASK_PTP BIT(2) +#define MVPP2_GMAC_LPI_CTRL0 0xc0 +#define MVPP2_GMAC_LPI_CTRL0_TS_MASK GENMASK(15, 8) +#define MVPP2_GMAC_LPI_CTRL1 0xc4 +#define MVPP2_GMAC_LPI_CTRL1_REQ_EN BIT(0) +#define MVPP2_GMAC_LPI_CTRL1_TW_MASK GENMASK(15, 4) /* Per-port XGMAC registers. PPv2.2 and PPv2.3, only for GOP port 0, * relative to port->base. diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c index d294580f4832..dd76c1b7ed3a 100644 --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c @@ -5757,6 +5757,28 @@ static int mvpp2_ethtool_set_rxfh(struct net_device *dev, return mvpp2_modify_rxfh_context(dev, NULL, rxfh, extack); } +static int mvpp2_ethtool_get_eee(struct net_device *dev, + struct ethtool_keee *eee) +{ + struct mvpp2_port *port = netdev_priv(dev); + + if (!port->phylink) + return -EOPNOTSUPP; + + return phylink_ethtool_get_eee(port->phylink, eee); +} + +static int mvpp2_ethtool_set_eee(struct net_device *dev, + struct ethtool_keee *eee) +{ + struct mvpp2_port *port = netdev_priv(dev); + + if (!port->phylink) + return -EOPNOTSUPP; + + return phylink_ethtool_set_eee(port->phylink, eee); +} + /* Device ops */ static const struct net_device_ops mvpp2_netdev_ops = { @@ -5802,6 +5824,8 @@ static const struct ethtool_ops mvpp2_eth_tool_ops = { .create_rxfh_context = mvpp2_create_rxfh_context, .modify_rxfh_context = mvpp2_modify_rxfh_context, .remove_rxfh_context = mvpp2_remove_rxfh_context, + .get_eee = mvpp2_ethtool_get_eee, + .set_eee = mvpp2_ethtool_set_eee, }; /* Used for PPv2.1, or PPv2.2 with the old Device Tree binding that @@ -6674,6 +6698,55 @@ static void mvpp2_mac_link_down(struct phylink_config *config, mvpp2_port_disable(port); } +static void mvpp2_mac_disable_tx_lpi(struct phylink_config *config) +{ + struct mvpp2_port *port = mvpp2_phylink_to_port(config); + + mvpp2_modify(port->base + MVPP2_GMAC_LPI_CTRL1, + MVPP2_GMAC_LPI_CTRL1_REQ_EN, 0); +} + +static int mvpp2_mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop) +{ + struct mvpp2_port *port = mvpp2_phylink_to_port(config); + u32 ts, tw, lpi1, status; + + status = readl(port->base + MVPP2_GMAC_STATUS0); + if (status & MVPP2_GMAC_STATUS0_GMII_SPEED) { + /* At 1G speeds, the timer resolution are 1us, and + * 802.3 says tw is 16.5us. Round up to 17us. + */ + tw = 17; + ts = timer; + } else { + /* At 100M speeds, the timer resolutions are 10us, and + * 802.3 says tw is 30us. + */ + tw = 3; + ts = DIV_ROUND_UP(timer, 10); + } + + if (ts > 255) + ts = 255; + + /* Configure ts */ + mvpp2_modify(port->base + MVPP2_GMAC_LPI_CTRL0, + MVPP2_GMAC_LPI_CTRL0_TS_MASK, + FIELD_PREP(MVPP2_GMAC_LPI_CTRL0_TS_MASK, ts)); + + lpi1 = readl(port->base + MVPP2_GMAC_LPI_CTRL1); + + /* Configure tw */ + lpi1 = u32_replace_bits(lpi1, tw, MVPP2_GMAC_LPI_CTRL1_TW_MASK); + + /* Enable LPI generation */ + writel(lpi1 | MVPP2_GMAC_LPI_CTRL1_REQ_EN, + port->base + MVPP2_GMAC_LPI_CTRL1); + + return 0; +} + static const struct phylink_mac_ops mvpp2_phylink_ops = { .mac_select_pcs = mvpp2_select_pcs, .mac_prepare = mvpp2_mac_prepare, @@ -6681,6 +6754,8 @@ static const struct phylink_mac_ops mvpp2_phylink_ops = { .mac_finish = mvpp2_mac_finish, .mac_link_up = mvpp2_mac_link_up, .mac_link_down = mvpp2_mac_link_down, + .mac_enable_tx_lpi = mvpp2_mac_enable_tx_lpi, + .mac_disable_tx_lpi = mvpp2_mac_disable_tx_lpi, }; /* Work-around for ACPI */ @@ -6959,6 +7034,15 @@ static int mvpp2_port_probe(struct platform_device *pdev, port->phylink_config.mac_capabilities = MAC_2500FD | MAC_1000FD | MAC_100 | MAC_10; + __set_bit(PHY_INTERFACE_MODE_SGMII, + port->phylink_config.lpi_interfaces); + + port->phylink_config.lpi_capabilities = MAC_1000FD | MAC_100FD; + + /* Setup EEE. Choose 250us idle. */ + port->phylink_config.lpi_timer_default = 250; + port->phylink_config.eee_enabled_default = true; + if (port->priv->global_tx_fc) port->phylink_config.mac_capabilities |= MAC_SYM_PAUSE | MAC_ASYM_PAUSE; @@ -7033,6 +7117,8 @@ static int mvpp2_port_probe(struct platform_device *pdev, goto err_free_port_pcpu; } port->phylink = phylink; + + mvpp2_mac_disable_tx_lpi(&port->phylink_config); } else { dev_warn(&pdev->dev, "Use link irqs for port#%d. FW update required\n", port->id); port->phylink = NULL; diff --git a/drivers/net/ethernet/microchip/lan743x_ethtool.c b/drivers/net/ethernet/microchip/lan743x_ethtool.c index 1a1cbd034eda..1459acfb1e61 100644 --- a/drivers/net/ethernet/microchip/lan743x_ethtool.c +++ b/drivers/net/ethernet/microchip/lan743x_ethtool.c @@ -1055,9 +1055,6 @@ static int lan743x_ethtool_get_eee(struct net_device *netdev, { struct lan743x_adapter *adapter = netdev_priv(netdev); - eee->tx_lpi_timer = lan743x_csr_read(adapter, - MAC_EEE_TX_LPI_REQ_DLY_CNT); - return phylink_ethtool_get_eee(adapter->phylink, eee); } @@ -1065,24 +1062,6 @@ static int lan743x_ethtool_set_eee(struct net_device *netdev, struct ethtool_keee *eee) { struct lan743x_adapter *adapter = netdev_priv(netdev); - u32 tx_lpi_timer; - - tx_lpi_timer = lan743x_csr_read(adapter, MAC_EEE_TX_LPI_REQ_DLY_CNT); - if (tx_lpi_timer != eee->tx_lpi_timer) { - u32 mac_cr = lan743x_csr_read(adapter, MAC_CR); - - /* Software should only change this field when Energy Efficient - * Ethernet Enable (EEEEN) is cleared. - * This function will trigger an autonegotiation restart and - * eee will be reenabled during link up if eee was negotiated. - */ - lan743x_mac_eee_enable(adapter, false); - lan743x_csr_write(adapter, MAC_EEE_TX_LPI_REQ_DLY_CNT, - eee->tx_lpi_timer); - - if (mac_cr & MAC_CR_EEE_EN_) - lan743x_mac_eee_enable(adapter, true); - } return phylink_ethtool_set_eee(adapter->phylink, eee); } diff --git a/drivers/net/ethernet/microchip/lan743x_main.c b/drivers/net/ethernet/microchip/lan743x_main.c index 4dc5adcda6a3..23760b613d3e 100644 --- a/drivers/net/ethernet/microchip/lan743x_main.c +++ b/drivers/net/ethernet/microchip/lan743x_main.c @@ -2966,7 +2966,7 @@ static int lan743x_phylink_2500basex_config(struct lan743x_adapter *adapter) return lan743x_pcs_power_reset(adapter); } -void lan743x_mac_eee_enable(struct lan743x_adapter *adapter, bool enable) +static void lan743x_mac_eee_enable(struct lan743x_adapter *adapter, bool enable) { u32 mac_cr; @@ -3027,10 +3027,8 @@ static void lan743x_phylink_mac_link_down(struct phylink_config *config, phy_interface_t interface) { struct net_device *netdev = to_net_dev(config->dev); - struct lan743x_adapter *adapter = netdev_priv(netdev); - netif_tx_stop_all_queues(to_net_dev(config->dev)); - lan743x_mac_eee_enable(adapter, false); + netif_tx_stop_all_queues(netdev); } static void lan743x_phylink_mac_link_up(struct phylink_config *config, @@ -3072,16 +3070,40 @@ static void lan743x_phylink_mac_link_up(struct phylink_config *config, cap & FLOW_CTRL_TX, cap & FLOW_CTRL_RX); - if (phydev) - lan743x_mac_eee_enable(adapter, phydev->enable_tx_lpi); - netif_tx_wake_all_queues(netdev); } +static void lan743x_mac_disable_tx_lpi(struct