diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display')
107 files changed, 3170 insertions, 1594 deletions
diff --git a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-display-engine.yaml b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-display-engine.yaml index 944ff2f1cf93..e77523b02fad 100644 --- a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-display-engine.yaml +++ b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-display-engine.yaml @@ -66,10 +66,9 @@ properties: - allwinner,sun50i-h6-display-engine allwinner,pipelines: - allOf: - - $ref: /schemas/types.yaml#/definitions/phandle-array - - minItems: 1 - maxItems: 2 + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + maxItems: 2 description: | Available display engine frontends (DE 1.0) or mixers (DE 2.0/3.0) available. diff --git a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-hdmi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-hdmi.yaml index 5d4915aed1e2..75e6479397a5 100644 --- a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-hdmi.yaml +++ b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-hdmi.yaml @@ -21,8 +21,8 @@ properties: - const: allwinner,sun5i-a10s-hdmi - const: allwinner,sun6i-a31-hdmi - items: - - const: allwinner,sun7i-a20-hdmi - - const: allwinner,sun5i-a10s-hdmi + - const: allwinner,sun7i-a20-hdmi + - const: allwinner,sun5i-a10s-hdmi reg: maxItems: 1 @@ -33,32 +33,32 @@ properties: clocks: oneOf: - items: - - description: The HDMI interface clock - - description: The HDMI module clock - - description: The first video PLL - - description: The second video PLL + - description: The HDMI interface clock + - description: The HDMI module clock + - description: The first video PLL + - description: The second video PLL - items: - - description: The HDMI interface clock - - description: The HDMI module clock - - description: The HDMI DDC clock - - description: The first video PLL - - description: The second video PLL + - description: The HDMI interface clock + - description: The HDMI module clock + - description: The HDMI DDC clock + - description: The first video PLL + - description: The second video PLL clock-names: oneOf: - items: - - const: ahb - - const: mod - - const: pll-0 - - const: pll-1 + - const: ahb + - const: mod + - const: pll-0 + - const: pll-1 - items: - - const: ahb - - const: mod - - const: ddc - - const: pll-0 - - const: pll-1 + - const: ahb + - const: mod + - const: ddc + - const: pll-0 + - const: pll-1 resets: maxItems: 1 diff --git a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-tcon.yaml b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-tcon.yaml index e5344c4ae226..4c15a2644a7c 100644 --- a/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-tcon.yaml +++ b/Documentation/devicetree/bindings/display/allwinner,sun4i-a10-tcon.yaml @@ -35,26 +35,26 @@ properties: - const: allwinner,sun9i-a80-tcon-tv - items: - - enum: - - allwinner,sun7i-a20-tcon0 - - allwinner,sun7i-a20-tcon1 - - const: allwinner,sun7i-a20-tcon + - enum: + - allwinner,sun7i-a20-tcon0 + - allwinner,sun7i-a20-tcon1 + - const: allwinner,sun7i-a20-tcon - items: - - enum: - - allwinner,sun50i-a64-tcon-lcd - - const: allwinner,sun8i-a83t-tcon-lcd + - enum: + - allwinner,sun50i-a64-tcon-lcd + - const: allwinner,sun8i-a83t-tcon-lcd - items: - - enum: - - allwinner,sun8i-h3-tcon-tv - - allwinner,sun50i-a64-tcon-tv - - const: allwinner,sun8i-a83t-tcon-tv + - enum: + - allwinner,sun8i-h3-tcon-tv + - allwinner,sun50i-a64-tcon-tv + - const: allwinner,sun8i-a83t-tcon-tv - items: - - enum: - - allwinner,sun50i-h6-tcon-tv - - const: allwinner,sun8i-r40-tcon-tv + - enum: + - allwinner,sun50i-h6-tcon-tv + - const: allwinner,sun8i-r40-tcon-tv reg: maxItems: 1 @@ -71,11 +71,10 @@ properties: maxItems: 4 clock-output-names: - allOf: - - $ref: /schemas/types.yaml#/definitions/string-array - - maxItems: 1 description: Name of the LCD pixel clock created. + $ref: /schemas/types.yaml#/definitions/string-array + maxItems: 1 dmas: maxItems: 1 @@ -83,37 +82,37 @@ properties: resets: anyOf: - items: - - description: TCON Reset Line + - description: TCON Reset Line - items: - - description: TCON Reset Line - - description: TCON LVDS Reset Line + - description: TCON Reset Line + - description: TCON LVDS Reset Line - items: - - description: TCON Reset Line - - description: TCON eDP Reset Line + - description: TCON Reset Line + - description: TCON eDP Reset Line - items: - - description: TCON Reset Line - - description: TCON eDP Reset Line - - description: TCON LVDS Reset Line + - description: TCON Reset Line + - description: TCON eDP Reset Line + - description: TCON LVDS Reset Line reset-names: oneOf: - const: lcd - items: - - const: lcd - - const: lvds + - const: lcd + - const: lvds - items: - - const: lcd - - const: edp + - const: lcd + - const: edp - items: - - const: lcd - - const: edp - - const: lvds + - const: lcd + - const: edp + - const: lvds ports: type: object diff --git a/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml index 9e90c2b00960..63f948175239 100644 --- a/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml +++ b/Documentation/devicetree/bindings/display/allwinner,sun6i-a31-mipi-dsi.yaml @@ -76,28 +76,28 @@ required: allOf: - if: properties: - compatible: - contains: - const: allwinner,sun6i-a31-mipi-dsi + compatible: + contains: + const: allwinner,sun6i-a31-mipi-dsi then: - properties: - clocks: - minItems: 2 + properties: + clocks: + minItems: 2 - required: - - clock-names + required: + - clock-names - if: properties: - compatible: - contains: - const: allwinner,sun50i-a64-mipi-dsi + compatible: + contains: + const: allwinner,sun50i-a64-mipi-dsi then: - properties: - clocks: - minItems: 1 + properties: + clocks: + minItems: 1 additionalProperties: false @@ -119,7 +119,7 @@ examples: panel@0 { compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; reg = <0>; - power-gpios = <&pio 1 7 0>; /* PB07 */ + power-supply = <®_display>; reset-gpios = <&r_pio 0 5 1>; /* PL05 */ backlight = <&pwm_bl>; }; diff --git a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml index 4d6795690ac3..fa4769a0b26e 100644 --- a/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml +++ b/Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml @@ -29,11 +29,11 @@ properties: - const: allwinner,sun50i-h6-dw-hdmi - items: - - enum: - - allwinner,sun8i-h3-dw-hdmi - - allwinner,sun8i-r40-dw-hdmi - - allwinner,sun50i-a64-dw-hdmi - - const: allwinner,sun8i-a83t-dw-hdmi + - enum: + - allwinner,sun8i-h3-dw-hdmi + - allwinner,sun8i-r40-dw-hdmi + - allwinner,sun50i-a64-dw-hdmi + - const: allwinner,sun8i-a83t-dw-hdmi reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt deleted file mode 100644 index a6b2b2b8f3d9..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt +++ /dev/null @@ -1,50 +0,0 @@ -Analog Device ADV7123 Video DAC -------------------------------- - -The ADV7123 is a digital-to-analog converter that outputs VGA signals from a -parallel video input. - -Required properties: - -- compatible: Should be "adi,adv7123" - -Optional properties: - -- psave-gpios: Power save control GPIO - -Required nodes: - -The ADV7123 has two video ports. Their connections are modeled using the OF -graph bindings specified in Documentation/devicetree/bindings/graph.txt. - -- Video port 0 for DPI input -- Video port 1 for VGA output - - -Example -------- - - adv7123: encoder@0 { - compatible = "adi,adv7123"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - adv7123_in: endpoint@0 { - remote-endpoint = <&dpi_out>; - }; - }; - - port@1 { - reg = <1>; - - adv7123_out: endpoint@0 { - remote-endpoint = <&vga_connector_in>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index e8ddec5d9d91..659523f538bf 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -1,5 +1,5 @@ -Analog Device ADV7511(W)/13/33/35 HDMI Encoders ------------------------------------------ +Analog Devices ADV7511(W)/13/33/35 HDMI Encoders +------------------------------------------------ The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7814.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7814.yaml new file mode 100644 index 000000000000..3ba477aefdd7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7814.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/analogix,anx7814.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analogix ANX7814 SlimPort (Full-HD Transmitter) + +maintainers: + - Enric Balletbo i Serra <enric.balletbo@collabora.com> + +properties: + compatible: + enum: + - analogix,anx7808 + - analogix,anx7812 + - analogix,anx7814 + - analogix,anx7818 + + reg: + maxItems: 1 + description: I2C address of the device. + + interrupts: + maxItems: 1 + description: Should contain the INTP interrupt. + + hpd-gpios: + deprecated: true + maxItems: 1 + description: Which GPIO to use for hpd. + + pd-gpios: + maxItems: 1 + description: Which GPIO to use for power down. + + reset-gpios: + maxItems: 1 + description: Which GPIO to use for reset. + + dvdd10-supply: + description: Regulator for 1.0V digital core power. + + ports: + type: object + description: + A node containing input and output port nodes with endpoint + definitions as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + Documentation/devicetree/bindings/graph.txt + + properties: + port@0: + type: object + description: Video port for HDMI input. + + properties: + reg: + const: 0 + + port@1: + type: object + description: + Video port for SlimPort, DisplayPort, eDP or MyDP output. + + properties: + reg: + const: 1 + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + anx7814: bridge@38 { + compatible = "analogix,anx7814"; + reg = <0x38>; + interrupt-parent = <&gpio0>; + interrupts = <99 IRQ_TYPE_LEVEL_LOW>; /* INTP */ + pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + anx7814_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + + port@1 { + reg = <1>; + anx7814_out: endpoint { + remote-endpoint = <&edp_out>; + }; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/bridge/anx6345.yaml b/Documentation/devicetree/bindings/display/bridge/anx6345.yaml index c21103869923..8c0e4f285fbc 100644 --- a/Documentation/devicetree/bindings/display/bridge/anx6345.yaml +++ b/Documentation/devicetree/bindings/display/bridge/anx6345.yaml @@ -37,6 +37,12 @@ properties: type: object properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + port@0: type: object description: | @@ -51,6 +57,8 @@ properties: required: - port@0 + additionalProperties: false + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/bridge/anx7814.txt b/Documentation/devicetree/bindings/display/bridge/anx7814.txt deleted file mode 100644 index 17258747fff6..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/anx7814.txt +++ /dev/null @@ -1,42 +0,0 @@ -Analogix ANX7814 SlimPort (Full-HD Transmitter) ------------------------------------------------ - -The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter -designed for portable devices. - -Required properties: - - - compatible : Must be one of: - "analogix,anx7808" - "analogix,anx7812" - "analogix,anx7814" - "analogix,anx7818" - - reg : I2C address of the device - - interrupts : Should contain the INTP interrupt - - hpd-gpios : Which GPIO to use for hpd - - pd-gpios : Which GPIO to use for power down - - reset-gpios : Which GPIO to use for reset - -Optional properties: - - - dvdd10-supply : Regulator for 1.0V digital core power. - - Video port for HDMI input, using the DT bindings defined in [1]. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - - anx7814: anx7814@38 { - compatible = "analogix,anx7814"; - reg = <0x38>; - interrupt-parent = <&gpio0>; - interrupts = <99 IRQ_TYPE_LEVEL_LOW>; /* INTP */ - hpd-gpios = <&pio 36 GPIO_ACTIVE_HIGH>; - pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; - reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>; - port { - anx7814_in: endpoint { - remote-endpoint = <&hdmi0_out>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml new file mode 100644 index 000000000000..9f38f55fc990 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/chrontel,ch7033.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019,2020 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/chrontel,ch7033.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Chrontel CH7033 Video Encoder Device Tree Bindings + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + compatible: + const: chrontel,ch7033 + + reg: + maxItems: 1 + description: I2C address of the device + + ports: + type: object + + properties: + port@0: + type: object + description: | + Video port for RGB input. + + port@1: + type: object + description: | + DVI port, should be connected to a node compatible with the + dvi-connector binding. + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - ports + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + vga-dvi-encoder@76 { + compatible = "chrontel,ch7033"; + reg = <0x76>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&lcd0_rgb_out>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&dvi_in>; + }; + }; + + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt b/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt deleted file mode 100644 index 164cbb15f04c..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/dumb-vga-dac.txt +++ /dev/null @@ -1,50 +0,0 @@ -Dumb RGB to VGA DAC bridge ---------------------------- - -This binding is aimed for dumb RGB to VGA DAC based bridges that do not require -any configuration. - -Required properties: - -- compatible: Must be "dumb-vga-dac" - -Required nodes: - -This device has two video ports. Their connections are modelled using the OF -graph bindings specified in Documentation/devicetree/bindings/graph.txt. - -- Video port 0 for RGB input -- Video port 1 for VGA output - -Optional properties: -- vdd-supply: Power supply for DAC - -Example -------- - -bridge { - compatible = "dumb-vga-dac"; - #address-cells = <1>; - #size-cells = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - vga_bridge_in: endpoint { - remote-endpoint = <&tcon0_out_vga>; - }; - }; - - port@1 { - reg = <1>; - - vga_bridge_out: endpoint { - remote-endpoint = <&vga_con_in>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt b/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt deleted file mode 100644 index b13adf30b8d3..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt +++ /dev/null @@ -1,32 +0,0 @@ -Synopsys DesignWare MIPI DSI host controller -============================================ - -This document defines device tree properties for the Synopsys DesignWare MIPI -DSI host controller. It doesn't constitue a device tree binding specification -by itself but is meant to be referenced by platform-specific device tree -bindings. - -When referenced from platform device tree bindings the properties defined in -this document are defined as follows. The platform device tree bindings are -responsible for defining whether each optional property is used or not. - -- reg: Memory mapped base address and length of the DesignWare MIPI DSI - host controller registers. (mandatory) - -- clocks: References to all the clocks specified in the clock-names property - as specified in [1]. (mandatory) - -- clock-names: - - "pclk" is the peripheral clock for either AHB and APB. (mandatory) - - "px_clk" is the pixel clock for the DPI/RGB input. (optional) - -- resets: References to all the resets specified in the reset-names property - as specified in [2]. (optional) - -- reset-names: string reset name, must be "apb" if used. (optional) - -- panel or bridge node: see [3]. (mandatory) - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/reset/reset.txt -[3] Documentation/devicetree/bindings/display/mipi-dsi-bus.txt diff --git a/Documentation/devicetree/bindings/display/bridge/ite,it6505.yaml b/Documentation/devicetree/bindings/display/bridge/ite,it6505.yaml new file mode 100644 index 000000000000..2c500166c65d --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ite,it6505.