diff options
Diffstat (limited to 'Documentation/devicetree/bindings/dma/ste-dma40.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/dma/ste-dma40.txt | 138 |
1 files changed, 0 insertions, 138 deletions
diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt deleted file mode 100644 index 99ab5c4d331e..000000000000 --- a/Documentation/devicetree/bindings/dma/ste-dma40.txt +++ /dev/null @@ -1,138 +0,0 @@ -* DMA40 DMA Controller - -Required properties: -- compatible: "stericsson,dma40" -- reg: Address range of the DMAC registers -- reg-names: Names of the above areas to use during resource look-up -- interrupt: Should contain the DMAC interrupt number -- #dma-cells: must be <3> -- memcpy-channels: Channels to be used for memcpy - -Optional properties: -- dma-channels: Number of channels supported by hardware - if not present - the driver will attempt to obtain the information from H/W -- disabled-channels: Channels which can not be used - -Example: - - dma: dma-controller@801c0000 { - compatible = "stericsson,db8500-dma40", "stericsson,dma40"; - reg = <0x801C0000 0x1000 0x40010000 0x800>; - reg-names = "base", "lcpa"; - interrupt-parent = <&intc>; - interrupts = <0 25 0x4>; - - #dma-cells = <2>; - memcpy-channels = <56 57 58 59 60>; - disabled-channels = <12>; - dma-channels = <8>; - }; - -Clients -Required properties: -- dmas: Comma separated list of dma channel requests -- dma-names: Names of the aforementioned requested channels - -Each dmas request consists of 4 cells: - 1. A phandle pointing to the DMA controller - 2. Device signal number, the signal line for single and burst requests - connected from the device to the DMA40 engine - 3. The DMA request line number (only when 'use fixed channel' is set) - 4. A 32bit mask specifying; mode, direction and endianness - [NB: This list will grow] - 0x00000001: Mode: - Logical channel when unset - Physical channel when set - 0x00000002: Direction: - Memory to Device when unset - Device to Memory when set - 0x00000004: Endianness: - Little endian when unset - Big endian when set - 0x00000008: Use fixed channel: - Use automatic channel selection when unset - Use DMA request line number when set - 0x00000010: Set channel as high priority: - Normal priority when unset - High priority when set - -Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are -bidirectional, i.e. the same for RX and TX operations: - -0: SPI controller 0 -1: SD/MMC controller 0 (unused) -2: SD/MMC controller 1 (unused) -3: SD/MMC controller 2 (unused) -4: I2C port 1 -5: I2C port 3 -6: I2C port 2 -7: I2C port 4 -8: Synchronous Serial Port SSP0 -9: Synchronous Serial Port SSP1 -10: Multi-Channel Display Engine MCDE RX -11: UART port 2 -12: UART port 1 -13: UART port 0 -14: Multirate Serial Port MSP2 -15: I2C port 0 -16: USB OTG in/out endpoints 7 & 15 -17: USB OTG in/out endpoints 6 & 14 -18: USB OTG in/out endpoints 5 & 13 -19: USB OTG in/out endpoints 4 & 12 -20: SLIMbus or HSI channel 0 -21: SLIMbus or HSI channel 1 -22: SLIMbus or HSI channel 2 -23: SLIMbus or HSI channel 3 -24: Multimedia DSP SXA0 -25: Multimedia DSP SXA1 -26: Multimedia DSP SXA2 -27: Multimedia DSP SXA3 -28: SD/MM controller 2 -29: SD/MM controller 0 -30: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2 -31: MSP port 0 or SLIMbus channel 0 -32: SD/MM controller 1 -33: SPI controller 2 -34: i2c3 RX2 TX2 -35: SPI controller 1 -36: USB OTG in/out endpoints 3 & 11 -37: USB OTG in/out endpoints 2 & 10 -38: USB OTG in/out endpoints 1 & 9 -39: USB OTG in/out endpoints 8 -40: SPI controller 3 -41: SD/MM controller 3 -42: SD/MM controller 4 -43: SD/MM controller 5 -44: Multimedia DSP SXA4 -45: Multimedia DSP SXA5 -46: SLIMbus channel 8 or Multimedia DSP SXA6 -47: SLIMbus channel 9 or Multimedia DSP SXA7 -48: Crypto Accelerator 1 -49: Crypto Accelerator 1 TX or Hash Accelerator 1 TX -50: Hash Accelerator 1 TX -51: memcpy TX (to be used by the DMA driver for memcpy operations) -52: SLIMbus or HSI channel 4 -53: SLIMbus or HSI channel 5 -54: SLIMbus or HSI channel 6 -55: SLIMbus or HSI channel 7 -56: memcpy (to be used by the DMA driver for memcpy operations) -57: memcpy (to be used by the DMA driver for memcpy operations) -58: memcpy (to be used by the DMA driver for memcpy operations) -59: memcpy (to be used by the DMA driver for memcpy operations) -60: memcpy (to be used by the DMA driver for memcpy operations) -61: Crypto Accelerator 0 -62: Crypto Accelerator 0 TX or Hash Accelerator 0 TX -63: Hash Accelerator 0 TX - -Example: - - uart@80120000 { - compatible = "arm,pl011", "arm,primecell"; - reg = <0x80120000 0x1000>; - interrupts = <0 11 0x4>; - - dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ - <&dma 13 0 0x0>; /* Logical - MemToDev */ - dma-names = "rx", "rx"; - - }; |