phylink_config *config) +{ + struct net_device *netdev = to_net_dev(config->dev); + struct lan743x_adapter *adapter = netdev_priv(netdev); + + lan743x_mac_eee_enable(adapter, false); +} + +static int lan743x_mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop) +{ + struct net_device *netdev = to_net_dev(config->dev); + struct lan743x_adapter *adapter = netdev_priv(netdev); + + /* Software should only change this field when Energy Efficient + * Ethernet Enable (EEEEN) is cleared. We ensure that by clearing + * EEEEN during probe, and phylink itself guarantees that + * mac_disable_tx_lpi() will have been previously called. + */ + lan743x_csr_write(adapter, MAC_EEE_TX_LPI_REQ_DLY_CNT, timer); + lan743x_mac_eee_enable(adapter, true); + + return 0; +} + static const struct phylink_mac_ops lan743x_phylink_mac_ops = { .mac_config = lan743x_phylink_mac_config, .mac_link_down = lan743x_phylink_mac_link_down, .mac_link_up = lan743x_phylink_mac_link_up, + .mac_disable_tx_lpi = lan743x_mac_disable_tx_lpi, + .mac_enable_tx_lpi = lan743x_mac_enable_tx_lpi, }; static int lan743x_phylink_create(struct lan743x_adapter *adapter) @@ -3095,6 +3117,9 @@ static int lan743x_phylink_create(struct lan743x_adapter *adapter) adapter->phylink_config.mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | MAC_10 | MAC_100 | MAC_1000FD; + adapter->phylink_config.lpi_capabilities = MAC_100FD | MAC_1000FD; + adapter->phylink_config.lpi_timer_default = + lan743x_csr_read(adapter, MAC_EEE_TX_LPI_REQ_DLY_CNT); lan743x_phy_interface_select(adapter); @@ -3120,6 +3145,10 @@ static int lan743x_phylink_create(struct lan743x_adapter *adapter) phy_interface_set_rgmii(adapter->phylink_config.supported_interfaces); } + memcpy(adapter->phylink_config.lpi_interfaces, + adapter->phylink_config.supported_interfaces, + sizeof(adapter->phylink_config.lpi_interfaces)); + pl = phylink_create(&adapter->phylink_config, NULL, adapter->phy_interface, &lan743x_phylink_mac_ops); @@ -3517,6 +3546,9 @@ static int lan743x_hardware_init(struct lan743x_adapter *adapter, spin_lock_init(&tx->ring_lock); } + /* Ensure EEEEN is clear */ + lan743x_mac_eee_enable(adapter, false); + return 0; } diff --git a/drivers/net/ethernet/microchip/lan743x_main.h b/drivers/net/ethernet/microchip/lan743x_main.h index 8ef897c114d3..7f73d66854be 100644 --- a/drivers/net/ethernet/microchip/lan743x_main.h +++ b/drivers/net/ethernet/microchip/lan743x_main.h @@ -1206,6 +1206,5 @@ void lan743x_hs_syslock_release(struct lan743x_adapter *adapter); void lan743x_mac_flow_ctrl_set_enables(struct lan743x_adapter *adapter, bool tx_enable, bool rx_enable); int lan743x_sgmii_read(struct lan743x_adapter *adapter, u8 mmd, u16 addr); -void lan743x_mac_eee_enable(struct lan743x_adapter *adapter, bool enable); #endif /* _LAN743X_H */ diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 49b41148d594..d99ad77a8005 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -988,8 +988,8 @@ static void stmmac_mac_link_down(struct phylink_config *config, struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev)); stmmac_mac_set(priv, priv->ioaddr, false); - stmmac_eee_init(priv, false); - stmmac_set_eee_pls(priv, priv->hw, false); + if (priv->dma_cap.eee) + stmmac_set_eee_pls(priv, priv->hw, false); if (stmmac_fpe_supported(priv)) stmmac_fpe_link_state_handle(priv, false); @@ -1096,13 +1096,8 @@ static void stmmac_mac_link_up(struct phylink_config *config, writel(ctrl, priv->ioaddr + MAC_CTRL_REG); stmmac_mac_set(priv, priv->ioaddr, true); - if (phy && priv->dma_cap.eee) { - phy_eee_rx_clock_stop(phy, !