1 files changed, 0 insertions, 76 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
deleted file mode 100644
index 59b8dcc118ee..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt
+++ /dev/null
@@ -1,76 +0,0 @@
-* Ingenic JZ4780 NAND/external memory controller (NEMC)
-
-This file documents the device tree bindings for the NEMC external memory
-controller in Ingenic JZ4780
-
-Required properties:
-- compatible: Should be set to one of:
-    "ingenic,jz4740-nemc" (JZ4740)
-    "ingenic,jz4780-nemc" (JZ4780)
-- reg: Should specify the NEMC controller registers location and length.
-- clocks: Clock for the NEMC controller.
-- #address-cells: Must be set to 2.
-- #size-cells: Must be set to 1.
-- ranges: A set of ranges for each bank describing the physical memory layout.
-  Each should specify the following 4 integer values:
-
-    <cs number> 0 <physical address of mapping> <size of mapping>
-
-Each child of the NEMC node describes a device connected to the NEMC.
-
-Required child node properties:
-- reg: Should contain at least one register specifier, given in the following
-  format:
-
-    <cs number> <offset> <size>
-
-  Multiple registers can be specified across multiple banks. This is needed,
-  for example, for packaged NAND devices with multiple dies. Such devices
-  should be grouped into a single node.
-
-Optional child node properties:
-- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits.
-- ingenic,nemc-tAS: Address setup time in nanoseconds.
-- ingenic,nemc-tAH: Address hold time in nanoseconds.
-- ingenic,nemc-tBP: Burst pitch time in nanoseconds.
-- ingenic,nemc-tAW: Access wait time in nanoseconds.
-- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds.
-
-If a child node references multiple banks in its "reg" property, the same value
-for all optional parameters will be configured for all banks. If any optional
-parameters are omitted, they will be left unchanged from whatever they are
-configured to when the NEMC device is probed (which may be the reset value as
-given in the hardware reference manual, or a value configured by the boot
-loader).
-
-Example (NEMC node with a NAND child device attached at CS1):
-
-nemc: nemc@13410000 {
-	compatible = "ingenic,jz4780-nemc";
-	reg = <0x13410000 0x10000>;
-
-	#address-cells = <2>;
-	#size-cells = <1>;
-
-	ranges = <1 0 0x1b000000 0x1000000
-		  2 0 0x1a000000 0x1000000
-		  3 0 0x19000000 0x1000000
-		  4 0 0x18000000 0x1000000
-		  5 0 0x17000000 0x1000000
-		  6 0 0x16000000 0x1000000>;
-
-	clocks = <&cgu JZ4780_CLK_NEMC>;
-
-	nand: nand@1 {
-		compatible = "ingenic,jz4780-nand";
-		reg = <1 0 0x1000000>;
-
-		ingenic,nemc-tAS = <10>;
-		ingenic,nemc-tAH = <5>;
-		ingenic,nemc-tBP = <10>;
-		ingenic,nemc-tAW = <15>;
-		ingenic,nemc-tSTRV = <100>;
-
-		...
-	};
-};