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/ite,it6505.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ITE it6505 Device Tree Bindings + +maintainers: + - Allen Chen <allen.chen@ite.com.tw> + +description: | + The IT6505 is a high-performance DisplayPort 1.1a transmitter, + fully compliant with DisplayPort 1.1a, HDCP 1.3 specifications. + The IT6505 supports color depth of up to 36 bits (12 bits/color) + and ensures robust transmission of high-quality uncompressed video + content, along with uncompressed and compressed digital audio content. + + Aside from the various video output formats supported, the IT6505 + also encodes and transmits up to 8 channels of I2S digital audio, + with sampling rate up to 192kHz and sample size up to 24 bits. + In addition, an S/PDIF input port takes in compressed audio of up to + 192kHz frame rate. + + Each IT6505 chip comes preprogrammed with an unique HDCP key, + in compliance with the HDCP 1.3 standard so as to provide secure + transmission of high-definition content. Users of the IT6505 need not + purchase any HDCP keys or ROMs. + +properties: + compatible: + const: ite,it6505 + + ovdd-supply: + maxItems: 1 + description: I/O voltage + + pwr18-supply: + maxItems: 1 + description: core voltage + + interrupts: + maxItems: 1 + description: interrupt specifier of INT pin + + reset-gpios: + maxItems: 1 + description: gpio specifier of RESET pin + + extcon: + maxItems: 1 + description: extcon specifier for the Power Delivery + + port: + type: object + description: A port node pointing to DPI host port node + +required: + - compatible + - ovdd-supply + - pwr18-supply + - interrupts + - reset-gpios + - extcon + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + dp-bridge@5c { + compatible = "ite,it6505"; + interrupts = <152 IRQ_TYPE_EDGE_FALLING 152 0>; + reg = <0x5c>; + pinctrl-names = "default"; + pinctrl-0 = <&it6505_pins>; + ovdd-supply = <&mt6358_vsim1_reg>; + pwr18-supply = <&it6505_pp18_reg>; + reset-gpios = <&pio 179 1>; + extcon = <&usbc_extcon>; + + port { + it6505_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml index 8f373029f5d2..68951d56ebba 100644 --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml @@ -32,17 +32,17 @@ properties: compatible: oneOf: - items: - - enum: - - ti,ds90c185 # For the TI DS90C185 FPD-Link Serializer - - ti,ds90c187 # For the TI DS90C187 FPD-Link Serializer - - ti,sn75lvds83 # For the TI SN75LVDS83 FlatLink transmitter - - const: lvds-encoder # Generic LVDS encoder compatible fallback + - enum: + - ti,ds90c185 # For the TI DS90C185 FPD-Link Serializer + - ti,ds90c187 # For the TI DS90C187 FPD-Link Serializer + - ti,sn75lvds83 # For the TI SN75LVDS83 FlatLink transmitter + - const: lvds-encoder # Generic LVDS encoder compatible fallback - items: - - enum: - - ti,ds90cf384a # For the DS90CF384A FPD-Link LVDS Receiver - - const: lvds-decoder # Generic LVDS decoders compatible fallback + - enum: + - ti,ds90cf384a # For the DS90CF384A FPD-Link LVDS Receiver + - const: lvds-decoder # Generic LVDS decoders compatible fallback - enum: - - thine,thc63lvdm83d # For the THC63LVDM83D LVDS serializer + - thine,thc63lvdm83d # For the THC63LVDM83D LVDS serializer ports: type: object @@ -50,6 +50,12 @@ properties: This device has two video ports. Their connections are modeled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + port@0: type: object description: | @@ -66,6 +72,8 @@ properties: - port@0 - port@1 + additionalProperties: false + powerdown-gpios: description: The GPIO used to control the power down line of this device. diff --git a/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file mode 100644 index 000000000000..8aff2d68fc33 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml @@ -0,0 +1,226 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Northwest Logic MIPI-DSI controller on i.MX SoCs + +maintainers: + - Guido Gúnther <agx@sigxcpu.org> + - Robert Chiras <robert.chiras@nxp.com> + +description: | + NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for + the SOCs NWL MIPI-DSI host controller. + +properties: + compatible: + const: fsl,imx8mq-nwl-dsi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + clocks: + items: + - description: DSI core clock + - description: RX_ESC clock (used in escape mode) + - description: TX_ESC clock (used in escape mode) + - description: PHY_REF clock + - description: LCDIF clock + + clock-names: + items: + - const: core + - const: rx_esc + - const: tx_esc + - const: phy_ref + - const: lcdif + + mux-controls: + description: + mux controller node to use for operating the input mux + + phys: + maxItems: 1 + description: + A phandle to the phy module representing the DPHY + + phy-names: + items: + - const: dphy + + power-domains: + maxItems: 1 + + resets: + items: + - description: dsi byte reset line + - description: dsi dpi reset line + - description: dsi esc reset line + - description: dsi pclk reset line + + reset-names: + items: + - const: byte + - const: dpi + - const: esc + - const: pclk + + ports: + type: object + description: + A node containing DSI input & output port nodes with endpoint + definitions as documented in + Documentation/devicetree/bindings/graph.txt. + properties: + port@0: + type: object + description: + Input port node to receive pixel data from the + display controller. Exactly one endpoint must be + specified. + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + endpoint@0: + description: sub-node describing the input from LCDIF + type: object + + endpoint@1: + description: sub-node describing the input from DCSS + type: object + + reg: + const: 0 + + required: + - '#address-cells' + - '#size-cells' + - reg + + oneOf: + - required: + - endpoint@0 + - required: + - endpoint@1 + + additionalProperties: false + + port@1: + type: object + description: + DSI output port node to the panel or the next bridge + in the chain + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + required: + - '#address-cells' + - '#size-cells' + - port@0 + - port@1 + + additionalProperties: false + +patternProperties: + "^panel@[0-9]+$": + type: object + +required: + - '#address-cells' + - '#size-cells' + - clock-names + - clocks + - compatible + - interrupts + - mux-controls + - phy-names + - phys + - ports + - reg + - reset-names + - resets + +additionalProperties: false + +examples: + - | + + #include <dt-bindings/clock/imx8mq-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/imx8mq-reset.h> + + mipi_dsi: mipi_dsi@30a00000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx8mq-nwl-dsi"; + reg = <0x30A00000 0x300>; + clocks = <&clk IMX8MQ_CLK_DSI_CORE>, + <&clk IMX8MQ_CLK_DSI_AHB>, + <&clk IMX8MQ_CLK_DSI_IPG_DIV>, + <&clk IMX8MQ_CLK_DSI_PHY_REF>, + <&clk IMX8MQ_CLK_LCDIF_PIXEL>; + clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif"; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + mux-controls = <&mux 0>; + power-domains = <&pgc_mipi>; + resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>, + <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>, + <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>, + <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>; + reset-names = "byte", "dpi", "esc", "pclk"; + phys = <&dphy>; + phy-names = "dphy"; + + panel@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "rocktech,jh057n00900"; + reg = <0>; + port@0 { + reg = <0>; + panel_in: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #size-cells = <0>; + #address-cells = <1>; + reg = <0>; + mipi_dsi_in: endpoint@0 { + reg = <0>; + remote-endpoint = <&lcdif_mipi_dsi>; + }; + }; + port@1 { + reg = <1>; + mipi_dsi_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/ps8640.yaml b/Documentation/devicetree/bindings/display/bridge/ps8640.yaml index 5dff93641bea..7e27cfcf770d 100644 --- a/Documentation/devicetree/bindings/display/bridge/ps8640.yaml +++ b/Documentation/devicetree/bindings/display/bridge/ps8640.yaml @@ -50,6 +50,12 @@ properties: Documentation/devicetree/bindings/media/video-interfaces.txt Documentation/devicetree/bindings/graph.txt properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + port@0: type: object description: | @@ -63,6 +69,8 @@ properties: required: - port@0 + additionalProperties: false + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml b/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml new file mode 100644 index 000000000000..0880cbf217d5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/simple-bridge.yaml @@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/simple-bridge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Transparent non-programmable DRM bridges + +maintainers: + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + - Maxime Ripard <mripard@kernel.org> + +description: | + This binding supports transparent non-programmable bridges that don't require + any configuration, with a single input and a single output. + +properties: + compatible: + oneOf: + - items: + - enum: + - ti,ths8134a + - ti,ths8134b + - const: ti,ths8134 + - enum: + - adi,adv7123 + - dumb-vga-dac + - ti,opa362 + - ti,ths8134 + - ti,ths8135 + + ports: + type: object + description: | + This device has two video ports. Their connections are modeled using the + OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@0: + type: object + description: The bridge input + + port@1: + type: object + description: The bridge output + + required: + - port@0 + - port@1 + + additionalProperties: false + + enable-gpios: + maxItems: 1 + description: GPIO controlling bridge enable + + vdd-supply: + maxItems: 1 + description: Power supply for the bridge + +required: + - compatible + - ports + +additionalProperties: false + +examples: + - | + bridge { + compatible = "ti,ths8134a", "ti,ths8134"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + vga_bridge_in: endpoint { + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port@1 { + reg = <1>; + + vga_bridge_out: endpoint { + remote-endpoint = <&vga_con_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/bridge/snps,dw-mipi-dsi.yaml b/Documentation/devicetree/bindings/display/bridge/snps,dw-mipi-dsi.yaml new file mode 100644 index 000000000000..012aa8e7cb8c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/snps,dw-mipi-dsi.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/snps,dw-mipi-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare MIPI DSI host controller + +maintainers: + - Philippe CORNU <philippe.cornu@st.com> + +description: | + This document defines device tree properties for the Synopsys DesignWare MIPI + DSI host controller. It doesn't constitue a device tree binding specification + by itself but is meant to be referenced by platform-specific device tree + bindings. + + When referenced from platform device tree bindings the properties defined in + this document are defined as follows. The platform device tree bindings are + responsible for defining whether each property is required or optional. + +allOf: + - $ref: ../dsi-controller.yaml# + +properties: + reg: + maxItems: 1 + + clocks: + items: + - description: Module clock + - description: DSI bus clock for either AHB and APB + - description: Pixel clock for the DPI/RGB input + minItems: 2 + + clock-names: + items: + - const: ref + - const: pclk + - const: px_clk + minItems: 2 + + resets: + maxItems: 1 + + reset-names: + const: apb + + ports: + type: object + + properties: + port@0: + type: object + description: Input node to receive pixel data. + port@1: + type: object + description: DSI output node to panel. + + required: + - port@0 + - port@1 + +required: + - clock-names + - clocks + - ports + - reg diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt deleted file mode 100644 index d17d1e5820d7..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt +++ /dev/null @@ -1,66 +0,0 @@ -Thine Electronics THC63LVD1024 LVDS decoder -------------------------------------------- - -The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS streams -to parallel data outputs. The chip supports single/dual input/output modes, -handling up to two LVDS input streams and up to two digital CMOS/TTL outputs. - -Single or dual operation mode, output data mapping and DDR output modes are -configured through input signals and the chip does not expose any control bus. - -Required properties: -- compatible: Shall be "thine,thc63lvd1024" -- vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS input, - PPL and digital circuitry - -Optional properties: -- powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low -- oe-gpios: Output enable GPIO signal, pin name "OE". Active high - -The THC63LVD1024 video port connections are modeled according -to OF graph bindings specified by Documentation/devicetree/bindings/graph.txt - -Required video port nodes: -- port@0: First LVDS input port -- port@2: First digital CMOS/TTL parallel output - -Optional video port nodes: -- port@1: Second LVDS input port -- port@3: Second digital CMOS/TTL parallel output - -The device can operate in single-link mode or dual-link mode. In single-link -mode, all pixels are received on port@0, and port@1 shall not contain any -endpoint. In dual-link mode, even-numbered pixels are received on port@0 and -odd-numbered pixels on port@1, and both port@0 and port@1 shall contain -endpoints. - -Example: --------- - - thc63lvd1024: lvds-decoder { - compatible = "thine,thc63lvd1024"; - - vcc-supply = <®_lvds_vcc>; - powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - lvds_dec_in_0: endpoint { - remote-endpoint = <&lvds_out>; - }; - }; - - port@2{ - reg = <2>; - - lvds_dec_out_2: endpoint { - remote-endpoint = <&adv7511_in>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.yaml b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.yaml new file mode 100644 index 000000000000..469ac4a34273 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/thine,thc63lvd1024.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Thine Electronics THC63LVD1024 LVDS Decoder + +maintainers: + - Jacopo Mondi <jacopo+renesas@jmondi.org> + - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> + +description: | + The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS + streams to parallel data outputs. The chip supports single/dual input/output + modes, handling up to two LVDS input streams and up to two digital CMOS/TTL + outputs. + + Single or dual operation mode, output data mapping and DDR output modes are + configured through input signals and the chip does not expose any control + bus. + +properties: + compatible: + const: thine,thc63lvd1024 + + ports: + type: object + description: | + This device has four video ports. Their connections are modeled using the + OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + + The device can operate in single-link mode or dual-link mode. In + single-link mode, all pixels are received on port@0, and port@1 shall not + contain any endpoint. In dual-link mode, even-numbered pixels are + received on port@0 and odd-numbered pixels on port@1, and both port@0 and + port@1 shall contain endpoints. + + properties: + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + port@0: + type: object + description: First LVDS input port + + port@1: + type: object + description: Second LVDS input port + + port@2: + type: object + description: First digital CMOS/TTL parallel output + + port@3: + type: object + description: Second digital CMOS/TTL parallel output + + required: + - port@0 + - port@2 + + additionalProperties: false + + oe-gpios: + maxItems: 1 + description: Output enable GPIO signal, pin name "OE", active high. + + powerdown-gpios: + maxItems: 1 + description: Power down GPIO signal, pin name "/PDWN", active low. + + vcc-supply: + maxItems: 1 + description: + Power supply for the TTL output, TTL CLOCKOUT signal, LVDS input, PLL and + digital circuitry. + +required: + - compatible + - ports + - vcc-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + lvds-decoder { + compatible = "thine,thc63lvd1024"; + + vcc-supply = <®_lvds_vcc>; + powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_dec_in_0: endpoint { + remote-endpoint = <&lvds_out>; + }; + }; + + port@2 { + reg = <2>; + + lvds_dec_out_2: endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/bridge/ti,ths813x.txt b/Documentation/devicetree/bindings/display/bridge/ti,ths813x.txt deleted file mode 100644 index df3d7c1ac09e..000000000000 --- a/Documentation/devicetree/bindings/display/bridge/ti,ths813x.txt +++ /dev/null @@ -1,51 +0,0 @@ -THS8134 and THS8135 Video DAC ------------------------------ - -This is the binding for Texas Instruments THS8134, THS8134A, THS8134B and -THS8135 Video DAC bridges. - -Required properties: - -- compatible: Must be one of - "ti,ths8134" - "ti,ths8134a," "ti,ths8134" - "ti,ths8134b", "ti,ths8134" - "ti,ths8135" - -Required nodes: - -This device has two video ports. Their connections are modelled using the OF -graph bindings specified in Documentation/devicetree/bindings/graph.txt. - -- Video port 0 for RGB input -- Video port 1 for VGA output - -Example -------- - -vga-bridge { - compatible = "ti,ths8135"; - #address-cells = <1>; - #size-cells = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - - vga_bridge_in: endpoint { - remote-endpoint = <&lcdc_out_vga>; - }; - }; - - port@1 { - reg = <1>; - - vga_bridge_out: endpoint { - remote-endpoint = <&vga_con_in>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/dsi-controller.yaml b/Documentation/devicetree/bindings/display/dsi-controller.yaml index fd986c36c737..85b71b1fd28a 100644 --- a/Documentation/devicetree/bindings/display/dsi-controller.yaml +++ b/Documentation/devicetree/bindings/display/dsi-controller.yaml @@ -28,7 +28,7 @@ description: | properties: $nodename: - pattern: "^dsi-controller(@.