diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/msm/dsi.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/dsi.txt | 246 |
1 files changed, 0 insertions, 246 deletions
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt deleted file mode 100644 index af95586c898f..000000000000 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ /dev/null @@ -1,246 +0,0 @@ -Qualcomm Technologies Inc. adreno/snapdragon DSI output - -DSI Controller: -Required properties: -- compatible: - * "qcom,mdss-dsi-ctrl" -- reg: Physical base address and length of the registers of controller -- reg-names: The names of register regions. The following regions are required: - * "dsi_ctrl" -- interrupts: The interrupt signal from the DSI block. -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. -- clock-names: the following clocks are required: - * "mdp_core" - * "iface" - * "bus" - * "core_mmss" - * "byte" - * "pixel" - * "core" - For DSIv2, we need an additional clock: - * "src" - For DSI6G v2.0 onwards, we need also need the clock: - * "byte_intf" -- assigned-clocks: Parents of "byte" and "pixel" for the given platform. -- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided - by a DSI PHY block. See [1] for details on clock bindings. -- vdd-supply: phandle to vdd regulator device node -- vddio-supply: phandle to vdd-io regulator device node -- vdda-supply: phandle to vdda regulator device node -- phys: phandle to DSI PHY device node -- phy-names: the name of the corresponding PHY device -- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) -- ports: Contains 2 DSI controller ports as child nodes. Each port contains - an endpoint subnode as defined in [2] and [3]. - -Optional properties: -- panel@0: Node of panel connected to this DSI controller. - See files in [4] for each supported panel. -- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is - driving a panel which needs 2 DSI links. -- qcom,master-dsi: Boolean value indicating if the DSI controller is driving - the master link of the 2-DSI panel. -- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is - driving a 2-DSI panel whose 2 links need receive command simultaneously. -- pinctrl-names: the pin control state names; should contain "default" -- pinctrl-0: the default pinctrl state (active) -- pinctrl-n: the "sleep" pinctrl state -- ports: contains DSI controller input and output ports as children, each - containing one endpoint subnode. - - DSI Endpoint properties: - - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's - input endpoint. For port@1, set to the MDP interface output. See [2] for - device graph info. - - - data-lanes: this describes how the physical DSI data lanes are mapped - to the logical lanes on the given platform. The value contained in - index n describes what physical lane is mapped to the logical lane n - (DATAn, where n lies between 0 and 3). The clock lane position is fixed - and can't be changed. Hence, they aren't a part of the DT bindings. See - [3] for more info on the data-lanes property. - - For example: - - data-lanes = <3 0 1 2>; - - The above mapping describes that the logical data lane DATA0 is mapped to - the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 - to phys DATA1 and logic DATA3 to phys DATA2. - - There are only a limited number of physical to logical mappings possible: - <0 1 2 3> - <1 2 3 0> - <2 3 0 1> - <3 0 1 2> - <0 3 2 1> - <1 0 3 2> - <2 1 0 3> - <3 2 1 0> - -DSI PHY: -Required properties: -- compatible: Could be the following - * "qcom,dsi-phy-28nm-hpm" - * "qcom,dsi-phy-28nm-lp" - * "qcom,dsi-phy-20nm" - * "qcom,dsi-phy-28nm-8960" - * "qcom,dsi-phy-14nm" - * "qcom,dsi-phy-10nm" - * "qcom,dsi-phy-10nm-8998" -- reg: Physical base address and length of the registers of PLL, PHY. Some - revisions require the PHY regulator base address, whereas others require the - PHY lane base address. See