(priv->plat->flags & - STMMAC_FLAG_RX_CLK_RUNS_IN_LPI)); - priv->tx_lpi_timer = phy->eee_cfg.tx_lpi_timer; - stmmac_eee_init(priv, phy->enable_tx_lpi); + if (priv->dma_cap.eee) stmmac_set_eee_pls(priv, priv->hw, true); - } if (stmmac_fpe_supported(priv)) stmmac_fpe_link_state_handle(priv, true); @@ -1111,12 +1106,32 @@ static void stmmac_mac_link_up(struct phylink_config *config, stmmac_hwtstamp_correct_latency(priv, priv); } +static void stmmac_mac_disable_tx_lpi(struct phylink_config *config) +{ + struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev)); + + stmmac_eee_init(priv, false); +} + +static int stmmac_mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop) +{ + struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev)); + + priv->tx_lpi_timer = timer; + stmmac_eee_init(priv, true); + + return 0; +} + static const struct phylink_mac_ops stmmac_phylink_mac_ops = { .mac_get_caps = stmmac_mac_get_caps, .mac_select_pcs = stmmac_mac_select_pcs, .mac_config = stmmac_mac_config, .mac_link_down = stmmac_mac_link_down, .mac_link_up = stmmac_mac_link_up, + .mac_disable_tx_lpi = stmmac_mac_disable_tx_lpi, + .mac_enable_tx_lpi = stmmac_mac_enable_tx_lpi, }; /** @@ -1189,9 +1204,6 @@ static int stmmac_init_phy(struct net_device *dev) return -ENODEV; } - if (priv->dma_cap.eee) - phy_support_eee(phydev); - ret = phylink_connect_phy(priv->phylink, phydev); } else { fwnode_handle_put(phy_fwnode); @@ -1201,7 +1213,12 @@ static int stmmac_init_phy(struct net_device *dev) if (ret == 0) { struct ethtool_keee eee; - /* Configure phylib's copy of the LPI timer */ + /* Configure phylib's copy of the LPI timer. Normally, + * phylink_config.lpi_timer_default would do this, but there is + * a chance that userspace could change the eee_timer setting + * via sysfs before the first open. Thus, preserve existing + * behaviour. + */ if (!phylink_ethtool_get_eee(priv->phylink, &eee)) { eee.tx_lpi_timer = priv->tx_lpi_timer; phylink_ethtool_set_eee(priv->phylink, &eee); @@ -1234,6 +1251,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) /* Stmmac always requires an RX clock for hardware initialization */ priv->phylink_config.mac_requires_rxc = true; + if (!(priv->plat->flags & STMMAC_FLAG_RX_CLK_RUNS_IN_LPI)) + priv->phylink_config.eee_rx_clk_stop_enable = true; + mdio_bus_data = priv->plat->mdio_bus_data; if (mdio_bus_data) priv->phylink_config.default_an_inband = @@ -1255,6 +1275,19 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.supported_interfaces, pcs->supported_interfaces); + if (priv->dma_cap.eee) { + /* Assume all supported interfaces also support LPI */ + memcpy(priv->phylink_config.lpi_interfaces, + priv->phylink_config.supported_interfaces, + sizeof(priv->phylink_config.lpi_interfaces)); + + /* All full duplex speeds above 100Mbps are supported */ + priv->phylink_config.lpi_capabilities = ~(MAC_1000FD - 1) | + MAC_100FD; + priv->phylink_config.lpi_timer_default = eee_timer * 1000; + priv->phylink_config.eee_enabled_default = true; + } + fwnode = priv->plat->port_node; if (!fwnode) fwnode = dev_fwnode(priv->device); diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index c008fe050245..d0c1718e2b16 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -1704,6 +1704,26 @@ void phy_mac_interrupt(struct phy_device *phydev) EXPORT_SYMBOL(phy_mac_interrupt); /** + * phy_eee_tx_clock_stop_capable() - indicate whether the MAC can stop tx clock + * @phydev: target phy_device struct + * + * Indicate whether the MAC can disable the transmit xMII clock while in LPI + * state. Returns 1 if the MAC may stop the transmit clock, 0 if the MAC must + * not stop the transmit clock, or negative error. + */ +int phy_eee_tx_clock_stop_capable(struct phy_device *phydev) +{ + int stat1; + + stat1 = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_STAT1); + if (stat1 < 0) + return stat1; + + return !!(stat1 & MDIO_PCS_STAT1_CLKSTOP_CAP); +} +EXPORT_SYMBOL_GPL(phy_eee_tx_clock_stop_capable); + +/** * phy_eee_rx_clock_stop() - configure PHY receive clock in LPI * @phydev: target phy_device struct * @clk_stop_enable: flag to indicate whether the clock can be stopped diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c index ff0efb52189f..66eea3f963d3 100644 --- a/drivers/net/phy/phylink.c +++ b/drivers/net/phy/phylink.c @@ -60,6 +60,7 @@ struct phylink { u8 act_link_an_mode; /* Active MLO_AN_xxx mode */ u8 link_port; /* The current non-phy ethtool port */ __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); + __ETHTOOL_DECLARE_LINK_MODE_MASK(supported_lpi); /* The link configuration settings */ struct phylink_link_state link_config; @@ -81,12 +82,20 @@ struct phylink { unsigned int pcs_state; bool link_failed; + bool mac_supports_eee_ops; + bool mac_supports_eee; + bool phy_enable_tx_lpi; + bool mac_enable_tx_lpi; + bool mac_tx_clk_stop; + u32 mac_tx_lpi_timer; struct sfp_bus *sfp_bus; bool sfp_may_have_phy; DECLARE_PHY_INTERFACE_MASK(sfp_interfaces); __ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support); u8 sfp_port; + + struct eee_config eee_cfg; }; #define phylink_printk(level, pl, fmt, ...) \ @@ -1584,6 +1593,39 @@ static const char *phylink_pause_to_str(int pause) } } +static void phylink_deactivate_lpi(struct phylink *pl) +{ + if (pl->mac_enable_tx_lpi) { + pl->mac_enable_tx_lpi = false; + + phylink_dbg(pl, "disabling LPI\n"); + + pl->mac_ops->mac_disable_tx_lpi(pl->config); + } +} + +static void phylink_activate_lpi(struct phylink *pl) +{ + int err; + + if (!test_bit(pl->cur_interface, pl->config->lpi_interfaces)) { + phylink_dbg(pl, "MAC does not support LPI with %s\n", + phy_modes(pl->cur_interface)); + return; + } + + phylink_dbg(pl, "LPI timer %uus, tx clock stop %u\n", + pl->mac_tx_lpi_timer, pl->mac_tx_clk_stop); + + err = pl->mac_ops->mac_enable_tx_lpi(pl->config, pl->mac_tx_lpi_timer, + pl->mac_tx_clk_stop); + if (!err) + pl->mac_enable_tx_lpi = true; + else + phylink_err(pl, "%ps() failed: %pe\n", + pl->mac_ops->mac_enable_tx_lpi, ERR_PTR(err)); +} + static void phylink_link_up(struct phylink *pl, struct phylink_link_state link_state) { @@ -1630,6 +1672,9 @@ static void phylink_link_up(struct phylink *pl, pl->cur_interface, speed, duplex, !!(link_state.pause & MLO_PAUSE_TX), rx_pause); + if (pl->mac_supports_eee && pl->phy_enable_tx_lpi) + phylink_activate_lpi(pl); + if (ndev) netif_carrier_on(ndev); @@ -1646,25 +1691,29 @@ static void phylink_link_down(struct phylink *pl) if (ndev) netif_carrier_off(ndev); + + phylink_deactivate_lpi(pl); + pl->mac_ops->mac_link_down(pl->config, pl->act_link_an_mode, pl->cur_interface); phylink_info(pl, "Link is Down\n"); } +static bool phylink_link_is_up(struct phylink *pl) +{ + return pl->netdev ? netif_carrier_ok(pl->netdev) : pl->old_link_state; +} + static