diff options
Diffstat (limited to 'Documentation/admin-guide/pm/cpuidle.rst')
| -rw-r--r-- | Documentation/admin-guide/pm/cpuidle.rst | 107 |
1 files changed, 23 insertions, 84 deletions
diff --git a/Documentation/admin-guide/pm/cpuidle.rst b/Documentation/admin-guide/pm/cpuidle.rst index a96a423e3779..19754beb5a4e 100644 --- a/Documentation/admin-guide/pm/cpuidle.rst +++ b/Documentation/admin-guide/pm/cpuidle.rst @@ -347,81 +347,8 @@ for tickless systems. It follows the same basic strategy as the ``menu`` `one <menu-gov_>`_: it always tries to find the deepest idle state suitable for the given conditions. However, it applies a different approach to that problem. -First, it does not use sleep length correction factors, but instead it attempts -to correlate the observed idle duration values with the available idle states -and use that information to pick up the idle state that is most likely to -"match" the upcoming CPU idle interval. Second, it does not take the tasks -that were running on the given CPU in the past and are waiting on some I/O -operations to complete now at all (there is no guarantee that they will run on -the same CPU when they become runnable again) and the pattern detection code in -it avoids taking timer wakeups into account. It also only uses idle duration -values less than the current time till the closest timer (with the scheduler -tick excluded) for that purpose. - -Like in the ``menu`` governor `case <menu-gov_>`_, the first step is to obtain -the *sleep length*, which is the time until the closest timer event with the -assumption that the scheduler tick will be stopped (that also is the upper bound -on the time until the next CPU wakeup). That value is then used to preselect an -idle state on the basis of three metrics maintained for each idle state provided -by the ``CPUIdle`` driver: ``hits``, ``misses`` and ``early_hits``. - -The ``hits`` and ``misses`` metrics measure the likelihood that a given idle -state will "match" the observed (post-wakeup) idle duration if it "matches" the -sleep length. They both are subject to decay (after a CPU wakeup) every time -the target residency of the idle state corresponding to them is less than or -equal to the sleep length and the target residency of the next idle state is -greater than the sleep length (that is, when the idle state corresponding to -them "matches" the sleep length). The ``hits`` metric is increased if the -former condition is satisfied and the target residency of the given idle state -is less than or equal to the observed idle duration and the target residency of -the next idle state is greater than the observed idle duration at the same time -(that is, it is increased when the given idle state "matches" both the sleep -length and the observed idle duration). In turn, the ``misses`` metric is -increased when the given idle state "matches" the sleep length only and the -observed idle duration is too short for its target residency. - -The ``early_hits`` metric measures the likelihood that a given idle state will -"match" the observed (post-wakeup) idle duration if it does not "match" the -sleep length. It is subject to decay on every CPU wakeup and it is increased -when the idle state corresponding to it "matches" the observed (post-wakeup) -idle duration and the target residency of the next idle state is less than or -equal to the sleep length (i.e. the idle state "matching" the sleep length is -deeper than the given one). - -The governor walks the list of idle states provided by the ``CPUIdle`` driver -and finds the last (deepest) one with the target residency less than or equal -to the sleep length. Then, the ``hits`` and ``misses`` metrics of that idle -state are compared with each other and it is preselected if the ``hits`` one is -greater (which means that that idle state is likely to "match" the observed idle -duration after CPU wakeup). If the ``misses`` one is greater, the governor -preselects the shallower idle state with the maximum ``early_hits`` metric -(or if there are multiple shallower idle states with equal ``early_hits`` -metric which also is the maximum, the shallowest of them will be preselected). -[If there is a wakeup latency constraint coming from the `PM QoS framework -<cpu-pm-qos_>`_ which is hit before reaching the deepest idle state with the -target residency within the sleep length, the deepest idle state with the exit -latency within the constraint is preselected without consulting the ``hits``, -``misses`` and ``early_hits`` metrics.] - -Next, the governor takes several idle duration values observed most recently -into consideration and if at least a half of them are greater than or equal to -the target residency of the preselected idle state, that idle state becomes the -final candidate to ask for. Otherwise, the average of the most recent idle -duration values below the target residency of the preselected idle state is -computed and the governor walks the idle states shallower than the preselected -one and finds the deepest of them with the target residency within that average. -That idle state is then taken as the final candidate to ask for. - -Still, at this point the