*)?$" + pattern: "^dsi(@.*)?$" "#address-cells": const: 1 @@ -76,7 +76,7 @@ patternProperties: examples: - | #include <dt-bindings/gpio/gpio.h> - dsi-controller@a0351000 { + dsi@a0351000 { reg = <0xa0351000 0x1000>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt index 58914cf681b8..77def4456706 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -17,6 +17,9 @@ Required properties: Documentation/devicetree/bindings/graph.txt. This port should be connected to the input port of an attached HDMI or LVDS encoder chip. +Optional properties: +- pinctrl-names: Contain "default" and "sleep". + Example: dpi0: dpi@1401d000 { @@ -27,6 +30,9 @@ dpi0: dpi@1401d000 { <&mmsys CLK_MM_DPI_ENGINE>, <&apmixedsys CLK_APMIXED_TVDPLL>; clock-names = "pixel", "engine", "pll"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dpi_pin_func>; + pinctrl-1 = <&dpi_pin_idle>; port { dpi0_out: endpoint { diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt index a19a6cc375ed..8e4729de8c85 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -33,6 +33,13 @@ Required properties: - #clock-cells: must be <0>; - #phy-cells: must be <0>. +Optional properties: +- drive-strength-microamp: adjust driving current, should be 3000 ~ 6000. And + the step is 200. +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calibration-data" + Example: mipi_tx0: mipi-dphy@10215000 { @@ -42,6 +49,9 @@ mipi_tx0: mipi-dphy@10215000 { clock-output-names = "mipi_tx0_pll"; #clock-cells = <0>; #phy-cells = <0>; + drive-strength-microamp = <4600>; + nvmem-cells= <&mipi_tx_calibration>; + nvmem-cell-names = "calibration-data"; }; dsi0: dsi@1401b000 { diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt deleted file mode 100644 index 0601a9e34703..000000000000 --- a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt +++ /dev/null @@ -1,31 +0,0 @@ -ARM Versatile TFT Panels - -These panels are connected to the daughterboards found on the -ARM Versatile reference designs. - -This device node must appear as a child to a "syscon"-compatible -node. - -Required properties: -- compatible: should be "arm,versatile-tft-panel" - -Required subnodes: -- port: see display/panel/panel-common.yaml, graph.txt - - -Example: - -sysreg@0 { - compatible = "arm,versatile-sysreg", "syscon", "simple-mfd"; - reg = <0x00000 0x1000>; - - panel: display@0 { - compatible = "arm,versatile-tft-panel"; - - port { - panel_in: endpoint { - remote-endpoint = <&foo>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.yaml b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.yaml new file mode 100644 index 000000000000..41fd5713c156 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/arm,versatile-tft-panel.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Versatile TFT Panels + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + These panels are connected to the daughterboards found on the + ARM Versatile reference designs. + + This device node must appear as a child to a "syscon"-compatible + node. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: arm,versatile-tft-panel + + port: true + +required: + - compatible + - port + +additionalProperties: false + +examples: + - | + sysreg { + compatible = "arm,versatile-sysreg", "syscon", "simple-mfd"; + reg = <0x00000 0x1000>; + + #address-cells = <1>; + #size-cells = <0>; + + panel { + compatible = "arm,versatile-tft-panel"; + + port { + panel_in: endpoint { + remote-endpoint = <&foo>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/asus,z00t-tm5p5-nt35596.yaml b/Documentation/devicetree/bindings/display/panel/asus,z00t-tm5p5-nt35596.yaml new file mode 100644 index 000000000000..083d2b9d0c69 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/asus,z00t-tm5p5-nt35596.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/asus,z00t-tm5p5-nt35596.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASUS Z00T TM5P5 NT35596 5.5" 1080×1920 LCD Panel + +maintainers: + - Konrad Dybcio <konradybcio@gmail.com> + +description: |+ + This panel seems to only be found in the Asus Z00T + smartphone and we have no straightforward way of + actually getting the correct model number, + as no schematics are released publicly. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: asus,z00t-tm5p5-n35596 + reg: true + reset-gpios: true + vdd-supply: + description: core voltage supply + vddio-supply: + description: vddio supply + +required: + - compatible + - reg + - vdd-supply + - vddio-supply + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + reg = <0>; + + compatible = "asus,z00t-tm5p5-n35596"; + + vdd-supply = <&pm8916_l8>; + vddio-supply = <&pm8916_l6>; + reset-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt b/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt deleted file mode 100644 index 3caea2172b1b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/boe,himax8279d.txt +++ /dev/null @@ -1,24 +0,0 @@ -Boe Himax8279d 1200x1920 TFT LCD panel - -Required properties: -- compatible: should be "boe,himax8279d8p" and one of: "boe,himax8279d10p" -- reg: DSI virtual channel of the peripheral -- enable-gpios: panel enable gpio -- pp33-gpios: a GPIO phandle for the 3.3v pin that provides the supply voltage -- pp18-gpios: a GPIO phandle for the 1.8v pin that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - &mipi_dsi { - panel { - compatible = "boe,himax8279d8p", "boe,himax8279d10p"; - reg = <0>; - backlight = <&backlight>; - enable-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; - pp33-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; - pp18-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml b/Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml new file mode 100644 index 000000000000..272a3a018a33 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/boe,himax8279d.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/boe,himax8279d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Boe Himax8279d 1200x1920 TFT LCD panel + +maintainers: + - Jerry Han <jerry.han.hq@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + items: + - const: boe,himax8279d8p + - const: boe,himax8279d10p + + backlight: true + enable-gpios: true + reg: true + + pp33-gpios: + maxItems: 1 + description: GPIO for the 3.3v pin that provides the supply voltage + + pp18-gpios: + maxItems: 1 + description: GPIO for the 1.8v pin that provides the supply voltage + +required: + - compatible + - reg + - enable-gpios + - pp33-gpios + - pp18-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "boe,himax8279d8p", "boe,himax8279d10p"; + reg = <0>; + backlight = <&backlight>; + enable-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + pp33-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; + pp18-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/boe,tv101wum-nl6.yaml b/Documentation/devicetree/bindings/display/panel/boe,tv101wum-nl6.yaml index 740213459134..7f5df5851017 100644 --- a/Documentation/devicetree/bindings/display/panel/boe,tv101wum-nl6.yaml +++ b/Documentation/devicetree/bindings/display/panel/boe,tv101wum-nl6.yaml @@ -24,6 +24,8 @@ properties: - boe,tv101wum-n53 # AUO B101UAN08.3 10.1" WUXGA TFT LCD panel - auo,b101uan08.3 + # BOE TV105WUM-NW0 10.5" WUXGA TFT LCD panel + - boe,tv105wum-nw0 reg: description: the virtual channel number of a DSI peripheral diff --git a/Documentation/devicetree/bindings/display/panel/display-timings.yaml b/Documentation/devicetree/bindings/display/panel/display-timings.yaml index c8c0c9cb0492..56903ded005e 100644 --- a/Documentation/devicetree/bindings/display/panel/display-timings.yaml +++ b/Documentation/devicetree/bindings/display/panel/display-timings.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/display/panel/display-timings.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: display timing bindings +title: display timings bindings maintainers: - Thierry Reding <thierry.reding@gmail.com> @@ -14,7 +14,7 @@ maintainers: description: | A display panel may be able to handle several display timings, with different resolutions. - The display-timings node makes it possible to specify the timing + The display-timings node makes it possible to specify the timings and to specify the timing that is native for the display. properties: @@ -25,8 +25,8 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle description: | The default display timing is the one specified as native-mode. - If no native-mode is specified then the first node is assumed the - native mode. + If no native-mode is specified then the first node is assumed + to be the native mode. patternProperties: "^timing": diff --git a/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt b/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt deleted file mode 100644 index 82caa7b65ae8..000000000000 --- a/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt +++ /dev/null @@ -1,20 +0,0 @@ -Feiyang FY07024DI26A30-D 7" MIPI-DSI LCD Panel - -Required properties: -- compatible: must be "feiyang,fy07024di26a30d" -- reg: DSI virtual channel used by that screen -- avdd-supply: analog regulator dc1 switch -- dvdd-supply: 3v3 digital regulator -- reset-gpios: a GPIO phandle for the reset pin - -Optional properties: -- backlight: phandle for the backlight control. - -panel@0 { - compatible = "feiyang,fy07024di26a30d"; - reg = <0>; - avdd-supply = <®_dc1sw>; - dvdd-supply = <®_dldo2>; - reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ - backlight = <&backlight>; -}; diff --git a/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.yaml b/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.yaml new file mode 100644 index 000000000000..95acf9e96f1c --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/feiyang,fy07024di26a30d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Feiyang FY07024DI26A30-D 7" MIPI-DSI LCD Panel + +maintainers: + - Jagan Teki <jagan@amarulasolutions.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: feiyang,fy07024di26a30d + + reg: + description: DSI virtual channel used by that screen + maxItems: 1 + + avdd-supply: + description: analog regulator dc1 switch + + dvdd-supply: + description: 3v3 digital regulator + + reset-gpios: true + + backlight: true + +required: + - compatible + - reg + - avdd-supply + - dvdd-supply + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "feiyang,fy07024di26a30d"; + reg = <0>; + avdd-supply = <®_dc1sw>; + dvdd-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt deleted file mode 100644 index 3d5ce6ad6ec7..000000000000 --- a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt +++ /dev/null @@ -1,49 +0,0 @@ -Ilitek ILI9322 TFT panel driver with SPI control bus - -This is a driver for 320x240 TFT panels, accepting a variety of input -streams that get adapted and scaled to the panel. The panel output has -960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and -VCOMH outputs. - -Required properties: - - compatible: "dlink,dir-685-panel", "ilitek,ili9322" - (full system-specific compatible is always required to look up configuration) - - reg: address of the panel on the SPI bus - -Optional properties: - - vcc-supply: core voltage supply, see regulator/regulator.txt - - iovcc-supply: voltage supply for the interface input/output signals, - see regulator/regulator.txt - - vci-supply: voltage supply for analog parts, see regulator/regulator.txt - - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt - - The following optional properties only apply to RGB and YUV input modes and - can be omitted for BT.656 input modes: - - - pixelclk-active: see display/panel/display-timing.txt - - de-active: see display/panel/display-timing.txt - - hsync-active: see display/panel/display-timing.txt - - vsync-active: see display/panel/display-timing.txt - -The panel must obey the rules for a SPI slave device as specified in -spi/spi-bus.txt - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in -media/video-interfaces.txt. This node should describe panel's video bus. - -Example: - -panel: display@0 { - compatible = "dlink,dir-685-panel", "ilitek,ili9322"; - reg = <0>; - vcc-supply = <&vdisp>; - iovcc-supply = <&vdisp>; - vci-supply = <&vdisp>; - - port { - panel_in: endpoint { - remote-endpoint = <&display_out>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml new file mode 100644 index 000000000000..177d48c5bd97 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/ilitek,ili9322.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ilitek ILI9322 TFT panel driver with SPI control bus + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + This is a driver for 320x240 TFT panels, accepting a variety of input + streams that get adapted and scaled to the panel. The panel output has + 960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and + VCOMH outputs. + + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + items: + - enum: + - dlink,dir-685-panel + + - const: ilitek,ili9322 + + reset-gpios: true + port: true + + vcc-supply: + description: Core voltage supply + + iovcc-supply: + description: Voltage supply for the interface input/output signals + + vci-supply: + description: Voltage supply for analog parts + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel: display@0 { + compatible = "dlink,dir-685-panel", "ilitek,ili9322"; + reg = <0>; + vcc-supply = <&vdisp>; + iovcc-supply = <&vdisp>; + vci-supply = <&vdisp>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt deleted file mode 100644 index 4a041acb4e18..000000000000 --- a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt +++ /dev/null @@ -1,20 +0,0 @@ -Ilitek ILI9881c based MIPI-DSI panels - -Required properties: - - compatible: must be "ilitek,ili9881c" and one of: - * "bananapi,lhr050h41" - - reg: DSI virtual channel used by that screen - - power-supply: phandle to the power regulator - - reset-gpios: a GPIO phandle for the reset pin - -Optional properties: - - backlight: phandle to the backlight used - -Example: -panel@0 { - compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; - reg = <0>; - power-supply = <®_display>; - reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ - backlight = <&pwm_bl>; -}; diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml new file mode 100644 index 000000000000..a39332276bab --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/ilitek,ili9881c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ilitek ILI9881c based MIPI-DSI panels + +maintainers: + - Maxime Ripard <mripard@kernel.org> + +properties: + compatible: + items: + - enum: + - bananapi,lhr050h41 + + - const: ilitek,ili9881c + + backlight: true + power-supply: true + reg: true + reset-gpios: true + +required: + - compatible + - power-supply + - reg + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; + reg = <0>; + power-supply = <®_display>; + reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ + backlight = <&pwm_bl>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt b/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt deleted file mode 100644 index d1cab3a8f0fb..000000000000 --- a/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt +++ /dev/null @@ -1,24 +0,0 @@ -Innolux P097PFG 9.7" 1536x2048 TFT LCD panel - -Required properties: -- compatible: should be "innolux,p097pfg" -- reg: DSI virtual channel of the peripheral -- avdd-supply: phandle of the regulator that provides positive voltage -- avee-supply: phandle of the regulator that provides negative voltage -- enable-gpios: panel enable gpio - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - &mipi_dsi { - panel@0 { - compatible = "innolux,p079zca"; - reg = <0>; - avdd-supply = <...