1 files changed, 95 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
new file mode 100644
index 000000000000..2460ccc08237
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip WILC wireless
+
+maintainers:
+  - Adham Abozaeid <adham.abozaeid@microchip.com>
+  - Ajay Singh <ajay.kathat@microchip.com>
+
+description:
+  The wilc1000 chips can be connected via SPI or SDIO. This document
+  describes the binding to connect wilc devices.
+
+properties:
+  compatible:
+    const: microchip,wilc1000
+
+  reg: true
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: phandle to the clock connected on rtc clock line.
+    maxItems: 1
+
+  clock-names:
+    const: rtc
+
+  enable-gpios:
+    maxItems: 1
+    description: Used by wilc1000-spi to determine the GPIO line
+      connected to the ENABLE line.  If specified, reset-gpios
+      must be specified as well as otherwise the driver cannot
+      ensure the timing required between asserting ENABLE
+      and deasserting RESET.  This should be declared as an
+      active-high signal.
+
+  reset-gpios:
+    maxItems: 1
+    description: Used by wilc1000-spi to determine the GPIO line
+      connected to the RESET line.  This should be declared as an
+      active-low signal.
+
+required:
+  - compatible
+  - interrupts
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    spi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      wifi@0 {
+        compatible = "microchip,wilc1000";
+        spi-max-frequency = <48000000>;
+        reg = <0>;
+        interrupt-parent = <&pioC>;
+        interrupts = <27 0>;
+        clocks = <&pck1>;
+        clock-names = "rtc";
+        enable-gpios = <&pioA 5 GPIO_ACTIVE_HIGH>;
+        reset-gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
+      };
+    };
+
+  - |
+    mmc {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      pinctrl-names = "default";
+      pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+      non-removable;
+      vmmc-supply = <&vcc_mmc1_reg>;
+      vqmmc-supply = <&vcc_3v3_reg>;
+      bus-width = <4>;
+      wifi@0 {
+        compatible = "microchip,wilc1000";
+        reg = <0>;
+        interrupt-parent = <&pioC>;
+        interrupts = <27 0>;
+        clocks = <&pck1>;
+        clock-names = "rtc";
+      };
+    };