1 files changed, 115 insertions, 0 deletions
diff --git a/Documentation/networking/device_drivers/neterion/vxge.rst b/Documentation/networking/device_drivers/neterion/vxge.rst
new file mode 100644
index 000000000000..589c6b15c63d
--- /dev/null
+++ b/Documentation/networking/device_drivers/neterion/vxge.rst
@@ -0,0 +1,115 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==============================================================================
+Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
+==============================================================================
+
+.. Contents
+
+  1) Introduction
+  2) Features supported
+  3) Configurable driver parameters
+  4) Troubleshooting
+
+1. Introduction
+===============
+
+This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
+Virtualized Server adapters.
+
+The X3100 series supports four modes of operation, configurable via
+firmware:
+
+	- Single function mode
+	- Multi function mode
+	- SRIOV mode
+	- MRIOV mode
+
+The functions share a 10GbE link and the pci-e bus, but hardly anything else
+inside the ASIC. Features like independent hw reset, statistics, bandwidth/
+priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
+supported independently on each function.
+
+(See below for a complete list of features supported for both IPv4 and IPv6)
+
+2. Features supported
+=====================
+
+i)   Single function mode (up to 17 queues)
+
+ii)  Multi function mode (up to 17 functions)
+
+iii) PCI-SIG's I/O Virtualization
+
+       - Single Root mode: v1.0 (up to 17 functions)
+       - Multi-Root mode: v1.0 (up to 17 functions)
+
+iv)  Jumbo frames
+
+       X3100 Series supports MTU up to 9600 bytes, modifiable using
+       ip command.
+
+v)   Offloads supported: (Enabled by default)
+
+       - Checksum offload (TCP/UDP/IP) on transmit and receive paths
+       - TCP Segmentation Offload (TSO) on transmit path
+       - Generic Receive Offload (GRO) on receive path
+
+vi)  MSI-X: (Enabled by default)
+
+       Resulting in noticeable performance improvement (up to 7% on certain
+       platforms).
+
+vii) NAPI: (Enabled by default)
+
+       For better Rx interrupt moderation.
+
+viii)RTH (Receive Traffic Hash): (Enabled by default)
+
+       Receive side steering for better scaling.
+
+ix)  Statistics
+
+       Comprehensive MAC-level and software statistics displayed using
+       "ethtool -S" option.
+
+x)   Multiple hardware queues: (Enabled by default)
+
+       Up to 17 hardware based transmit and receive data channels, with
+       multiple steering options (transmit multiqueue enabled by default).
+
+3) Configurable driver parameters:
+----------------------------------
+
+i)  max_config_dev
+       Specifies maximum device functions to be enabled.
+
+       Valid range: 1-8
+
+ii) max_config_port
+       Specifies number of ports to be enabled.
+
+       Valid range: 1,2
+
+       Default: 1
+
+iii) max_config_vpath
+       Specifies maximum VPATH(s) configured for each device function.
+
+       Valid range: 1-17
+
+iv) vlan_tag_strip
+       Enables/disables vlan tag stripping from all received tagged frames that
+       are not replicated at the internal L2 switch.
+
+       Valid range: 0,1 (disabled, enabled respectively)
+
+       Default: 1
+
+v)  addr_learn_en
+       Enable learning the mac address of the guest OS interface in
+       virtualization environment.
+
+       Valid range: 0,1 (disabled, enabled respectively)
+
+       Default: 0