>; - avee-supply = <...>; - backlight = <&backlight>; - enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.yaml b/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.yaml new file mode 100644 index 000000000000..5a5f071627fb --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/innolux,p097pfg.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Innolux P097PFG 9.7" 1536x2048 TFT LCD panel + +maintainers: + - Lin Huang <hl@rock-chips.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: innolux,p097pfg + + backlight: true + enable-gpios: true + reg: true + + avdd-supply: + description: The regulator that provides positive voltage + + avee-supply: + description: The regulator that provides negative voltage + +required: + - compatible + - reg + - avdd-supply + - avee-supply + - enable-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "innolux,p097pfg"; + reg = <0>; + avdd-supply = <&avdd>; + avee-supply = <&avee>; + backlight = <&backlight>; + enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt deleted file mode 100644 index 513f03466aba..000000000000 --- a/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.txt +++ /dev/null @@ -1,22 +0,0 @@ -Innolux P120ZDG-BF1 12.02 inch eDP 2K display panel - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. - -Required properties: -- compatible: should be "innolux,p120zdg-bf1" -- power-supply: regulator to provide the supply voltage - -Optional properties: -- enable-gpios: GPIO pin to enable or disable the panel -- backlight: phandle of the backlight device attached to the panel -- no-hpd: If HPD isn't hooked up; add this property. - -Example: - panel_edp: panel-edp { - compatible = "innolux,p120zdg-bf1"; - enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>; - power-supply = <&pm8916_l2>; - backlight = <&backlight>; - no-hpd; - }; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.yaml b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.yaml new file mode 100644 index 000000000000..243dac2416f3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,p120zdg-bf1.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/innolux,p120zdg-bf1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Innolux P120ZDG-BF1 12.02 inch eDP 2K display panel + +maintainers: + - Sandeep Panda <spanda@codeaurora.org> + - Douglas Anderson <dianders@chromium.org> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: innolux,p120zdg-bf1 + + enable-gpios: true + power-supply: true + backlight: true + no-hpd: true + +required: + - compatible + - power-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + panel_edp: panel-edp { + compatible = "innolux,p120zdg-bf1"; + enable-gpios = <&msmgpio 31 GPIO_ACTIVE_LOW>; + power-supply = <&pm8916_l2>; + backlight = <&backlight>; + no-hpd; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt deleted file mode 100644 index 4989c91d505f..000000000000 --- a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt +++ /dev/null @@ -1,31 +0,0 @@ -JDI model LT070ME05000 1200x1920 7" DSI Panel - -Required properties: -- compatible: should be "jdi,lt070me05000" -- vddp-supply: phandle of the regulator that provides the supply voltage - Power IC supply (3-5V) -- iovcc-supply: phandle of the regulator that provides the supply voltage - IOVCC , power supply for LCM (1.8V) -- enable-gpios: phandle of gpio for enable line - LED_EN, LED backlight enable, High active -- reset-gpios: phandle of gpio for reset line - This should be 8mA, gpio can be configured using mux, pinctrl, pinctrl-names - XRES, Reset, Low active -- dcdc-en-gpios: phandle of the gpio for power ic line - Power IC supply enable, High active - -Example: - - dsi0: qcom,mdss_dsi@4700000 { - panel@0 { - compatible = "jdi,lt070me05000"; - reg = <0>; - - vddp-supply = <&pm8921_l17>; - iovcc-supply = <&pm8921_lvs7>; - - enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>; - reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>; - dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.yaml b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.yaml new file mode 100644 index 000000000000..b8b9435e464c --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/jdi,lt070me05000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: JDI model LT070ME05000 1200x1920 7" DSI Panel + +maintainers: + - Vinay Simha BN <simhavcs@gmail.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: jdi,lt070me05000 + + enable-gpios: true + reg: true + reset-gpios: true + + vddp-supply: + description: | + The regulator that provides the supply voltage Power IC supply (3-5V) + + iovcc-supply: + description: | + The regulator that provides the supply voltage IOVCC, + power supply for LCM (1.8V) + + dcdc-en-gpios: + description: | + phandle of the gpio for power ic line + Power IC supply enable, High active + +required: + - compatible + - reg + - vddp-supply + - iovcc-supply + - enable-gpios + - reset-gpios + - dcdc-en-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "jdi,lt070me05000"; + reg = <0>; + + vddp-supply = <&pm8921_l17>; + iovcc-supply = <&pm8921_lvs7>; + + enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>; + dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt deleted file mode 100644 index fa9596082e44..000000000000 --- a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.txt +++ /dev/null @@ -1,42 +0,0 @@ -King Display KD035G6-54NT 3.5" (320x240 pixels) 24-bit TFT LCD panel - -Required properties: -- compatible: should be "kingdisplay,kd035g6-54nt" -- power-supply: See panel-common.txt -- reset-gpios: See panel-common.txt - -Optional properties: -- backlight: see panel-common.txt - -The generic bindings for the SPI slaves documented in [1] also apply. - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in [2]. This -node should describe panel's video bus. - -[1]: Documentation/devicetree/bindings/spi/spi-bus.txt -[2]: Documentation/devicetree/bindings/graph.txt - -Example: - -&spi { - panel@0 { - compatible = "kingdisplay,kd035g6-54nt"; - reg = <0>; - - spi-max-frequency = <3125000>; - spi-3wire; - spi-cs-high; - - reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>; - - backlight = <&backlight>; - power-supply = <&ldo6>; - - port { - panel_input: endpoint { - remote-endpoint = <&panel_output>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.yaml b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.yaml new file mode 100644 index 000000000000..6960036975fa --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/kingdisplay,kd035g6-54nt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: King Display KD035G6-54NT 3.5" (320x240 pixels) 24-bit TFT LCD panel + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: kingdisplay,kd035g6-54nt + + backlight: true + port: true + power-supply: true + reg: true + reset-gpios: true + +required: + - compatible + - power-supply + - reset-gpios + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "kingdisplay,kd035g6-54nt"; + reg = <0>; + + spi-max-frequency = <3125000>; + spi-3wire; + spi-cs-high; + + reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>; + + backlight = <&backlight>; + power-supply = <&ldo6>; + + port { + panel_input: endpoint { + remote-endpoint = <&panel_output>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt deleted file mode 100644 index cfefff688614..000000000000 --- a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt +++ /dev/null @@ -1,22 +0,0 @@ -Kingdisplay KD097D04 9.7" 1536x2048 TFT LCD panel - -Required properties: -- compatible: should be "kingdisplay,kd097d04" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage -- enable-gpios: panel enable gpio - -Optional properties: -- backlight: phandle of the backlight device attached to the panel - -Example: - - &mipi_dsi { - panel@0 { - compatible = "kingdisplay,kd097d04"; - reg = <0>; - power-supply = <...>; - backlight = <&backlight>; - enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/leadtek,ltk050h3146w.yaml b/Documentation/devicetree/bindings/display/panel/leadtek,ltk050h3146w.yaml new file mode 100644 index 000000000000..a372bdc5bde1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/leadtek,ltk050h3146w.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/leadtek,ltk050h3146w.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Leadtek LTK050H3146W 5.0in 720x1280 DSI panel + +maintainers: + - Heiko Stuebner <heiko.stuebner@theobroma-systems.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + - leadtek,ltk050h3146w + - leadtek,ltk050h3146w-a2 + reg: true + backlight: true + reset-gpios: true + iovcc-supply: + description: regulator that supplies the iovcc voltage + vci-supply: + description: regulator that supplies the vci voltage + +required: + - compatible + - reg + - backlight + - iovcc-supply + - vci-supply + +additionalProperties: false + +examples: + - | + dsi { + #address-cells = <1>; + #size-cells = <0>; + panel@0 { + compatible = "leadtek,ltk050h3146w"; + reg = <0>; + backlight = <&backlight>; + iovcc-supply = <&vcc_1v8>; + vci-supply = <&vcc3v3_lcd>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/leadtek,ltk500hd1829.yaml b/Documentation/devicetree/bindings/display/panel/leadtek,ltk500hd1829.yaml index fd931b293816..b900973b5f7b 100644 --- a/Documentation/devicetree/bindings/display/panel/leadtek,ltk500hd1829.yaml +++ b/Documentation/devicetree/bindings/display/panel/leadtek,ltk500hd1829.yaml @@ -37,7 +37,6 @@ examples: dsi { #address-cells = <1>; #size-cells = <0>; - reg = <0xff450000 0x1000>; panel@0 { compatible = "leadtek,ltk500hd1829"; diff --git a/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt b/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt deleted file mode 100644 index fc1e1b325e49..000000000000 --- a/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt +++ /dev/null @@ -1,7 +0,0 @@ -LG ACX467AKM-7 4.95" 1080×1920 LCD Panel - -Required properties: -- compatible: must be "lg,acx467akm-7" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt b/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt deleted file mode 100644 index 5e649cb9aa1a..000000000000 --- a/Documentation/devicetree/bindings/display/panel/lg,ld070wx3-sl01.txt +++ /dev/null @@ -1,7 +0,0 @@ -LG Corporation 7" WXGA TFT LCD panel - -Required properties: -- compatible: should be "lg,ld070wx3-sl01" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt b/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt deleted file mode 100644 index 824441f4e95a..000000000000 --- a/Documentation/devicetree/bindings/display/panel/lg,lg4573.txt +++ /dev/null @@ -1,19 +0,0 @@ -LG LG4573 TFT Liquid Crystal Display with SPI control bus - -Required properties: - - compatible: "lg,lg4573" - - reg: address of the panel on the SPI bus - -The panel must obey rules for SPI slave device specified in document [1]. - -[1]: Documentation/devicetree/bindings/spi/spi-bus.txt - -Example: - - lcd_panel: display@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lg,lg4573"; - spi-max-frequency = <10000000>; - reg = <0>; - }; diff --git a/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml b/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml new file mode 100644 index 000000000000..b4314ce7b411 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/lg,lg4573.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LG LG4573 TFT Liquid Crystal Display with SPI control bus + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Heiko Schocher <hs@denx.de> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: lg,lg4573 + + reg: true + spi-max-frequency: true + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + lcd_panel: display@0 { + compatible = "lg,lg4573"; + spi-max-frequency = <10000000>; + reg = <0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt b/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt deleted file mode 100644 index a04fd2b2e73d..000000000000 --- a/Documentation/devicetree/bindings/display/panel/lg,lh500wx1-sd03.txt +++ /dev/null @@ -1,7 +0,0 @@ -LG Corporation 5" HD TFT LCD panel - -Required properties: -- compatible: should be "lg,lh500wx1-sd03" - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt b/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt deleted file mode 100644 index 1a1e653e5407..000000000000 --- a/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.txt +++ /dev/null @@ -1,33 +0,0 @@ -LG.Philips LB035Q02 Panel -========================= - -Required properties: -- compatible: "lgphilips,lb035q02" -- enable-gpios: panel enable gpio - -Optional properties: -- label: a symbolic name for the panel - -Required nodes: -- Video port for DPI input - -Example -------- - -lcd-panel: panel@0 { - compatible = "lgphilips,lb035q02"; - reg = <0>; - spi-max-frequency = <100000>; - spi-cpol; - spi-cpha; - - label = "lcd"; - - enable-gpios = <&gpio7 7 0>; - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.yaml b/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.yaml new file mode 100644 index 000000000000..830e335ddb53 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lgphilips,lb035q02.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/lgphilips,lb035q02.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LG.Philips LB035Q02 Panel + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ti.