below for each PHY revision. -- reg-names: The names of register regions. The following regions are required: - For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_regulator" - For DSI 14nm and 10nm PHYs: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_lane" -- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating - 2 clocks: A byte clock (index 0), and a pixel clock (index 1). -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. See [1] for details on clock bindings. -- clock-names: the following clocks are required: - * "iface" - * "ref" (only required for new DTS files/entries) - For 28nm HPM/LP, 28nm 8960 PHYs: -- vddio-supply: phandle to vdd-io regulator device node - For 20nm PHY: -- vddio-supply: phandle to vdd-io regulator device node -- vcca-supply: phandle to vcca regulator device node - For 14nm PHY: -- vcca-supply: phandle to vcca regulator device node - For 10nm PHY: -- vdds-supply: phandle to vdds regulator device node - -Optional properties: -- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY - regulator is wanted. -- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode - panels in microseconds. Driver uses this number to adjust - the clock rate according to the expected transfer time. - Increasing this value would slow down the mdp processing - and can result in slower performance. - Decreasing this value can speed up the mdp processing, - but this can also impact power consumption. - As a rule this time should not be higher than the time - that would be expected with the processing at the - dsi link rate since anyways this would be the maximum - transfer time that could be achieved. - If ping pong split is enabled, this time should not be higher - than two times the dsi link rate time. - If the property is not specified, then the default value is 14000 us. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/graph.txt -[3] Documentation/devicetree/bindings/media/video-interfaces.txt -[4] Documentation/devicetree/bindings/display/panel/ - -Example: - dsi0: dsi@fd922800 { - compatible = "qcom,mdss-dsi-ctrl"; - qcom,dsi-host-index = <0>; - interrupt-parent = <&mdp>; - interrupts = <4 0>; - reg-names = "dsi_ctrl"; - reg = <0xfd922800 0x200>; - power-domains = <&mmcc MDSS_GDSC>; - clock-names = - "bus", - "byte", - "core", - "core_mmss", - "iface", - "mdp_core", - "pixel"; - clocks = - <&mmcc MDSS_AXI_CLK>, - <&mmcc MDSS_BYTE0_CLK>, - <&mmcc MDSS_ESC0_CLK>, - <&mmcc MMSS_MISC_AHB_CLK>, - <&mmcc MDSS_AHB_CLK>, - <&mmcc MDSS_MDP_CLK>, - <&mmcc MDSS_PCLK0_CLK>; - - assigned-clocks = - <&mmcc BYTE0_CLK_SRC>, - <&mmcc PCLK0_CLK_SRC>; - assigned-clock-parents = - <&dsi_phy0 0>, - <&dsi_phy0 1>; - - vdda-supply = <&pma8084_l2>; - vdd-supply = <&pma8084_l22>; - vddio-supply = <&pma8084_l12>; - - phys = <&dsi_phy0>; - phy-names ="dsi-phy"; - - qcom,dual-dsi-mode; - qcom,master-dsi; - qcom,sync-dual-dsi; - - qcom,mdss-mdp-transfer-time-us = <12000>; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&dsi_active>; - pinctrl-1 = <&dsi_suspend>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dsi0_in: endpoint { - remote-endpoint = <&mdp_intf1_out>; - }; - }; - - port@1 { - reg = <1>; - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - data-lanes = <0 1 2 3>; - }; - }; - }; - - panel: panel@0 { - compatible = "sharp,lq101r1sx01"; - reg = <0>; - link2 = <&secondary>; - - power-supply = <...>; - backlight = <...>; - - port { - panel_in: endpoint { - remote-endpoint = <&dsi0_out>; - }; - }; - }; - }; - - dsi_phy0: dsi-phy@fd922a00 { - compatible = "qcom,dsi-phy-28nm-hpm"; - qcom,dsi-phy-index = <0>; - reg-names = - "dsi_pll", - "dsi_phy", - "dsi_phy_regulator"; - reg = <0xfd922a00 0xd4>, - <0xfd922b00 0x2b0>, - <0xfd922d80 0x7b>; - clock-names = "iface"; - clocks = <&mmcc MDSS_AHB_CLK>; - #clock-cells = <1>; - vddio-supply = <&pma8084_l12>; - - qcom,dsi-phy-regulator-ldo-mode; - }; |