void phylink_resolve(struct work_struct *w) { struct phylink *pl = container_of(w, struct phylink, resolve); struct phylink_link_state link_state; - struct net_device *ndev = pl->netdev; bool mac_config = false; bool retrigger = false; bool cur_link_state; mutex_lock(&pl->state_mutex); - if (pl->netdev) - cur_link_state = netif_carrier_ok(ndev); - else - cur_link_state = pl->old_link_state; + cur_link_state = phylink_link_is_up(pl); if (pl->phylink_disable_state) { pl->link_failed = false; @@ -1908,6 +1957,17 @@ struct phylink *phylink_create(struct phylink_config *config, return ERR_PTR(-EINVAL); } + pl->mac_supports_eee_ops = mac_ops->mac_disable_tx_lpi && + mac_ops->mac_enable_tx_lpi; + pl->mac_supports_eee = pl->mac_supports_eee_ops && + pl->config->lpi_capabilities && + !phy_interface_empty(pl->config->lpi_interfaces); + + /* Set the default EEE configuration */ + pl->eee_cfg.eee_enabled = pl->config->eee_enabled_default; + pl->eee_cfg.tx_lpi_enabled = pl->eee_cfg.eee_enabled; + pl->eee_cfg.tx_lpi_timer = pl->config->lpi_timer_default; + pl->phy_state.interface = iface; pl->link_interface = iface; if (iface == PHY_INTERFACE_MODE_MOCA) @@ -2012,16 +2072,22 @@ static void phylink_phy_change(struct phy_device *phydev, bool up) pl->phy_state.link = up; if (!up) pl->link_failed = true; + + /* Get the LPI state from phylib */ + pl->phy_enable_tx_lpi = phydev->enable_tx_lpi; + pl->mac_tx_lpi_timer = phydev->eee_cfg.tx_lpi_timer; mutex_unlock(&pl->state_mutex); phylink_run_resolve(pl); - phylink_dbg(pl, "phy link %s %s/%s/%s/%s/%s\n", up ? "up" : "down", + phylink_dbg(pl, "phy link %s %s/%s/%s/%s/%s/%slpi\n", + up ? "up" : "down", phy_modes(phydev->interface), phy_speed_to_str(phydev->speed), phy_duplex_to_str(phydev->duplex), phy_rate_matching_to_str(phydev->rate_matching), - phylink_pause_to_str(pl->phy_state.pause)); + phylink_pause_to_str(pl->phy_state.pause), + phydev->enable_tx_lpi ? "" : "no"); } static int phylink_validate_phy(struct phylink *pl, struct phy_device *phy, @@ -2151,6 +2217,36 @@ static int phylink_bringup_phy(struct phylink *pl, struct phy_device *phy, /* Restrict the phy advertisement according to the MAC support. */ linkmode_copy(phy->advertising, config.advertising); + + /* If the MAC supports phylink managed EEE, restrict the EEE + * advertisement according to the MAC's LPI capabilities. + */ + if (pl->mac_supports_eee) { + /* If EEE is enabled, then we need to call phy_support_eee() + * to ensure that the advertising mask is appropriately set. + * This also enables EEE at the PHY. + */ + if (pl->eee_cfg.eee_enabled) + phy_support_eee(phy); + + phy->eee_cfg.tx_lpi_enabled = pl->eee_cfg.tx_lpi_enabled; + phy->eee_cfg.tx_lpi_timer = pl->eee_cfg.tx_lpi_timer; + + /* Convert the MAC's LPI capabilities to linkmodes */ + linkmode_zero(pl->supported_lpi); + phylink_caps_to_linkmodes(pl->supported_lpi, + pl->config->lpi_capabilities); + + /* Restrict the PHYs EEE support/advertisement to the modes + * that the MAC supports. + */ + linkmode_and(phy->advertising_eee, phy->advertising_eee, + pl->supported_lpi); + } else if (pl->mac_supports_eee_ops) { + /* MAC supports phylink EEE, but wants EEE always disabled. */ + phy_disable_eee(phy); + } + mutex_unlock(&pl->state_mutex); mutex_unlock(&phy->lock); @@ -2166,7 +2262,13 @@ static int phylink_bringup_phy(struct phylink *pl, struct phy_device *phy, if (pl->config->mac_managed_pm) phy->mac_managed_pm = true; - return 