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: lgphilips,lb035q02 + + label: true + enable-gpios: true + port: true + +required: + - compatible + - enable-gpios + - port + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel: panel@0 { + compatible = "lgphilips,lb035q02"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + enable-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/lvds.yaml b/Documentation/devicetree/bindings/display/panel/lvds.yaml index d0083301acbe..946dd354256c 100644 --- a/Documentation/devicetree/bindings/display/panel/lvds.yaml +++ b/Documentation/devicetree/bindings/display/panel/lvds.yaml @@ -96,12 +96,20 @@ properties: If set, reverse the bit order described in the data mappings below on all data lanes, transmitting bits for slots 6 to 0 instead of 0 to 6. + port: true + ports: true + required: - compatible - data-mapping - width-mm - height-mm - panel-timing - - port + +oneOf: + - required: + - port + - required: + - ports ... diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.txt deleted file mode 100644 index a89f9c830a85..000000000000 --- a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.txt +++ /dev/null @@ -1,42 +0,0 @@ -Binding for Olimex Ltd. LCD-OLinuXino bridge panel. - -This device can be used as bridge between a host controller and LCD panels. -Currently supported LCDs are: - - LCD-OLinuXino-4.3TS - - LCD-OLinuXino-5 - - LCD-OLinuXino-7 - - LCD-OLinuXino-10 - -The panel itself contains: - - AT24C16C EEPROM holding panel identification and timing requirements - - AR1021 resistive touch screen controller (optional) - - FT5x6 capacitive touch screnn controller (optional) - - GT911/GT928 capacitive touch screen controller (optional) - -The above chips share same I2C bus. The EEPROM is factory preprogrammed with -device information (id, serial, etc.) and timing requirements. - -Touchscreen bingings can be found in these files: - - input/touchscreen/goodix.txt - - input/touchscreen/edt-ft5x06.txt - - input/touchscreen/ar1021.txt - -Required properties: - - compatible: should be "olimex,lcd-olinuxino" - - reg: address of the configuration EEPROM, should be <0x50> - - power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: - - enable-gpios: GPIO pin to enable or disable the panel - - backlight: phandle of the backlight device attacked to the panel - -Example: -&i2c2 { - panel@50 { - compatible = "olimex,lcd-olinuxino"; - reg = <0x50>; - power-supply = <®_vcc5v0>; - enable-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; - backlight = <&backlight>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.yaml b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.yaml new file mode 100644 index 000000000000..2329d9610f83 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/olimex,lcd-olinuxino.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Olimex Ltd. LCD-OLinuXino bridge panel. + +maintainers: + - Stefan Mavrodiev <stefan@olimex.com> + +description: | + This device can be used as bridge between a host controller and LCD panels. + Currently supported LCDs are: + - LCD-OLinuXino-4.3TS + - LCD-OLinuXino-5 + - LCD-OLinuXino-7 + - LCD-OLinuXino-10 + + The panel itself contains: + - AT24C16C EEPROM holding panel identification and timing requirements + - AR1021 resistive touch screen controller (optional) + - FT5x6 capacitive touch screnn controller (optional) + - GT911/GT928 capacitive touch screen controller (optional) + + The above chips share same I2C bus. The EEPROM is factory preprogrammed with + device information (id, serial, etc.) and timing requirements. + + Touchscreen bingings can be found in these files: + - input/touchscreen/goodix.yaml + - input/touchscreen/edt-ft5x06.txt + - input/touchscreen/ar1021.txt + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: olimex,lcd-olinuxino + + backlight: true + enable-gpios: true + power-supply: true + reg: true + +required: + - compatible + - reg + - power-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + panel@50 { + compatible = "olimex,lcd-olinuxino"; + reg = <0x50>; + power-supply = <®_vcc5v0>; + enable-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; + backlight = <&backlight>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt b/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt deleted file mode 100644 index 9d88e96003fc..000000000000 --- a/Documentation/devicetree/bindings/display/panel/osddisplays,osd101t2587-53ts.txt +++ /dev/null @@ -1,14 +0,0 @@ -One Stop Displays OSD101T2587-53TS 10.1" 1920x1200 panel - -The panel is similar to OSD101T2045-53TS, but it needs additional -MIPI_DSI_TURN_ON_PERIPHERAL message from the host. - -Required properties: -- compatible: should be "osddisplays,osd101t2587-53ts" -- power-supply: as specified in the base binding - -Optional properties: -- backlight: as specified in the base binding - -This binding is compatible with the simple-panel binding, which is specified -in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml index ed051ba12084..45fe8fe5faba 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-common.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml @@ -48,9 +48,8 @@ properties: rotation: description: Display rotation in degrees counter clockwise (0,90,180,270) - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - enum: [ 0, 90, 180, 270 ] + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 90, 180, 270] # Display Timings panel-timing: @@ -58,16 +57,14 @@ properties: Most display panels are restricted to a single resolution and require specific display timings. The panel-timing subnode expresses those timings. - allOf: - - $ref: panel-timing.yaml# + $ref: panel-timing.yaml# display-timings: description: - Some display panels supports several resolutions with different timing. + Some display panels support several resolutions with different timings. The display-timings bindings supports specifying several timings and - optional specify which is the native mode. - allOf: - - $ref: display-timings.yaml# + optionally specifying which is the native mode. + $ref: display-timings.yaml# # Connectivity port: @@ -96,6 +93,12 @@ properties: (hot plug detect) signal, but the signal isn't hooked up so we should hardcode the max delay from the panel spec when powering up the panel. + hpd-gpios: + maxItems: 1 + description: + If Hot Plug Detect (HPD) is connected to a GPIO in the system rather + than a dedicated HPD pin the pin can be specified here. + # Control I/Os # Many display panels can be controlled through pins driven by GPIOs. The nature @@ -124,6 +127,13 @@ properties: while active. Active high reset signals can be supported by inverting the GPIO specifier polarity flag. + te-gpios: + maxItems: 1 + description: + GPIO spec for the tearing effect synchronization signal. + The tearing effect signal is active high. Active low signals can be + supported by inverting the GPIO specifier polarity flag. + # Power power-supply: description: diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml index b2e8742fd6af..16778ce782fc 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple-dsi.yaml @@ -29,6 +29,20 @@ properties: # compatible must be listed in alphabetical order, ordered by compatible. # The description in the comment is mandatory for each compatible. + # AU Optronics Corporation 8.0" WUXGA TFT LCD panel + - auo,b080uan01 + # Boe Corporation 8.0" WUXGA TFT LCD panel + - boe,tv080wum-nl0 + # Kingdisplay KD097D04 9.7" 1536x2048 TFT LCD panel + - kingdisplay,kd097d04 + # LG ACX467AKM-7 4.95" 1080×1920 LCD Panel + - lg,acx467akm-7 + # LG Corporation 7" WXGA TFT LCD panel + - lg,ld070wx3-sl01 + # One Stop Displays OSD101T2587-53TS 10.1" 1920x1200 panel + - osddisplays,osd101t2587-53ts + # Panasonic 10" WUXGA TFT LCD panel + - panasonic,vvx10f004b00 # Panasonic 10" WUXGA TFT LCD panel - panasonic,vvx10f034n00 diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index 393ffc6acbba..d6cca1479633 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -33,8 +33,6 @@ properties: - ampire,am-480272h3tmqw-t01h # Ampire AM-800480R3TMQW-A1H 7.0" WVGA TFT LCD panel - ampire,am800480r3tmqwa1h - # AU Optronics Corporation 8.0" WUXGA TFT LCD panel - - auo,b080uan01 # AU Optronics Corporation 10.1" WSVGA TFT LCD panel - auo,b101aw03 # AU Optronics Corporation 10.1" WSVGA TFT LCD panel @@ -55,10 +53,16 @@ properties: - auo,g101evn010 # AU Optronics Corporation 10.4" (800x600) color TFT LCD panel - auo,g104sn02 + # AU Optronics Corporation 12.1" (1280x800) TFT LCD panel + - auo,g121ean01 # AU Optronics Corporation 13.3" FHD (1920x1080) TFT LCD panel - auo,g133han01 + # AU Optronics Corporation 15.6" (1366x768) TFT LCD panel + - auo,g156xtn01 # AU Optronics Corporation 18.5" FHD (1920x1080) TFT LCD panel - auo,g185han01 + # AU Optronics Corporation 19.0" (1280x1024) TFT LCD panel + - auo,g190ean01 # AU Optronics Corporation 31.5" FHD (1920x1080) TFT LCD panel - auo,p320hvn03 # AU Optronics Corporation 21.5" FHD (1920x1080) color TFT LCD panel @@ -69,10 +73,12 @@ properties: - boe,hv070wsa-100 # BOE OPTOELECTRONICS TECHNOLOGY 10.1" WXGA TFT LCD panel - boe,nv101wxmn51 + # BOE NV133FHM-N61 13.3" FHD (1920x1080) TFT LCD Panel + - boe,nv133fhm-n61 + # BOE NV133FHM-N62 13.3" FHD (1920x1080) TFT LCD Panel + - boe,nv133fhm-n62 # BOE NV140FHM-N49 14.0" FHD a-Si FT panel - boe,nv140fhmn49 - # Boe Corporation 8.0" WUXGA TFT LCD panel - - boe,tv080wum-nl0 # CDTech(H.K.) Electronics Limited 4.3" 480x272 color TFT-LCD panel - cdtech,s043wq26h-ct7 # CDTech(H.K.) Electronics Limited 7" 800x480 color TFT-LCD panel @@ -82,6 +88,8 @@ properties: # Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel - chunghwa,claa101wa01a # Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel + - chunghwa,claa101wb01 + # Chunghwa Picture Tubes Ltd. 10.1" WXGA TFT LCD panel - chunghwa,claa101wb03 # DataImage, Inc. 7" WVGA (800x480) TFT LCD panel with 24-bit parallel interface. - dataimage,scf0700c48ggu18 @@ -127,6 +135,8 @@ properties: - hannstar,hsd100pxn1 # Hitachi Ltd. Corporation 9" WVGA (800x480) TFT LCD panel - hit,tx23d38vm0caa + # InfoVision Optoelectronics M133NWF4 R0 13.3" FHD (1920x1080) TFT LCD panel + - ivo,m133nwf4-r0 # Innolux AT043TN24 4.3" WQVGA TFT LCD panel - innolux,at043tn24 # Innolux AT070TN92 7.0" WQVGA TFT LCD panel @@ -155,6 +165,8 @@ properties: - lemaker,bl035-rgb-002 # LG 7" (800x480 pixels) TFT LCD panel - lg,lb070wv8 + # LG Corporation 5" HD TFT LCD panel + - lg,lh500wx1-sd03 # LG LP079QX1-SP0V 7.9" (1536x2048 pixels) TFT LCD panel - lg,lp079qx1-sp0v # LG 9.7" (2048x1536 pixels) TFT LCD panel @@ -227,6 +239,8 @@ properties: - sharp,ls020b1dd01d # Shelly SCA07010-BFN-LNN 7.0" WVGA TFT LCD panel - shelly,sca07010-bfn-lnn + # Starry KR070PE2T 7" WVGA TFT LCD panel + - starry,kr070pe2t # Starry 12.2" (1920x1200 pixels) TFT LCD panel - starry,kr122ea0sra # Tianma Micro-electronics TM070JDHG30 7.0" WXGA TFT LCD panel diff --git a/Documentation/devicetree/bindings/display/panel/panel-timing.yaml b/Documentation/devicetree/bindings/display/panel/panel-timing.yaml index bd558ad7891f..182c19cb7fdd 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-timing.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-timing.yaml @@ -72,92 +72,80 @@ properties: hfront-porch: description: Horizontal front porch panel timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of pixels - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of pixels hback-porch: description: Horizontal back porch timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of pixels - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of pixels hsync-len: description: Horizontal sync length panel timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of pixels - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of pixels + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of pixels vfront-porch: description: Vertical front porch panel timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of lines - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of lines + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of lines + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of lines vback-porch: description: Vertical back porch panel timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of lines - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of lines + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of lines + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of lines vsync-len: description: Vertical sync length panel timing oneOf: - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32 - - maxItems: 1 - items: - description: typical number of lines - - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 3 - maxItems: 3 - items: - description: min, typ, max number of lines + - $ref: /schemas/types.yaml#/definitions/uint32 + maxItems: 1 + items: + description: typical number of lines + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 3 + maxItems: 3 + items: + description: min, typ, max number of lines hsync-active: description: | diff --git a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt deleted file mode 100644 index 10424695aa02..000000000000 --- a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt +++ /dev/null @@ -1,41 +0,0 @@ -Raydium RM67171 OLED LCD panel with MIPI-DSI protocol - -Required properties: -- compatible: "raydium,rm67191" -- reg: virtual channel for MIPI-DSI protocol - must be <0> -- dsi-lanes: number of DSI lanes to be used - must be <3> or <4> -- port: input port node with endpoint definition as - defined in Documentation/devicetree/bindings/graph.txt; - the input port should be connected to a MIPI-DSI device - driver - -Optional properties: -- reset-gpios: a GPIO spec for the RST_B GPIO pin -- v3p3-supply: phandle to 3.3V regulator that powers the VDD_3V3 pin -- v1p8-supply: phandle to 1.8V regulator that powers the VDD_1V8 pin -- width-mm: see panel-common.txt -- height-mm: see panel-common.txt -- video-mode: 0 - burst-mode - 1 - non-burst with sync event - 2 - non-burst with sync pulse - -Example: - - panel@0 { - compatible = "raydium,rm67191"; - reg = <0>; - pinctrl-0 = <&pinctrl_mipi_dsi_0_1_en>; - pinctrl-names = "default"; - reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; - dsi-lanes = <4>; - width-mm = <68>; - height-mm = <121>; - - port { - panel_in: endpoint { - remote-endpoint = <&mipi_out>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml new file mode 100644 index 000000000000..745dd247c409 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/raydium,rm67191.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Raydium RM67171 OLED LCD panel with MIPI-DSI protocol + +maintainers: + - Robert Chiras <robert.chiras@nxp.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: raydium,rm67191 + + reg: true + port: true + reset-gpios: true + width-mm: true + height-mm: true + + dsi-lanes: + description: Number of DSI lanes to be used must be <3> or <4> + enum: [3, 4] + + v3p3-supply: + description: phandle to 3.3V regulator that powers the VDD_3V3 pin + + v1p8-supply: + description: phandle to 1.8V regulator that powers the VDD_1V8 pin + + video-mode: + description: | + 0 - burst-mode + 1 - non-burst with sync event + 2 - non-burst with sync pulse + enum: [0, 1, 2] + +required: + - compatible + - reg + - dsi-lanes + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "raydium,rm67191"; + reg = <0>; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + dsi-lanes = <4>; + width-mm = <68>; + height-mm = <121>; + video-mode = <1>; + + port { + panel_in: endpoint { + remote-endpoint = <&mipi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,amoled-mipi-dsi.yaml b/Documentation/devicetree/bindings/display/panel/samsung,amoled-mipi-dsi.yaml new file mode 100644 index 000000000000..96bdde9298e0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,amoled-mipi-dsi.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,amoled-mipi-dsi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung AMOLED MIPI-DSI panels + +maintainers: + - Hoegeun Kwon <hoegeun.kwon@samsung.