governor may need to refine the idle state selection if -it has not decided to `stop the scheduler tick <idle-cpus-and-tick_>`_. That -generally happens if the target residency of the idle state selected so far is -less than the tick period and the tick has not been stopped already (in a -previous iteration of the idle loop). Then, like in the ``menu`` governor -`case <menu-gov_>`_, the sleep length used in the previous computations may not -reflect the real time until the closest timer event and if it really is greater -than that time, a shallower state with a suitable target residency may need to -be selected. - +.. kernel-doc:: drivers/cpuidle/governors/teo.c + :doc: teo-description .. _idle-states-representation: @@ -478,7 +405,7 @@ order to ask the hardware to enter that state. Also, for each statistics of the given idle state. That information is exposed by the kernel via ``sysfs``. -For each CPU in the system, there is a :file:`/sys/devices/system/cpu<N>/cpuidle/` +For each CPU in the system, there is a :file:`/sys/devices/system/cpu/cpu<N>/cpuidle/` directory in ``sysfs``, where the number ``<N>`` is assigned to the given CPU at the initialization time. That directory contains a set of subdirectories called :file:`state0`, :file:`state1` and so on, up to the number of idle state @@ -494,7 +421,7 @@ object corresponding to it, as follows: residency. ``below`` - Total number of times this idle state had been asked for, but cerainly + Total number of times this idle state had been asked for, but certainly a deeper idle state would have been a better match for the observed idle duration. @@ -528,6 +455,10 @@ object corresponding to it, as follows: Total number of times the hardware has been asked by the given CPU to enter this idle state. +``rejected`` + Total number of times a request to enter this idle state on the given + CPU was rejected. + The :file:`desc` and :file:`name` files both contain strings. The difference between them is that the name is expected to be more concise, while the description may be longer and it may contain white space or special characters. @@ -572,6 +503,11 @@ particular case. For these reasons, the only reliable way to find out how much time has been spent by the hardware in different idle states supported by it is to use idle state residency counters in the hardware, if available. +Generally, an interrupt received when trying to enter an idle state causes the +idle state entry request to be rejected, in which case the ``CPUIdle`` driver +may return an error code to indicate that this was the case. The :file:`usage` +and :file:`rejected` files report the number of times the given idle state +was entered successfully or rejected, respectively. .. _cpu-pm-qos: @@ -676,8 +612,8 @@ the ``menu`` governor to be used on the systems that use the ``ladder`` governor by default this way, for example. The other kernel command line parameters controlling CPU idle time management -described below are only relevant for the *x86* architecture and some of -them affect Intel processors only. +described below are only relevant for the *x86* architecture and references +to ``intel_idle`` affect Intel processors only. The *x86* architecture support code recognizes three kernel command line options related to CPU idle time management: ``idle=poll``, ``idle=halt``, @@ -690,7 +626,7 @@ which of the two parameters is added to the kernel command line. In the instruction of the CPUs (which, as a rule, suspends the execution of the program and causes the hardware to attempt to enter the shallowest available idle state) for this purpose, and if ``idle=poll`` is used, idle CPUs will execute a -more or less ``lightweight'' sequence of instructions in a tight loop. [Note +more or less "lightweight" sequence of instructions in a tight loop. [Note that using ``idle=poll`` is somewhat drastic in many cases, as preventing idle CPUs from saving almost any energy at all may not be the only effect of it. For example, on Intel hardware it effectively prevents CPUs from using @@ -699,10 +635,13 @@ idle, so it very well may hurt single-thread computations performance as well as energy-efficiency. Thus using it for performance reasons may not be a good idea at all.] -The ``idle=nomwait`` option disables the ``intel_idle`` driver and causes -``acpi_idle`` to be used (as long as all of the information needed by it is -there in the system's ACPI tables), but it is not allowed to use the -``MWAIT`` instruction of the CPUs to ask the hardware to enter idle states. +The ``idle=nomwait`` option prevents the use of ``MWAIT`` instruction of +the CPU to enter idle states. When this option is used, the ``acpi_idle`` +driver will use the ``HLT`` instruction instead of ``MWAIT``. On systems +running Intel processors, this option disables the ``intel_idle`` driver +and forces the use of the ``acpi_idle`` driver instead. Note that in either +case, ``acpi_idle`` driver will function only if all the information needed +by it is in the system's ACPI tables. In addition to the architecture-level kernel command line options affecting CPU idle time management, there are parameters affecting individual ``CPUIdle`` |