diff options
Diffstat (limited to 'arch/x86/kernel/cpu/amd.c')
| -rw-r--r-- | arch/x86/kernel/cpu/amd.c | 46 |
1 files changed, 43 insertions, 3 deletions
diff --git a/arch/x86/kernel/cpu/amd.c b/arch/x86/kernel/cpu/amd.c index a6f88ca1a6b4..2ba9f2d42d8c 100644 --- a/arch/x86/kernel/cpu/amd.c +++ b/arch/x86/kernel/cpu/amd.c @@ -516,7 +516,7 @@ static void bsp_init_amd(struct cpuinfo_x86 *c) setup_force_cpu_cap(X86_FEATURE_ZEN5); break; case 0x50 ... 0x5f: - case 0x90 ... 0xaf: + case 0x80 ... 0xaf: case 0xc0 ... 0xcf: setup_force_cpu_cap(X86_FEATURE_ZEN6); break; @@ -546,6 +546,23 @@ static void early_detect_mem_encrypt(struct cpuinfo_x86 *c) u64 msr; /* + * Mark using WBINVD is needed during kexec on processors that + * support SME. This provides support for performing a successful + * kexec when going from SME inactive to SME active (or vice-versa). + * + * The cache must be cleared so that if there are entries with the + * same physical address, both with and without the encryption bit, + * they don't race each other when flushed and potentially end up + * with the wrong entry being committed to memory. + * + * Test the CPUID bit directly because with mem_encrypt=off the + * BSP will clear the X86_FEATURE_SME bit and the APs will not + * see it set after that. + */ + if (c->extended_cpuid_level >= 0x8000001f && (cpuid_eax(0x8000001f) & BIT(0))) + __this_cpu_write(cache_state_incoherent, true); + + /* * BIOS support is required for SME and SEV. * For SME: If BIOS has enabled SME then adjust x86_phys_bits by * the SME physical address space reduction value. @@ -1018,8 +1035,19 @@ static void init_amd_zen4(struct cpuinfo_x86 *c) } } +static const struct x86_cpu_id zen5_rdseed_microcode[] = { + ZEN_MODEL_STEP_UCODE(0x1a, 0x02, 0x1, 0x0b00215a), + ZEN_MODEL_STEP_UCODE(0x1a, 0x11, 0x0, 0x0b101054), + {}, +}; + static void init_amd_zen5(struct cpuinfo_x86 *c) { + if (!x86_match_min_microcode_rev(zen5_rdseed_microcode)) { + clear_cpu_cap(c, X86_FEATURE_RDSEED); + msr_clear_bit(MSR_AMD64_CPUID_FN_7, 18); + pr_emerg_once("RDSEED32 is broken. Disabling the corresponding CPUID bit.\n"); + } } static void init_amd(struct cpuinfo_x86 *c) @@ -1338,11 +1366,23 @@ static __init int print_s5_reset_status_mmio(void) return 0; value = ioread32(addr); - iounmap(addr); /* Value with "all bits set" is an error response and should be ignored. */ - if (value == U32_MAX) + if (value == U32_MAX) { + iounmap(addr); return 0; + } + + /* + * Clear all reason bits so they won't be retained if the next reset + * does not update the register. Besides, some bits are never cleared by + * hardware so it's software's responsibility to clear them. + * + * Writing the value back effectively clears all reason bits as they are + * write-1-to-clear. + */ + iowrite32(value, addr); + iounmap(addr); for (i = 0; i < ARRAY_SIZE(s5_reset_reason_txt); i++) { if (!(value & BIT(i))) |