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + # Samsung S6E63J0X03 1.63" 320x320 AMOLED panel + - samsung,s6e63j0x03 + # Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + - samsung,s6e3ha2 + # Samsung S6E3HF2 5.65" 1600x2560 AMOLED panel + - samsung,s6e3hf2 + + reg: true + reset-gpios: true + enable-gpios: true + te-gpios: true + + vdd3-supply: + description: I/O voltage supply + + vci-supply: + description: voltage supply for analog circuits + +required: + - compatible + - reg + - vdd3-supply + - vci-supply + - reset-gpios + - enable-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt deleted file mode 100644 index 354d4d1df4ff..000000000000 --- a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.txt +++ /dev/null @@ -1,66 +0,0 @@ -Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus - -Required properties: - - compatible: "samsung,ld9040" - - reg: address of the panel on SPI bus - - vdd3-supply: core voltage supply - - vci-supply: voltage supply for analog circuits - - reset-gpios: a GPIO spec for the reset pin - - display-timings: timings for the connected panel according to [1] - -The panel must obey rules for SPI slave device specified in document [2]. - -Optional properties: - - power-on-delay: delay after turning regulators on [ms] - - reset-delay: delay after reset sequence [ms] - - panel-width-mm: physical panel width [mm] - - panel-height-mm: physical panel height [mm] - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in [3]. This -node should describe panel's video bus. - -[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt -[2]: Documentation/devicetree/bindings/spi/spi-bus.txt -[3]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - - lcd@0 { - compatible = "samsung,ld9040"; - reg = <0>; - vdd3-supply = <&ldo7_reg>; - vci-supply = <&ldo17_reg>; - reset-gpios = <&gpy4 5 0>; - spi-max-frequency = <1200000>; - spi-cpol; - spi-cpha; - power-on-delay = <10>; - reset-delay = <10>; - panel-width-mm = <90>; - panel-height-mm = <154>; - - display-timings { - timing { - clock-frequency = <23492370>; - hactive = <480>; - vactive = <800>; - hback-porch = <16>; - hfront-porch = <16>; - vback-porch = <2>; - vfront-porch = <28>; - hsync-len = <2>; - vsync-len = <1>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <0>; - pixelclk-active = <0>; - }; - }; - - port { - lcd_ep: endpoint { - remote-endpoint = <&fimd_dpi_ep>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,ld9040.yaml b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.yaml new file mode 100644 index 000000000000..060ee27a4749 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,ld9040.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,ld9040.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Andrzej Hajda <a.hajda@samsung.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,ld9040 + + display-timings: true + port: true + reg: true + reset-gpios: true + + vdd3-supply: + description: core voltage supply + + vci-supply: + description: voltage supply for analog circuits + + power-on-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: delay after turning regulators on [ms] + + reset-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: delay after reset sequence [ms] + + panel-width-mm: + description: physical panel width [mm] + + panel-height-mm: + description: physical panel height [mm] + +required: + - compatible + - reg + - vdd3-supply + - vci-supply + - reset-gpios + - display-timings + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + lcd@0 { + compatible = "samsung,ld9040"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + vdd3-supply = <&ldo7_reg>; + vci-supply = <&ldo17_reg>; + reset-gpios = <&gpy4 5 0>; + spi-max-frequency = <1200000>; + spi-cpol; + spi-cpha; + power-on-delay = <10>; + reset-delay = <10>; + panel-width-mm = <90>; + panel-height-mm = <154>; + + display-timings { + timing { + clock-frequency = <23492370>; + hactive = <480>; + vactive = <800>; + hback-porch = <16>; + hfront-porch = <16>; + vback-porch = <2>; + vfront-porch = <28>; + hsync-len = <2>; + vsync-len = <1>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <0>; + pixelclk-active = <0>; + }; + }; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_dpi_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.txt deleted file mode 100644 index b94e366f451b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.txt +++ /dev/null @@ -1,30 +0,0 @@ -Samsung S6D16D0 4" 864x480 AMOLED panel - -Required properties: - - compatible: should be: - "samsung,s6d16d0", - - reg: the virtual channel number of a DSI peripheral - - vdd1-supply: I/O voltage supply - - reset-gpios: a GPIO spec for the reset pin (active low) - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in -media/video-interfaces.txt. This node should describe panel's video bus. - -Example: -&dsi { - ... - - panel@0 { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&foo>; - reset-gpios = <&foo_gpio 0 GPIO_ACTIVE_LOW>; - - port { - panel_in: endpoint { - remote-endpoint = <&dsi_out>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.yaml new file mode 100644 index 000000000000..66d147496bc3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6d16d0.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6d16d0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S6D16D0 4" 864x480 AMOLED panel + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6d16d0 + + port: true + reg: true + reset-gpios: true + + vdd1-supply: + description: I/O voltage supply + +required: + - compatible + - reg + - vdd1-supply + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&foo>; + reset-gpios = <&foo_gpio 0 GPIO_ACTIVE_LOW>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt deleted file mode 100644 index 4acea25c244b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt +++ /dev/null @@ -1,31 +0,0 @@ -Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel -Samsung S6E3HF2 5.65" 1600x2560 AMOLED panel - -Required properties: - - compatible: should be one of: - "samsung,s6e3ha2", - "samsung,s6e3hf2". - - reg: the virtual channel number of a DSI peripheral - - vdd3-supply: I/O voltage supply - - vci-supply: voltage supply for analog circuits - - reset-gpios: a GPIO spec for the reset pin (active low) - - enable-gpios: a GPIO spec for the panel enable pin (active high) - -Optional properties: - - te-gpios: a GPIO spec for the tearing effect synchronization signal - gpio pin (active high) - -Example: -&dsi { - ... - - panel@0 { - compatible = "samsung,s6e3ha2"; - reg = <0>; - vdd3-supply = <&ldo27_reg>; - vci-supply = <&ldo28_reg>; - reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; - enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; - te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt deleted file mode 100644 index 3f1a8392af7f..000000000000 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt +++ /dev/null @@ -1,24 +0,0 @@ -Samsung S6E63J0X03 1.63" 320x320 AMOLED panel (interface: MIPI-DSI command mode) - -Required properties: - - compatible: "samsung,s6e63j0x03" - - reg: the virtual channel number of a DSI peripheral - - vdd3-supply: I/O voltage supply - - vci-supply: voltage supply for analog circuits - - reset-gpios: a GPIO spec for the reset pin (active low) - - te-gpios: a GPIO spec for the tearing effect synchronization signal - gpio pin (active high) - -Example: -&dsi { - ... - - panel@0 { - compatible = "samsung,s6e63j0x03"; - reg = <0>; - vdd3-supply = <&ldo16_reg>; - vci-supply = <&ldo20_reg>; - reset-gpios = <&gpe0 1 GPIO_ACTIVE_LOW>; - te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt deleted file mode 100644 index 9fb9ebeef8e4..000000000000 --- a/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt +++ /dev/null @@ -1,33 +0,0 @@ -Samsung s6e63m0 AMOLED LCD panel - -Required properties: - - compatible: "samsung,s6e63m0" - - reset-gpios: GPIO spec for reset pin - - vdd3-supply: VDD regulator - - vci-supply: VCI regulator - -The panel must obey rules for SPI slave device specified in document [1]. - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in [2]. This -node should describe panel's video bus. - -[1]: Documentation/devicetree/bindings/spi/spi-bus.txt -[2]: Documentation/devicetree/bindings/media/video-interfaces.txt - -Example: - - s6e63m0: display@0 { - compatible = "samsung,s6e63m0"; - reg = <0>; - reset-gpio = <&mp05 5 1>; - vdd3-supply = <&ldo12_reg>; - vci-supply = <&ldo11_reg>; - spi-max-frequency = <1200000>; - - port { - lcd_ep: endpoint { - remote-endpoint = <&fimd_ep>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.yaml b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.yaml new file mode 100644 index 000000000000..1dab80ae1d0a --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/samsung,s6e63m0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung s6e63m0 AMOLED LCD panel + +maintainers: + - Jonathan Bakker <xc-racer2@live.ca> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: samsung,s6e63m0 + + reg: true + reset-gpios: true + port: true + + vdd3-supply: + description: VDD regulator + + vci-supply: + description: VCI regulator + +required: + - compatible + - reset-gpios + - vdd3-supply + - vci-supply + - port + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + display@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + reset-gpios = <&mp05 5 1>; + vdd3-supply = <&ldo12_reg>; + vci-supply = <&ldo11_reg>; + spi-max-frequency = <1200000>; + + port { + lcd_ep: endpoint { + remote-endpoint = <&fimd_ep>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt deleted file mode 100644 index aae57ef36cdd..000000000000 --- a/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt +++ /dev/null @@ -1,23 +0,0 @@ -Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480) TFT with Touch-Panel - -Required properties: -- compatible: should be "sii,43wvf1g". -- "dvdd-supply": 3v3 digital regulator. -- "avdd-supply": 5v analog regulator. - -Optional properties: -- backlight: phandle for the backlight control. - -Example: - - panel { - compatible = "sii,43wvf1g"; - backlight = <&backlight_display>; - dvdd-supply = <®_lcd_3v3>; - avdd-supply = <®_lcd_5v>; - port { - panel_in: endpoint { - remote-endpoint = <&display_out>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.yaml b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.yaml new file mode 100644 index 000000000000..cfaa50cf5f5d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/seiko,43wvf1g.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480) TFT with Touch-Panel + +maintainers: + - Marco Franchi <marco.franchi@nxp.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sii,43wvf1g + + backlight: true + port: true + + dvdd-supply: + description: 3v3 digital regulator + + avdd-supply: + description: 5v analog regulator + +required: + - compatible + - dvdd-supply + - avdd-supply + +additionalProperties: false + +examples: + - | + panel { + compatible = "sii,43wvf1g"; + + backlight = <&backlight_display>; + dvdd-supply = <®_lcd_3v3>; + avdd-supply = <®_lcd_5v>; + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt deleted file mode 100644 index 0f57c3143506..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.txt +++ /dev/null @@ -1,36 +0,0 @@ -Sharp 15" LQ150X1LG11 XGA TFT LCD panel - -Required properties: -- compatible: should be "sharp,lq150x1lg11" -- power-supply: regulator to provide the VCC supply voltage (3.3 volts) - -Optional properties: -- backlight: phandle of the backlight device -- rlud-gpios: a single GPIO for the RL/UD (rotate 180 degrees) pin. -- sellvds-gpios: a single GPIO for the SELLVDS pin. - -If rlud-gpios and/or sellvds-gpios are not specified, the RL/UD and/or SELLVDS -pins are assumed to be handled appropriately by the hardware. - -Example: - - backlight: backlight { - compatible = "pwm-backlight"; - pwms = <&pwm 0 100000>; /* VBR */ - - brightness-levels = <0 20 40 60 80 100>; - default-brightness-level = <2>; - - power-supply = <&vdd_12v_reg>; /* VDD */ - enable-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; /* XSTABY */ - }; - - panel { - compatible = "sharp,lq150x1lg11"; - - power-supply = <&vcc_3v3_reg>; /* VCC */ - - backlight = <&backlight>; - rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ - sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ - }; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.yaml b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.yaml new file mode 100644 index 000000000000..92f2d12f4f4c --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq150x1lg11.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sharp,lq150x1lg11.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sharp 15" LQ150X1LG11 XGA TFT LCD panel + +maintainers: + - Peter Rosin <peda@axentia.se> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sharp,lq150x1lg11 + + power-supply: true + backlight: true + + rlud-gpios: + maxItems: 1 + description: | + GPIO for the RL/UD (rotate 180 degrees) pin. + If rlud-gpios and/or sellvds-gpios are not specified, + the RL/UD and/or SELLVDS pins are assumed to be handled + appropriately by the hardware. + + sellvds-gpios: + maxItems: 1 + description: | + GPIO for the SELLVDS pin. + If rlud-gpios and/or sellvds-gpios are not specified, + the RL/UD and/or SELLVDS pins are assumed to be handled + appropriately by the hardware. + +required: + - compatible + - power-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + panel { + compatible = "sharp,lq150x1lg11"; + + power-supply = <&vcc_3v3_reg>; /* VCC */ + + backlight = <&backlight>; + rlud-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; /* RL/UD */ + sellvds-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; /* SELLVDS */ + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt deleted file mode 100644 index 0cc8981e9d49..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.txt +++ /dev/null @@ -1,43 +0,0 @@ -SHARP LS037V7DW01 TFT-LCD panel -=================================== - -Required properties: -- compatible: "sharp,ls037v7dw01" - -Optional properties: -- label: a symbolic name for the panel -- enable-gpios: a GPIO spec for the optional enable pin. - This pin is the INI pin as specified in the LS037V7DW01.pdf file. -- reset-gpios: a GPIO spec for the optional reset pin. - This pin is the RESB pin as specified in the LS037V7DW01.pdf file. -- mode-gpios: a GPIO - ordered MO, LR, and UD as specified in the LS037V7DW01.pdf file. - -Required nodes: -- Video port for DPI input - -This panel can have zero to five GPIOs to configure to change configuration -between QVGA and VGA mode and the scan direction. As these pins can be also -configured with external pulls, all the GPIOs are considered optional with holes -in the array. - -Example -------- - -Example when connected to a omap2+ based device: - -lcd0: display { - compatible = "sharp,ls037v7dw01"; - power-supply = <&lcd_3v3>; - enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */ - reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */ - mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ - &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ - &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.yaml b/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.yaml new file mode 100644 index 000000000000..8c47a9b0b507 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls037v7dw01.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sharp,ls037v7dw01.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SHARP LS037V7DW01 TFT-LCD panel + +description: | + This panel can have zero to five GPIOs to configure to change configuration + between QVGA and VGA mode and the scan direction. As these pins can be also + configured with external pulls, all the GPIOs are considered optional with holes + in the array. + +maintainers: + - Tony Lindgren <tony@atomide.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sharp,ls037v7dw01 + + label: true + enable-gpios: true + reset-gpios: true + port: true + power-supply: true + + mode-gpios: + minItems: 1 + maxItems: 3 + description: | + GPIO ordered MO, LR, and UD as specified in LS037V7DW01.pdf + This panel can have zero to three GPIOs to configure to + change configuration between QVGA and VGA mode and the + scan direction. As these pins can be also configured + with external pulls, all the GPIOs are considered + optional with holes in the array. + +required: + - compatible + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + lcd0: display { + compatible = "sharp,ls037v7dw01"; + power-supply = <&lcd_3v3>; + enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */ + reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */ + mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ + &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ + &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt deleted file mode 100644 index 3770a111968b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.txt +++ /dev/null @@ -1,22 +0,0 @@ -Sharp Microelectronics 4.3" qHD TFT LCD panel - -Required properties: -- compatible: should be "sharp,ls043t1le01-qhd" -- reg: DSI virtual channel of the peripheral -- power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: -- backlight: phandle of the backlight device attached to the panel -- reset-gpios: a GPIO spec for the reset pin - -Example: - - mdss_dsi@fd922800 { - panel@0 { - compatible = "sharp,ls043t1le01-qhd"; - reg = <0>; - avdd-supply = <&pm8941_l22>; - backlight = <&pm8941_wled>; - reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.yaml b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.yaml new file mode 100644 index 000000000000..a90d0d8bf7c9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,ls043t1le01.