diff options
Diffstat (limited to 'drivers/mmc/host/sdhci.c')
| -rw-r--r-- | drivers/mmc/host/sdhci.c | 97 |
1 files changed, 63 insertions, 34 deletions
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 136f9737713d..deafcc56adee 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -749,7 +749,19 @@ static void sdhci_adma_table_pre(struct sdhci_host *host, len -= offset; } - BUG_ON(len > 65536); + /* + * The block layer forces a minimum segment size of PAGE_SIZE, + * so 'len' can be too big here if PAGE_SIZE >= 64KiB. Write + * multiple descriptors, noting that the ADMA table is sized + * for 4KiB chunks anyway, so it will be big enough. + */ + while (len > host->max_adma) { + int n = 32 * 1024; /* 32KiB*/ + + __sdhci_adma_write_desc(host, &desc, addr, n, ADMA2_TRAN_VALID); + addr += n; + len -= n; + } /* tran, valid */ if (len) @@ -1162,9 +1174,11 @@ static inline void sdhci_auto_cmd_select(struct sdhci_host *host, /* * In case of Version 4.10 or later, use of 'Auto CMD Auto * Select' is recommended rather than use of 'Auto CMD12 - * Enable' or 'Auto CMD23 Enable'. + * Enable' or 'Auto CMD23 Enable'. We require Version 4 Mode + * here because some controllers (e.g sdhci-of-dwmshc) expect it. */ - if (host->version >= SDHCI_SPEC_410 && (use_cmd12 || use_cmd23)) { + if (host->version >= SDHCI_SPEC_410 && host->v4_mode && + (use_cmd12 || use_cmd23)) { *mode |= SDHCI_TRNS_AUTO_SEL; ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); @@ -1509,6 +1523,10 @@ static u16 sdhci_get_preset_value(struct sdhci_host *host) u16 preset = 0; switch (host->timing) { + case MMC_TIMING_MMC_HS: + case MMC_TIMING_SD_HS: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_HIGH_SPEED); + break; case MMC_TIMING_UHS_SDR12: preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12); break; @@ -1735,6 +1753,12 @@ void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode, break; case MMC_VDD_32_33: case MMC_VDD_33_34: + /* + * 3.4 ~ 3.6V are valid only for those platforms where it's + * known that the voltage range is supported by hardware. + */ + case MMC_VDD_34_35: + case MMC_VDD_35_36: pwr = SDHCI_POWER_330; break; default: @@ -2646,6 +2670,37 @@ static bool sdhci_request_done(struct sdhci_host *host) } /* + * The controller needs a reset of internal state machines + * upon error conditions. + */ + if (sdhci_needs_reset(host, mrq)) { + /* + * Do not finish until command and data lines are available for + * reset. Note there can only be one other mrq, so it cannot + * also be in mrqs_done, otherwise host->cmd and host->data_cmd + * would both be null. + */ + if (host->cmd || host->data_cmd) { + spin_unlock_irqrestore(&host->lock, flags); + return true; + } + + /* Some controllers need this kick or reset won't work here */ + if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) + /* This is to force an update */ + host->ops->set_clock(host, host->clock); + + /* + * Spec says we should do both at the same time, but Ricoh + * controllers do not like that. + */ + sdhci_do_reset(host, SDHCI_RESET_CMD); + sdhci_do_reset(host, SDHCI_RESET_DATA); + + host->pending_reset = false; + } + + /* * Always unmap the data buffers if they were mapped by * sdhci_prepare_data() whenever we finish with a request. * This avoids leaking DMA mappings on error. @@ -2697,35 +2752,6 @@ static bool sdhci_request_done(struct sdhci_host *host) } } - /* - * The controller needs a reset of internal state machines - * upon error conditions. - */ - if (sdhci_needs_reset(host, mrq)) { - /* - * Do not finish until command and data lines are available for - * reset. Note there can only be one other mrq, so it cannot - * also be in mrqs_done, otherwise host->cmd and host->data_cmd - * would both be null. - */ - if (host->cmd || host->data_cmd) { - spin_unlock_irqrestore(&host->lock, flags); - return true; - } - - /* Some controllers need this kick or reset won't work here */ - if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) - /* This is to force an update */ - host->ops->set_clock(host, host->clock); - - /* Spec says we should do both at the same time, but Ricoh - controllers do not like that. */ - sdhci_do_reset(host, SDHCI_RESET_CMD); - sdhci_do_reset(host, SDHCI_RESET_DATA); - - host->pending_reset = false; - } - host->mrqs_done[i] = NULL; spin_unlock_irqrestore(&host->lock, flags); @@ -3554,6 +3580,7 @@ struct sdhci_host *sdhci_alloc_host(struct device *dev, * descriptor for each segment, plus 1 for a nop end descriptor. */ host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1; + host->max_adma = 65536; return host; } @@ -4207,10 +4234,12 @@ int sdhci_setup_host(struct sdhci_host *host) * be larger than 64 KiB though. */ if (host->flags & SDHCI_USE_ADMA) { - if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC) + if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC) { + host->max_adma = 65532; /* 32-bit alignment */ mmc->max_seg_size = 65535; - else + } else { mmc->max_seg_size = 65536; + } } else { mmc->max_seg_size = mmc->max_req_size; } |