0; + /* Allow the MAC to stop its clock if the PHY has the capability */ + pl->mac_tx_clk_stop = phy_eee_tx_clock_stop_capable(phy) > 0; + + /* Explicitly configure whether the PHY is allowed to stop it's + * receive clock. + */ + return phy_eee_rx_clock_stop(phy, pl->config->eee_rx_clk_stop_enable); } static int phylink_attach_phy(struct phylink *pl, struct phy_device *phy, @@ -2323,6 +2425,8 @@ void phylink_disconnect_phy(struct phylink *pl) mutex_lock(&phy->lock); mutex_lock(&pl->state_mutex); pl->phydev = NULL; + pl->phy_enable_tx_lpi = false; + pl->mac_tx_clk_stop = false; mutex_unlock(&pl->state_mutex); mutex_unlock(&phy->lock); flush_work(&pl->resolve); @@ -3077,8 +3181,16 @@ int phylink_ethtool_get_eee(struct phylink *pl, struct ethtool_keee *eee) ASSERT_RTNL(); - if (pl->phydev) + if (pl->mac_supports_eee_ops && !pl->mac_supports_eee) + return ret; + + if (pl->phydev) { ret = phy_ethtool_get_eee(pl->phydev, eee); + /* Restrict supported linkmode mask */ + if (ret == 0 && pl->mac_supports_eee_ops) + linkmode_and(eee->supported, eee->supported, + pl->supported_lpi); + } return ret; } @@ -3091,12 +3203,29 @@ EXPORT_SYMBOL_GPL(phylink_ethtool_get_eee); */ int phylink_ethtool_set_eee(struct phylink *pl, struct ethtool_keee *eee) { + bool mac_eee = pl->mac_supports_eee; int ret = -EOPNOTSUPP; ASSERT_RTNL(); - if (pl->phydev) + phylink_dbg(pl, "mac %s phylink EEE%s, adv %*pbl, LPI%s timer %uus\n", + mac_eee ? "supports" : "does not support", + eee->eee_enabled ? ", enabled" : "", + __ETHTOOL_LINK_MODE_MASK_NBITS, eee->advertised, + eee->tx_lpi_enabled ? " enabled" : "", eee->tx_lpi_timer); + + if (pl->mac_supports_eee_ops && !mac_eee) + return ret; + + if (pl->phydev) { + /* Restrict advertisement mask */ + if (pl->mac_supports_eee_ops) + linkmode_and(eee->advertised, eee->advertised, + pl->supported_lpi); ret = phy_ethtool_set_eee(pl->phydev, eee); + if (ret == 0) + eee_to_eeecfg(&pl->eee_cfg, eee); + } return ret; } diff --git a/include/linux/phy.h b/include/linux/phy.h index afaae74d0949..244f747b3cd9 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -2146,6 +2146,7 @@ int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask); int phy_unregister_fixup_for_id(const char *bus_id); int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask); +int phy_eee_tx_clock_stop_capable(struct phy_device *phydev); int phy_eee_rx_clock_stop(struct phy_device *phydev, bool clk_stop_enable); int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable); int phy_get_eee_err(struct phy_device *phydev); diff --git a/include/linux/phylink.h b/include/linux/phylink.h index f19b7108c840..898b00451bbf 100644 --- a/include/linux/phylink.h +++ b/include/linux/phylink.h @@ -5,6 +5,8 @@ #include <linux/spinlock.h> #include <linux/workqueue.h> +#include <net/eee.h> + struct device_node; struct ethtool_cmd; struct fwnode_handle; @@ -143,11 +145,17 @@ enum phylink_op_type { * possible and avoid stopping it during suspend events. * @default_an_inband: if true, defaults to MLO_AN_INBAND rather than * MLO_AN_PHY. A fixed-link specification will override. + * @eee_rx_clk_stop_enable: if true, PHY can stop the receive clock during LPI * @get_fixed_state: callback to execute to determine the fixed link state, * if MAC link is at %MLO_AN_FIXED mode. * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx * are supported by the MAC/PCS. + * @lpi_interfaces: bitmap describing which PHY interface modes