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sharp,ls043t1le01.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sharp Microelectronics 4.3" qHD TFT LCD panel + +maintainers: + - Werner Johansson <werner.johansson@sonymobile.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sharp,ls043t1le01-qhd + + reg: true + backlight: true + reset-gpios: true + port: true + + avdd-supply: + description: handle of the regulator that provides the supply voltage + +required: + - compatible + - reg + - avdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "sharp,ls043t1le01-qhd"; + reg = <0>; + avdd-supply = <&pm8941_l22>; + backlight = <&pm8941_wled>; + reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt deleted file mode 100644 index e11208fb7da8..000000000000 --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt +++ /dev/null @@ -1 +0,0 @@ -See panel-common.yaml in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt b/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt deleted file mode 100644 index ccd17597f1f6..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt +++ /dev/null @@ -1,30 +0,0 @@ -Sitronix ST7701 based LCD panels - -ST7701 designed for small and medium sizes of TFT LCD display, is -capable of supporting up to 480RGBX864 in resolution. It provides -several system interfaces like MIPI/RGB/SPI. - -Techstar TS8550B is 480x854, 2-lane MIPI DSI LCD panel which has -inbuilt ST7701 chip. - -Required properties: -- compatible: must be "sitronix,st7701" and one of - * "techstar,ts8550b" -- reset-gpios: a GPIO phandle for the reset pin - -Required properties for techstar,ts8550b: -- reg: DSI virtual channel used by that screen -- VCC-supply: analog regulator for MIPI circuit -- IOVCC-supply: I/O system regulator - -Optional properties: -- backlight: phandle for the backlight control. - -panel@0 { - compatible = "techstar,ts8550b", "sitronix,st7701"; - reg = <0>; - VCC-supply = <®_dldo2>; - IOVCC-supply = <®_dldo2>; - reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ - backlight = <&backlight>; -}; diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7701.yaml b/Documentation/devicetree/bindings/display/panel/sitronix,st7701.yaml new file mode 100644 index 000000000000..6dff59fe4be1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sitronix,st7701.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sitronix,st7701.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sitronix ST7701 based LCD panels + +maintainers: + - Jagan Teki <jagan@amarulasolutions.com> + +description: | + ST7701 designed for small and medium sizes of TFT LCD display, is + capable of supporting up to 480RGBX864 in resolution. It provides + several system interfaces like MIPI/RGB/SPI. + + Techstar TS8550B is 480x854, 2-lane MIPI DSI LCD panel which has + inbuilt ST7701 chip. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + items: + - enum: + - techstar,ts8550b + - const: sitronix,st7701 + + reg: + description: DSI virtual channel used by that screen + maxItems: 1 + + VCC-supply: + description: analog regulator for MIPI circuit + + IOVCC-supply: + description: I/O system regulator + + reset-gpios: true + + backlight: true + +required: + - compatible + - reg + - VCC-supply + - IOVCC-supply + - reset-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "techstar,ts8550b", "sitronix,st7701"; + reg = <0>; + VCC-supply = <®_dldo2>; + IOVCC-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.txt b/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.txt deleted file mode 100644 index c6995dde641b..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.txt +++ /dev/null @@ -1,37 +0,0 @@ -Sitronix ST7789V RGB panel with SPI control bus - -Required properties: - - compatible: "sitronix,st7789v" - - reg: Chip select of the panel on the SPI bus - - reset-gpios: a GPIO phandle for the reset pin - - power-supply: phandle of the regulator that provides the supply voltage - -Optional properties: - - backlight: phandle to the backlight used - -The generic bindings for the SPI slaves documented in [1] also applies - -The device node can contain one 'port' child node with one child -'endpoint' node, according to the bindings defined in [2]. This -node should describe panel's video bus. - -[1]: Documentation/devicetree/bindings/spi/spi-bus.txt -[2]: Documentation/devicetree/bindings/graph.txt - -Example: - -panel@0 { - compatible = "sitronix,st7789v"; - reg = <0>; - reset-gpios = <&pio 6 11 GPIO_ACTIVE_LOW>; - backlight = <&pwm_bl>; - spi-max-frequency = <100000>; - spi-cpol; - spi-cpha; - - port { - panel_input: endpoint { - remote-endpoint = <&tcon0_out_panel>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.yaml b/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.yaml new file mode 100644 index 000000000000..fa46d151e7b3 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sitronix,st7789v.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sitronix,st7789v.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sitronix ST7789V RGB panel with SPI control bus + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Maxime Ripard <mripard@kernel.org> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sitronix,st7789v + + reg: true + reset-gpios: true + power-supply: true + backlight: true + port: true + +required: + - compatible + - reg + - reset-gpios + - power-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "sitronix,st7789v"; + reg = <0>; + reset-gpios = <&pio 6 11 GPIO_ACTIVE_LOW>; + backlight = <&pwm_bl>; + power-supply = <&power>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + port { + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/sony,acx424akp.yaml b/Documentation/devicetree/bindings/display/panel/sony,acx424akp.yaml index 185dcc8fd1f9..78d060097052 100644 --- a/Documentation/devicetree/bindings/display/panel/sony,acx424akp.yaml +++ b/Documentation/devicetree/bindings/display/panel/sony,acx424akp.yaml @@ -18,7 +18,7 @@ properties: reg: true reset-gpios: true vddi-supply: - description: regulator that supplies the vddi voltage + description: regulator that supplies the vddi voltage enforce-video-mode: true required: diff --git a/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt b/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt deleted file mode 100644 index e12333280749..000000000000 --- a/Documentation/devicetree/bindings/display/panel/sony,acx565akm.txt +++ /dev/null @@ -1,30 +0,0 @@ -Sony ACX565AKM SDI Panel -======================== - -Required properties: -- compatible: "sony,acx565akm" - -Optional properties: -- label: a symbolic name for the panel -- reset-gpios: panel reset gpio - -Required nodes: -- Video port for SDI input - -Example -------- - -acx565akm@2 { - compatible = "sony,acx565akm"; - spi-max-frequency = <6000000>; - reg = <2>; - - label = "lcd"; - reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */ - - port { - lcd_in: endpoint { - remote-endpoint = <&sdi_out>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/sony,acx565akm.yaml b/Documentation/devicetree/bindings/display/panel/sony,acx565akm.yaml new file mode 100644 index 000000000000..95d053c548ab --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sony,acx565akm.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/sony,acx565akm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony ACX565AKM SDI Panel + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Tomi Valkeinen <tomi.valkeinen@ti.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: sony,acx565akm + + label: true + reset-gpios: true + port: true + +required: + - compatible + - port + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel@2 { + compatible = "sony,acx565akm"; + spi-max-frequency = <6000000>; + reg = <2>; + + label = "lcd"; + reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */ + + port { + lcd_in: endpoint { + remote-endpoint = <&sdi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt deleted file mode 100644 index 70cd8d18d841..000000000000 --- a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.txt +++ /dev/null @@ -1,4 +0,0 @@ -Startek Electronic Technology Co. KD050C 5.0" WVGA TFT LCD panel - -Required properties: -- compatible: should be "startek,startek-kd050c" diff --git a/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.yaml b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.yaml new file mode 100644 index 000000000000..fd668640afd1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/startek,startek-kd050c.yaml @@ -0,0 +1,33 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/startek,startek-kd050c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Startek Electronic Technology Co. KD050C 5.0" WVGA TFT LCD panel + +maintainers: + - Nikita Kiryanov <nikita@compulab.co.il> + +allOf: + - $ref: panel-dpi.yaml# + +properties: + compatible: + items: + - const: startek,startek-kd050c + - {} # panel-dpi, but not listed here to avoid false select + + backlight: true + enable-gpios: true + height-mm: true + label: true + panel-timing: true + port: true + power-supply: true + reset-gpios: true + width-mm: true + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/display/panel/tpo,td.yaml b/Documentation/devicetree/bindings/display/panel/tpo,td.yaml new file mode 100644 index 000000000000..4aa605613445 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpo,td.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/tpo,td.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toppoly TD Panels + +description: | + The panel must obey the rules for a SPI slave device as specified in + spi/spi-controller.yaml + +maintainers: + - Marek Belisko <marek@goldelico.com> + - H. Nikolaus Schaller <hns@goldelico.com> + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + # Toppoly TD028TTEC1 Panel + - tpo,td028ttec1 + # Toppoly TD043MTEA1 Panel + - tpo,td043mtea1 + + reg: true + label: true + reset-gpios: true + backlight: true + port: true + +required: + - compatible + - port + +unevaluatedProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + + panel: panel@0 { + compatible = "tpo,td043mtea1"; + reg = <0>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + + reset-gpios = <&gpio7 7 0>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt b/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt deleted file mode 100644 index 898e06ecf4ef..000000000000 --- a/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt +++ /dev/null @@ -1,32 +0,0 @@ -Toppoly TD028TTEC1 Panel -======================== - -Required properties: -- compatible: "tpo,td028ttec1" - -Optional properties: -- label: a symbolic name for the panel -- backlight: phandle of the backlight device - -Required nodes: -- Video port for DPI input - -Example -------- - -lcd-panel: td028ttec1@0 { - compatible = "tpo,td028ttec1"; - reg = <0>; - spi-max-frequency = <100000>; - spi-cpol; - spi-cpha; - - label = "lcd"; - backlight = <&backlight>; - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; -}; - diff --git a/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt b/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt deleted file mode 100644 index ec6d62975162..000000000000 --- a/Documentation/devicetree/bindings/display/panel/tpo,td043mtea1.txt +++ /dev/null @@ -1,33 +0,0 @@ -TPO TD043MTEA1 Panel -==================== - -Required properties: -- compatible: "tpo,td043mtea1" -- reset-gpios: panel reset gpio - -Optional properties: -- label: a symbolic name for the panel - -Required nodes: -- Video port for DPI input - -Example -------- - -lcd-panel: panel@0 { - compatible = "tpo,td043mtea1"; - reg = <0>; - spi-max-frequency = <100000>; - spi-cpol; - spi-cpha; - - label = "lcd"; - - reset-gpios = <&gpio7 7 0>; - - port { - lcd_in: endpoint { - remote-endpoint = <&dpi_out>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/panel/visionox,rm69299.yaml b/Documentation/devicetree/bindings/display/panel/visionox,rm69299.yaml new file mode 100644 index 000000000000..b36f39f6b233 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/visionox,rm69299.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/visionox,rm69299.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Visionox model RM69299 Panels Device Tree Bindings. + +maintainers: + - Harigovindan P <harigovi@codeaurora.org> + +description: | + This binding is for display panels using a Visionox RM692999 panel. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: visionox,rm69299-1080p-display + + vdda-supply: + description: | + Phandle of the regulator that provides the vdda supply voltage. + + vdd3p3-supply: + description: | + Phandle of the regulator that provides the vdd3p3 supply voltage. + + port: true + reset-gpios: true + +additionalProperties: false + +required: + - compatible + - vdda-supply + - vdd3p3-supply + - reset-gpios + - port + +examples: + - | + panel { + compatible = "visionox,rm69299-1080p-display"; + + vdda-supply = <&src_pp1800_l8c>; + vdd3p3-supply = <&src_pp2800_l18a>; + + reset-gpios = <&pm6150l_gpio 3 0>; + port { + panel0_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/panel/xinpeng,xpp055c272.yaml b/Documentation/devicetree/bindings/display/panel/xinpeng,xpp055c272.yaml index d9fdb58e06b4..d5c46a3cc2b0 100644 --- a/Documentation/devicetree/bindings/display/panel/xinpeng,xpp055c272.yaml +++ b/Documentation/devicetree/bindings/display/panel/xinpeng,xpp055c272.yaml @@ -19,9 +19,9 @@ properties: backlight: true reset-gpios: true iovcc-supply: - description: regulator that supplies the iovcc voltage + description: regulator that supplies the iovcc voltage vci-supply: - description: regulator that supplies the vci voltage + description: regulator that supplies the vci voltage required: - compatible @@ -37,7 +37,6 @@ examples: dsi { #address-cells = <1>; #size-cells = <0>; - reg = <0xff450000 0x1000>; panel@0 { compatible = "xinpeng,xpp055c272"; diff --git a/Documentation/devicetree/bindings/display/renesas,cmm.yaml b/Documentation/devicetree/bindings/display/renesas,cmm.yaml index a57037b9e9ba..561efaaa5a91 100644 --- a/Documentation/devicetree/bindings/display/renesas,cmm.yaml +++ b/Documentation/devicetree/bindings/display/renesas,cmm.yaml @@ -21,15 +21,15 @@ properties: compatible: oneOf: - items: - - enum: - - renesas,r8a7795-cmm - - renesas,r8a7796-cmm - - renesas,r8a77965-cmm - - renesas,r8a77990-cmm - - renesas,r8a77995-cmm - - const: renesas,rcar-gen3-cmm + - enum: + - renesas,r8a7795-cmm + - renesas,r8a7796-cmm + - renesas,r8a77965-cmm + - renesas,r8a77990-cmm + - renesas,r8a77995-cmm + - const: renesas,rcar-gen3-cmm - items: - - const: renesas,rcar-gen2-cmm + - const: renesas,rcar-gen2-cmm reg: maxItems: 1 @@ -60,7 +60,7 @@ examples: cmm0: cmm@fea40000 { compatible = "renesas,r8a7796-cmm", "renesas,rcar-gen3-cmm"; - reg = <0 0xfea40000 0 0x1000>; + reg = <0xfea40000 0x1000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; clocks = <&cpg CPG_MOD 711>; resets = <&cpg 711>; diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index eb4ae41fe41f..51cd4d162770 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -50,6 +50,14 @@ Required Properties: VSP instance that serves the DU channel, and the channel index identifies the LIF instance in that VSP. +Optional properties: + - resets: A list of phandle + reset-specifier pairs, one for each entry in + the reset-names property. + - reset-names: Names of the resets. This property is model-dependent. + - All but R8A7779 use one reset for a group of one or more successive + channels. The resets must be named "du.x" with "x" being the numerical + index of the lowest channel in the group. + Required nodes: The connections to the DU output video ports are modeled using the OF graph @@ -96,6 +104,8 @@ Example: R8A7795 (R-Car H3) ES2.0 DU <&cpg CPG_MOD 722>, <&cpg CPG_MOD 721>; clock-names = "du.0", "du.1", "du.2", "du.3"; + resets = <&cpg 724>, <&cpg 722>; + reset-names = "du.0", "du.2"; renesas,cmms = <&cmm0>, <&cmm1>, <&cmm2>, <&cmm3>; renesas,vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt deleted file mode 100644 index d1ad31bca8d9..000000000000 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt +++ /dev/null @@ -1,72 +0,0 @@ -Rockchip specific extensions for rk3066 HDMI -============================================ - -Required properties: -- compatible: - "rockchip,rk3066-hdmi"; -- reg: - Physical base address and length of the controller's registers. -- clocks, clock-names: - Phandle to HDMI controller clock, name should be "hclk". -- interrupts: - HDMI interrupt number. -- power-domains: - Phandle to the RK3066_PD_VIO power domain. -- rockchip,grf: - This soc uses GRF regs to switch the HDMI TX input between vop0 and vop1. -- ports: - Contains one port node with two endpoints, numbered 0 and 1, - connected respectively to vop0 and vop1. - Contains one port node with one endpoint - connected to a hdmi-connector node. -- pinctrl-0, pinctrl-name: - Switch the iomux for the HPD/I2C pins to HDMI function. - -Example: - hdmi: hdmi@10116000 { - compatible = "rockchip,rk3066-hdmi"; - reg = <0x10116000 0x2000>; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_HDMI>; - clock-names = "hclk"; - power-domains = <&power RK3066_PD_VIO>; - rockchip,grf = <&grf>; - pinctrl-names = "default"; - pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - hdmi_in: port@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - hdmi_in_vop0: endpoint@0 { - reg = <0>; - remote-endpoint = <&vop0_out_hdmi>; - }; - hdmi_in_vop1: endpoint@1 { - reg = <1>; - remote-endpoint = <&vop1_out_hdmi>; - }; - }; - hdmi_out: port@1 { - reg = <1>; - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; - }; - }; - }; - -&pinctrl { - hdmi { - hdmi_hpd: hdmi-hpd { - rockchip,pins = <0 RK_PA0 1 &pcfg_pull_default>; - }; - hdmii2c_xfer: hdmii2c-xfer { - rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>, - <0 RK_PA2 1 &pcfg_pull_none>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml new file mode 100644 index 000000000000..4110d003ce1f --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/rockchip/rockchip,rk3066-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip rk3066 HDMI controller + +maintainers: + - Sandy Huang <hjc@rock-chips.com> + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + const: rockchip,rk3066-hdmi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: hclk + + pinctrl-0: + maxItems: 2 + + pinctrl-names: + const: default + description: + Switch the iomux for the HPD/I2C pins to HDMI function. + + power-domains: + maxItems: 1 + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + This soc uses GRF regs to switch the HDMI TX input between vop0 and vop1. + + ports: + type: object + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + port@0: + type: object + description: + Port node with two endpoints, numbered 0 and 1, + connected respectively to vop0 and vop1. + + port@1: + type: object + description: + Port node with one endpoint connected to a hdmi-connector node. + + required: + - "#address-cells" + - "#size-cells" + - port@0 + - port@1 + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - pinctrl-0 + - pinctrl-names + - power-domains + - rockchip,grf + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3066a-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/pinctrl/rockchip.h> + #include <dt-bindings/power/rk3066-power.h> + hdmi: hdmi@10116000 { + compatible = "rockchip,rk3066-hdmi"; + reg = <0x10116000 0x2000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HDMI>; + clock-names = "hclk"; + pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>; + pinctrl-names = "default"; + power-domains = <&power RK3066_PD_VIO>; + rockchip,grf = <&grf>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_vop0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vop0_out_hdmi>; + }; + hdmi_in_vop1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vop1_out_hdmi>; + }; + }; + hdmi_out: port@1 { + reg = <1>; + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; + }; + + pinctrl { + hdmi { + hdmi_hpd: hdmi-hpd { + rockchip,pins = <0 RK_PA0 1 &pcfg_pull_default>; + }; + hdmii2c_xfer: hdmii2c-xfer { + rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>, + <0 RK_PA2 1 &pcfg_pull_none>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt deleted file mode 100644 index 8b3a5f514205..000000000000 --- a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt +++ /dev/null @@ -1,74 +0,0 @@ -device-tree bindings for rockchip soc display controller (vop) - -VOP (Visual Output Processor) is the Display Controller for the Rockchip -series of SoCs which transfers the image data from a video memory -buffer to an external LCD interface. - -Required properties: -- compatible: value should be one of the following - "rockchip,rk3036-vop"; - "rockchip,rk3126-vop"; - "rockchip,px30-vop-lit"; - "rockchip,px30-vop-big"; - "rockchip,rk3066-vop"; - "rockchip,rk3188-vop"; - "rockchip,rk3288-vop"; - "rockchip,rk3368-vop"; - "rockchip,rk3366-vop"; - "rockchip,rk3399-vop-big"; - "rockchip,rk3399-vop-lit"; - "rockchip,rk3228-vop"; - "rockchip,rk3328-vop"; - -- reg: Must contain one entry corresponding to the base address and length - of the register space. Can optionally contain a second entry - corresponding to the CRTC gamma LUT address. - -- interrupts: should contain a list of all VOP IP block interrupts in the - order: VSYNC, LCD_SYSTEM. The interrupt specifier - format depends on the interrupt controller used. - -- clocks: must include clock specifiers corresponding to entries in the - clock-names property. - -- clock-names: Must contain - aclk_vop: for ddr buffer transfer. - hclk_vop: for ahb bus to R/W the phy regs. - dclk_vop: pixel clock. - -- resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names: Must include the following entries: - - axi - - ahb - - dclk - -- iommus: required a iommu node - -- port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: -SoC specific DT entry: - vopb: vopb@ff930000 { - compatible = "rockchip,rk3288-vop"; - reg = <0x0 0xff930000 0x0 0x19c>, <0x0 0xff931000 0x0 0x1000>; - interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru ACLK_VOP0>, <&cru DCLK_VOP0>, <&cru HCLK_VOP0>; - clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; - resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; - reset-names = "axi", "ahb", "dclk"; - iommus = <&vopb_mmu>; - vopb_out: port { - #address-cells = <1>; - #size-cells = <0>; - vopb_out_edp: endpoint@0 { - reg = <0>; - remote-endpoint=<&edp_in_vopb>; - }; - vopb_out_hdmi: endpoint@1 { - reg = <1>; - remote-endpoint=<&hdmi_in_vopb>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.yaml new file mode 100644 index 000000000000..1695e3e4bcec --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-vop.yaml @@ -0,0 +1,134 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/rockchip/rockchip-vop.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoC display controller (VOP) + +description: + VOP (Video Output Processor) is the display controller for the Rockchip + series of SoCs which transfers the image data from a video memory + buffer to an external LCD interface. + +maintainers: + - Sandy Huang <hjc@rock-chips.com> + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,px30-vop-big + - rockchip,px30-vop-lit + - rockchip,rk3036-vop + - rockchip,rk3066-vop + - rockchip,rk3126-vop + - rockchip,rk3188-vop + - rockchip,rk3228-vop + - rockchip,rk3288-vop + - rockchip,rk3328-vop + - rockchip,rk3366-vop + - rockchip,rk3368-vop + - rockchip,rk3399-vop-big + - rockchip,rk3399-vop-lit + + reg: + minItems: 1 + items: + - description: + Must contain one entry corresponding to the base address and length + of the register space. + - description: + Can optionally contain a second entry corresponding to + the CRTC gamma LUT address. + + interrupts: + maxItems: 1 + description: + The VOP interrupt is shared by several interrupt sources, such as + frame start (VSYNC), line flag and other status interrupts. + + clocks: + items: + - description: Clock for ddr buffer transfer. + - description: Pixel clock. + - description: Clock for the ahb bus to R/W the phy regs. + + clock-names: + items: + - const: aclk_vop + - const: dclk_vop + - const: hclk_vop + + resets: + maxItems: 3 + + reset-names: + items: + - const: axi + - const: ahb + - const: dclk + + port: + type: object + description: + A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + + assigned-clocks: + maxItems: 2 + + assigned-clock-rates: + maxItems: 2 + + iommus: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + - reset-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3288-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/rk3288-power.h> + vopb: vopb@ff930000 { + compatible = "rockchip,rk3288-vop"; + reg = <0x0 0xff930000 0x0 0x19c>, + <0x0 0xff931000 0x0 0x1000>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_VOP0>, + <&cru DCLK_VOP0>, + <&cru HCLK_VOP0>; + clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; + power-domains = <&power RK3288_PD_VIO>; + resets = <&cru SRST_LCDC1_AXI>, + <&cru SRST_LCDC1_AHB>, + <&cru SRST_LCDC1_DCLK>; + reset-names = "axi", "ahb", "dclk"; + iommus = <&vopb_mmu>; + vopb_out: port { + #address-cells = <1>; + #size-cells = <0>; + vopb_out_edp: endpoint@0 { + reg = <0>; + remote-endpoint=<&edp_in_vopb>; + }; + vopb_out_hdmi: endpoint@1 { + reg = <1>; + remote-endpoint=<&hdmi_in_vopb>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 9999255ac5b6..47319214b5f6 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -40,14 +40,30 @@ of the following host1x client modules: Required properties: - compatible: "nvidia,tegra<chip>-vi" - - reg: Physical base address and length of the controller's registers. + - reg: Physical base address and length of the controller registers. - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. + - clocks: clocks: Must contain one entry, for the module clock. See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - vi + - Tegra20/Tegra30/Tegra114/Tegra124: + - resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must include the following entries: + - vi + - Tegra210: + - power-domains: Must include venc powergate node as vi is in VE partition. + - Tegra210 has CSI part of VI sharing same host interface and register space. + So, VI device node should have CSI child node. + + - csi: mipi csi interface to vi + + Required properties: + - compatible: "nvidia,tegra210-csi" + - reg: Physical base address offset to parent and length of the controller + registers. + - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. + See ../clocks/clock-bindings.txt for details. + - power-domains: Must include sor powergate node as csicil is in + SOR partition. - epp: encoder pre-processor @@ -309,13 +325,44 @@ Example: reset-names = "mpe"; }; - vi { - compatible = "nvidia,tegra20-vi"; - reg = <0x54080000 0x00040000>; - interrupts = <0 69 0x04>; - clocks = <&tegra_car TEGRA20_CLK_VI>; - resets = <&tegra_car 100>; - reset-names = "vi"; + vi@54080000 { + compatible = "nvidia,tegra210-vi"; + reg = <0x0 0x54080000 0x0 0x700>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; + + clocks = <&tegra_car TEGRA210_CLK_VI>; + power-domains = <&pd_venc>; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x0 0x0 0x54080000 0x2000>; + + csi@838 { + compatible = "nvidia,tegra210-csi"; + reg = <0x838 0x1300>; + assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, + <&tegra_car TEGRA210_CLK_CILCD>, + <&tegra_car TEGRA210_CLK_CILE>, + <&tegra_car TEGRA210_CLK_CSI_TPG>; + assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, + <&tegra_car TEGRA210_CLK_PLL_P>, + <&tegra_car TEGRA210_CLK_PLL_P>; + assigned-clock-rates = <102000000>, + <102000000>, + <102000000>, + <972000000>; + + clocks = <&tegra_car TEGRA210_CLK_CSI>, + <&tegra_car TEGRA210_CLK_CILAB>, + <&tegra_car TEGRA210_CLK_CILCD>, + <&tegra_car TEGRA210_CLK_CILE>, + <&tegra_car TEGRA210_CLK_CSI_TPG>; + clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; + power-domains = <&pd_sor>; + }; }; epp { diff --git a/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml b/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml index eb04c2330698..4f9185462ed3 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml +++ b/Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml @@ -88,9 +88,8 @@ properties: - "#size-cells" ti,am65x-oldi-io-ctrl: - allOf: - - $ref: "/schemas/types.yaml#/definitions/phandle-array" - - maxItems: 1 + $ref: "/schemas/types.yaml#/definitions/phandle-array" + maxItems: 1 description: phandle to syscon device node mapping OLDI IO_CTRL registers. The mapped range should point to OLDI_DAT0_IO_CTRL, map it and @@ -123,13 +122,13 @@ examples: dss: dss@4a00000 { compatible = "ti,am65x-dss"; - reg = <0x0 0x04a00000 0x0 0x1000>, /* common */ - <0x0 0x04a02000 0x0 0x1000>, /* vidl1 */ - <0x0 0x04a06000 0x0 0x1000>, /* vid */ - <0x0 0x04a07000 0x0 0x1000>, /* ovr1 */ - <0x0 0x04a08000 0x0 0x1000>, /* ovr2 */ - <0x0 0x04a0a000 0x0 0x1000>, /* vp1 */ - <0x0 0x04a0b000 0x0 0x1000>; /* vp2 */ + reg = <0x04a00000 0x1000>, /* common */ + <0x04a02000 0x1000>, /* vidl1 */ + <0x04a06000 0x1000>, /* vid */ + <0x04a07000 0x1000>, /* ovr1 */ + <0x04a08000 0x1000>, /* ovr2 */ + <0x04a0a000 0x1000>, /* vp1 */ + <0x04a0b000 0x1000>; /* vp2 */ reg-names = "common", "vidl1", "vid", "ovr1", "ovr2", "vp1", "vp2"; ti,am65x-oldi-io-ctrl = <&dss_oldi_io_ctrl>; diff --git a/Documentation/devicetree/bindings/display/ti/ti,j721e-dss.yaml b/Documentation/devicetree/bindings/display/ti/ti,j721e-dss.yaml index eb4b1a266210..bbd76591c180 100644 --- a/Documentation/devicetree/bindings/display/ti/ti,j721e-dss.yaml +++ b/Documentation/devicetree/bindings/display/ti/ti,j721e-dss.yaml @@ -156,23 +156,23 @@ examples: dss: dss@4a00000 { compatible = "ti,j721e-dss"; - reg = <0x00 0x04a00000 0x00 0x10000>, /* common_m */ - <0x00 0x04a10000 0x00 0x10000>, /* common_s0*/ - <0x00 0x04b00000 0x00 0x10000>, /* common_s1*/ - <0x00 0x04b10000 0x00 0x10000>, /* common_s2*/ - <0x00 0x04a20000 0x00 0x10000>, /* vidl1 */ - <0x00 0x04a30000 0x00 0x10000>, /* vidl2 */ - <0x00 0x04a50000 0x00 0x10000>, /* vid1 */ - <0x00 0x04a60000 0x00 0x10000>, /* vid2 */ - <0x00 0x04a70000 0x00 0x10000>, /* ovr1 */ - <0x00 0x04a90000 0x00 0x10000>, /* ovr2 */ - <0x00 0x04ab0000 0x00 0x10000>, /* ovr3 */ - <0x00 0x04ad0000 0x00 0x10000>, /* ovr4 */ - <0x00 0x04a80000 0x00 0x10000>, /* vp1 */ - <0x00 0x04aa0000 0x00 0x10000>, /* vp2 */ - <0x00 0x04ac0000 0x00 0x10000>, /* vp3 */ - <0x00 0x04ae0000 0x00 0x10000>, /* vp4 */ - <0x00 0x04af0000 0x00 0x10000>; /* wb */ + reg = <0x04a00000 0x10000>, /* common_m */ + <0x04a10000 0x10000>, /* common_s0*/ + <0x04b00000 0x10000>, /* common_s1*/ + <0x04b10000 0x10000>, /* common_s2*/ + <0x04a20000 0x10000>, /* vidl1 */ + <0x04a30000 0x10000>, /* vidl2 */ + <0x04a50000 0x10000>, /* vid1 */ + <0x04a60000 0x10000>, /* vid2 */ + <0x04a70000 0x10000>, /* ovr1 */ + <0x04a90000 0x10000>, /* ovr2 */ + <0x04ab0000 0x10000>, /* ovr3 */ + <0x04ad0000 0x10000>, /* ovr4 */ + <0x04a80000 0x10000>, /* vp1 */ + <0x04aa0000 0x10000>, /* vp2 */ + <0x04ac0000 0x10000>, /* vp3 */ + <0x04ae0000 0x10000>, /* vp4 */ + <0x04af0000 0x10000>; /* wb */ reg-names = "common_m", "common_s0", "common_s1", "common_s2", "vidl1", "vidl2","vid1","vid2", |