can support + * LPI signalling. * @mac_capabilities: MAC pause/speed/duplex capabilities. + * @lpi_capabilities: MAC speeds which can support LPI signalling + * @lpi_timer_default: Default EEE LPI timer setting. + * @eee_enabled_default: If set, EEE will be enabled by phylink at creation time */ struct phylink_config { struct device *dev; @@ -156,10 +164,15 @@ struct phylink_config { bool mac_managed_pm; bool mac_requires_rxc; bool default_an_inband; + bool eee_rx_clk_stop_enable; void (*get_fixed_state)(struct phylink_config *config, struct phylink_link_state *state); DECLARE_PHY_INTERFACE_MASK(supported_interfaces); + DECLARE_PHY_INTERFACE_MASK(lpi_interfaces); unsigned long mac_capabilities; + unsigned long lpi_capabilities; + u32 lpi_timer_default; + bool eee_enabled_default; }; void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed); @@ -173,6 +186,8 @@ void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed); * @mac_finish: finish a major reconfiguration of the interface. * @mac_link_down: take the link down. * @mac_link_up: allow the link to come up. + * @mac_disable_tx_lpi: disable LPI. + * @mac_enable_tx_lpi: enable and configure LPI. * * The individual methods are described more fully below. */ @@ -193,6 +208,9 @@ struct phylink_mac_ops { struct phy_device *phy, unsigned int mode, phy_interface_t interface, int speed, int duplex, bool tx_pause, bool rx_pause); + void (*mac_disable_tx_lpi)(struct phylink_config *config); + int (*mac_enable_tx_lpi)(struct phylink_config *config, u32 timer, + bool tx_clk_stop); }; #if 0 /* For kernel-doc purposes only. */ @@ -387,6 +405,33 @@ void mac_link_down(struct phylink_config *config, unsigned int mode, void mac_link_up(struct phylink_config *config, struct phy_device *phy, unsigned int mode, phy_interface_t interface, int speed, int duplex, bool tx_pause, bool rx_pause); + +/** + * mac_disable_tx_lpi() - disable LPI generation at the MAC + * @config: a pointer to a &struct phylink_config. + * + * Disable generation of LPI at the MAC, effectively preventing the MAC + * from indicating that it is idle. + */ +void mac_disable_tx_lpi(struct phylink_config *config); + +/** + * mac_enable_tx_lpi() - configure and enable LPI generation at the MAC + * @config: a pointer to a &struct phylink_config. + * @timer: LPI timeout in microseconds. + * @tx_clk_stop: allow xMII transmit clock to be stopped during LPI + * + * Configure the LPI timeout accordingly. This will only be called when + * the link is already up, to cater for situations where the hardware + * needs to be programmed according to the link speed. + * + * Enable LPI generation at the MAC, and configure whether the xMII transmit + * clock may be stopped. + * + * Returns: 0 on success. Please consult with rmk before returning an error. + */ +int mac_enable_tx_lpi(struct phylink_config *config, u32 timer, + bool tx_clk_stop); #endif struct phylink_pcs_ops; diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h index f0d3f268240d..6975f182b22c 100644 --- a/include/uapi/linux/mdio.h +++ b/include/uapi/linux/mdio.h @@ -125,6 +125,7 @@ #define MDIO_STAT1_LPOWERABLE 0x0002 /* Low-power ability */ #define MDIO_STAT1_LSTATUS BMSR_LSTATUS #define MDIO_STAT1_FAULT 0x0080 /* Fault */ +#define MDIO_PCS_STAT1_CLKSTOP_CAP 0x0040 #define MDIO_AN_STAT1_LPABLE 0x0001 /* Link partner AN ability */ #define MDIO_AN_STAT1_ABLE BMSR_ANEGCAPABLE #define MDIO_AN_STAT1_RFAULT BMSR_RFAULT |